In this paper, we propose filter-and-forward beamforming (FF-BF) for cognitive two-way relay networks in which secondary users employ an orthogonal frequency-division multiplexing (OFDM) system. Secondary transceivers communicate with each other through multiple relays to obtain BF gain as well as to suppress the interference between the primary and secondary users who share the same spectrum. We consider two FF-BF design methods to optimize the relay filter. The first method enhances the quality of service of the secondary network by maximizing the worst subcarrier signal-to-interference-plus-noise ratio (SINR) subject to transmit power constraints. The second method suppresses the interference from the secondary network to the primary network through the minimization of the relay transmission power subject to subcarrier SINR constraints. Simulation results show that the proposed FF-BF improves system performance in comparison to amplify-and-forward relay BF.

Streaming services that use TCP have increased; however, throughput is unstable due to congestion control caused by packet loss when TCP is used. Thus, TCP control to secure a required transmission rate for streaming communication using Forward Error Correction (FEC) technology (TCP-AFEC) has been proposed. TCP-AFEC can control the appropriate transmission rate according to network conditions using a combination of TCP congestion control and FEC. However, TCP-AFEC was not developed for wireless Local Area Network (LAN) environments; thus, it requires a certain time to set the appropriate redundancy and cannot obtain the required throughput. In this paper, we demonstrate the drawbacks of TCP-AFEC in wireless LAN environments. Then, we propose a redundancy setting method that can secure the required throughput for FEC, i.e., TCP-TFEC. Finally, we show that TCP-TFEC can secure more stable throughput than TCP-AFEC.

In this paper, a multichannel speech enhancement system which adopts a denoising auto-encoder as part of the beamformer is proposed. The proposed structure of the generalized sidelobe canceller generates enhanced multi-channel signals, instead of merely one channel, to which the following denoising auto-encoder can be applied. Because the beamformer exploits spatial information and compensates for differences in the transfer functions of each channel, the proposed system is expected to resolve the difficulty of modelling relative transfer functions consisting of complex numbers which are hard to model with a denoising auto-encoder. As a result, the modelling capability of the denoising auto-encoder can concentrate on removing the artefacts caused by the beamformer. Unlike conventional beamformers, which combine these artefacts into one channel, they remain separated for each channel in the proposed method. As a result, the denoising auto-encoder can remove the artefacts by referring to other channels. Experimental results prove that the proposed structure is effective for the six-channel data in CHiME, as indicated by improvements in terms of speech enhancement and word error rate in automatic speech recognition.

In this paper, we consider the crosscorrelation of two interleaved sequences of period 4N constructed by Gong and Tang which has been proved to possess optimal autocorrelation. Results show that the interleaved sequences achieve the largest crosscorrelation value 4.

Real-time and reliable radio communication is essential for wireless control systems (WCS). In WCS, preambles create significant overhead and affect the real-time capability since payloads are typically small. To shorten the preamble transmission time in OFDM systems, previous works have considered adopting either time-direction extrapolation (TDE) or frequency-direction interpolation (FDI) for channel estimation which however result in poor performance in fast fading channels and frequency-selective fading channels, respectively. In this work, we propose a subcarrier-selectable short preamble (SSSP) by introducing selectability to subcarrier sampling patterns of a preamble such that it can provide full sampling coverage of all subcarriers with several preamble transmissions. In addition, we introduce adaptability to a channel estimation algorithm for the SSSP so that it conforms to both fast and frequency-selective channels. Simulation results validate the feasibility of the proposed method in terms of the reliability and real-time capability. In particular, the SSSP scheme shows its advantage in flexibility as it can provide a low error rate and short communication time in various channel conditions.

In this paper, we propose a relaying strategy for single-carrier relay networks with frequency selective channels, where each relay node delays its received signal before amplify-and-forward processing it. We propose a computationally efficient delay design method which reduces the number of delay candidates. To further reduce computational complexity, we develop a simplified delay design method which reduces the number of weight computations. Also, we extend the design method to the case where only partial channel state information of relay-to-destination channels is available. Simulation results show that the proposed relaying strategy outperforms a conventional amplify-and-forward relaying strategy and achieves the performance close to that of a more complex filter-and-forward relaying strategy. It is also shown that the proposed delay design method achieves near-optimum performance.

In data stream analysis, detecting the concept drift accurately is important to maintain the classification performance. Most drift detection methods assume that the class labels become available immediately after a data sample arrives. However, it is unrealistic to attempt to acquire all of the labels when processing the data streams, as labeling costs are high and much time is needed. In this paper, we propose a concept drift detection method under the assumption that there is limited access or no access to class labels. The proposed method detects concept drift on unlabeled data streams based on the class label information which is predicted by a classifier or a virtual classifier. Experimental results on synthetic and real streaming data show that the proposed method is competent to detect the concept drift on unlabeled data stream.

This paper presents a novel 60 GHz-band photonic-integrated array-antenna and module for radio-over-fiber (RoF)-based beam forming. An integrated photonic array-antennas (IPA), where eight photodiodes and 4×2 arrayed patch-antenna are integrated in a single board, is actually fabricated, and 3.5-Gbit/s QPSK digital signal transmission with beam forming of the IPA is experimentally demonstrated. In addition, a novel 60-GHz compact antenna module is proposed and fabricated for increasing the number of antenna elements and flexibility creating various beam patterns. The feasibility of beam forming operation for the proposed antenna module is confirmed by a 60-GHz RoF transmission experiment. The capability of detecting the mobile terminal direction, which is one of the indispensable functions for actual environment, is also studied. The obtained results in this paper will be useful for designing future radio access networks based on RoF transmission technology.

A 42×42-way one-body 2-D beam-switching Butler matrix with waveguide short-slot 2-plane couplers is designed and fabricated in the 22GHz band. The one-body configuration using the commutativity and the overlapping of units allows reducing the size and loss in comparison with a cascade of matrices beam-switching for the horizontal and the vertical planes. It is achieved by replacing 2×2-way 1-plane couplers in the conventional block configuration for a Butler matrix with 22×22-way 2-plane couplers. The measured bandwidth is approximately 2% restricted by the frequency characteristics of the 2-plane couplers. In the radiation from the aperture array antenna of the 42 output ports, the 3.9dB-down coverage of 3-D solid angle by the sixteen beams is around 1.72 steradian which is same as 27.4% of hemisphere at the design frequency for the aperture spacing of 0.73×0.73 wavelength.

Beamforming technology is an effective method to build a robust link. The commonly used digital beamforming is an expensive and power consuming approach to realizing millimeter-wave transmission. This makes radio frequency(RF) beamforming, which has low cost and low power consumption due to its use of phase shifters the more feasible approach to creating stable links in the millimeter-wave band. Unfortunately, the performance of RF processing is degraded by the limited precision of digital phase shifters. In this paper, we analyze the gain loss caused by the limited precision of phase shifter in millimeter wave single stream beam steering. We deduce a theoretical relationship between the array gain loss and variance of phase error. The theoretical results are validated by the Monte Carlo simulations, which indicate that gain loss could be reduced by the increased precision of phase shifter. In practical applications, 4-bit phase shifters provide sufficient accuracy for single stream beam steering.

Communications satellites have been the primary mission from the early period of Japanese space development and their on-board communication equipment are the core devices to realize satellite communications systems. The technologies for this equipment have been developed to meet the requirements of high capacity and high functionality under the severe satellite-imposed constraints. This paper summarizes progress in on-board communication equipment technologies developed and verified by using Engineering Test Satellites and commercial satellites in Japan and describes their prospects.

This paper presents beamforming and beam tracking techniques and downlink performance results from field experiments using a Proof-of-Concept (PoC) system. The PoC implements a 5G mobile radio access system in the millimeter wave band and utilizes beamforming and beam tracking techniques. These techniques are realized with a dielectric lens antenna fed by a switched antenna feeder array. The half-power beamwidth of the antenna is 3° corresponding to massive MIMO using approximately 1000 antenna elements. The system bandwidth is 1GHz and the center frequency is 73.5GHz. Adaptive modulation and coding using four modulation and coding schemes is implemented. The field experiment is conducted in the following small cell environments: a courtyard, a shopping mall and a street canyon. The majority of the test area is Line-Of-Sight (LOS) however the shopping mall course contains 69% Non-LOS (NLOS) conditions. The results show that the maximum throughput of over 2Gbps using rate 7/8 coded 16QAM modulation is achieved in 87%, 34% and 28% of each of the respective environments. The beam tracking achieves high availability of coverage and seamless mobility not only in LOS environments but also under NLOS conditions through the reflected paths.

This paper presents a capacitor-loaded 4x4 planar loop array for three-dimensional near-field beamforming of magnetic resonance wireless power transfer (WPT). This planar loop array provides three important functions: beamforming, selective power transfer, and the ability to work alignment free with the receiver. These functions are realized by adjusting the capacitance of each loop. The optimal capacitance of each loop that corresponds to the three functions can be found using a genetic algorithm (GA); the three functions were verified by comparing simulations and measurements at a frequency of 6.78MHz. Finally, the beamforming mechanism of a near-field loop array was investigated using the relationship between the current magnitude and the resonance frequency of each loop, resulting in the findings that the magnitude and the resonance frequency are correlated. This focused current of the specified loop creates a strong magnetic field in front of that loop, resulting in near-field beamforming.

This paper presents some results of an experimental trial for the 5th generation (5G) wireless communication systems using 28GHz band. In order to tackle rapidly increasing traffic for 2020 and beyond, new radio access networks for the 5G mobile communication systems will introduce the use of higher frequency bands such as spectra higher than 10GHz to achieve higher capacity and super high bit rate transmission of several tens of Gbps. The target of this experimental trial is to evaluate the feasibility of using the 28GHz band with super-wide bandwidth of 800MHz for 5G wireless communication systems. To compensate large path-loss in higher frequency, the beamforming (BF) based on Massive multiple-input multiple-output (MIMO) is one of promising techniques and can be combined with spatial multiplexing of multiple data streams to achieve much higher capacity. In addition, to support the mobility of mobile station (MS), beam tracking technique is important. In this trial, we first conduct a basic experiment of single-stream transmission by using prototype system with base station (BS) having 96-element antenna and MS having 8-element antenna to evaluate the effectiveness of joint transmitter/receiver BF in 28GHz band in terms of coverage, impact of path loss, shadowing loss and penetration loss under indoor, outdoor and outdoor-to-indoor (O-to-I) environments. We show that by using 28 GHz band with BF based on Massive MIMO, higher throughput near 1.2Gbps can be achieved at many points in the indoor environment. It is also shown that the throughput of over 1Gbps can be achieved at points around 200m distant from BS in outdoor line-of-site (LOS) environment. Secondly, to evaluate the effectiveness of spatial multiplexing and beam tracking under more realistic environment, we also conduct the outdoor experiment of BF combined with 2-stream spatial multiplexing in high mobility environment with MS speed of up to 60km/h by using smartphone-shape MS antenna. We also show that maximum throughput of 3.77Gbps can be achieved with MS speed of 60km/h by using BF with 2-stream multiplexing and beam tracking.

This paper explores the potential of orbital angular momentum (OAM) multiplexing as a means to enable high-speed wireless transmission. OAM is a physical property of electro-magnetic waves that are characterized by a helical phase front in the propagation direction. Since the characteristic can be used to create multiple orthogonal channels, wireless transmission using OAM can enhance the wireless transmission rate. Comparisons with other wireless transmission technologies clarify that OAM multiplexing is particularly promising for point-to-point wireless transmission. We also clarify three major issues in OAM multiplexing: beam divergence, mode-dependent performance degradation, and reception (Rx) signal-to-noise-ratio (SNR) reduction. To mitigate mode-dependent performance degradation we first present a simple but practical Rx antenna design method. Exploiting the fact that there are specific location sets with phase differences of 90 or 180 degrees, the method allows each OAM mode to be received at its high SNR region. We also introduce two methods to address the Rx SNR reduction issue by exploiting the property of a Gaussian beam generated by multiple uniform circular arrays and by using a dielectric lens antenna. We confirm the feasibility of OAM multiplexing in a proof of concept experiment at 5.2 GHz. The effectiveness of the proposed Rx antenna design method is validated by computer simulations that use experimentally measured values. The two new Rx SNR enhancement methods are validated by computer simulations using wireless transmission at 60 GHz.

Based on the reconstruction of the augmented interference-plus-noise (IPN) covariance matrix (CM) and the estimation of the desired signal's extended steering vector (SV), we propose a novel robust widely linear (WL) beamforming algorithm. Firstly, an extension of the iterative adaptive approach (IAA) algorithm is employed to acquire the spatial spectrum. Secondly, the IAA spatial spectrum is adopted to reconstruct the augmented signal-plus-noise (SPN) CM and the augmented IPNCM. Thirdly, the extended SV of the desired signal is estimated by using the iterative robust Capon beamformer with adaptive uncertainty level (AU-IRCB). Compared with several representative robust WL beamforming algorithms, simulation results are provided to confirm that the proposed method can achieve a better performance and has a much lower complexity.

Spritz is a stream cipher proposed by Rivest and Schuldt at the rump session of CRYPTO 2014. It is intended to be a replacement of the popular RC4 stream cipher. In this paper we propose distinguishing attacks on the full Spritz, based on a short-term bias in the first two bytes of a keystream and a long-term bias in the first two bytes of every cycle of N keystream bytes, where N is the size of the internal permutation. Our attacks are able to distinguish a keystream of the full Spritz from a random sequence with samples of first two bytes produced by 244.8 multiple key-IV pairs or 260.8 keystream bytes produced by a single key-IV pair. These biases are also useful in the event of plaintext recovery in a broadcast attack. In the second part of the paper, we look at a state recovery attack on Spritz, in a special situation when the cipher enters a class of weak states. We determine the probability of encountering such a state, and demonstrate a state recovery algorithm that betters the 21400 step algorithm of Ankele et al. at Latincrypt 2015. Finally we propose a simple fix that removes the bias in the first two keystream bytes. The countermeasure requires only one additional memory access and hence does not diminish software performance substantially, and in fact the loss in software speed is only around 1.5%.

In this paper, we investigate a novel preamble channel estimation (CE) method based on the compressed sensing (CS) theory in the orthogonal frequency division multiplexing system with offset quadrature amplitude modulation (OQAM/OFDM) over a frequency selective fading channel. Most of the preamble based CE methods waste power by deploying the pilots in all the subcarriers. Inspired by the CS theory, we focus on using many fewer pilots than one of traditional CE methods and realize accurate reconstruction of the channel response. After describing and analyzing the concept of OQAM/OFDM and its traditional CE methods, we propose a novel channel estimation method based on CS that requires fewer pilots in the preamble, and we design the corresponding preamble pattern to meet the requirements of CS. Simulation results validate the efficiency and superior performance of the proposed method in wireless channel.

We propose a microphone array speech enhancement method that integrates spatial-cue-based source power spectral density (PSD) estimation and statistical speech model-based PSD estimation. The goal of this research was to clearly pick up target speech even in noisy environments such as crowded places, factories, and cars running at high speed. Beamforming with post-Wiener filtering is commonly used in many conventional studies on microphone-array noise reduction. For calculating a Wiener filter, speech/noise PSDs are essential, and they are estimated using spatial cues obtained from microphone observations. Assuming that the sound sources are sparse in the temporal-spatial domain, speech/noise PSDs may be estimated accurately. However, PSD estimation errors increase under circumstances beyond this assumption. In this study, we integrated speech models and PSD-estimation-in-beamspace method to correct speech/noise PSD estimation errors. The roughly estimated noise PSD was obtained frame-by-frame by analyzing spatial cues from array observations. By combining noise PSD with the statistical model of clean-speech, the relationships between the PSD of the observed signal and that of the target speech, hereafter called the observation model, could be described without pre-training. By exploiting Bayes' theorem, a Wiener filter is statistically generated from observation models. Experiments conducted to evaluate the proposed method showed that the signal-to-noise ratio and naturalness of the output speech signal were significantly better than that with conventional methods.

HTTP Adaptive Streaming (HAS) has become a popular solution for media delivery over the mobile Internet. However, existing HAS systems are based on the pull-based HTTP/1.1 protocol, leading to high overheads (e.g., in terms of energy, processing, bandwidth) for clients, servers, as well as network nodes. The new HTTP/2 protocol provides a server push feature, which allows the client to receive more than one video segment for each request in order to reduce request-related overheads. In this study, we propose an adaptation method to leverage the push feature of HTTP/2. Our method takes into account not only the request-related overhead but also buffer stability and gradual transitions. The experimental results show that our proposed method performs well under strong throughput variations of mobile networks.