This paper describes a nondestructive measurement method for complex permittivity of dielectric material at pseudo microwave frequencies. The resonator used in this study has a cylindrical cavity filled with a sapphire material of a well known complex permittivity. The resonator is divided into two parts at the center. A dielectric substrate specimen is clamped with these halves. Relative permittivity εand loss tangent tan δ of the specimen are obtained at 3 GHz using the TE011 resonance mode. The accuracy of the present method is evaluated through the comparison of the measured values by the new method with those at around 10 GHz by the conventional empty cavity resonator method. The errors of measurements are smaller than 1% and 1105 for εand tan δ, respectively.

This paper presents an experimental study on the penetration characteristics of submillimeter waves in biological tissues and material. The measured values of the penetration depth in excised natural muscle, fat, and aqueous solution of protein, bovine serum albumin (BSA), over the wavelengths of 281 through 496µm are presented. Penetration depths at these wavelengths are 0.11-0.17mm in the natural pork muscle, and 0.69-0.98mm in the natural pork fat, and are the larger at the longer wavelengths. The values vary considerably from sample to sample. Since the measurement of the penetration depth in this study is shown sufficiently reproducible, the variation of the measured penetration depth is attributed to the variation of natural tissues such as that in water content. It is found that the penetration depth of submillimeter waves in aqueous solution of BSA depends almost linearly on the amount of protein content in the solution, and that the typical values of the penetration depth in the natural muscle roughly agree with that in the 35% aqueous solution of BSA in the submillimeter-wave region.

A noninvasive method for measuring complex permittivity of biological tissues is proposed. The noninvasive method is based on an inverse scattering technique which employs an iterative procedure. The iterative procedure consists of solving an electric field integral equation using the method of moments and minimizing the square difference between calculated and measured scattered fields. Implementation of the noninvasive method requires the knowledge of the target shape, the incident and measured scattered fields. Based on the noninvasive method, a measuring system of complex permittivity is developed and its reliability is verified.

In this paper, an ARMA order selection method is proposed with a fuzzy reasoning method. In order to identify the reference model with the ARMA model, we need to determine its ARMA order. A less or more ARMA order, other than a suitable order causes problems such as; lack of spectral information, increasing calculation cost, etc. Therefore, ARMA order selection is significant for a high accurate ARMA model identification. The proposed method attempts to select an ARMA order of a time-varying model with the following procedures: (1) Suppose the parameters of the reference model change slowly, by introducing recursive fuzzy reasoning method, the estimated order is selected. (2) By introducing a fuzzy c-mean clustering methed, the period of the time during which the reference model is changing is detected and the forgetting factor of the recursive fuzzy reasoning method is set. Further, membership functions used in our algorithm are original, which are realized by experiments. In this paper, experiments are documented in order to validate the performance of the proposed method.

An image type resonator method is proposed as a method to evaluate precisely the temperature dependence of dielectric material. At first, the temperature coefficients of the resonant frequencies, TCf are measured separately using the shielded dielectric resonators of three types; that is a parallel plate type, and an image type, and a MIC type resonator. Secondly, an intrinsic temperature coefficient of the resonant frequency TCf0, which is defined as the temperature coefficient of a resonant frequency when all the stored energy is confined inside a dielectric, is estimated from these measured TCf. Actually, the TCf0 values of a sapphire and (ZrSn) TiO4 rod are estimated from the TCf values measured for the resonators of three types. As a result, for the parallel plate type, the precision of TCf0 is about 0.1 ppm/. For the image and MIC types, the errors of about 0.5 ppm/ in the TCf0 values arise from the errors in the linear expansion coefficients of the resonators, rather than from the experimental errors in TCf. Then, another image type resonator is designed to estimate TCf0 within error of 0.1 ppm/. In this design, dimensions of the shielding cavity is determined to reduce the influence of the errors in the linear expansion coefficients on precision of the TCf0 estimation. Finally, for a (ZrSn) TiO4 ceramic rod, a TCf0 value estimated from TCf measured for the image type resonator is obtained with accuracy of about0.1 ppm/.

A simple method for separating the dissipation factors associated with both conductor losses and dielectric losses of printed circuit boards in microwave frequencies is presented. This method utilizes the difference in dependence of two dissipation factors on the dimensions of bounded stripline resonators using a single printed circuit board specimen as a center strip conductor. In this method, the separation is made through a procedure involving the comparison of the measured values of the total dissipation factor with those numerically calculated for the resonators. A method, which is based on a TEM wave approximation and uses Green's function and a variational principle, is used for the numerical calculation. Both effective conductivity for three kinds of industrial copper conductor supported with a substrate of polymide film and dielectric loss tangent of the substrates are determined using this method from the values of the unloaded Q measured at the 10 GHz region. Radiation losses from the resonator affecting the accuracy of the separation are discussed, as well as the values of the effective conductivity of metals on the polyimide substrate which is calculated using the above method. The resulting values of the effective conductivity agree with those using the triplateline method within 10%.

An estimation method for efficiently calculating the field intensity in the Fresnel region of broadside colinear array antennas is developed, and its performance is experimentally verified. The calculation utilizes only the antenna design data, and is readily applicable to arbitrary array antennas. This method can provide a safety protection zone in the proximity of array antennas, in order to protect radio communication personnel and general public from the potentially hazardous radiofrequency exposure.

It is well known that weather conditions affect the performance of satellite broadcasting receiving systems. For example, snow accretion on antennas degrades the receiving performance seriously because it reduces received signal power and also can increase antenna noise. Since effects of the weather are considered to differ for various types of receiving antenna, an investigation on this phenomenon is very important. A study on weather effects to three types of satellite broadcasting receiving antenna, a planar antenna, a center-fed parabolic reflector antenna, and an offset parabolic reflector antenna, is presented in this paper. Since the performance of receiving antennas can be determined by a parameter G/T, a long-term and continuous measurement of G/T must be performed. Furthermore, the measurement of more than one receiving system should be performed simultaneously. Also, the measurement should be performed in a snowy area (in winter) and a rainy area (in the other seasons) to evaluate the effect of the weather. To fulfil the criterion, a continuous measurement system of G/T has been built in Hokkaido University, Sapporo. Sapporo, which is located at latitude 42 degrees north, has a long and snowy winter, and also has rainy days in the other seasons so that we can evaluate the effect of weather. Using this measurement system, cumulative distributions of measurement results are obtained so that the performance of different types of receiving system can be evaluated. In this paper, some considerations on the noise level are also discussed briefly to evaluate the performance degradation of the receiving systems.

An improved reflection wave method was described for measurement of complex permittivity of low-loss materials over 100MHz-1GHz range. The residual impedance Zr and stray admittance Ys surrounding the test sample, which terminated the transmission line, were evaluated using sapphire as a reference material. The correction by the obtained Zr and Ys gave accurate values of complex permittivities of alumina and mullite ceramics as 100MHz-1GHz.

We studied the supply and removal of oil to and from a thin groove and the consequent insertion loss, aiming at matrix optical waveguide switches that utilize optical reflection and transmission effects at the groove. A robot precisely controlled the position of the removal nozzle and the supply needle by a vision servo. The optimum position for the removal nozzle was at the entrance of the groove to a circular oil pool, and the positioning margin was 10-15µm around the optimum position. The on-off ratio of the switching light power at the optimum position was about 30dB. The removal time was proportional to the kinetic viscosity of the oil, and the optimum height of the removal nozzle was independent of the kinetic viscosity of the oil. An analysis of the insertion loss revealed that the main factor in the loss at the reflection is the tilt of the groove wall.

This paper is concerned with an ITS designed for augmenting a student's capability in problem solving. Discussions are concentrated on helping students acquire strategic knowledge and assisting them to build it in their heads. In this paper, many kinds of strategies are treated from a unified point of view. Based on this consideration, a teaching paradigm of strategic knowledge is presented. The paradigm is realized in an ITS as a training environment for strategic knowledge. Assisting students to learn strategic knowledge, the system sets up an appropriate environment and gives them some appropriate advice in each environment. It is realized as a function of giving them appropriate problems and hints about it. In general, strategic knowledge is a kind of heuristics so that it is not easy to describe their application conditions deterministically and explicitly. For this reason, an ITS for strategic knowledge is required to be designed so as to cover not only the case where expertise is represented explicitly as an executable model but also the case where it is represented only implicitly. To realize this teaching paradigm, situation-dependent knowledge called reminding pattern is prepared in the system. It is represented by a triple of a strategy, a situation, and a key symbol in the situation. It denotes that the key usually reminds students of the strategy in the situation. The system gives students problems including positive/negative examples of applications of each strategy in its problem solving process and hints which remind them of an appropriate strategy and makes them resume the problem solving when they fall into an impasse. In this paper, the structure of the system realizing this teaching paradigm is explained in the domain of proving propositional formulas.

This paper applies the principle of radar polarimetry to the synthetic aperture frequency modulated continuous wave radar. First, the principle of monochromatic wave radar polarimetry using scattering matrix and polarization ratio necessary for introducing polarimetric imaging is given. In order to accommodate this principle to a wideband radar, a scattering matrix must be introduced, because FM-CW radar utilizes a wideband signal. This paper points out that the polarimetric target reflection coefficient obtained by the synthetic aperture FM-CW radar works as the scattering matrix element. This replacement, i.e., polarimetric reflection coefficient = the scattering matrix element, was verified by an experiment based on the polarization ratio which maximizes and minimizes a target. A radar system operative in the microwave X-band was successfully applied to the polarimetric detection of a metallic pipe of different orientations, demonstrating the validity of FM-CW radar polarimetry, and indicating an establishment of full polarimetric radar system.

The development of highly accurate and durable control system is becoming a must for todays high performance automobiles. For example, it is necessary to up-grade todays materials and methods creating more sensitive sensors, higher speed processors and more accurate actuators, while also being more durable. Thus, the development of a CMOS time-to-digital converter LSI with half-nanosecond resolution, which controls only pulse signals was achieved by employing 1.5 µm CMOS technology. The new signal detecting circuit, 1.1 mm2 in size, converts time to numerical values over a wide measurement range (13 bits). The compact digital circuit employs a newly developed "ring gate delay system". Within the LSI the fully digital circuit is highly durable. This allows it to be utilized even under severe conditions (for example an operating ambient temperature of 130). In order to measure time accurately, a method of correcting the variation of measurement time data employing a real-time conversion fully digital circuit is described. This method allows for fully automatic correction with a microcomputer, so no manual adjustment is required. In addition to sensor circuit applications, the LSI has great potential for Application Specific Integrated Circuit, (ASIC) such as a function cell with is a completely new method of measuring time.

Some results are presented of a one-year measurement period on an INTELSAT down link at Ku band with elevation of 14 for concurrent measurements of beacon attenuation, sky noise and point rainfall rate. Also some results are presented of line-of-sight (LOS) link fading characteristics at the same place. The projection of the down link trajectory on earth has nearly the same direction as the LOS path trajectory. The measurement results are compared with the theoretical values according to the CCIR recommended procedures of rain attenuation predictions for tropical regions, especially Surabaya, Indonesia. A record rain attenuation value of 80dB was observed.

A new superresolution technique is proposed for antenna pattern measurements. Unwanted reflected signals often impinge on the antenna when we measure it outdoors. A time-domain superresolution technique (a MUSIC algorithm) has been proposed to eliminate the unwanted signal for a narrow pass-band antenna. The MUSIC algorithm needs many snapshots to obtain a correlation matrix. This is not preferable for antenna pattern measurements because it takes a long time to obtain the data. In this paper, we propose to reduce a noise component (stochastic quantity) using the FFT and gating techniques before we apply the MUSIC. The new technique needs a few snapshots and saves the measurement time.

A new system of measuring the thickness of thin filn or paper using 40 kHz ultrasonic wave in air is described. The thickness of samples measured is smaller by a factor of sevreal hundreds than the wavelength of sound. Experinents with polymer and metal films and paper are described to demonstrate the measurement possibilities.

There have been several studies related to a reduction of the amount of computational resources used by Turing machines. As consequences, linear speed-up theorem" tape compression theorem", and reversal reduction theorem" have been obtained. In this paper, we consider reversal- and leaf-bounded alternating Turing machines, and then show that the number of leaves can be reduced by a constant factor without increasing the number of reversals. Thus our results say that a constant factor on the leaf complexity does not affect the power of reversal- and leaf-bounded alternating Turing machines

A method to measure the displacement from the phase rotation of the Doppler signal including the displacement information of the moving body is proposed, where the displacement resolution can be improved 4 times by making the phase rotation faster. Furthermore, this test system is applied in clinical use. The test system is built up by using a two-phase microwave Doppler sensor covering a 10GHz band, where the Doppler frequency is multiplied 4 times by signal processing. Thus, the resolution is improved from a conventional 12.6mm (in case of 11.9GHz) to 3.15mm, and practical utilization has been attained. The microwave Doppler radar system described in this paper is adequate for the displacement measurement for a relatively fast moving body. As a medical sensor for clinical use, measurement examples of head movement in a vestibule examination (vestibule oculomotor reflexive inspection) and finger movement in a cerebellum function test are given. Furthermore by using two sets of this Doppler radar system, a 2-dimensional measurement of head movement is possible.

Most of actual environmental systems show a complicated fluctuation pattern of non-Gaussian type, owing to various kinds of factors. In the actual measurement, the fluctuation of random signal is usually contaminated by an external noise. Furthermore, it is very often that the reliable observation value can be obtained only within a definite fluctuating amplitude domain, because many of measuring equipments have their proper dynamic range and original random wave form is unreliable at the end of amplitude fluctuation. It becomes very important to establish a new signal detection method applicable to such an actual situation. This paper newly describes a dynamical state estimation algorithm for a successive observation contaminated by the external noise of an arbitrary distribution type, when the observation value is measured through a finite dynamic range of measurement. On the basis of the Bayes' theorem, this method is derived in the form of a wide sense digital filter, which is applicable to the non-Gaussian properties of the fluctuations, the actual observation in a finite amplitude domain and the existence of external noise. Differing from the well-known Kalman's filter and its improvement, the proposed state estimation method is newly derived especially by paying our attention to the statistical information on the observation value behind the saturation function instead of that on the resultant noisy observation. Finally, the proposed method is experimentally confirmed too by applying it to the actual problem for a reverberation time measurement from saturated noisy observations in room acoustics.

Redundancy is introduced by sampling a bandlimited signal at a higher rate than the Nyquist rate. In the cases of erasures due to fading or jamming, the samples are discarded. Therefore, what we get at the output of the receiver is a set if nonuniform samples obtained from a uniform sampling process with missing samples. As long as the rate of nonuniform samples is higher than the Nyquist rate, the original signal can be recovered with no errors. The sampling theorem can be shown to be equivalent to the fundamental theorem of information theory. This oversampling technique is also equivalent to a convolutional code of infinite constraint length is the Field of real numbers. A DSP implementation of this technique is through the use of a Discrete Fourier Transform (DFT), which happens to be equivalent to block codes in the field of real numbers. An iterative decoder has been proposed for erasure and impulsive noise, which also works with moderate amount of additive random noise. The iterative method is very simple and efficient consisting of modules of Fast Fourier Transforms (FFT) and Inverse FFT's. We also suggest a non-linear iterative method which converges faster than the successive approximation. This iterative decoder can be implemented in a feedback configuration. Besides FFT, other discrete transforms such as Discrete Cosine Transform, Discrete Sine Transform, Discrete Hartley Transform, and Discrete Wavelet Transform are used. The results are comparable to FFT with the advantage of working in the field of real numbers.