In information-spectrum methods proposed by Han and Verdu, quantities defined by using the limit superior (or inferior) in probability play crucial roles in many problems in information theory. In this paper, we introduce two nonconventional quantities defined in probabilistic ways. After clarifying basic properties of these quantities, we show that the two quantities have operational meaning in the ε-coding problem of a general source in the ordinary and optimistic senses. The two quantities can be used not only for obtaining variations of the strong converse theorem but also establishing upper and lower bounds on the width of the entropy-spectrum. We also show that the two quantities are expressed in terms of the smooth Renyi entropy of order zero.

In order to detect snow and ice on a road surface, the microwave measurement method of dielectric constants are presented. And some examples of measurements for artificial and natural snow and ice using the method are introduced. The results show reasonable estimations of the dielectric constants, and they indicate that the method could be utilized for the snow and ice detection.

This letter considers a sum-rate maximization problem with user scheduling wherein each user has a minimum-rate requirement in multiple-input-multiple-output broadcast channel. The multiuser strategy used in the user scheduling is a joint transceiver scheme with block diagonal geometric mean decomposition. Since optimum solution to the user scheduling problem generally requires exhaustive search, we propose a suboptimum user scheduling algorithm with each user's minimum-rate requirement as the main constraint. In order to satisfy maximum sum-rate and minimum-rate constraints simultaneously, we additionally consider power allocation for scheduled users. Simulation results show that the proposed user scheduling algorithm, together with the user power allocation, achieves sum-rate close to the exhaustive search, while also guarantees minimum-rate requirement of each user.

A monopulse angle measurement method is often utilized to measure a target angle. However, this method cannot measure correct angles for multiple targets which cannot be distinguished by range, Doppler frequency and beamwidth. When the number of targets which cannot be distinguished by these parameters is restricted to two, a method which can measure two targets angles has been proposed. However, an approximation is utilized with this method, so that measured angles have errors even though the signal-to-noise ratio is infinite. Another method which can simultaneously measure azimuths and elevations for only two targets has also been proposed. However, this conventional method requires four receivers, and is therefore difficult to apply when there is a hard ware limitation. In this paper, we propose a method to measure azimuths and elevations of two targets by using two receivers and a time division system. A pairing problem has occurred due to the time division angle measurement with this method, so we also propose an algorithm to solve this pairing problem. We finally verify the proposed method by a numerical simulation and experimentation. The results show that the angles of two targets can be measured by our proposed method by using two receivers.

Source coding theorem reveals the minimum achievable code length under the condition that the error probability is smaller than or equal to some small constant. In the single user communication system, the source coding theorem was proved for general sources. The class of general source is quite large and it is important result since the result can be applied for a wide class of sources. On the other hand there are several studies to evaluate the achievable code length more precisely for the restricted class of sources by using the restriction. In the multi-user communication system, although the source coding theorem was proved for general correlated sources, there is no study to evaluate the achievable code length more precisely. In this study, we consider the stationary memoryless correlated sources and show the coding theorem for Slepian-Wolf type problem more precisely than the previous result.

To reduce laborious tasks of the phase determination, our previous paper has proposed a method to derive phase reference for two-tone intermodulation distortion (IMD) measurement of a power amplifier (PA) by using small-signal S-parameters. Since the method is applicable to low output power level, this paper proposes an iterative process to extend the applicable power level up to 1-dB compression. The iterative process is based on extraction of linear response: the principle of the extraction is described theoretically by using an accurate model of the PA with memory effect. Measurement of two-tone IMD is made for a GaN FET PA. Validity of the iteration is confirmed as convergence of the extracted linear response to that given by the product of S21 and input signal. Measured results also show validity of the physical model of the memory effect provided by Vuolevi et al. because beat frequency dependences of IMD's are accurately fitted by bias impedances at even order harmonics of envelope frequency. The PA is characterized by using measured results and the third and fifth order inverses of the PA are designed. Improvement of IMD is theoretically confirmed by using the inverses as predistorters.

A 100 GHz grooved circular empty cavity is proposed for the low loss dielectric substrate measurements by the cut-off circular waveguide method in W band. The influence of the excitation holes for the coaxial cable with a small loop are revealed by an FEM based 3D electromagnetic simulator. And also, the diameter of the excitation hole is determined based on the calculated results and the manufacturing accuracy. Then, two kinds of four 100 GHz grooved circular empty cavities are fabricated. Comparative experiments of the cavities with the different excitation holes validate the simulated results. Moreover, the complex permittivity of a PTFE plate is measured using the fabricated four cavities by the cut-off circular waveguide method around 84 GHz. The measured results agree within measurement error about 0.5% for εr and 5% for tanδ. Also, these results accord with results measured by the Whispering-Gallery mode resonator method in 85–110 GHz band. It verifies that the proposed 100 GHz cavity for the cut-off waveguide method is useful for the complex permittivity measurement of low loss dielectric substrates in W band.

The waveguide-penetration method is a method to measure the electrical properties of materials. In this method, a cylindrical object pierces a rectangular waveguide through a pair of holes at the centre of its broad walls. Then, the complex permittivity and permeability of the object are estimated from measured S-parameters after TRL calibration. This paper proposes a new calibration algorithm for the waveguide-penetration method. Reference materials with known electrical properties are fabricated in cylindrical shapes to fit into the holes in the waveguide and are used as calibration standards. The algorithm is formulated using the property of equal traces in similar matrices, and we show that at least two reference materials are needed to calibrate the system. The proposed algorithm yields a simpler means of calibration compared to TRL and is verified using measurements in the S-band. Also, the error sensitivity coefficients are derived. These coefficients give valuable information for the selection of reference materials.

A thin electromagnetic band-gap (EBG) absorber is employed to capture the 2-d image of radio-frequency (RF) power distribution. The EBG absorber consists of an array of mushroom unit cells formed on a thin dielectric substrate with a metal backplane, and lumped resistors interconnecting the surface patches of the mushrooms. Around the resonance frequency at which the EBG structure acts as a high-impedance surface, the RF power incident on the surface is absorbed by the lumped resistors which are matched with the incident wave impedance. By detecting directly the amounts of power consumed by the individual resistors, an “RF power imager” can be constructed which captures the 2-d distribution of the RF power illuminating the EBG surface, where polarization discrimination is possible. The resonance (i.e., absorption) frequency is made tunable by adding varactor diodes in parallel with the lumped resistors. The EBG absorber tunable in the frequency range of 700 MHz–2.7 GHz is designed and fabricated, and its performance is evaluated by an equivalent-circuit analysis, simulation and measurement. It is shown that the small resistance of the varactors have a considerable effect on the absorption performance. RF power distributions radiated from a dipole antenna are successfully measured by a matrix of sensitive power detectors installed on the backside of the absorber. Using such an RF power imager, the power distributions of even impulsive RF signals and/or noises can be captured and visualized in situ and in real-time, while the electromagnetic environment is almost undisturbed by the EBG absorber.

A new speed enhancement technique for pulsed laser rangefinders based on Lagrange's theorem in group theory using an undersampling method has been developed. In the undersampling method, frequency conversion for high-resolution ranging and digitizing are conducted by sampling a reference frequency signal at the timings of the reception of pulsed light from the target. In the present work, the rangefinder generates different sampling intervals of the reference frequency signal: different numbers of sampling points within the period of a reference signal, over a wide range. This is accomplished by slightly changing the period of the pulsed light emitted, without changing the synthesizer frequency which generates the period. This technique requires a minimum of additional hardware. In this paper, we describe the detail of the selection of the number of sampling points based on Lagrange's theorem. And we demonstrate a possibility of expanding the sampling interval to the point where an aliasing of the harmonic components of the reference signal occurs by simulations that focus on the calculation of the phase of the fundamental frequency of the reference signal. And we report on the results of rangefinder experiments for a reduction in the number of the sampling points. We have achieved a 10-fold enhancement of speed by selecting 10 sampling points over the results from the previous studies that had 100 sampling points within a period of a reference signal. And we have confirmed that the reduction in sampling points has a very little influence on the linearity, which is an acceptable trade-off for achieving the speed enhancement. This technique, based on Lagrange's theorem in group theory, allows us to control the minimum number of samplings required to calculate distances, so that high-speed data acquisition for coarse measurements and normal-speed data acquisition for fine measurements become selectable. Such a system with high flexibility in measurement modes has been developed.

Distance to target is fundamental and very important information in numerous engineering fields. Many distance measurement methods using sound use the time delay of a reflected wave, which is measured in reference to the transmitted wave. This method, however, cannot measure short distances because the transmitted wave, which has not attenuated sufficiently by the time the reflected waves are received, suppresses the reflected waves for short distances. Therefore, we proposed an acoustic distance measurement method based on the interference between the transmitted wave and the reflected waves, which can measure distance in a short range. The proposed method requires a cancellation processing for background components due to the spectrum of the transmitted wave and the transfer function of the measurement system in real environments. We refer to this processing as background components cancellation processing (BGCCP). We proposed BGCCP based on subtraction or whitening. However, the proposed method had a limitation with respect to the transmitted wave or additive noise in real environments. In the present paper, we propose an acoustic distance measurement method based on the new BGCCP. In the new BGCCP, we use the calibration of a real measurement system and the whitening processing of the transmitted wave and introduce the concept of the cepstrum to the proposed method in order to achieve robustness. Although the conventional BGCCP requires the recording of the transmitted wave under the condition without targets, the new BGCCP does not have this requirement. Finally, we confirmed the effectiveness of the proposed method through experiments in real environments. As a result, the proposed method was confirmed to be valid and effective, even in noisy environments.

This paper proposes a new resource allocation algorithm for uplink OFDMA-based cooperative relay networks, assuming multiple user nodes, multiple relay nodes and a single destination. The aim is to maximise the total sum of the users' data rates, while guaranteeing fairness among them with different QoS requirements. Assuming perfect channel state information (CSI) at the resource allocation controller, the optimisation problem is formulated such that each user is assigned a weight factor based on its QoS requirements. The ones with higher weights are given higher priorities to select their resources (relay stations and subcarriers) first. Once the required QoS is achieved for all users, the weight factor for all users is reduced to a small uniform value. The remaining resources are then allocated to the users with higher instantaneous rates in order of magnitude. The results show that the proposed algorithm outperforms the greedy and static algorithms in terms of outage probability and fairness, and at the same time outperforms Jeong's algorithm by 58% in terms of total sum rate, with an average 74% reduction in system complexity.

The development of the electricity market enables us to provide electricity of varied quality and price in order to fulfill power consumers' needs. Such customers choices should influence the process of adjusting power generation and spinning reserve, and, as a result, change the structure of a unit commitment optimization problem (UCP). To build a unit commitment model that considers customer choices, we employ fuzzy variables in this study to better characterize customer requirements and forecasted future power loads. To measure system reliability and determine the schedule of real power generation and spinning reserve, fuzzy Value-at-Risk (VaR) is utilized in building the model, which evaluates the peak values of power demands under given confidence levels. Based on the information obtained using fuzzy VaR, we proposed a heuristic algorithm called local convergence-averse binary particle swarm optimization (LCA-PSO) to solve the UCP. The proposed model and algorithm are used to analyze several test systems. Comparisons between the proposed algorithm and the conventional approaches show that the LCA-PSO performs better in finding the optimal solutions.

P. Kirchberger proved that, for a finite subset X of Rd such that each point in X is painted with one of two colors, if every d+2 or fewer points in X can be separated along the colors, then all the points in X can be separated along the colors. In this paper, we show a more colorful theorem.

In this letter, we consider a control problem of a chain of integrators with a delay in the input under measurement feedback. While there are several control results for our considered system, they have not dealt with any of measurement feedback problems. Our proposed controller is coupled with a low-pass filter such that it can attenuate the sensor noise effect and reduce the ultimate bounds of the controlled systems states. Our result shows that the proposed method has clear benefit over the existing results.

In this paper, a new algorithm called TGA is introduced which defines the concept of time more naturally for the first time. A parameter called TimeToLive is considered for each chromosome, which is a time duration in which it could participate in the process of the algorithm. This will lead to keeping the dynamism of algorithm in addition to maintaining its convergence sufficiently and stably. Thus, the TGA guarantees not to result in premature convergence or stagnation providing necessary convergence to achieve optimal answer. Moreover, the mutation operator is used more meaningfully in the TGA. Mutation probability has direct relation with parent similarity. This kind of mutation will decrease ineffective mating percent which does not make any improvement in offspring individuals and also it is more natural. Simulation results show that one run of the TGA is enough to reach the optimum answer and the TGA outperforms the standard genetic algorithm.

A stacked structure consisting of ∼ 1 nm-thick MgO and ∼ 4 nm-thick HfO2 was formed on thermally grown SiO2/Si(100) by MOCVD using dipivaloymethanato (DPM) precursors, and the influences of N2 anneal on interfacial reaction and defect state density in this stacked structure were examined. The chemical bonding features of Mg atom were evaluated by using an Auger parameter independently of positive charge-up during XPS measurements. With Mg incorporation into HfO2, a slight decrease in the oxidation number of Mg was detectable. The result suggests that Mg atoms are incorporated preferentially near oxygen vacancies in the HfO2, which can be responsible for a reduction of the flat band voltage shifts observed from C-V characteristics.

We propose a polarization mode dispersion (PMD) design for high-speed wavelength-division multiplexing (WDM) backbone network systems based on field PMD measurements on installed optical fibers for long-term commercial use. Implementing a high-speed network system on an installed fiber requires measuring PMD, because the PMD characteristics of most installed fibers are unknown. For enhanced practicality, we must be able to precisely evaluate PMD characteristics precisely with just one measurement. To understand the statistical properties of measured PMD values, we use the Jones Matrix Eigenanalysis (JME) method to conduct long-term (12 months) PMD measurements on installed fibers. We statistically analyze the measurement results and confirm that the measured values match the theory that considers the accuracy of the measurement instrument. This enables a PMD design of desired outage probability based on PMD measurements of installed fibers. We also carry out a 43-Gb/s return-to-zero differential quadrature phase shift keying (RZ-DQPSK) signal transmission with high PMD fibers in order to confirm the effectiveness of our PMD design. The PMD values of the in-line amplifier transmission line are settled so as to meet the worst value of the design. We confirm that 43-Gb/s RZ-DQPSK signals are stably transmitted at the design value.

For analog applications, the Metal-Insulator-Metal (MIM) capacitance has to be measured at a much higher resolution than using the conventional methods, i.e. to a sub-femto level. A new robust mismatch measurement technique is proposed, which is more accurate and robust compared to the conventional Floating Gate Capacitance Measurement (FGCM) methods. A capacitance mismatching measurement methodology based on Vs is more stable than that based on Vf because the influence of pre-existing charge in the floating-gate can be cancelled in the slope of ΔVs/ΔVf based on Vs. The accuracy of this method is evaluated through silicon measurement in a 0.13 µm technology. It shows that, compared to the ideal value, the average of the new method are within 0.12% compared to 49.23% in conventional method while the standard deviation is within 0.15%.

In this paper, we present a numerical method for the equiripple approximation of IIR digital filters. The conventional rational Remez algorithm quickly finds the squared magnitude response of the optimal IIR digital filters, and then by factorizing it the equiripple filter is obtained. Unlike the original Remez algorithm for FIR filters, it is difficult for the rational Remez algorithm to explicitly control the ratio of ripples between different bands. In the conventional lowpass filter design, for example, when different weights are given for its passband and stopband, one needs to iteratively design the filter by manually changing the weights in order to achieve the ratio of the weights exactly. To address this problem, we modify the conventional algorithm and make it possible to directly control the ripple ratio. The method iteratively solves eigenvalue problems with controlling the ripple ratio. Using this method, the equiripple solutions with desired weights are obtained automatically.