We will present the theoretical analysis of and experimental measurements on the transmission characteristics of multi-channel long period fiber gratings in terms of the physical parameters like the separation distance, grating length and number of gratings. These parameters can be used to control the spectral channel spacing, number of channels, loss peak depth, and channel bandwidth of multi-channel long period fiber gratings.

Recent studies on traffic measurement analysis in the various networks (LAN, MAN, WAN) have shown that packet traffic exhibits Self-Similarity. The packet traffic represents some behavior quite different from what it has been assumed. Some papers reported that Self-Similarity degrades the network performance, such as buffer overflow and network congestion. Thus, we need new network control scheme considering Self-Similar properties. The control scheme requires high-speed calculation method of Hurst Parameter. In this paper, we propose high-speed calculation method of Hurst Parameter based on the Variance-Time Plot method, and show its performance. Furthermore, we try to apply this method to the simple network control, in order to show effectiveness of the network control with Self-Similarity.

We demonstrate, through numerical simulations, the possibility of trans-oceanic single channel transmission at 160 Gbit/s with no active control. This was achieved using short period dispersion management, which supports short pulse propagation at practical map strengths. We demonstrate that through careful selection and optimisation of the system parameters the performance of this system can be extended. We also define the tolerable limits of the system to the residual dispersion slope and polarisation mode dispersion.

This paper focuses on a multi-beam combining scheme for DS-CDMA systems, which has RAKE combiners in multiple overlapped beams, in order to increase the reverse link capacity of DS-CDMA. This scheme is a very attractive technique because the maximal ratio combining (MRC) is carried out in space and time domains. However, in a practical situation, since the terminals in own sector are not uniformly located, the interference levels in respective beams are different. Therefore, receivers at the base station do not achieve ideal combining. This paper proposes a multi-beam combining scheme for DS-CDMA systems using weighting factor based on interference level of each beam. A fast closed loop transmission power control (TPC) scheme for the multi-beam combining system is also proposed. It is confirmed by computer simulation that the proposed scheme has excellent performance in the reverse link even if terminals in own sector are not uniformly located.

In this paper, we investigate the performance characteristics of parallel switching architectures constructed by a stack of multistage switching networks. We first find that the performances of the previously proposed parallel switching architectures are much worse than the expected ones from analytic models which are based on the assumption that traffic is uniformly distributed at each stage of a switching network. We show that this phenomenon is closely related to a traffic-distribution capability of a parallel switching system and has a large influence on the performance. From these results, we then propose an architectural solution based on the Generalized Shuffle Network (GSN) and analyze its performance by proposing a new iterative analysis method. The proposed architecture uses self-routing and deflection routing, and inherently has a traffic-distribution capability to improve switch performances such as cell loss and delay in a cost-effective manner. From the comparison of simulation and analysis results, it is shown that the developed models are quite accurate in predicting the performance of a new parallel switching system.

Photonic crystals have seen major advances in the past few years in the optical range. The association of in-plane waveguiding and two-dimensional photonic crystals (PCs) in thin-slab or waveguide structures leads to good 3D confinement with easy fabrication. Such structures, much easier to fabricate than 3D PCs open many exciting opportunities in optoelectronic devices and integrated optics. We present experiments on a variety of structures and devices, as well as modelling tools, which show that 2D PCs etched through waveguides supported by substrates are a viable route to high-performance PC-based photonic integrated circuits (PICs). In particular, they exhibit low out-of-plane diffraction losses. Low-loss waveguides, high finesse microcavities, and their mutual coupling are demonstrated. PACS: 42.70 QS, 42.55 Sa, 42.82 m, 42.50-p.

The effect of wavelength detuning on the device performance of identical-epitaxial-layer (IEL) electroabsorption (EA) modulator integrated distributed feedback (DFB) lasers is studied in detail. Based on the lasing behavior of integrated devices with different amount of wavelength detuning and the photocurrent spectra under different reverse biases, the optimal wavelength detuning is experimentally determined to be around 30-40 nm for our IEL integrated devices. By adopting gain-coupled DFB laser section, integrated devices with optimal wavelength detuning have demonstrated excellent single mode performances. The extinction ratio is measured to be greater than 15 dB at -3 V, and the modulation bandwidth is around 8 GHz.

We have measured the temperature dependence of the gain characteristics in 1.3-µm AlGaInAs/InP strained multiple-quantum-well (MQW) semiconductor lasers using Hakki-Paoli method. By measuring the temperature dependences of the peak gain value and the gain peak wavelength, we evaluated the temperature dependences of the threshold current and the oscillation wavelength, respectively. The small temperature dependence of the threshold current in AlGaInAs/InP lasers is caused by the small temperature dependence of the transparency current density, which is represented by the characteristic temperature TJtr of 116 K. In AlGaInAs/InP high T0 lasers, the temperature dependence of the oscillation wavelength is slightly larger than that in GaInAsP/InP lasers because of the larger temperature dependence of bandgap wavelength 0.55 nm/K.

Voice over IP (VoIP) is a generic name for services, systems and technology for telephony over an IP network. It is also referred to as Internet telephony and IP (Internet Protocol) telephony. Internet telephone client software attracted attention when it first appeared in 1995. Since that, VoIP has rapidly matured into a practical technology, propelled by the popularization and rapid development of the Internet. IP network traffic already exceeds telephone network traffic and is expected to further increase several-fold in the next few years. In future, the telephone network will be integrated into the IP network and telephony will become entirely VoIP. There are three expectations for VoIP. The first is inexpensive telephone service. The second expectation is for integrated telephony and IP network services such as a CTI (Computer Telephony Integration) system in which there is interworking with various Internet applications, such as e-mail and Web call-back for communication services of greater convenience rather than simple replacement of the telephone. The third expectation is for a platform for providing high-quality voice communication, multicast communication, and other such enhanced voice services that have a high degree of freedom. However, many problems remain to be overcome before the VoIP System is realized. The main problems are real-time transmission of voice that allows a smooth conversation, session control for providing a variety of services, and the proposal of new services. In this paper, we give an overview of VoIP and the problems that must be solved in order to realize it and propose some solutions regarding stream control and applications. We also describe session control and other topics that are being discussed in standardization forums.

Highly reliable and high power weakly index guided buried-stripe type 980 nm pump laser diodes developed for undersea applications are reviewed. The 10,000-hour large scale reliability tests of the first generation LD chips shows that 16.7 FIT for the random failure was confirmed at 10C with 60% confidence level at 120 mW output power. We also fabricated a FBG locked co-axial type module using a can-sealed LD with a two-lens system, which showed a stable FBG locked mode oscillation at 980 nm under the temperature range from 5C to 45C. The 5,000-hour heat cycle test of the modules reveals that the cumulative failure rate after 27 years at 10C is expected to be 0.023%. These first generation LD modules were employed in the transoceanic commercial systems such as Pacific Crossing-1 and the Japan-US cable system projects. We have also succeeded in developing the 980 nm LD for higher output operation with optimizing waveguide design. The 1000 µm long LD showed CW kink-free operation up to 545 mW optical output and a maximum output power of over 650 mW, which was limited by thermal rollover. In addition, a preliminary aging test at 350 mW optical output power at 50C has shown stable operation up to 2,300 h. We also confirmed 300 mW kink-free fiber output power with a co-axial type module with the improved coupling efficiency of approximately 78%. These figures are the highest reported operation levels for 980-nm co-axial type modules.

In an ideal fiber grating having a uniform refractive index modulation, the reflection or the transmission spectrum is symmetric with equal amount of side lobes on both sides of the resonant wavelength of the fiber grating. It is observed that a long-period fiber grating made by a non-uniform UV laser beam through a uniform amplitude mask has an asymmetric transmission spectrum. The asymmetric characteristic is explained with Mach-Zehnder effect in the long-period fiber grating. The non-uniform UV laser beam makes also a non-uniform index modulation along the fiber core. Therefore, a beam coupled to a cladding mode at a section of the grating can be re-coupled to the core mode after passing a certain distance. The re-coupled beam makes Mach-Zehnder-like interference with the un-coupled core mode. However, it is presented that the asymmetric phenomenon can be overcome by scanning the UV laser beam along the fiber over the mask. The beam scanning method is able to suffer the same fluence of the UV laser beam on the fiber. Finally, a linearly chirped long-period fiber grating was made using the non-uniform UV laser beam. Due to the asymmetricity the chirping effect was not clearly observed. It is also presented that the beam scanning method could remove the asymmetric problem and recover the typical spectrum of the linearly chirped fiber grating.

In order to realize automatic-level-controlled (ALC) erbium doped fiber amplifiers (EDFAs) with both wide dynamic range and good noise performance, we propose EDFAs employing the automatic power control (APC) scheme and a variable attenuation slope compensator (VASC). The VASC consists of two asymmetrical Mach-Zehnder interferometers (MZIs) concatenated in series and thermo optic (TO) heaters are attached to the arms of each MZIs. By adjusting the electric power supplied to the TO heaters, an almost linear attenuation slope can be varied by plus minus 5 dB or more over the operational wavelength band of 30 nm. The EDFA employing the APC scheme and the VASC has exhibited a dynamic range as large as 20 dB with the output power variation as small as 0.7 dB, which is as good as that of the EDFA employing the APC scheme and a variable optical attenuator (VOA). The noise figure (NF) of the EDFA employing the VASC was degraded about 4.1 dB with increasing the input power by 20 dB, while it was degraded about 7.3 dB with increasing the input power by only 15 dB in the EDFA employing the VOA. The EDFA employing the VASC can realize the ALC operation over a wider dynamic range with reduced noise figure degradation. In the EDFA employing the VASC, the power excursion was suppressed to less than 1.1 dB, when the input signal level was changed between -23 dBm/ch and -18 dBm/ch with the rise/fall time of 8 ms.

This paper proposes a nonlinear distortion suppression scheme for optical direct FM Radio-on-Fiber system. This scheme uses the interaction between the nonlinearities of DFM-LD and OFD to suppress a 3rd order intermodulation distortion. We theoretically analyze the carrier to noise-plus-distortion ratio (CNDR) and show a controlling method in the MZI type OFD to realize the proposed suppression scheme.

In erbium doped optical fiber amplifiers (EDFAs) used in modern high-capacity wavelength division multiplexing (WDM) systems, the gain flatness of EDFA is very important in wide-band long-haul systems. In the EDFAs using the passive gain equalizers, the gain flatness deteriorates due to gain-tilt when the operating condition of the EDFA changes, while the EDFAs should maintain the gain flatness even if the operating condition has changed. To solve this problem, we have developed an active gain-slope compensation technique of an EDFA using a thulium-doped optical fiber (TDF) as a saturable absorber. The actively gain-slope compensated EDFA with the TDF compensator keeps the gain profile constant for the wide gain dynamic range more than 8 dB with the low noise figure less than 6 dB in the wavelength range of 1539-1564 nm.

We will present the theoretical analysis of and experimental measurements on the transmission characteristics of multi-channel long period fiber gratings in terms of the physical parameters like the separation distance, grating length and number of gratings. These parameters can be used to control the spectral channel spacing, number of channels, loss peak depth, and channel bandwidth of multi-channel long period fiber gratings.

An experimental report was presented on a high temperature performance of a ZrN barrier in the model system of W/ZrN/poly-Si as a poly-metal gate electrode configuration. The absence of interdiffusion, reaction and/or mixing of the ZrN barrier with adjoining W and poly-Si layers resulted in a successful demonstration of the thermally stable poly-metal gate electrode configuration which tolerated annealing at 850 for 1 h.

The uniform switching system is the family of non-linear n m binary arrays constrained such that all columns are from the constant weight k vectors and all rows have weights divisible by p > 0. For this system, we present a cardinality formula and an enumerative algorithm.

A new algorithm called core-stateless random-early-detection (CS-RED) is described. This algorithm can improve the fairness characteristics under a wide range of network conditions and is robust in terms of the setting of its control parameters. It can be used in a distributed architecture, as can the core-stateless fair-queuing (CSFQ) algorithm, so it is applicable to large-capacity backbone routers. Through a detailed evaluation, we have identified and clarified the fairness degradation problem in the CSFQ algorithm. We solved this problem by incorporating the congestion notification proposed in the RED algorithm into CSFQ; we call this hybrid CS-RED. Comparison of the fairness characteristics in a computer-simulated network using either the CS-RED or CSFQ algorithm showed that a higher level of fairness is achieved with the CS-RED algorithm under a wide variety of network conditions without degrading link utilization. Furthermore, the CS-RED algorithm uses a treatment that is more general than the penalty box mechanism to penalize unresponsive flows in best-effort networks.

Caching at the Web proxy server plays an important role in reducing the response time, the network traffic, and the load of Web servers. Many recent studies have proposed and examined the replacement and consistency policies for the proxy cache, which plays a central role in the performance of caching components. For better performance, they exploit various metadata of Web objects, such as the reference count, reference time, and modification time information of past behaviors, to estimate the re-reference likelihood and freshness of the objects. However, all of these known to the authors use the metadata only when the actual object is in the cache. We observed from various proxy traces that about 20-30% of clients' requests incurred only the validity checks of cached objects without transferring actual objects from the proxy server. In this case, only the metadata are necessary at the proxy server. This paper proposes a proxy cache consistency policy that uses the metadata even for absent objects. These include the time information of evicted objects from the cache and those out of the header-only replies from Web servers. Trace-driven simulations with public proxy cache traces show that our policy reduces the response time and the number of connections to Web servers significantly.

In erbium doped optical fiber amplifiers (EDFAs) used in modern high-capacity wavelength division multiplexing (WDM) systems, the gain flatness of EDFA is very important in wide-band long-haul systems. In the EDFAs using the passive gain equalizers, the gain flatness deteriorates due to gain-tilt when the operating condition of the EDFA changes, while the EDFAs should maintain the gain flatness even if the operating condition has changed. To solve this problem, we have developed an active gain-slope compensation technique of an EDFA using a thulium-doped optical fiber (TDF) as a saturable absorber. The actively gain-slope compensated EDFA with the TDF compensator keeps the gain profile constant for the wide gain dynamic range more than 8 dB with the low noise figure less than 6 dB in the wavelength range of 1539-1564 nm.