In automotive frequency modulated continuous wave (FMCW) radar based on multiple ramps with different slope, an effective pairing algorithm is required to simultaneously detect the target range and velocity. That is, as finding beat-frequencies intersecting at a single point of the range-Doppler map, we extract the range and velocity of a target. Unlike the ideal case, however, in a real radar system, even though multiple beat frequencies are originated from the same target, these beat frequencies have many different intersection values, resulting in mismatch pairing during the pairing step. Moreover, this problem also reduces the detection accuracy and the radar detection performance. In this study, we found that mismatch pairing is caused by the round-off errors of the range-beat frequency and Doppler frequency, as well as their various combinations in the discrete frequency domain. We also investigated the effect of mismatch pairing on detection performance, and proposed a new approach to minimize this problem. First, we propose integer and half-integer frequency position-based pairing method during extraction of the range and Doppler frequencies in each ramp to increase detection accuracy. Second, we propose a window-based pairing method to identify the same target from range-Doppler frequencies extracted in the first step. We also find the appropriate window size to overcome pairing mismatch. Finally, we propose the method to obtain a higher accuracy of range and velocity by weighting the values determined in one window. To verify the detection performance of the proposed method by comparison with the typical method, simulations were conducted. Then, in a real field test using the developed radar prototype, the detection probability of the proposed algorithm showed more than 60% improvement in comparison with the conventional method.

The combined linear frequency modulation continuous wave (LFMCW) and inverse synthetic aperture radar (ISAR) can be used for imaging long-distance targets because of its long-distance and high resolution imaging abilities. In this paper, we find and study the dechirp distortion phenomenon (DDP) for imaging long-distance targets by a dechirp-on-receive LFMCW radar. If the targets are very far from the radar, the maximum delay-time is not much smaller than a single sweep duration, and the dechirp distortion is triggered since the distance of the target is unknown in a LFMCW-ISAR system. DDP cannot be ignored in long-distance imaging because double images of a target appear in the frequency domain, which reduces resolution and degrades image quality. A novel LFMCW-ISAR signal model is established to analyze DDP and its negative effects on long-distance target imaging. Using the proportionately distributed energy of double images, the authors propose a method to correct dechirp distortion. In addition, the applicable scope of the proposed method is also discussed. Simulation results validate the theoretical analysis and the effectiveness of the proposed method.

The Lee complete ρ weight enumerator and the exact complete ρ weight enumerator over Mn×s(Fl+vFl+v2Fl)(v3=v) are defined, and the MacWilliams identities with respect to RT metric for these two weight enumerators of linear codes over Mn×s(Fl+vFl+v2Fl) are obtained, respectively. Finally, we give two examples to illustrate the obtained results.

In this paper, a priority control problem between uplink and downlink flows in IEEE 802.11 wireless LANs is considered. The minimum contention window size (CWmin) has a nonnegative integer value. CWmin control scheme is one of the solutions for priority control to achieve the fairness between links. However, it has the problem that CWmin control scheme cannot achieve precise priority control when the CWmin values become small. As the solution of this problem, this paper proposes a new CWmin control method called a virtual continuous CWmin control (VCCC) scheme. The key concept of this method is that it involves the use of small and large CWmin values probabilistically. The proposed scheme realizes the expected value of CWmin as a nonnegative real number and solves the precise priority control problem. Moreover, we proposed a theoretical analysis model for the proposed VCCC scheme. Computer simulation results show that the proposed scheme improves the throughput performance and achieves fairness between the uplink and the downlink flows in an infrastructure mode of the IEEE 802.11 based wireless LAN. Throughput of the proposed scheme is 31% higher than that of a conventional scheme when the number of wireless stations is 18. The difference between the theoretical analysis results and computer simulation results of the throughput is within 1% when the number of STAs is less than 10.

An S-band GaN on Si based 1kW-class SSPA system for space wireless applications is proposed. Since high-efficiency and high-reliability amplifier is one of the most important technologies for power and communication systems in a future space base station on a planet, compact, high-power, and high-efficiency SSPA is strongly requested instead of TWTA. Thus, we adopt GaN on Si based amplifier due to its remarkable material properties. At the beginning, thermal vacuum and radiation test of GaN on Si are conducted so as to confirm the space applicability. Fabricated SSPA system consists of eight 200W HPAs and coaxial waveguide power combiner. It achieves high efficiency such as 57% of drain efficiency and 87% of combining efficiency when RF output power achieves more than 60dBm. Furthermore, long-term stable operation and good phase noise characteristics are also confirmed.

Nowadays, error control codes have become an essential technique to improve the reliability of various digital systems. A new type error control codes called m-spotty byte error control codes are applied to computer memory systems. These codes are essential to make the memory systems reliable. Here, we introduce the m-spotty Rosenbloom-Tsfasman weights and m-spotty Rosenbloom-Tsfasman weight enumerator of linear codes over Fq[u]/(uk) with uk=0. We also derive a MacWilliams type identity for m-spotty Rosenbloom-Tsfasman weight enumerator.

The research on body-centric wireless communications (BCWCs) is becoming very hot because of numerous applications, especially the application of E-health systems. Therefore, a small multi-band and low-profile planar inverted-F antenna (PIFA) with tuning function is presented for BCWCs in this paper. In order to achieve multi-band operation, there are two branches in the antenna: the longer branch low frequency band (950–956 MHz), and the shorter branch with a varactor diode embedded for high frequency bands. By supplying different DC voltages, the capacitance of the varactor diode varies, so the resonant frequency can be tuned without changing the dimension of the antenna. While the bias is set at 6 V and 14 V, WiMAX and ISM bands can be covered, respectively. From the radiation patterns, at 950 MHz, the proposed antenna is suitable for on-body communications, and in WiMAX and ISM bands, they are suitable for both on-body and off-body communications.

A 24-GHz continuous wave (CW) radar with three vertically switched beam antennas for monitoring different range segments has been newly proposed and developed as a means to detect intruders in a fan-shaped ground area with 90 degs. in azimuth and over 10 m in range. This radar can detect moving targets and measure their positions from a tampering-proof height of about 5 m by taking advantage of a two-frequency-CW modulation technique and monopulse scheme used to achieve the wide azimuth coverage. The radar module consists of microstrip-patch planar antennas and monolithic microwave integrated circuits (MMICs), which are placed on the opposite side of a single metal plate to attain compact size and lower cost. An experimental radar successfully detected a human intruder with a position accuracy of 50 cm when moving at 1.4 m/s.

A bidirectional amplification module has been proposed for use in IP-over-CWDM networks. The module is based on a bidirectional erbium-doped fiber amplifier. The loss compensation characteristics of the module obtained in a bidirectional IP transmission experiment confirmed that the losses of the optical node and the transmission fiber in the network can be compensated for effectively by the module making it possible to increase the number of nodes and the total fiber length of the network.

Practitioners of the Jiro Kawakita (KJ) method, a method for organizing ideas, typically use paper labels and four-colored ball-point pens to record their ideas during the creative thinking process. A similar approach is used in group KJ method sessions; however, the effectiveness of capturing and sharing the diagrams and information is limited because of the large amount of paper required. Considering the merits of the conventional paper-pen approach and the demand for quick sharing of diagrams after a session, we designed and implemented a system to digitize group KJ sessions--not just the diagrams but also the details of the creative process. We used digital pens during the session to capture the position and orientation of labels as well as their content. We confirmed the efficiency of our system by applying it to several GKJ sessions.

Network coding is a promising technique for improving system performance in wireless multihop networks. In this paper, the throughput and fairness in single-relay multi-user wireless networks are evaluated. The carrier sense multiple access with collision avoidance (CSMA/CA) protocol and network coding are used in the medium access control (MAC) sublayer in such networks. The fairness of wireless medium access among stations (STAs), the access point (AP), and the relay station (RS) results in asymmetric bidirectional flows via the RS; as a result the wireless throughput decreases substantially. To overcome this problem, an autonomous optimization of minimum contention window size is developed for CSMA/CA and network coding to assign appropriate transmission opportunities to both the AP and RS. By optimizing the minimum contention window size according to the number of STAs, the wireless throughput in single-relay multi-user networks can be improved and the fairness between bidirectional flows via the RS can be achieved. Numerical analysis and computer simulations enable us to evaluate the performances of CSMA/CA and network coding in single-relay multi-user wireless networks.

The tiled-display system has been used as a Computer Supported Cooperative Work (CSCW) environment, in which multiple local (and/or remote) participants cooperate using some shared applications whose outputs are displayed on a large-scale and high-resolution tiled-display, which is controlled by a cluster of PC's, one PC per display. In order to make the collaboration effective, each remote participant should be aware of all CSCW activities on the titled display system in real-time. This paper presents a capturing and delivering mechanism of all activities on titled-display system to remote participants in real-time. In the proposed mechanism, the screen images of all PC's are periodically captured and delivered to the Merging Server that maintains separate buffers to store the captured images from the PCs. The mechanism selects one tile image from each buffer, merges the images to make a screen shot of the whole tiled-display, clips a Region of Interest (ROI), compresses and streams it to remote participants in real-time. A technical challenge in the proposed mechanism is how to select a set of tile images, one from each buffer, for merging so that the tile images displayed at the same time on the tiled-display can be properly merged together. This paper presents three selection algorithms; a sequential selection algorithm, a capturing time based algorithm, and a capturing time and visual consistency based algorithm. It also proposes a mechanism of providing several virtual cameras on tiled-display system to remote participants by concurrently clipping several different ROI's from the same merged tiled-display images, and delivering them after compressing with video encoders requested by the remote participants. By interactively changing and resizing his/her own ROI, a remote participant can check the activities on the tiled-display effectively. Experiments on a 32 tiled-display system show that the proposed merging algorithm can build a tiled-display image stream synchronously, and the ROI-based clipping and delivering mechanism can provide individual views on the tiled-display system to multiple remote participants in real-time.

M-spotty byte error control codes are very effective for correcting/detecting errors in semiconductor memory systems that employ recent high-density RAM chips with wide I/O data (e.g., 8, 16, or 32 bits). In this case, the width of the I/O data is one byte. A spotty byte error is defined as random t-bit errors within a byte of length b bits, where 1 ≤ t ≤ b. Then, an error is called an m-spotty byte error if at least one spotty byte error is present in a byte. M-spotty byte error control codes are characterized by the m-spotty distance, which includes the Hamming distance as a special case for t = 1 or t = b. The MacWilliams identity provides the relationship between the weight distribution of a code and that of its dual code. The present paper presents the MacWilliams identity for the m-spotty weight enumerator of m-spotty byte error control codes. In addition, the present paper clarifies that the indicated identity includes the MacWilliams identity for the Hamming weight enumerator as a special case.

This paper presents a coherent decomposition scheme for polarimetric SAR data. Coherent decomposition means the decomposition is applied to a single or a few scattering matrix data. Based on the scattering matrix acquired with an FM-CW polarimetric SAR system, we have devised a simple decomposition technique using the coherency matrix for the purpose of identifying scatterers. This paper presents the decomposition technique and some decomposition results obtained by a fully polarimetric FM-CW radar. It is shown the scattering mechanisms are well recovered and the orientation angles of wire scatterer are precisely measured.

Monolithically integrated four-channel distributed feedback (DFB) laser array has been fabricated by metal organic vapor phase epitaxy (MOVPE) selective area growth for 1.55 µm coarse-wavelength division multiplexing (CWDM) systems. Wide-stripe MOVPE selective area growth and electron-beam lithography are used to obtain wide CWDM channel spacing of 20 nm. Compared to hybrid integration of discrete lasers, monolithic integration of laser array on a single substrate greatly simplifies device alignment and packaging process.

In this paper, the thermal characteristic of the GaN HFETs has been analyzed using the hybrid finite element method (FEM). Both the steady and transient state thermal operations are quantitatively studied with the effects of temperature-dependent thermal conductivities of GaN and the substrate materials properly treated. The temperature distribution and the maximum temperatures of the HFETs operated under excitations of continuous-waves (CW) and pulsed-waves (PW) including double exponential shape PW such as electromagnetic pulse (EMP) and ultra-wideband (UWB) signal are studied and compared.

High-resolution FMCW reflectometry is often realized by sampling the beat signal with a clock signal generated from an auxiliary interferometer. The drawback of this system is that the measurement range is limited to less than half of the optical path difference of the auxiliary interferometer to satisfy the Sampling theorem. We propose and demonstrate a method to extend the measurement range of the system. The clock signal gerenerated from the auxiliary interferometer is electronically frequency-multipled by using a PLL circuit. The measurement range is experimentally extended by a factor of 20 while keeping high spatial resolution, and is theoretically extended by a factor of 128. The advantage of the proposed system is that the optical path difference of the auxiliary interferometer can be kept short, which is very effective for obtaining the stable and low time-jitter clock signal.

Time-Division-Multiplexing (TDM) is usually aimed at digital signals, while Continuous Wave Time-Division- Multiplexing (i.e. CWTDM) presented in this paper mainly addresses the problem of multiple continuous signals to share a channel. According to the idea in Ref.[1], this paper proposes a novel method for implementing CWTDM, which can make multiple band-limited continuous signals time-division-multiplexed into one continuous signal without significantly expanding the frequency band. The new method has several important applications. In particular, it can be used to implement an on-board FDMA-CWTDM conversion to develop a new system of satellite communications with more efficient performance.

Currently, multi-party video conference does not provide equivalent quality in comparison to face-to-face conference. One assumed reason is that participants cannot be aware of "who is focusing on whom". We introduce virtual space to a multi-party conference system, allocating avatars in a space. We also introduce intuitive input interface using motion processor in order to construct a multi-party conference system, which the user can use without being aware of it. A new displaying method is essential for this system, and we introduce a way by which a user can obtain the feedback of which user he/she is focusing on. We introduce e-MulCS as the system that fulfils these proposals. By comparing this system with the video conference system, the results show that our system supports the intuitive multi-party communication better.

We have proposed and theoretically verified a 2R (reshaping and regeneration) limiter circuit using continuous wave (CW) holding beam for cross-gain modulation (XGM) wavelength converter, through simulation. The gain clamping effect of semiconductor optical amplifier (SOA), which is caused by CW holding beam injected into SOA, was used to obtain the accurate optical gain and phase conditions for SOA's in 2R limiter circuit. XGM wavelength converter with the proposed 2R limiter circuit provides higher extinction ratio (ER) as well as more enhanced operation speed than any other wavelength converter. Our numerical results show that after the wavelength-converted signal from XGM wavelength converter passed the 2R limiter circuit, it was re-inverted with the improved ER of 30 dB at 5 Gb/s. In case of high-speed operation, great enhancement to decrease power penalty of about 12 dB was shown at 10 Gb/s.