In this paper, an insect classification method using scanning electron microphotographs is presented. Images taken by a scanning electron microscope (SEM) have a unique problem for classification in that visual features differ from each other by magnifications. Therefore, direct use of conventional methods results in inaccurate classification results. In order to successfully classify these images, the proposed method generates an optimal training dataset for constructing a classifier for each magnification. Then our method classifies images using the classifiers constructed by the optimal training dataset. In addition, several images are generally taken by an SEM with different magnifications from the same insect. Therefore, more accurate classification can be expected by integrating the results from the same insect based on Dempster-Shafer evidence theory. In this way, accurate insect classification can be realized by our method. At the end of this paper, we show experimental results to confirm the effectiveness of the proposed method.

Measurement matrix construction is critically important to signal sampling and reconstruction for compressed sensing. From a practical point of view, deterministic construction of the measurement matrix is better than random construction. In this paper, we propose a novel deterministic method to construct a measurement matrix for compressed sensing, CS-FF (compressed sensing-finite field) algorithm. For this proposed algorithm, the constructed measurement matrix is from the finite field Quasi-cyclic Low Density Parity Check (QC-LDPC) code and thus it has quasi-cyclic structure. Furthermore, we construct three groups of measurement matrices. The first group matrices are the proposed matrix and other matrices including deterministic construction matrices and random construction matrices. The other two group matrices are both constructed by our method. We compare the recovery performance of these matrices. Simulation results demonstrate that the recovery performance of our matrix is superior to that of the other matrices. In addition, simulation results show that the compression ratio is an important parameter to analyse and predict the recovery performance of the proposed measurement matrix. Moreover, these matrices have less storage requirement than that of a random one, and they achieve a better trade-off between complexity and performance. Therefore, from practical perspective, the proposed scheme is hardware friendly and easily implemented, and it is suitable to compressed sensing for its quasi-cyclic structure and good recovery performance.

This letter introduces a non-local means (NLM) denoising algorithm that uses a weight function based on a switching norm. The noise level and local activity are incorporated into the NLM denoising algorithm which enhances performance. This is done by selecting a norm among l1, l2, and l4 norms to determine a weighting function. The experimental results show the capability of the proposed algorithm. In addition, the proposed algorithm is verified as effective for enhancing the performance of other NLM algorithms.

In this paper, we give a formalization of the behavior of the Content-Centric Networking (CCN) protocol with parameterizing content managements. CCN is a communications architecture that is based on the names of contents, rather than on addresses. In the protocol used in CCN, each node sends packets to the nodes that are connected to it, which communicate with further nodes that are connected to them. This kind of behaviors prevents formalizing the CCN protocol as end-to-end communications. In our previous work, we formalized the CCN protocol using the proof assistant Coq. However, in this model, each node in the network can store any number of contents. The storage for each node is usually limited and the node may drop some of the contents due to its filled storage. The model proposed in this paper permits a node to have its own content management method, and still keeps the temporal properties that are also valid in the previous model. To demonstrate difference between these models, we give a specification that is valid in the previous model but invalid in the proposed model, called orthogonality. Since it is generally invalid in CCN, the proposed model is more precise than the previous one.

This paper presents a Multi-channel MAC protocol with channel grouping for multi-channel ad-hoc networks. The proposed protocol has both concepts of the multiple rendezvous and the single control channel protocols, which were proposed as a MAC protocol for multi-channel ad-hoc network without centralized stations. In the proposed protocol, all the channels are divided into some groups and each group has a control channel. Network nodes circulate among the groups and channel negotiations are carried out on a control channel of the group. By applying the channel grouping, it is possible to enhance network throughput without reducing the channel-usage probability. Because there is an optimum group number for obtaining the highest throughput, this paper gives analytical expressions of maximum network throughput for the proposed protocol as a function of system parameters. The effectiveness of the proposed protocol is shown from simulation results. In addition, the validity of the analytical expressions is confirmed from quantitative agreements between analytical predictions and simulation results.

When using a wireless capsule endoscope (WCE), it is important to know WCE location. In this paper, we focus on a time of arrival (TOA)-based localization technique, as it has better location estimation performance than other radio frequency-based techniques. However, the propagation speed of signals transmitted from inside of a human body varies depending on which biological tissues they pass through. For this reason, almost all of conventional TOA-based methods have to obtain the relative permittivity of the passed biological tissues or the propagation speed beforehand through another measurement system, i.e., magnetic resonance imaging (MRI) or computational tomography (CT). To avoid such troublesome pre-measurement, we propose a hybrid TOA/received signal strength indicator (RSSI)-based method, which can simultaneously estimate the WCE location and the averaged relative permittivity of the human body. First, we derive the principle of RSSI-based relative permittivity estimation from an finite difference time domain (FDTD) simulation. Second, we combine the TOA-based localization and the proposed RSSI-based relative permittivity estimation, and add them to the particle filter tracking technique. Finally, we perform computer simulations to evaluate the estimation accuracy of the proposed method. The simulation results show that the proposed method can accomplish good localization performance, 1.3mm, without pre-measurement of the human body structure information.

Spatial stochastic models have been much used for performance analysis of wireless communication networks. This is due to the fact that the performance of wireless networks depends on the spatial configuration of wireless nodes and the irregularity of node locations in a real wireless network can be captured by a spatial point process. Most works on such spatial stochastic models of wireless networks have adopted homogeneous Poisson point processes as the models of wireless node locations. While this adoption makes the models analytically tractable, it assumes that the wireless nodes are located independently of each other and their spatial correlation is ignored. Recently, the authors have proposed to adopt the Ginibre point process — one of the determinantal point processes — as the deployment models of base stations (BSs) in cellular networks. The determinantal point processes constitute a class of repulsive point processes and have been attracting attention due to their mathematically interesting properties and efficient simulation methods. In this tutorial, we provide a brief guide to the Ginibre point process and its variant, α-Ginibre point process, as the models of BS deployments in cellular networks and show some existing results on the performance analysis of cellular network models with α-Ginibre deployed BSs. The authors hope the readers to use such point processes as a tool for analyzing various problems arising in future cellular networks.

This paper presents an analytical model for network throughput of WLANs, taking into account heterogeneous conditions, namely network nodes transmit different length frames with various offered load individually. The airtime concept, which is often used in multi-hop network analyses, is firstly applied for WLAN analysis. The proposed analytical model can cover the situation that there are saturation and non-saturation nodes in the same network simultaneously, which is the first success in the WLAN analyses. This paper shows the network throughput characteristics of four scenarios. Scenario 1 considers the saturation throughputs for the case that one or two length frames are transmitted at the identical offered load. Scenarios 2 and 3 are prepared for investigating the cases that all network nodes transmit different length frames at the identical offered load and identical length frames at the different offered loads, respectively. The heterogeneous conditions for not only frame length but also offered load are investigated in Scenario 4.

In IEEE 802.11 wireless local area networks (WLANs), contention window (CW) in carrier sense multiple access with collision avoidance (CSMA/CA) is one of the most important techniques determining throughput performance. In this paper, we propose a novel CW control scheme to achieve high transmission efficiency in dense user environments. Whereas the standard CSMA/CA mechanism. Employs an adaptive CW control scheme that responds to the number of retransmissions, the proposed scheme uses the optimum CW size, which is shown to be a function of the number of terminal stations. In the proposed scheme, the number of terminal stations are estimated from the probability of packet collision measured at an access point (AP). The optimum CW size is then derived from a theoretical analysis based on a Markov chain model. We evaluate the performance of the proposed scheme with simulation experiments and show that it significantly improves the throughput performance.

This paper presents a modulation scheme for impulse radio that uses the first sidelobe for transmitting a non-return-to-zero baseband signal and the implementation of a dual frequency conversion demodulator. The proposed modulation technique realizes two times higher frequency efficiency than that realized by binary phase-shift keying modulation and does not require an up-converter in the transmitter. The dual frequency conversion demodulator compensates for the spectrum distortion caused by the frequency response of the circuits and channel. The effect of frequency compensation is analytically studied. The fabricated demodulator test chip of 65 nm CMOS achieves clock and data recovery at 5.7 Gbps with a power consumption of 24 mW.

Kiasu-BC is a recently proposed tweakable variant of the AES-128 block cipher. The designers of Kiasu-BC claim that no more than 7-round Meet-in-the-Middle (MitM) attack can be launched against it. In this letter, we present a MitM attack, utilizing the differential enumeration technique, on the 8-round reduced cipher. The attack has time complexity of 2116 encryptions, memory complexity of 286 128-bit blocks, and data complexity of 2116 plaintext-tweak combinations.

We propose a speech analysis method based on the source-filter model using multivariate empirical mode decomposition (MEMD). The proposed method takes multiple adjacent frames of a speech signal into account by combining their log spectra into multivariate signals. The multivariate signals are then decomposed into intrinsic mode functions (IMFs). The IMFs are divided into two groups using the peak of the autocorrelation function (ACF) of an IMF. The first group characterized by a spectral fine structure is used to estimate the fundamental frequency F0 by using the ACF, whereas the second group characterized by the frequency response of the vocal-tract filter is used to estimate formant frequencies by using a peak picking technique. There are two advantages of using MEMD: (i) the variation in the number of IMFs is eliminated in contrast with single-frame based empirical mode decomposition and (ii) the common information of the adjacent frames aligns in the same order of IMFs because of the common mode alignment property of MEMD. These advantages make the analysis more accurate than with other methods. As opposed to the conventional linear prediction (LP) and cepstrum methods, which rely on the LP order and cut-off frequency, respectively, the proposed method automatically separates the glottal-source and vocal-tract filter. The results showed that the proposed method exhibits the highest accuracy of F0 estimation and correctly estimates the formant frequencies of the vocal-tract filter.

This paper presents a weighted diversity combining technique for the cyclostationarity detection based spectrum sensing of orthogonal frequency division multiplexing signals in cognitive radio. In cognitive radio systems, secondary users must detect the desired signal in an extremely low signal-to-noise ratio (SNR) environment. In such an environment, multiple antenna techniques (space diversity) such as maximum ratio combining are not effective because the energy of the target signal is also extremely weak, and it is difficult to synchronize some received signals. The cyclic autocorrelation function (CAF) is used for traditional cyclostationarity detection based spectrum sensing. In the presented technique, the CAFs of the received signals are combined, while the received signals themselves are combined with general space diversity techniques. In this paper, the value of the CAF at peak and non-peak cyclic frequencies are computed, and we attempt to improve the sensing performance by using different weights for each CAF value. The results were compared with those from conventional methods and showed that the presented technique can improve the spectrum sensing performance.

The most commonly used scattering parameters (S parameters) are normalized to a real reference resistance, typically 50Ω. In some cases, the use of S parameters normalized to some complex reference impedance is essential or convenient. But there are different definitions of complex-referenced S parameters that are incompatible with each other and serve different purposes. To make matters worse, different simulators implement different ones and which ones are implemented is rarely properly documented. What are possible scenarios in which using the right one matters? This tutorial-style paper is meant as an informal and not overly technical exposition of some such confusing aspects of S parameters, for those who have a basic familiarity with the ordinary, real-referenced S parameters.

A novel method for illumination-invariant face representation is presented based on the orthogonal decomposition of the local image structure. One important advantage of the proposed method is that image gradients and corresponding intensity values are simultaneously used with our decomposition procedure to preserve the original texture while yielding the illumination-invariant feature space. Experimental results demonstrate that the proposed method is effective for face recognition and verification even with diverse lighting conditions.

In 3GPP (3rd Generation Partnership Project) LTE (Long Term Evolution) systems, when HARQ (Hybrid Automatic Repeat request) retransmission is invoked, the data at the transmitter are retransmitted randomly or sequentially regardless of their relationship to the wrongly decoded data. Such practice is inefficient since precious transmission resources will be spent to retransmit data that may be of no use in error correction at the receiver. This paper proposes an incremental redundancy HARQ scheme based on Error Position Estimating Coding (ePec) and LDPC (Low Density Parity Check Code) channel coding, which is called ePec-LDPC HARQ. The proposal is able to feedback the wrongly decoded code blocks within a specific MAC (Media Access Control) PDU (Protocol Data Unit) from the receiver. The transmitter gets the feedback information and then performs targeted retransmission. That is, only the data related to the wrongly decoded code blocks are retransmitted, which can improve the retransmission efficiency and thus reduce the retransmission overload. An enhanced incremental redundancy LDPC coding approach, called EIR-LDPC, together with a physical layer framing method, is developed to implement ePec-LDPC HARQ. Performance evaluations show that ePec-LDPC HARQ reduces the overall transmission resources by 15% compared to a conventional LDPC HARQ scheme. Moreover, the average retransmission times of each MAC PDU and the transmission delay are also reduced considerably.

In this paper, we present the channel estimation (CE) problem in the orthogonal frequency division multiplexing system with offset quadrature amplitude modulation (OFDM/OQAM). Most CE methods rely on the assumption of a low frequency selective channel to tackle the problem in a way similar to OFDM. However, these methods would result in a severe performance degradation of the channel estimation when the assumption is not quite inaccurate. Instead, we focus on estimating the channel impulse response (CIR) itself which makes no assumption on the degree of frequency selectivity of the channels. After describing the main idea of this technique, we present an iterative CE method that does not require zero-value guard symbols in the preamble and consequently improves the spectral efficiency. This is done by the iterative estimation of the unknown transmitted data adjacent to the preamble. Analysis and simulation results validate the efficacy of the proposed method in multipath fading channels.

The dark channel prior (DCP)-based image dehazing method has been widely used for enhancing visibility of outdoor images. However, since the DCP-based method assumes that the minimum values within local patches of natural outdoor haze-free images are zero, underestimation of the transmission is inevitable when the assumption does not hold. In this letter, a novel iterative image dehazing algorithm is proposed to compensate for the underestimated transmission. Experimental results show that the proposed method can improve the dehazing performance by increasing the transmission estimation accuracy.

This paper presents a K-band fully reconfigurable waveguide resonator filter with a new negative coupling structure. A pair of transmission zeros as well as the center frequency and bandwidth of the presented filter can be adjusted. The filter adopts the concept of a frequency-tunable coupling resonator in designing the coupling structure, which allows for controlling the coupling coefficient. All coupling values in the filter structure can be tuned by adjusting the resonant frequency of each frequency-tunable coupling resonator. This work also presents a design method in detail for the coupling resonator with a negative coupling coefficient. In addition, the approach for separating the resonant peak produced by the coupling resonator with a negative coupling value from the passband for the purpose of improving the stopband performance is described. For verifying the presented filter structure, a fourth-order waveguide filter has been fabricated and measured. The fabricated filter has the center frequency tuning range from 18.34GHz to 18.75GHz, the bandwidth tuning ratio of 1.94 : 1.

To provide a satellite communication system with high reliability for social infrastructure, building flexible beam adapting to change of communication traffic is necessary. Optical Beam Forming Network has the capability of broadband transmission and small light construction. However, in space environment, there are concerns that the reception efficiency is reduced by the relative phase error of receiving signal among antenna elements with temperature fluctuation. To prevent this, we control relative phase among received signals with optical phase locked loop. In this paper, we propose the active optical phased array system using multi dither heterodyning technique for receiving OBF, and present experimental results under temperature fluctuation. We evaluated the stability of relative phase among 3 elements for temperature fluctuation at multiplexer from -15 to 45, and checked the stability of PLL among 3 elements.