The adiabatic quantum-flux-parametron (AQFP) is an energy-efficient superconductor logic device. In a previous study, we proposed a low-latency clocking scheme called delay-line clocking, and several low-latency AQFP logic gates have been demonstrated. In delay-line clocking, the latency between adjacent excitation phases is determined by the propagation delay of excitation currents, and thus the rising time of excitation currents should be sufficiently small; otherwise, an AQFP gate can switch before the previous gate is fully excited. This means that delay-line clocking needs high clock frequencies, because typical excitation currents are sinusoidal and the rising time depends on the frequency. However, AQFP circuits need to be tested in a wide frequency range experimentally. Hence, in the present study, we investigate AQFP circuits adopting delay-line clocking with square excitation currents to apply delay-line clocking in a low frequency range. Square excitation currents have shorter rising time than sinusoidal excitation currents and thus enable low frequency operation. We demonstrate an AQFP buffer chain with delay-line clocking using square excitation currents, in which the latency is approximately 20ps per gate, and confirm that the operating margin for the buffer chain is kept sufficiently wide at clock frequencies below 1GHz, whereas in the sinusoidal case the operating margin shrinks below 500MHz. These results indicate that AQFP circuits adopting delay-line clocking can operate in a low frequency range by using square excitation currents.

As process technologies advance, timing-error correction techniques have become important as well. A suspicious timing-error prediction (STEP) technique has been proposed recently, which predicts timing errors by monitoring the middle points, or check points of several speed-paths in a circuit. However, if we insert STEP circuits (STEPCs) in the middle points of all the paths from primary inputs to primary outputs, we need many STEPCs and thus require too much area overhead. How to determine these check points is very important. In this paper, we propose an effective STEPC insertion algorithm minimizing area overhead. Our proposed algorithm moves the STEPC insertion positions to minimize inserted STEPC counts. We apply a max-flow and min-cut approach to determine the optimal positions of inserted STEPCs and reduce the required number of STEPCs to 1/10-1/80 and their area to 1/5-1/8 compared with a naive algorithm. Furthermore, our algorithm realizes 1.12X-1.5X overclocking compared with just inserting STEPCs into several speed-paths.

In this paper, we propose a new design technique called extit{asynchronous multi-frequency clocking} for suppressing EMI at a chip design level by combining two independent EMI-suppressing approaches: extit{multi-frequency clocking} and extit{asynchronous circuit design} techniques. To show the effectiveness of our approach, a five-stage pipelined asynchronous MIPS with multi-frequency clocking has been implemented on a commercial Xilinx FPGA device. Our approach shows 11.05 dB and 5.88 dB reductions of peak EM radiation in the prototyped implementation when compared to conventional synchronous and bundled-data asynchronous circuit counterparts, respectively.

The impact of clock-skew on circuit timing increases rapidly as technology scales. As a result, it becomes important to deal with clock-skew at the early stages of circuit designs. This paper presents a novel datapath design that aims at mitigating the impact of clock-skew in high-level synthesis, by integrating margin (evaluated as the maximum number of clock-cycles to absorb clock-skew) and ordered clocking into high-level synthesis tasks. As a first attempt to the proposed datapath design, this paper presents a 0-1 integer linear programming formulation that focuses on register binding to achieve the minimum cost (the minimum number of registers) under given scheduling result. Experimental results show the optimal results can be obtained without increasing the latency, and with a few extra registers compared to traditional high-level synthesis design.

For recent and future nanometer-technology VLSIs, static and dynamic delay variations become a serious problem. In many cases, the hold timing constraint, as well as the setup timing constraint, becomes critical for latching a correct signal under delay variations. While the timing violation due to the fail of the setup timing constraint can be fixed by tuning a clock frequency or using a delayed latch, the timing violation due to the fail of the hold timing constraint cannot be fixed by those methods in general. Our approach to delay variations (in particular, the hold timing constraint) proposed in this paper is a novel register assignment strategy in high-level synthesis, which guarantees safe clocking by Backward-Data-Direction (BDD) clocking. One of the drawbacks of the proposed register assignment is the increase in the number of required registers. After the formulation of this new register minimization problem, we prove NP-hardness of the problem, and then derive an integer linear programming formulation for the problem. The proposed method receives a scheduled data flow graph, and generates a datapath having (1) robustness against delay variations, which is ensured by BDD-based register assignment, and (2) the minimum possible number of registers. Experimental results show the effectiveness of the proposed method for some benchmark circuits.

A transceiver macro for high-speed data transmission via cable in vehicles is proposed. The transceiver uses ac coupling and bi-directional interface topology for protecting LSIs against unexpected short of cable and harness/chassis and has a spread-spectrum-clocking (SSC) generator that reduces noise due to electromagnetic interference. A driver current control has been used for fast switching of data direction on ac-coupled interfaces. An adaptive bandwidth control has been used in a Δ ∑ PLL to improve SCC significantly. A test chip has been fabricated and shows stable and bi-directional data communication with data rate of 162 to 972 Mbps through 20-m cable. Thanks to an optimum calibration of the SSC-PLL bandwidth, it reduces peak power at 33 kHz by -23 dB and provides 2% modulation at a data rate of 810 Mbps.

In this paper, we examine the effectiveness of clock control in protecting stream ciphers from a distinguishing attack, and show that this form of control is effective against such attacks. We model two typical clock-controlled stream ciphers and analyze the increase in computational complexity for these attacks due to clock control. We then analyze parameters for the design of clock-controlled stream ciphers, such as the length of the LFSR used for clock control. By adopting the design criteria described in this paper, a designer can find the optimal length of the clock-control sequence LFSR.

A Spread Spectrum Clock Generator (SSCG) using Digital Tracking scheme (DT-SSCG) is described. Using digital tracking control outside a PLL, DT-SSCG can realize stable modulation characteristic independent of the PLL constants. Moreover, DT-SSCG can apply to various modulation profiles easily by brief change of the digital tracking parameters. A test chip has realized the fitting of 5000 ppm downspread with 6.02 dB and 8.02 dB spectrum peak reduction for triangle and Non-Linear modulation.

In this paper, we propose an advanced structure of the interface circuit, called a wrapper, for Globally Asynchronous Locally Synchronous (GALS) systems. The proposed wrapper is composed of a sender module and a receiver module. The sender module carries out data transfers in an efficient way by decoupling dependency between an external handshake protocol and an internal clock. The decoupling effect allows the external handshake protocol and the internal clock to be executed in a concurrent way and hence allows the wrapper to show better performance. We have designed our wrapper at the transistor level with 0.35-µm technology. When we compare our decoupled wrapper with two conventional wrappers based on pausible clocking scheme, our simulation results show that performance improvement is about 8-13% and 13-56%, respectively.

Timing verification of digital synchronous designs is a complex process that is traditionally carried out deep in the design cycle, at the gate level. A method, embodied in a C++ based design system, is presented that allows modeling and verification of clock regions at a higher level. By combining event-driven, clock-cycle true and behavioral simulation, we are able to perform static and dynamic timing analysis of the clock regions.

A new flip-flop configuration for half-swing clocking is proposed to save total clocking power. In the proposed scheme, only NMOS's are clocked with the half-swing clock in order to make it operate without level converters or any additional logics which were used in the earlier half-swing clocking schemes. Vcc is supplied to the random logic circuits and flip-flops while Vcc/2 is supplied to the clock network and some parts of the flip-flop to reduce the power consumed in the clock network. Compared to the conventional scheme, the proposed flip-flop configuration can save the clocking power by 40%.

A half-swing clocking scheme with a complementary gate and source drive is proposed for a CMOS flip-flop to reduce the power consumption of the clock system by 43%, while keeping the flip-flop delay time the same as that of the conventional full-swing clocking scheme. The delay time of the preceding half stage of a flip-flop using this scheme is less than half of that using the previous half-swing clocking scheme.

A new multiple-valued current-mode (MVCM) integrated circuit using a switched current-source control technique is proposed for a 1.5 V-supply high-speed arithmetic circuit with low-power dissipation. The use of a differential logic circuit (DLC) with a pair of dual-rail inputs makes the input voltage swing small, which results in a high driving capability at a lower supply voltage, while having large static power dissipation. In the proposed DLC using a switched current control technique, the static power dissipation can be greatly reduced because current sources in non-active circuit blocks are turned off. Since the gate of each current source is directly controlled by using a multiphase clock whose technique has been already used in dynamic circuit design, no additional transistors are required for currentsource control. As a typical example of arithmetic circuits, a new 1.5 V-supply 5454-bit multiplier based on a 0.8µm standard CMOS technology is also designed. Its performance is about 1.3 times faster than that of a binary fastest multiplier under the normalized power dissipation. A prototype chip is also fabricated to confirm the basic operation of the proposed MVCM integrated circuit.

In this paper we describe a method for resynthesizing the controller of a design for a fixed datapath with the objective of increasing the design's throughput by minimizing its total execution time. This work has tremendous potential in two important areas: one, design reuse for retargetting datapaths to new libraries, new technologies and different bit-widths; and two, back-annotation of physical design information during High-Level Synthesis (HLS), and subsequent adjustment of the design's schedule to account for realistic physical design information with minimal changes to the datapath. We present our approach using various formulations, prove optimality of our algorithm and demonstrate the effectiveness of our technique on several HLS benchmarks. We have observed improvements of up to 34% in execution time after straightforward application of our controller resynthesis technique to the outputs of HLS.

A novel external clocking magnetic disk recording channel is proposed and examined. Timing not only for data recovery but for recording is given by a bit clock which is synchronized with dedicated clock marks on patterned discrete track media. Jitter of the bit clock is 2.5 ns (rms), which is good enough for data rates up to about 20 Mbit/s. Using an MR/Inductive head and PRML (Partial Response Maximum Likelihood) signal processing, an error rate of 110-6 is obtained at linear density 3146 bit/mm.