This paper presents a comparison of hierarchical and non-hierarchical synchronization channel (SCH) structures in terms of the initial cell search time and neighboring cell search time in order to establish the optimum SCH structure in the Evolved UTRA downlink. Computer simulation results show that in a 19-cell configuration, the cell search time at 90% in the cumulative distribution function (CDF) using the hierarchical SCH structure is less than half that using the non-hierarchical SCH structure in a neighboring cell search under low signal-to-interference plus noise power ratio (SINR) conditions, although both structures achieve almost the same cell search time in the initial cell search. This is due to the cross-correlation based SCH symbol timing detection in the hierarchical SCH structure, which is affected less by noise than the auto-correlation based detection in the non-hierarchical SCH structure. Thus, we conclude that the hierarchical SCH structure is superior to the non-hierarchical SCH structure based on the cell search time performance especially in the neighboring cell search.

This paper compares the turbo code and rate-compatible low-density parity-check (LDPC) codes based on the block error rate (BLER) performance and decoding complexity in order to clarify which channel coding scheme is most appropriate for the channel coding scheme in the OFDM based Evolved UTRA (E-UTRA) downlink. Simulation results and the decoding complexity analysis show that although the Rate-Compatible/Quasi-Cyclic (RC/QC)-LDPC code employing an offset layered belief propagation (BP) method can reduce the computational complexity by approximately 30% for the channel coding rate of R ≥ 1/2, the required average received signal energy per bit-to-noise power spectrum density ratio (Eb/N0) is degraded by approximately 0.2-0.3 dB for R = 1/3, 1/2 and 3/4 compared to that for the turbo code. Moreover, the decoding complexity level of the RC/QC-LDPC code with the δ-min algorithm is almost the same or higher than that for the turbo code with a slight degradation in the required received Eb/N0. Although the decoding complexity level of the ZigZag code is lower than that of the turbo code, the code brings about a distinct loss in the required average received Eb/N0 of approximately 0.4 dB. Finally, the turbo Single Parity Check (SPC) code improves the BLER performance compared to the ZigZag code, i.e., achieves almost the same BLER performance as that for the turbo code, at the cost of a two-fold increase in the decoding complexity. As a result, we conclude that the turbo code with a contention free interleaver is more promising than the LDPC codes for prioritizing the achievable performance over complexity and as the channel coding scheme for the shared data channel in the E-UTRA.

A new in vitro experimental tool was developed to study the mechanism of the ultrasonic closing clicks' genesis of mechanical heart valves. Since the newly developed tester adopted compressed air flow directly instead of the blood analog fluid to drive the mechanical heart valve, it is not possibe to generate any cavitation. Closing clicks were measured with a small accelerometer at the surface of the valve holder made of silicone rubber. Ultrasonic closing clicks as well as audible closing clicks, similar to those measured clinically, could be observed using this setup. Thus, it was confirmed that the ultrasonic closing clicks can be generated without the existence of cavitation. Simultaneous measurements of the valve motion were made with a high-speed video camera, and the analysis of the video frames and clicks showed that higher frequency signal components of more than 50 kHz could be generated only at the instant of the closure, which means the collision of the occluder with the housing. Eighteen miniature accelerometers with an area of one square millimeter were developed and stuck on the housing to monitor the distribution of the housing vibrations in detail, and it was found that the vibrations correspond to the ultrasonic closing clicks propagated from the valve stop: the collision point of the occluder with the housing. This fact indicated that the generation of ultrasonic closing clicks are limited to the small area of the collision. From those results, it was concluded that the major origin of the ultrasonic closing clicks' genesis should be the collision of the occluder with the housing.

A general-purpose multi-Gbps LVDS driver is presented with a new distortion-free level conversion scheme. For high-speed transmission, a dynamic pre-emphasis scheme is also proposed with overdriving current effectively distributed in time. The proposed LVDS driver achieves supply-insensitive duty preservation with a reduction of switching noise by 50-percent.

The Green's function of free space for the fast inhomogeneous plane wave algorithm is represented by an integration in the complex plane. The error in the computational process is determined by the number of sampling points, the truncation of the integration path, and the extrapolation. Therefore, the error control method is different from that for the fast multipole method. We will discuss the worst-case interactions of the fast inhomogeneous plane wave algorithm for the box implementation and define the upper and lower bounds of the computational error.

We report effects of washing rubbed polyimide film on the near surface. Especially we focused dependence of solvent. Rubbed polyimide films have been used as liquid crystal alignment films in Liquid crystal displays (LCDs), and in actual LCD panel fabrication washing on film surfaces after rubbing is essential process to remove dust and pollution. We investigated the effects of washing by grazing incidence X-ray diffraction (GIXD) measurements. In GIXD, the X-ray penetration into the polymer was changed from 8 nm (suface sensitive) to 4 nm (bulk sensitive) by variation of the X-ray incidence angle. It was found that crystallization near the surface induced by soaking was considerably dependent on solvent. However, in-plane distribution of the surface polymer chains of polyimide film was not found to be dependent on the solvents.

3GPP evolved packet system (EPS) is an all-IP based system that supports various access networks such as LTE, HSPA/HSPA+ and non-3GPP networks. Recently, the support of IP flows with packet level QoS profiles has been added to the requirements of the EPS. This paper proposes an adaptive modulation and coding (AMC) scheme that supports the QoS of such IP flows in the 3G LTE access network of the EPS. Defining the retransmission as a critical factor for QoS, the proposed scheme applies different maximum packet error probability Pmax to each packet when selecting the AMC transmission mode. In determining Pmax, the QoS constraints as well as channel condition are considered, balancing two objectives: the satisfaction of the QoS and the maximization of spectral efficiency. Simulations show that it is able to reduce both delay violation and retransmission, while improving throughput in comparison with an existing scheme.

In the Evolved UTRA (UMTS Terrestrial Radio Access) uplink, single-carrier frequency division multiple access (SC-FDMA) radio access was adopted owing to its advantageous low peak-to-average power ratio (PAPR) feature, which leads to wide coverage area provisioning with limited peak transmission power of user equipments. This paper proposes orthogonal pilot channel generation using the combination of FDMA and CDMA in the SC-FDMA-based Evolved UTRA uplink. In the proposed method, we employ distributed FDMA transmission for simultaneous accessing users with different transmission bandwidths, and employ CDMA transmission for simultaneous accessing users with identical transmission bandwidth. Moreover, we apply a code sequence with a good auto-correlation property such as a Constant Amplitude Zero Auto-Correlation (CAZAC) sequence employing a cyclic shift to increase the number of sequences. Simulation results show that the average packet error rate performance using an orthogonal pilot channel with the combination of FDMA and CDMA in a six-user environment, i.e., four users each with a 1.25-MHz transmission bandwidth and two users each with a 5-MHz transmission bandwidth, employing turbo coding with the coding rate of R = 1/2 and QPSK and 16QAM data modulation coincides well with that in a single-user environment with the same transmission bandwidth. We show that the proposed orthogonal pilot channel structure using the combination of distributed FDMA and CDMA transmissions and the application of the CAZAC sequence is effective in the SC-FDMA-based Evolved UTRA uplink.

We present a TCP flow level performance evaluation on error rate aware scheduling algorithms in Evolved UTRA and UTRAN networks. With the introduction of the error rate, which is the probability of transmission failure under a given wireless condition and the instantaneous transmission rate, the transmission efficiency can be improved without sacrificing the balance between system performance and user fairness. The performance comparison with and without error rate awareness is carried out dependant on various TCP traffic models, user channel conditions, schedulers with different fairness constraints, and automatic repeat request (ARQ) types. The results indicate that error rate awareness can make the resource allocation more reasonable and effectively improve the system and individual performance, especially for poor channel condition users.

Shot transition detection is a core technology in video browsing, indexing systems and information retrieval. In this paper we propose a dissolve detection algorithm using the characteristics of edge in MPEG compressed video. Using the intensity change information of edge pixels obtained by Sobel edge detector, we detect the location of a dissolve and its precise duration. We also present a new reliable method to eliminate the false dissolves. The proposed algorithm is tested in various types of videos, and the experimental results show that the proposed algorithm is effective and robust.

This paper proposes a dual-level low voltage differential signaling (DLVDS) circuit aimed at low power consumption and reducing transmission lines for LCD driver IC's. We apply two-bit binary data to the DLVDS circuit as inputs, and then the circuit converts these two inputs into two kinds of fully differential signal levels. In the DLVDS circuit, two transmission lines are sufficient to transfer two-bit binary inputs while keeping the conventional LVDS features. The receiver recovers the original two-bit binary data through a level decoding circuit. The proposed circuit was fabricated using a commercial 0.25 µm CMOS technology. Under a 2.5 V supply voltage, the circuit shows a data rate of 1-Gbps/2-line and power consumption of 35 mW.

This paper proposes physical channel structures and a cell search method for OFDM based radio access in the Evolved UTRA (UMTS Terrestrial Radio Access) downlink, which supports multiple scalable transmission bandwidths from 1.25 to 20 MHz. In the proposed physical channel structures, the central sub-carrier of the OFDM signal is located on the frequency satisfying the 200-kHz raster condition regardless of the transmission bandwidth of the cell site. Moreover, the synchronization channel (SCH) and broadcast channel (BCH), which are necessary for cell search, are transmitted in the central part of the entire transmission spectrum with a fixed bandwidth. In the proposed cell search method, a user equipment (UE) acquires the target cell in the cell search process in the initial or connected mode employing the SCH and possibly the reference signal, which are transmitted in the central part of the given transmission bandwidth. After detecting the target cell, the UE decodes the common control information through the BCH, which is transmitted at the same frequency as the SCH, and identifies the transmission bandwidth of the cell to be connected. Computer simulations show the fast cell search performance made possible by using the proposed SCH structure and the cell search method.

We focus our attention on the layout dependent Across Chip Linewidth Variability (ACLV) of gate-forming poly-silicon patterns as a measure for manufacturability, which is a major contributor of systematic gate-length variation. First, we study the ACLV of standard cell layouts by lithography simulation. Then, we introduce regularity in gate-forming poly-silicon patterns and how it improves the ACLV and also how it incurs area-overhead. According to the investigation, we propose two design guidelines for standard-cell layout that can reduce ACLV with reasonable area overhead. Those guidelines include on-grid fixed-pitch layout with dummy-poly insertion and stretched gate-poly extension. Design experiments assuming a 65 nm process technology indicate that a D-FF designed with the first guideline reduces ACLV by 35% with 14% area overhead and the second guideline reduces ACLV by 75% with 29% area overhead at the best focus condition. Under defocus conditions, both layouts exhibit stable characteristics whereas the variability of conventional layout grows rapidly as the level of defocus increases. Circuit-level lithography simulation over benchmark circuits also supports that the proposed guidelines considerably reduces the amount of gate length variation.

This paper describes a morpheme-based pronunciation model that is especially useful to develop the pronunciation lexicon for Large Vocabulary Continuous Speech Recognition (LVCSR) in Korean. To address pronunciation variation in Korean, we analyze phonological rules based on phonemic contexts together with morphological category and morpheme boundary information. Since the same phoneme sequences can be pronounced in different ways at across morpheme boundary, incorporating morphological environment is required to manipulate pronunciation variation modeling. We implement a rule-based pronunciation variants generator to produce a pronunciation lexicon with context-dependent multiple variants. At the lexical level, we apply an explicit modeling of pronunciation variation to add pronunciation variants at across morphemes as well as within morpheme into the pronunciation lexicon. At the acoustic level, we train the phone models with re-labeled transcriptions through forced alignment using context-dependent pronunciation lexicon. The proposed pronunciation lexicon offers the potential benefit for both training and decoding of a LVCSR system. Subsequently, we perform the speech recognition experiment on read speech task with 34K-morpheme vocabulary. Experiment confirms that improved performance is achieved by pronunciation variation modeling based on morpho-phonological analysis.

Electromechanical switching devices such as relays may be surprisingly forgiving to occasional, but temporary, electrical stress beyond specification. Consequently delayed openings due to welded contacts on the order of milliseconds usually have been unnoticed and hence have not been reason for concern. However, as electrical systems of vehicles are getting "smarter" and more and more diagnostic routines are being implemented, even such short delay times may be translated as errors. Pre-conditioning contact surfaces has been explored as a measure to increase the welding resistance and eliminate contact opening delays. The 20-A-class relay investigated has been optimized to break occasional current peaks up to 80 ADC.

In this paper, a method of separating the effects of the thermal diffusivity, durations and integral powers of the bridge and arc on the temperature rise of AgPd contacts was proposed. First, the effects of the Pd content on the durations and integral powers of the bridge and arc, and the temperature rise of the contacts were discussed. Because the integral power of bridge was larger than that of the arc under our experimental conditions of 40 V open-circuit, 5 A close-circuit and 100 µm/s opening velocity, the temperature rise of the contacts was dominated by the bridge. No remarked difference in bridge duration can be seen among the six materials. Although the integral power of the bridge in the case of Pd was maximum, the maximum temperature rise of the contact was observed in the case of AgPd60. To clarify the contribution of each factor, the effect of thermal diffusivity on the temperature rise of the contact was evaluated by the finite-difference time-domain (FDTD) method. In the case of Pd, because its thermal diffusivity was largest, heat diffused rapidly. On the other hand, the thermal diffusivity in the case of AgPd60 was small, and heat diffused slowly to the holders. The maximum temperature rise was observed in the case of AgPd60. It was demonstrated that the proposed method of separating the effects of thermal diffusivity, durations and integral powers of the bridge and arc on the temperature rise of contacts is effective in enabling us to understand contact phenomena.

In this paper, we introduce a new decision problem associated with lattices, named the Exact Length Vector Problem (ELVP), and prove the NP-completeness of ELVP in the ∞ norm. Moreover, we define two variants of ELVP. The one is a binary variant of ELVP, named the Binary Exact Length Vector Problem (BELVP), and is shown to be NP-complete in any p norm (1 ≤ p ≤ ∞). The other is a nonnegative variant of ELVP, named the Nonnegative Exact Length Vector Problem (NELVP). NELVP is defined in the 1 norm, and is also shown to be NP-complete.

We developed an olfactory display to blend 8 component odors at any composition. The solenoid valves controlled by an algorithm with delta sigma modulation showed the sufficient capability. Then, we developed a system for presenting a movie together with scents. We actually made a movie with scents and evaluated it using questionnaire survey. It was found that the scene with smell attracted the experimental subjects' attention and, moreover, the contrast of the pleasant smell with the offensive one emphasized their attention. Furthermore, we established several guidelines for producing movies with scents.

An optically scanning electromagnetic field probe system consisting of an electro-optic or magneto-optic crystal and a galvano scanner is proposed for high-speed electromagnetic field distribution measurements. We used this technique to measure electromagnetic field distributions near printed circuit boards or ICs to address electromagnetic compatibility problems or in designing electronic devices. With our scanning system, we can measure the electric field intensities of about 40,000 points with an area of 4040 mm in about 3 minutes (4 ms per point) up to 2.7 GHz. We measured the electric near-field distribution above a five-split transmission line using a cadmium telluride (CdTe) electro-optic crystal. The measurement results showed that the spatial resolution of the system was less than 400 µm in the case of a common current with a crystal thickness of 1 mm. The electric near-field distribution above a microstrip line filter was measured using LiNbO3 electro-optic crystal. Changes in the distribution according to the frequency were observed. The experimental results obtained using this system were compared with simulation results obtained using a finite-difference time-domain method. The overall results indicated that the measurement system is capable of accurately measuring electric near-fields. We also discuss the invasiveness of the measurement system, due to the electro-optic crystals, in terms of both the experimental and simulated results.

The Gallant-Lambert-Vanstone method [14](GLV method for short) is a scalar multiplication method for elliptic curve cryptography (ECC). In WAP WTLS [49], SEC 2 [44], ANSI X9.62 [1] and X9.63 [2], several domain parameters for applications of the GLV method are described. Curves with those parameters have efficiently-computable endomorphisms. Recently the GLV method for Jacobians of hyperelliptic curve (HEC) has also been studied. In this paper, we discuss applications of the GLV method to curves with real multiplication (RM). It is the first time to use RM for efficient scalar multiplication as far as we know. We describe the general algorithm for using such RM, and we show that some genus 2 curves with RM have enough effciency to be used in the GLV method as in the previous CM case. Moreover, we will see that such RM curves can be obtained abundantly unlike the previously proposed CM curves of genus 2.