Hong ZHANG Xue LI Suming LAI Pinyi REN
Source-follower-based (SFB) continuous-time low-pass filters (LPF) have the advantages of low power and high linearity over other filter topologies. The second-order SFB filter cells, which are key building blocks for high-order SFB filters, are often realized by composite source follower with positive feedback. For a single branch 2nd-order SFB cell, the linearity drops severely at high frequencies in the pass band because its slew-rate is restricted by the Q factor and the pole frequency. The folded 2nd-order SFB cell provides higher linearity because it has two DC branches, and hence has another freedom to increase the slew rate. However, because of the positive feedback, the folded and unfolded 2nd-order SFB cells, especially those with high Q factors, tend to be unstable and act as relaxation oscillators under given circuit parameters. In order to obtain higher Q factor, a new topology for the 2nd-order SFB cell without positive feedback is proposed in this paper, which is unconditionally stable and can provide high linearity. Based on the folded 2nd-order SFB cell and the proposed high-Q SFB cell, a 264 MHz sixth-order LPF with 3 stages for ultra wideband (UWB) applications is designed in 0.18 µm CMOS technology. Simulation results show that the LPF achieves an IIP3 of above 12.5 dBm in the whole pass band. The LPF consumes only 4.1 mA from a 1.8 V power supply, and has a layout area of 200 µm 150 µm.
Jaejun LEE Sungho LEE Sangwook NAM
This paper presents a circuit that improves supply noise rejection using an active inductor circuit. Compared to the conventional designs, the proposed supply noise suppression circuit has better characteristics such as low current consumption and small die size with noise rejection. The circuit was fabricated using 0.13 µm UMC CMOS technology. The experimental results showed that the supply noise was suppressed by 61% with only an increase in size of 20.0 µm 2.5 µm, and the current consumption was under 2 mA.
Tatsunori OBARA Kazuki TAKEDA Fumiyuki ADACHI
Frequency-domain equalization (FDE) based on minimum mean square error (MMSE) is considered as a promising equalization technique for a broadband single-carrier (SC) transmission. When a square-root Nyquist filter is used at a transmitter and receiver to limit the signal bandwidth, the presence of timing offset produces the inter-symbol interference (ISI) and degrades the bit error rate (BER) performance using MMSE-FDE. In this paper, we discuss the mechanism of the BER performance degradation in the presence of timing offset. Then, we propose joint MMSE-FDE & spectrum combining which can make use the excess bandwidth introduced by transmit filter to achieve larger frequency diversity gain while suppressing the negative effect of the timing offset.
In this paper, we propose a robust state estimation method using a particle filter (PF) for a class of nonlinear systems which have stochastic parameter uncertainties. A robust PF was designed using prediction and correction structure. The proposed PF draws particles from a simple proposal density function and corrects the particles with particle-wise correction gains. We present a method to obtain an error variance of each particle and its upper bound, which is minimized to determine the correction gain. The proposed method is less restrictive on system nonlinearities and noise statistics; moreover, it can be applied regardless of system stability. The effectiveness of the proposed robust PF is illustrated via an example based on Chua's circuit.
Tetsuya YAMAMOTO Kazuki TAKEDA KyeSan LEE Fumiyuki ADACHI
Recently, assuming ideal brick-wall transmit filtering, we proposed a frequency-domain block signal detection (FDBD) with maximum likelihood detection employing QR decomposition and M-algorithm (called QRM-MLD) for the reception of single-carrier (SC) signals transmitted over a frequency-selective fading channel. QR decomposition (QRD) is applied to a concatenation of the propagation channel and discrete Fourier transform (DFT). However, a large number of surviving paths is required in the M-algorithm to achieve sufficiently improved bit error rate (BER) performance. The introduction of filtering can achieve improved BER performance due to larger frequency diversity gain while keeping a lower peak-to-average power ratio (PAPR) than orthogonal frequency division multiplexing (OFDM). In this paper, we develop FDBD with QRM-MLD for filtered SC signal reception. QRD is applied to a concatenation of transmit filter, propagation channel, and DFT. We evaluate BER and throughput performances by computer simulation. From performance evaluation, we discuss how the filter roll-off factor affects the achievable BER and throughput performances and show that as the filter roll-off factor increases, the required number of surviving paths in the M-algorithm can be reduced.
Yu TAKASE Osamu MUTA Yoshihiko AKAIWA
A major drawback in OFDM systems is that the transmit-signal exhibits a high Peak-to-Average Power Ratio (PAPR) which causes nonlinear distortion at the output of power amplifier. To achieve high efficiency in OFDM systems, it is important to suppress PAPR of the transmit signal. In IEEE802.16e (mobile WiMAX) based systems, it is desirable to employ a simple PAPR reduction method such as clipping & filtering (C&F) or peak windowing (PW). The purpose of this paper is to evaluate PAPR reduction performance of C&F and PW and compare them in an IEEE802.16e based OFDM system. In addition, we also show a repeated PW method which reduces PAPR by repeatedly applying a smooth window function to the transmit signal. Computer simulation results show that the repeated PW can achieve almost the same PAPR reduction performance as that of the repeated C&F with significantly lower computational complexity.
Chih-Hao LU Ching-Wen HSUE Bin-Chang CHIEU Hsiu-Wei LIU
This paper presents an ultra-wideband amplifier embedded with band-pass filter design. The scattering parameters of a frequency-domain GaAs field effect transistor are converted into z-domain representations by employing the weighted linear least squares method. A least squares scheme is employed to obtain characteristic impedances of transmission line elements that form the amplifier having a flat gain in the passband and good fall-off selectivity in the stopband. Experimental results illustrate the validity of the proposed design method.
Kenji SUZUKI Mamoru UGAJIN Mitsuru HARADA
A fifth-order switched-capacitor (SC) complex filter was implemented in 0.2-µm CMOS technology. A novel SC integrator was developed to reduce the die size and current consumption of the filter. The filter is centered at 24.730.15 kHz (3δ) and has a bandwidth of 20.260.3 kHz (3δ). The image channel is attenuated by more than 42.6 dB. The in-band third-order harmonic input intercept point (IIP3) is 17.3 dBm, and the input referred RMS noise is 34.3 µVrms. The complex filter consumes 350 µA with a 2.0-V power supply. The die size is 0.578 mm2. Owing to the new SC integrator, the filter achieves a 27% reduction in die size without any degradation in its characteristics, including its noise performance, compared with the conventional equivalent.
This paper introduces a practical color filter array (CFA) interpolation technique. Among the many technologies proposed in this field, the inter-color methods that exploit correlation between color planes generally outperform the intra-color approaches. We have found that the filtering direction, e.g., horizontal or vertical, is among the most decisive factors for the performance of the CFA interpolation. However, most of the state-of-the-art technologies are not flexible enough in determining the filtering direction. For example, filtering only in the upper direction is not usually supported. In this context, we propose an inter-color CFA interpolation using a local map called unified geometry map (UGM). In this method, the filtering direction is determined based on the similarity of the local map data. Thus, it provides more choices of the filtering directions, which enhances the probability of finding the most appropriate direction. It is confirmed through simulations that the proposal outperforms the state-of-the-art algorithms in terms of objective quality measures. In addition, the proposed scheme is as inexpensive as the conventional methods with regard to resource consumption.
Young-Pyo HONG Seong-Sik MYOUNG Jong-Gwan YOOK
A low-loss ultra-wide band (UWB) filter is presented, which uses miniaturized parallel coupled line along with an standard printed circuit board (PCB) technology. By analyzing even- and odd-mode impedances (in comparison with conventional parallel coupled lines) of miniaturized parallel coupled line, this structure provides tight coupling, thus, relaxing the requirements on physical dimensions width and spacing when designing broadband filters. A bandpass filter for Mode 1 (the first 3 sub-bands) in the 3.1-5 GHz band for Multi-Band Orthogonal Frequency Division Multiplexing (MB-OFDM) UWB is realized and compared with a conventional parallel coupled line filter. The experimental results show as much as 0.9 dB insertion loss improvement over the conventional counterpart.
Takao JINNO Yusuke SAITO Masahiro OKUDA
In this paper, we present a numerical method for the equiripple approximation of IIR digital filters. The conventional rational Remez algorithm quickly finds the squared magnitude response of the optimal IIR digital filters, and then by factorizing it the equiripple filter is obtained. Unlike the original Remez algorithm for FIR filters, it is difficult for the rational Remez algorithm to explicitly control the ratio of ripples between different bands. In the conventional lowpass filter design, for example, when different weights are given for its passband and stopband, one needs to iteratively design the filter by manually changing the weights in order to achieve the ratio of the weights exactly. To address this problem, we modify the conventional algorithm and make it possible to directly control the ripple ratio. The method iteratively solves eigenvalue problems with controlling the ripple ratio. Using this method, the equiripple solutions with desired weights are obtained automatically.
Man FENG Lenan WU Jiajia DING Chenhao QI
The extended binary phase shift keying (EBPSK) transmission system with ultra narrow bandwidth has excellent BER performance, which raises many doubts with the researchers. Therefore, on the premise of the existence of a special filter that can transform the modulated phase information into amplitude information, the theoretical BER formula of EBPSK system in Additive White Gaussian Noise (AWGN) channel has been deduced. This paper gives the theoretical values of the parameters in the above BER formula and discusses the effects of parameters on BER firstly. Then the paper shows that the special impacting filter satisfies the above assumption, therefore, in the frame of binary detection theory, the excellent performance of high-efficiency EBPSK system can be explained and the correction of the theoretical BER formula can be validated.
Yong-Kyu KIM Chang-Seok CHOI Hanho LEE
This paper presents a low complexity partially folded architecture of transposed FIR filter and cubic B-spline interpolator for ATSC terrestrial broadcasting systems. By using the multiplexer, the proposed FIR filter and interpolator can provide high clock frequency and low hardware complexity. A binary representation method was used for designing the high order FIR filter. Also, in order to compensate the truncation error of FIR filter outputs, a fixed-point range detection method was used. The proposed partially folded architecture was designed and implemented with 90-nm CMOS technology that had a supply voltage of 1.1 V. The implementation results show that the proposed architectures have 12% and 16% less hardware complexity than the other kinds of architecture. Also, both the filter and the interpolator operate at a clock frequency of 200 MHz and 385 MHz, respectively.
Kaipeng LIU Binxing FANG Weizhe ZHANG
With the emergence of Web 2.0, social tagging systems become highly popular in recent years and thus form the so-called folksonomies. Personalized tag recommendation in social tagging systems is to provide a user with a ranked list of tags for a specific resource that best serves the user's needs. Many existing tag recommendation approaches assume that users are independent and identically distributed. This assumption ignores the social relations between users, which are increasingly popular nowadays. In this paper, we investigate the role of social relations in the task of tag recommendation and propose a personalized collaborative filtering algorithm. In addition to the social annotations made by collaborative users, we inject the social relations between users and the content similarities between resources into a graph representation of folksonomies. To fully explore the structure of this graph, instead of computing similarities between objects using feature vectors, we exploit the method of random-walk computation of similarities, which furthermore enable us to model a user's tag preferences with the similarities between the user and all the tags. We combine both the collaborative information and the tag preferences to recommend personalized tags to users. We conduct experiments on a dataset collected from a real-world system. The results of comparative experiments show that the proposed algorithm outperforms state-of-the-art tag recommendation algorithms in terms of prediction quality measured by precision, recall and NDCG.
In JPEG2000, the Cohen-Daubechies-Feauveau (CDF) 9/7-tap wavelet filter was implemented by using the conventional lifting scheme. However, the filter coefficients remain complex, and the conventional lifting scheme disregards image edges in the coding process. In order to solve these issues, we propose a lifting scheme in two steps. In the first step, we select the appropriate filter coefficients; in the second step, we employ a median operator to regard image edges. Experimental results show that the peak signal-to-noise ratio (PSNR) value of the proposed lifting scheme is significantly improved, by up to 0.75 dB on average, compared to that of the conventional lifting scheme in the CDF 9/7-tap wavelet filter of JPEG2000.
Yosuke TAKEUCHI Koichi ICHIGE Koichi MIYAMOTO Yoshio EBINE
This paper presents a novel automated microwave filter tuning method based on successive optimization of phase and amplitude characteristics. We develop an optimization procedure to determine how much the adjusting screws of a filter should be rotated. The proposed filter tuning method consists of two stages; coarse and fine tuning stages. In the first stage, called coarse tuning, the phase response error of the target filter is minimized so that the filter roughly approximates almost ideal bandpass characteristics. Then in the second stage, called fine tuning, two different amplitude response errors are minimized in turn and then the resulting filter well approximate the ideal characteristics. Performance of the proposed tuning procedure is evaluated through some experiments of actual filter tuning.
Retdian NICODIMUS Shigetaka TAKAGI
This paper proposes a technique to reduce the capacitance spread in switched-capacitor (SC) filters. The proposed technique is based on a simple charge distribution and partial charge transfer which is applicable to various integrator topologies. An implementation example on an existing integrator topology and a design example of a 2nd-order SC low-pass filter are given to demonstrate the performance of the proposed technique. A design example of an SC filter show that the filter designed using the proposed technique has an approximately 23% less total capacitance than the one of SC low-pass filter with conventional capacitance spread reduction technique.
Shoichi KITAGAWA Yoshinobu KAJIKAWA
In this letter, the compensation ability of nonlinear distortions for loudspeaker systems is demonstrated using dynamic distortion measurement. Two linearization methods using a Volterra filter and a Mirror filter are compared. The conventional evaluation utilizes swept multi-sinusoidal waves. However, it is unsatisfactory because wideband signals such as those of music and voices are usually applied to loudspeaker systems. Hence, the authours use dynamic distortion measurement employing a white noise. Experimental results show that the two linearization methods can effectively reduce nonlinear distortions for wideband signals.
Yi CAI Jin-Xing CAI Carl R. DAVIDSON Dmitri G. FOURSA Alan J. LUCERO Oleg V. SINKIN Yu SUN Alexei N. PILIPETSKII Georg MOHS Neal S. BERGANO
We review our recent work on ultra-long-haul wavelength division multiplexed (WDM) transmission with high spectral efficiency (SE) employing tight pre-filtering and multi-symbol detection. We start the discussion with a theoretical evaluation of the SE limit of pre-filtered modulation in optical fiber communication systems. We show that pre-filtering induced symbol correlation generates a modulation with memory and thus, a higher SE limit than that of the original memory-less modulation. We also investigate the merits of utilizing the pre-filtering induced symbol correlation with multi-symbol detection to achieve high SE transmission. We demonstrate transoceanic WDM transmission of a pre-filtered polarization division multiplexed return-to-zero quaternary phased shift keying (PDM-RZ-QPSK) modulation format with multi-symbol detection, achieving 419% SE which is higher than the SE limit of the original memory-less PDM-RZ-QPSK format.
Nagato UEDA Eiji WATANABE Akinori NISHIHARA
This paper proposes a synthesis method of 2-channel IIR paraunitary filter banks by successive extraction of 2-port lattice sections. When a power symmetry transfer function is given, a filter bank is realized as cascade of paraunitary 2-port lattice sections. The method can synthesize both odd- and even-order filters with Butterworth or elliptic characteristics. The number of multiplications per second can also be reduced.