In this paper, we modify the Legendre-Sidelnikov sequence which was defined by M. Su and A. Winterhof and consider its exact autocorrelation values. This new sequence is balanced for any p,q and proved to possess low autocorrelation values in most cases.

RC4 is a widely-used stream cipher, adopted in many standard protocols, such as WEP, WPA and SSL/TLS, as a standard encryption algorithm. Isobe et al. proposed a plaintext recovery attack on RC4 in the broadcast setting, where the same plaintext is encrypted with different secret keys. Their attack is able to recover the first 257bytes by exploiting the biases of the initial bytes of a keystream. In this paper, we propose two types of full plaintext recovery attacks that are able to recover all the bytes, even after the 258th byte, of a plaintext, unlike Isobe et al.'s attack. To achieve this, we combine the use of multiple keystream biases appropriately. The first attack utilizes the initial byte biases and Mantin's long-term bias. This attack can recover the first 1000 terabytes of a plaintext from 234 ciphertexts with a probability of almost one. The second attack is based on two long-term biases. Since this attack does not rely on the biases of the initial bytes of the RC4 keystream, it can recover any byte of a plaintext, even if the initial bytes are disregarded. Given 235 ciphertexts encrypted by different keys, any byte of a target plaintext can be recovered with a probability close to one.

Feedback with carry shift registers (FCSRs) implemented using Galois representation have been found to have a weakness called LFSRization. It leads to powerful attacks against the stream ciphers based on them. A new representation called ring representation has been proposed to avoid the attacks. It was considered to circumvent the weaknesses of Galois FCSRs. This correspondence presents a class of ring FCSRs, which meet the implementation criteria, but are still possible to maintain linear behavior for several clock cycles. Their LFSRization probability and how to improve their security are also mentioned.

We propose a novel phased array-fed dual-reflector antenna that reduces performance degradation caused by multiple reflection. The marked feature of the proposed configuration is that different reflector profiles are employed for the two orthogonal directions. The reflector profile in the beam-scanning section (vertical section) is set to an imaging reflector configuration, while the profile in the orthogonal non-beam-scanning section (horizontal section) is set to a ring-focus Cassegrain antenna configuration. In order to compare the proposed antenna with the conventional antenna in which multiple reflection was problematic, we designed a prototype antenna of the same size, and verified the validity of the proposed antenna. The results of the verification were that the gain in the designed central frequency increased by 0.4 dB, and the ripple of the gain frequency properties that was produced by multiple reflection was decreased by 1.1,dB. These results demonstrated the validity of the proposed antenna.

Although multi-user multiple-input multiple-output (MI-MO) systems provide high data rate transmission, they may suffer from interference. Block diagonalization and eigenbeam-space division multiplexing (E-SDM) can suppress interference. The transmitter needs to determine beamforming weights from channel state information (CSI) to use these techniques. However, MIMO channels change in time-varying environments during the time intervals between when transmission parameters are determined and actual MIMO transmission occurs. The outdated CSI causes interference and seriously degrades the quality of transmission. Channel prediction schemes have been developed to mitigate the effects of outdated CSI. We evaluated the accuracy of prediction of autoregressive (AR)-model-based prediction and Lagrange extrapolation in the presence of channel estimation error. We found that Lagrange extrapolation was easy to implement and that it provided performance comparable to that obtained with the AR-model-based technique.

A two-dimensional (2D) wireless power transmission (WPT) system that handles a wide range of transmitted and received power is proposed and evaluated. A transmitter outputs the power to an arbitrary position on a 2D waveguide sheet by using a beam-forming technique. The 2D waveguide sheet does not require an absorber on its edge. The minimum propagation power on the sheet is increased 18 times by using the beam-forming technique. Power amplifier (PA) efficiency was improved from 19% to 46% when the output power was 10dB smaller than peak power due to the use of a PA supply-voltage and input power control method. Peak PA efficiency was 60%. A receiver inputs a wide range of power levels and drives various load impedances with a parallel rectifier. This rectifier enables a number of rectifying units to be tuned dynamically. The rectifier efficiency was improved 1.5 times while input power range was expanded by 6dB and the load-impedance range was expanded fourfold. The rectifier efficiency was 66-73% over an input power range of 18-36dBm at load impedances of 100 and 400Ω.

In this paper, the spatial smoothing (SS) method is extended to the wideband multipath case. By reordering the array input signal and the weight vector, the corresponding covariance matrix of each subarray can be constructed conveniently. Then, a novel wideband beamforming algorithm, based on the SS method (SS-WB), can be achieved by linearly constrained minimum variance (LCMV). Further improvement of the output signal-to-interference-plus-noise ratio (SINR) for SS-WB can be obtained by removing the desired signal in the observed array data with the reconstruction of covariance matrix, which is denoted as wideband beamformer based on modified SS method (MSS-WB). Both proposed algorithms can reduce the desired signal cancellation due to the super decorrelation ability of SS method and MSS-WB can lead to a significantly improved output SINR. The simulations verify their effectiveness in the multipath environment.

In this paper, we design an Unequal Error Protection (UEP) rateless code with special coding graph and apply it to propose a novel HTTP adaptive streaming based on UEP rateless code (HASUR). Our designed UEP rateless code provides high diversity on decoding probability and priority for data in different important level with overhead smaller than 0.27. By adopting this UEP rateless channel coding and scalable video source coding, our HASUR ensures symbols with basic quality to be decoded first to guarantee fluent playback experience. Besides, it also provides multiple layers to ensure the most suitable quality for fluctuant bandwidth and packet loss rate (PLR) without estimating them in advance. We evaluate our HASUR against the alternative solutions. Simulation results show that HASUR provides higher video quality and more adapts to bandwidth and PLR than other two commercial schemes under End-to-End transmission.

With the advent of high speed links, online flow measurement for, e.g., flow round trip time (RTT), has become difficult due to the enormous demands placed on computational resources. Most existing measurement methods are designed to count the numbers of flows or sizes of flows, but we address the flow RTT measurement, which is an important QoS metric for network management and cannot be measured with existing measurement methods. We first adapt a standard Bloom Filter (BF) for the flow RTT distribution estimation. However, due to the existence of multipath routing and Syn flooding attacks, the standard BF does not perform well. We further design the double-deletion bloom filter (DDBF) scheme, which alleviates potential hash collisions of the standard BF by explicitly deleting used records and implicitly deleting out-of-date records. Because of these double deletion operations, the DDBF accurately estimates the RTT distribution of TCP flows with limited memory space, even with the appearance of multipath routing and Syn flooding attacks. Theoretical analysis indicates that the DDBF scheme achieves a higher accuracy with a constant and smaller amount of memory compared with the standard BF. In addition, we validate our scheme using real traces and demonstrate significant memory-savings without degrading accuracy.

We propose a new algorithm to suppress both stationary background noise and nonstationary directional interference noise in a speech enhancement system that employs the generalized sidelobe canceller. Our approach builds on advances in generalized sidelobe canceller design involving the transfer function ratio. Our system is composed of three stages. The first stage estimates the transfer function ratio on the acoustic path, from the nonstationary directional interference noise source to the microphones, and the powers of the stationary background noise components. Secondly, the estimated powers of the stationary background noise components are used to execute spectral subtraction with respect to input signals. Finally, the estimated transfer function ratio is used for speech enhancement on the primary channel, and an adaptive filter reduces the residual correlated noise components of the signal. These algorithmic improvements give consistently better performance than the transfer function generalized sidelobe canceller when input signal-to-noise ratio is 10 dB or lower.

A directional array radiator is presented, the aim of which is to enhance the sound of the television in a particular direction and hence provide a volume boost to improve speech intelligibility for the hard of hearing. The sound radiated by the array in other directions is kept low, so as not to increase the reverberant level of sound in the listening room. The array uses 32 loudspeakers, each of which are in phase-shift enclosures to generate hypercardioid directivity, which reduces the radiation from the back of the array. The loudspeakers are arranged in 8 sets of 4 loudspeakers, each set being driven by the same signal and stacked vertically, to improve the directivity in this plane. This creates a 3D beamformer that only needs 8 digital filters to be made superdirective. The performance is assessed by means of simulations and measurements in anechoic and reverberant environments. The results show how the array obtains a high directivity in a reverberant environment.

Earlier attempts to deploy two units of parametric loudspeakers have shown encouraging results in improving the accuracy of spatial audio reproductions. As compared to a pair of conventional loudspeakers, this improvement is mainly a result of being free of crosstalk due to the sharp directivity of the parametric loudspeaker. By replacing the normal parametric loudspeaker with the steerable parametric loudspeaker, a flexible sweet spot can be created that tolerates head movements of the listener. However, spatial aliasing effects of the primary frequency waves are always observed in the steerable parametric loudspeaker. We are motivated to make use of the spatial aliasing effects to create two sound beams from one unit of the steerable parametric loudspeaker. Hence, a reduction of power consumption and physical size can be achieved by cutting down the number of loudspeakers used in an audio system. By introducing a new parameter, namely the relative steering angle, we propose a stereophonic beamsteering method that can control the amplitude difference corresponding to the interaural level difference (ILD) between two sound beams. Currently, this proposed method does not support the reproduction of interaural time differences (ITD).

This paper proposes a sound source orientation estimation method that is suitable for a distributed microphone arrangement. The proposed method is based on orientation-extended beamforming (OEBF), which has four features: (a) robustness against reverberations, (b) robustness against noises, (c) free arrangements of microphones and (d) feasibility for real-time processing. In terms of (a) and (c), since OEBF is based on a general propagation model using transfer functions (TFs) that include all propagation phenomena such as reflections and diffractions, OEBF causes no model errors for the propagation phenomena, and is applicable to arbitrary microphone arrangements. Regarding (b), OEBF overcomes noise effects by incorporating three additional processes (Amplitude extraction, time-frequency mask and histogram integration) that are also proposed in this paper. As for (d), OEBF is executable in real-time basis as the execution process is the same as usual beamforming processes. A numerical experiment was performed to confirm the theoretical validity of OEBF. The results showed that OEBF was able to estimate sound source positions and orientations very precisely. Practical experiments were carried out using a 96-channel microphone array in real environments. The results indicated that OEBF worked properly even under reverberant and noisy environments and the averaged estimation error was given only 4°.

This paper studies an underlay-based cognitive two-way relay network which consists of a primary network (PN) and a secondary network (SN). Two secondary users (SUs) exchange information with the aid of multiple single-antenna amplify-and-forward relays while a primary transmitter communicates with a primary receiver in the same spectrum. Unlike the existing contributions, the transmit powers of the SUs and the distributed beamforming weights of the relays are jointly optimized to minimize the sum interference power from the SN to the PN under the quality-of-service (QoS) constraints of the SUs determined by their output signal-to-interference-plus-noise ratio (SINR) and the transmit power constraints of the SUs and relays. This approach leads to a non-convex optimization problem which is computationally intractable in general. We first investigate two necessary conditions that optimal solutions should satisfy. Then, the non-convex minimization problem is solved analytically based on the obtained conditions for single-relay scenarios. For multi-relay scenarios, an iterative numerical algorithm is proposed to find suboptimal solutions with low computational complexity. It is shown that starting with an arbitrarily initial feasible point, the limit point of the solution sequence derived from the iterative algorithm satisfies the two necessary conditions. To apply this algorithm, two approaches are developed to find an initial feasible point. Finally, simulation results show that on average, the proposed low-complexity solution considerably outperforms the scheme without source power control and performs close to the optimal solution obtained by a grid search technique which has prohibitively high computational complexity.

In this paper, we analyze the performance of a dual-hop multiuser amplify-and-forward (AF) relay network with the effect of the feedback delay, where the source and each of the K destinations are equipped with Nt and Nr antennas respectively, and the relay is equipped with a single antenna. In the relay network, multi-antenna and multiuser diversities are guaranteed via beamforming and opportunistic scheduling, respectively. To examine the impact of delayed feedback, the new exact analytical expressions for the outage probability (OP) and symbol error rate (SER) are derived in closed-form over Rayleigh fading channel, which are useful for a large number of modulation schemes. In addition, we present the asymptotic expressions for OP and SER in the high signal-to-noise ratio (SNR) regime, from which we gain an insight into the system performance with deriving the diversity order and array gain. Moreover, based on the asymptotic expressions, we determine power allocation among the network nodes such that the OP is minimized. The analytical expressions are validated by Monte-Carlo simulations.

To improve throughput of Electron Beam Direct Writing (EBDW) with Character Projection (CP) method, a structured routing architecture (SRA) has been proposed to restrict VIA placement and wire-track transition. It reduces possible layout patterns in the interconnect layers, and increases VIA and metal figure numbers in the EB shots while suppressing the CP character number explosion. In this paper, we discuss details of the SRA design methodology, and demonstrate the CP performance by SRA in comparison with other EBDW techniques. Our experimental results show viable CP performance for practical use, and prove SRA's feasibility in 14nm mass fabrication.

This letter considers the weighted sum-rate maximization (WSRMax) problem in downlink multicell multiuser orthogonal frequency-division multiplexing system. The WSRMax problem under per base station transmit power constraint is known to be NP-hard, and the optimal solution is computationally very expensive. We propose two less-complex suboptimal convex approximated solutions which are based on sequential parametric convex approximation approach. We derive provably faster convergent iterative convex approximation techniques that locally optimize the weighted sum-rate function. Both the iterative solutions are found to converge to the local optimal solution within a few iterations compared to other well-known techniques. The numerical results demonstrate the effectiveness and superiority of the proposed approaches.

An integrated 2×28Gb/s dual-channel duobinary driver IC is presented. Each channel has integrated coding blocks, transforming a non-return-to-zero input signal into a 3-level electrical duobinary signal to achieve an optical duobinary modulation. To the best of our knowledge this is the fastest modulator driver including on-chip duobinary encoding and precoding. Moreover, it only consumes 652mW per channel at a differential output swing of 6Vpp.

Recent progress in research on the finite element method (FEM) for optical waveguide design and analysis is reviewed, focusing on the author's works. After briefly reviewing fundamentals of FEM such as a theoretical framework, a conventional nodal element, a newly developed edge element to eliminate nonphysical, spurious solutions, and a perfectly matched layer to avoid undesirable reflections from computational window edges, various FEM techniques for a guided-mode analysis, a beam propagation analysis, and a waveguide discontinuity analysis are described. Some design examples are introduced, including current research activities on multi-core fibers.

The recently suggested regular-type triangular quadrature amplitude modulation (TQAM) provides considerable power gain over square quadrature amplitude modulation (SQAM) at the expense of a slight increase in detection complexity. However, the power gain of the TQAM is limited due to the constraint that signal points should be regularly located at the vertexes of contiguous equilateral triangles. In this paper, we investigate two irregular (optimum and suboptimum) TQAMs where signal points are irregularly distributed while preserving the equilateral triangular lattice, and calculate achievable power gains of the proposed constellations. We also address optimum and suboptimum bit stream mapping methods and suggest a simple and optimum detection method for the constellations to be meaningful in practical implementation, and present analytical and simulation results. The proposed constellations can provide the asymptotic power gains of 0.825dB and 0.245dB over SQAM and regular TQAM, respectively.