Kaida DONG Jingyan MO Yuhong HE Zhewang MA Xuexia YANG
A compact millimeter-wave three-pole dual-band bandpass filter (BPF) by using substrate-integrated waveguide (SIW) dual-mode cavities is developed in this paper. The proposed filter consists of three SIW dual-mode cavities, in which the TE201 and TE102 modes are used to form two passbands. The center frequencies of the two passbands can be readily changed by varying the lengths and/or widths of the SIW cavities. Meanwhile three transmission zeros are produced with appropriate design of the input and output of the SIW cavities, which increase significantly the isolation between the two passbands and their roll-off rate of attenuations. The dual-band BPF filter is designed, fabricated and measured. The measured center frequencies of the two passbands are 26.75GHz and 31.55GHz, respectively. The 3dB-passbands are 26.35-27.15GHz (3%) and 31.29-31.81GHz (1.6%), respectively, with maximum insertion loss of 2.64dB and 4.2dB, respectively, and return loss larger than 12dB in both passbands. A good agreement between the simulated and measured filter characteristics is obtained.
Shoichi ONODERA Ryo ISHIKAWA Akira SAITOU Kazuhiko HONJO
A frequency-reconfigurable dipole antenna, whose dual resonant frequencies are independently controlled, is introduced. The antenna's conductor consists of radiating conductors, lumped and distributed elements, and varactors. To design the antenna, current distribution, input impedance, and radiation power including higher-order modes, are analyzed for a narrow-angle sectorial antenna embedded with passive elements. To derive the formulae used, radiation power is analyzed in two ways: using Chu's equivalent circuit and the multipole expansion method. Numerical estimations of electrically small antennas show that dual-band antennas are feasible. The dual resonant frequencies are controlled with the embedded series and shunt inductors. A dual-band antenna is fabricated, and measured input impedances agree well with the calculated data. With the configuration, an electrically small 2.5-/5-GHz dual-band reconfig-urable antenna is designed and fabricated, where the reactance values for the series and shunt inductors are controlled with varactors, each connected in series to the inductors. Varying the voltages applied to the varactors varies the measured upper and lower resonant frequencies between 2.6 and 2.9GHz and between 5.1 and 5.3GHz, where the other resonant frequency is kept almost identical. Measured radiation patterns on the H-plane are almost omni-directional for both bands.
ThienLuan HO Seung-Rohk OH HyunJin KIM
A parallel Aho-Corasick (AC) approach, named PAC-k, is proposed for string matching in deep packet inspection (DPI). The proposed approach adopts graphic processing units (GPUs) to perform the string matching in parallel for high throughput. In parallel string matching, the boundary detection problem happens when a pattern is matched across chunks. The PAC-k approach solves the boundary detection problem because the number of characters to be scanned by a thread can reach the longest pattern length. An input string is divided into multiple sub-chunks with k characters. By adopting the new starting position in each sub-chunk for the failure transition, the required number of threads is reduced by a factor of k. Therefore, the overhead of terminating and reassigning threads is also decreased. In order to avoid the unnecessary overlapped scanning with multiple threads, a checking procedure is proposed that decides whether a new starting position is in the sub-chunk. In the experiments with target patterns from Snort and realistic input strings from DEFCON, throughputs are enhanced greatly compared to those of previous AC-based string matching approaches.
Shan GAO Xiaoyuan CAO Takehiro SATO Takaya MIYAZAWA Sota YOSHIDA Noboru YOSHIKANE Takehiro TSURITANI Hiroaki HARAI Satoru OKAMOTO Naoaki YAMANAKA
Software defined networking (SDN) and OpenFlow, which enables the abstraction of vendor/technology-specific attributes, improve the control and management flexibility of optical transport networks. In this paper, we present an interoperability demonstration of SDN/OpenFlow-based optical path control for multi-domain/multi-technology optical transport networks. We also summarize the abstraction approaches proposed for multi-technology network integration at SDN controllers.
Tadao NAKAGAWA Takayuki KOBAYASHI Koichi ISHIHARA Yutaka MIYAMOTO
This paper describes a blind frequency offset estimator (FOE) with wide frequency range for coherent quadrature amplitude modulation (QAM) receivers. The FOE combines a spectrum-based frequency offset estimation algorithm as a coarse estimator with a frequency offset estimation algorithm using the periodogram as a fine estimator. To establish our design methodology, each block of the FOE is rigorously analyzed by using formulas and the minimum fast Fourier transform (FFT) size that generates a frequency spectrum for both the coarse and fine estimators is determined. The coarse estimator's main feature is that all estimation processes are carried out in the frequency domain, which yields convergence more than five times faster than that of conventional estimators. The estimation frequency range of the entire FOE is more than 1.8 times wider than that of conventional FOEs. Experiments on coherent optical 64-ary QAM (64-QAM) reveal that frequency offset estimation can be achieved under a frequency offset value greater than the highest value of the conventional estimation range.
Takuya HIRATA Ryuta NISHINO Shigetoshi NAKATAKE Masaya SHIMOYAMA Masashi MIYAGAWA Ryoichi MIYAUCHI Koichi TANNO Akihiro YAMADA
This paper presents a layout-dependent manufacturability for analog integrated circuits. We focus on the relative variability of an input op-amp-pair used in an instrumentation amplifier (in-amp). We propose a subblock-level matching layout style such that subblocks of the op-amp-pair are superimposed aiming to suppress the relative variability dependent on the layout. We fabricate chips according to five superposed layout styles and evaluate the relative variability in terms of the DC-offset, so that we demonstrate the most effective layout style. Besides, we provide a manufacturability simulation methodology to evaluate the in-amp considering the relative variability of the op-amp-pair based on the measurement results. Comparing the simulation result and the performances of fabricated in-amps, we are convinced our methodology can evaluate the layout-dependency of the manufacturability by the simulation.
This paper proposes and theoretically analyzes the performance of amplify-and-forward (AF) relaying free-space optical (FSO) systems using avalanche photodiode (APD) over atmospheric turbulence channels. APD is used at each relay node and at the destination for optical signal conversion and amplification. Both serial and parallel relaying configurations are considered and the subcarrier binary phase-shift keying (SC-BPSK) signaling is employed. Closed-form expressions for the outage probability and the bit-error rate (BER) of the proposed system are analytically derived, taking into account the accumulating amplification noise as well as the receiver noise at the relay nodes and at the destination. Monte-Carlo simulations are used to validate the theoretical analysis, and an excellent agreement between the analytical and simulation results is confirmed.
Junki KAWAGUCHI Hayato MASHIKO Yukihide KOHIRA
In general-synchronous framework, in which the clock is distributed periodically to each register but not necessarily simultaneously, circuit performance is expected to be improved compared to complete-synchronous framework, in which the clock is distributed periodically and simultaneously to each register. To improve the circuit performance more, logic synthesis for general-synchronous framework is required. In this paper, under the assumption that any clock schedule is realized by an ideal clock distribution circuit, when two or more cell libraries are available, a technology mapping method which assigns a cell to each gate in the given logic circuit by using integer linear programming is proposed. In experiments, we show the effectiveness of the proposed technology mapping method.
Hiroshi HASEGAWA Yojiro MORI Ken-ichi SATO
A novel resilient coarse granularity optical routing network architecture that adopts finely granular protection and finely granular add/drop is presented. The routing scheme defines optical pipes such that multiple optical paths can be carried by each pipe and can be dropped or added at any node on the route of a pipe. The routing scheme also makes it possible to enhance frequency utilization within pipes, by denser path packing in the frequency domain, as we recently verified. We develop a static network design algorithm that simultaneously realizes the independence of working and backup paths and pipe location optimization to efficiently carry these paths. The design algorithm first sequentially accommodates optical paths into the network, then tries to eliminate sparsely utilized fibers and iteratively optimizes frequency slot/wavelength assignment in each coarse granular pipe so as to limit the impairment caused by dropping the optical paths adjacent in the frequency domain. Numerical experiments elucidate that the number of fibers in a network can be reduced by up to 20% for 400Gbps channels without any modification in hardware.
This paper considers on-demand WiFi wake-up where a wake-up receiver is installed into each WiFi device. The wake-up receiver detects a wake-up call by finding the predefined length of WiFi frames, which corresponds to a wake-up ID, through envelope detection with limited signal processing. Since each wake-up receiver continuously observes the WiFi channel, an adverse event of False Positive (FP), where a WiFi device is falsely turned on without actual wake-up calls, can occur when the length of non-wake-up, background data frames match with predefined length. In this paper, we suggest using the received signal strength (RSS) of WiFi frames to differentiate the real and false wake-up calls. The proposed scheme exploits the correlation among RSSs of WiFi frames received from a single station located in a fixed position. Using measured RSS data obtained under various settings and different degrees of mobility, we investigate not only the FP reduction rate but also its impact on the probability of detecting real wake-up calls. We also present experimental results obtained with our prototype in which the proposed scheme is implemented.
SM3 is a hash function standard defined by China. Unlike SHA-1 and SHA-2, it is hard for SM3 to speed up the throughput because it has more complicated compression function than other hash algorithm. In this paper, we propose a 4-round-in-1 structure to reduce the number of rounds, and a logical simplifying to move 3 adders and 3 XOR gates from critical path to the non-critical path. Based in SMIC 65nm CMOS technology, the throughput of SM3 can achieve 6.54Gbps which is higher than that of the reported designs.
Ryota SATO Keimei KAINO Jun SONODA
Pre-Cantor bar, the one-dimensional fractal media, consists of two kinds of materials. Using the transmission-line theory we will explain the double-exponential behavior of the minimum of the transmittance as a function of the stage number n, and obtain formulae of two kinds of scaling behaviors of the transmittance. From numerical calculations for n=1 to 5 we will find that the maximum of field amplitudes of resonance which increases double-exponentially with n is well estimated by the theoretical upper bound. We will show that after sorting field amplitudes for resonance frequencies of the 5th stage their distribution is a staircase function of the index.
Ryan IMANSYAH Tatsushi TANAKA Luke HIMBELE Haisong JIANG Kiichi HAMAMOTO
We have proposed and demonstrated the principle of optical mode switch. However, the crosstalk between modes has not yet reported due to the difficulty of mode recognition and distinction. To accomplish this mode crosstalk evaluation, we integrated multimode interference (MMI) mode filter with the optical mode switch in this work. As a result, for the both TE and TM modes, the crosstalk of approximately -10 dB has been evaluated experimentally.
Gihyoun LEE Sung Dae NA KiWoong SEONG Jin-Ho CHO Myoung Nam KIM
Because wavelet transforms have the characteristic of decomposing signals that are similar to the human acoustic system, speech enhancement algorithms that are based on wavelet shrinkage are widely used. In this paper, we propose a new speech enhancement algorithm of hearing aids based on wavelet shrinkage. The algorithm has multi-band threshold value and a new wavelet shrinkage function for recursive noise reduction. We performed experiments using various types of authorized speech and noise signals, and our results show that the proposed algorithm achieves significantly better performances compared with other recently proposed speech enhancement algorithms using wavelet shrinkage.
Aslhan AKYOL Mehmet HACIBEYOĞLU Bekir KARLIK
With the increase of network components connected to the Internet, the need to ensure secure connectivity is becoming increasingly vital. Intrusion Detection Systems (IDSs) are one of the common security components that identify security violations. This paper proposes a novel multilevel hybrid classifier that uses different feature sets on each classifier. It presents the Discernibility Function based Feature Selection method and two classifiers involving multilayer perceptron (MLP) and decision tree (C4.5). Experiments are conducted on the KDD'99 Cup and ISCX datasets, and the proposal demonstrates better performance than individual classifiers and other proposed hybrid classifiers. The proposed method provides significant improvement in the detection rates of attack classes and Cost Per Example (CPE) which was the primary evaluation method in the KDD'99 Cup competition.
Miyoung KANG Jin-Young CHOI Inhye KANG Hee Hwan KWAK So Jin AHN Myung-Ki SHIN
SDN (Software-Defined Networking) enables software applications to program individual network devices dynamically and therefore control the behavior of the network as a whole. Incomplete programming and/or inconsistency with the network policy of SDN software applications may lead to verification issues. The objective of this paper is to describe the formal modeling that uses the process algebra called pACSR and then suggest a method to verify the firewall application running on top of the SDN controller. The firewall rules are translated into a pACSR process which acts as the specification, and packet's behaviors in SDN are also translated to a pACSR process which is a role as the implementation. Then we prove the correctness by checking whether the parallel composition of two pACSR processes is deadlock-free. Moreover, in the case of network topology changes, our verification can be directly applied to check whether any mismatches or inconsistencies will occur.
Mauricio KUGLER Teemu TOSSAVAINEN Miku NAKATSU Susumu KUROYANAGI Akira IWATA
The development of assistive devices for automated sound recognition is an important field of research and has been receiving increased attention. However, there are still very few methods specifically developed for identifying environmental sounds. The majority of the existing approaches try to adapt speech recognition techniques for the task, usually incurring high computational complexity. This paper proposes a sound recognition method dedicated to environmental sounds, designed with its main focus on embedded applications. The pre-processing stage is loosely based on the human hearing system, while a robust set of binary features permits a simple k-NN classifier to be used. This gives the system the capability of in-field learning, by which new sounds can be simply added to the reference set in real-time, greatly improving its usability. The system was implemented in an FPGA based platform, developed in-house specifically for this application. The design of the proposed method took into consideration several restrictions imposed by the hardware, such as limited computing power and memory, and supports up to 12 reference sounds of around 5.3 s each. Experimental results were performed in a database of 29 sounds. Sensitivity and specificity were evaluated over several random subsets of these signals. The obtained values for sensitivity and specificity, without additional noise, were, respectively, 0.957 and 0.918. With the addition of +6 dB of pink noise, sensitivity and specificity were 0.822 and 0.942, respectively. The in-field learning strategy presented no significant change in sensitivity and a total decrease of 5.4% in specificity when progressively increasing the number of reference sounds from 1 to 9 under noisy conditions. The minimal signal-to-noise ration required by the prototype to correctly recognize sounds was between -8 dB and 3 dB. These results show that the proposed method and implementation have great potential for several real life applications.
Let Fq be a finite field of cardinality q, R=Fq[u]/
Performance evaluation of an improved multiband impulse radio ultra-wideband (MIR UWB) system based on sub-band selection is proposed in this paper. In the improved scheme, a data mapping algorithm is introduced to a conventional MIR UWB system, and out of all the sub-bands, only partial ones are selected to transmit information data, which can improve the flexibility of sub-bands/spectrum allocation, avoid interference and provide a variety of data rates. Given diagrams of a transmitter and receiver, the exact bit error rate (BER) of the improved system is derived. A comparison of system performance between the improved MIR UWB system and the conventional MIR UWB system is presented in different channels. Simulation results show that the improved system can achieve the same data rate and better BER performance than the conventional MIR UWB system under additive white Gaussian noise (AWGN), multipath fading and interference coexistence channels. In addition, different data transmission rates and BER performances can be easily achieved by an appropriate choice of system parameters.
Lian ZENG Tieyuan PAN Xin JIANG Takahiro WATANABE
As the semiconductor technology continues to develop, hundreds of cores will be deployed on a single die in the future Chip-Multiprocessors (CMPs) design. Three-Dimensional Network-on-Chips (3D NoCs) has become an attractive solution which can provide impressive high performance. An efficient and deadlock-free routing algorithm is a critical to achieve the high performance of network-on-chip. Traditional methods based on deterministic and turn model are deadlock-free, but they are unable to distribute the traffic loads over the network. In this paper, we propose an efficient, adaptive and deadlock-free algorithm (EAR) based on a novel routing selection strategy in 3D NoC, which can distribute the traffic loads not only in intra-layers but also in inter-layers according to congestion information and path diversity. Simulation results show that the proposed method achieves the significant performance improvement compared with others.