Kenta NIWA Takanori NISHINO Kazuya TAKEDA
A sound field reproduction method is proposed that uses blind source separation and a head-related transfer function. In the proposed system, multichannel acoustic signals captured at distant microphones are decomposed to a set of location/signal pairs of virtual sound sources based on frequency-domain independent component analysis. After estimating the locations and the signals of the virtual sources by convolving the controlled acoustic transfer functions with each signal, the spatial sound is constructed at the selected point. In experiments, a sound field made by six sound sources is captured using 48 distant microphones and decomposed into sets of virtual sound sources. Since subjective evaluation shows no significant difference between natural and reconstructed sound when six virtual sources and are used, the effectiveness of the decomposing algorithm as well as the virtual source representation are confirmed.
Yong-Hwa KIM Jong-Ho LEE Seong-Cheol KIM
This letter corrects some errors on a previous letter concerning the derivation of the covariance matrix of phase noise. This derivation doesn't affect the results of the previous letter.
With the rapid progress of electronic and information technology, an expectation for the realization of body area network (BAN) by means of ultra wide band (UWB) techniques has risen. Although the signal from a single UWB device is very low, the energy absorption may increase significantly when many UWB devices are simultaneously adorned to a human body. An analysis method is therefore required from the point of view of biological safety evaluation. In this study, two approaches, one is in the time domain and the other is in the frequency domain, are proposed for the specific energy absorption (SA) and the specific absorption rate (SAR) calculation. It is shown that the two approaches have the same accuracy but the time-domain approach is more straightforward in the numerical analysis. By using the time-domain approach, SA and SAR calculation results are given for multiple UWB pulse exposure to an anatomical human body model under the Federal Communications Commission (FCC) UWB limit.
Naohiro KAWABATA Hisao KOGA Osamu MUTA Yoshihiko AKAIWA
As a method to realize a high-speed communication in the home network, the power-line communication (PLC) technique is known. A problem of PLC is that leakage radiation interferes with existing systems. When OFDM is used in a PLC system, the leakage radiation is not sufficiently reduced, even if the subcarriers corresponding to the frequency-band of the existing system are never used, because the signal is not strictly band-limited. To solve this problem, each subcarrier must be band-limited. In this paper, we apply the OQAM based multi-carrier transmission (OQAM-MCT) to a high-speed PLC system, where each subcarrier is individually band-limited. We also propose a pilot-symbol sequence suitable for frequency offset estimation, symbol-timing detection and channel estimation in the OQAM-MCT system. In this method, the pilot signal-sequence consists of a repeated series of the same data symbol. With this method, the pilot sequence approximately becomes equivalent to OFDM sequence and therefore existing pilot-assisted methods for OFDM are also applicable to OQAM-MCT system. Computer simulation results show that the OQAM-MCT system achieves both good transmission rate performance and low out-of-band radiation in PLC channels. It is also shown that the proposed pilot-sequence improves frequency offset estimation, symbol-timing detection and channel estimation performance as compared with the case of using pseudo-noise sequence.
We present a novel frequency partitioning technique of fractional frequency reuse (FFR) that reduces the effect of co-channel interference and increases the capacity of OFDM systems. The usable sub-channel sets are classified into the common sub-channel sets for all cells and the dedicated sub-channel sets for specific cell types in FFR. The proposed fractional frequency reuse with ordering scheme (FFRO) can decrease the amount of interference in the common sub-channel sets by specially designing the sub-channel sets and the order of sub-channel assignment for specific cell types. Simulation results show that the proposed FFRO yields enhanced performance for both uniform and non-uniform distributions of traffic load.
Wooram LEE Gunhaeng HEO Kwanho YOU
The heterodyne laser interferometer acts as an ultra-precise measurement apparatus in semiconductor manufacture. However the periodical nonlinearity property caused from frequency cross-talk is an obstacle to improve the high measurement accuracy in nanometer scale. In order to minimize the nonlinearity error of the heterodyne interferometer, we propose a frequency cross-talk compensation algorithm using an artificial intelligence method. The feedforward neural network trained by back-propagation compensates the nonlinearity error and regulates to minimize the difference with the reference signal. With some experimental results, the improved accuracy is proved through comparison with the position value from a capacitive displacement sensor.
Kamya Yekeh YAZDANDOOST Ryuji KOHNO
The medical care day by day and more and more is associated with and reliant upon concepts and advances of electronics and electromagnetics. Numerous medical devices are implanted in the body for medical use. Tissue implanted devices are of great interest for wireless medical applications due to the promising of different clinical usage to promote a patient independence. It can be used in hospitals, health care facilities and home to transmit patient measurement data, such as pulse and respiration rates to a nearby receiver, permitting greater patient mobility and increased comfort. As this service permits remote monitoring of several patients simultaneously it could also potentially decrease health care costs. Advancement in radio frequency communications and miniaturization of bioelectronics are supporting medical implant applications. A central component of wireless implanted device is an antenna and there are several issues to consider when designing an in-body antenna, including power consumption, size, frequency, biocompatibility and the unique RF transmission challenges posed by the human body. The radiation characteristics of such devices are important in terms of both safety and performance. The implanted antenna and human body as a medium for wireless communication are discussed over Medical Implant Communications Service (MICS) band in the frequency range of 402-405 MHz.
A high-efficiency CMOS rectifier circuit for UHF RFID applications was developed. The rectifier utilizes a self-Vth-cancellation (SVC) scheme in which the threshold voltage of MOSFETs is cancelled by applying gate bias voltage generated from the output voltage of the rectifier itself. A very simple circuit configuration and zero power dissipation characteristics in biasing enable excellent power conversion efficiency (PCE), especially under small RF input power conditions. At higher RF input power conditions, the PCE of the rectifier automatically decreases. This is the built-in self-power-regulation function. The proposed SVC CMOS rectifier was fabricated with a 0.35-µm CMOS process and the measured performance was compared with those of conventional nMOS, pMOS, and CMOS rectifiers and other types of Vth cancellation rectifiers as well. The SVC CMOS rectifier achieves 32% of PCE at the -10 dBm RF input power condition. This PCE is larger than rectifiers reported to date under this condition.
Taegeun OH Sanghoon LEE Gye-Tae GIL
A cell planning and resource allocation scheme called EBRD (Enhanced Bandwidth and Region Division) is presented for improving channel capacity and for maintaining a proper QoS (Quality of Service) over the downlink OFDMA (Orthogonal Frequency Division Multiple Access) system. Through an optimal combination of sectorization and frequency overlay, the EBRD scheme improves both channel capacity and outage probability. In order to analyze the performance of the proposed algorithm, the outage probability is obtained as a closed numerical form. In the simulation, the EBRD scheme outperforms 3-sectorization in terms of throughput and outage probability.
Young-Hwan YOU Sung-Jin KANG Hyoung-Kyu SONG
This letter proposes a computationally efficient way of jointly estimating the residual frequency offset (RFO) and sampling frequency offset (SFO) by using a continual pilot (CP) defined in OFDM-based DVB-T system. In order to devise an unbiased joint frequency estimator in the current DVB-T system, a CP subset is selected to offset the effects of RFO and SFO simultaneously.
Keiji GOTO Toru KAWANO Toyohiko ISHIHARA
We study the high-frequency asymptotic analysis methods for the scattered fields by a cylindrically curved conducting surface excited by the incident wave on the curved surface from the convex side. We first derive the novel hybrid ray-mode solution for the scattered fields near the concave surface by solving a canonical problem formulated under the assumption that the cylindrically curved conducting surface possesses only one edge. Then by applying the ray tracing technique and the idea of Keller's GTD (Geometrical Theory of Diffraction), the solutions derived for the canonical problem are extended to account for the problem of the radiation from and the scattering by the other edge of the cylindrically curved surface. We confirm the validity of the novel asymptotic representations proposed in the present study by comparing both with the numerical results obtained from the method of moment and the experimental results performed in the anechoic chamber.
Chen CHI Yu ZHANG Zhixing YANG
Software defined radio (SDR) technology has been widely applied for its powerful universality and flexibility in the past decade. To address the issue of bandpass sampling of multiband signals, a novel and efficient method of finding the minimum valid sampling frequency is proposed. Since there are frequency deviations due to the channel effect and hardware instability in actual systems, we also consider the guard-bands between downconverted signal spectra in determining the minimum sampling frequency. In addition, the case that the spectra within the sampled bandwidth are located in inverse placement can be avoided by our proposed method, which will reduce the complexity of the succeeding digital signal process significantly. Simulation results illustrate that the proper minimum sampling frequency can be determined rapidly and accurately.
Young-Hwan YOU Sung-Jin KANG Hyoung-Kyu SONG
In this letter, we suggest a simple way of implementing a post-FFT pilot-assisted sampling frequency offset and residual frequency offset estimator with reduced complexity in an orthogonal frequency division multiplexing (OFDM) system. In order to devise the low-complexity post-FFT frequency estimator, some modifications on the conventional estimator are highlighted with an emphasis on the selection of pilot subset.
We propose Adaptive Resource Allocation for the Partial Block MC-CDMA (ARA-PB/MC-CDMA) system. The ARA-PB/MC-CDMA system aims to improve total throughput performance and frequency efficiency across various channel conditions. It adaptively changes the number of blocks to improve the throughput performance and frequency efficiency according to the Signal to Interference Ratio (SIR). Therefore, the proposed system supports various Quality of Service (QoS) requirements for various SIR values.
Ruey-Shun CHEN Yung-Shun TSAI Arthur TU
In this study we propose a manufacturing control framework based on radio-frequency identification (RFID) technology and a distributed information system to construct a mass-customization production process in a loosely coupled shop-floor control environment. On the basis of this framework, we developed RFID middleware and an integrated information system for tracking and controlling the manufacturing process flow. A bicycle manufacturer was used to demonstrate the prototype system. The findings of this study were that the proposed framework can improve the visibility and traceability of the manufacturing process as well as enhance process quality control and real-time production pedigree access. Using this framework, an enterprise can easily integrate an RFID-based system into its manufacturing environment to facilitate mass customization and a just-in-time production model.
Kihun CHANG Sang il KWAK Young Joong YOON
In this paper, active frequency selective surfaces (FSS) having a squared aperture with a metal plate loading are described. Active FSS elements using switched PIN diodes are discussed with an equivalent circuit model. A unit cell consists of a square aperture element with metal island loading and one PIN diode placed at the upper gap, considering the vertical polarization. The electromagnetic properties of the active FSS structure are changed by applying dc bias to the substrate, and they can be estimated by the equivalent circuit model of the FSS structure and PIN diode. This active FSS design enables transmission to be switched on or off at 2.3 GHz, providing high transmission when the diodes are in an off state and high isolation when the diodes are on. The equivalent circuit model in the structure is investigated by analyzing transmission and reflection spectra. Measurements on active FSS are compared with numerical calculations. The experimentally observed frequency responses are also scrutinized.
Xin CHEN Jun YANG Long-xing SHI
A novel fast lock-in digitally controlled phase-locked loop (DCPLL) is proposed in this letter. This DCPLL adopts a novel frequency search algorithm to reduce the lock-in time. Furthermore, to reduce the power consumption, the frequency divider is reused as a frequency detector during the frequency acquisition, and reused as a time-to-digital converter module during the phase acquisition. To verify the proposed algorithm and architecture, a DCPLL design is implemented by SMIC 0.18 µm 1P6M CMOS technology. The Spice simulation results show that the DCPLL can achieve frequency acquisition in 3 reference cycles and complete phase acquisition in 11 reference cycles when locking to 200 MHz. The corresponding power consumption of DCPLL is 3.71 mW.
Since an FFT-based speech encryption system retains a considerable residual intelligibility, such as talk spurts and the original intonation in the encrypted speech, this makes it easy for eavesdroppers to deduce the information contents from the encrypted speech. In this letter, we propose a new technique based on the combination of an orthogonal frequency division multiplexing (OFDM) scheme and an appropriate QAM mapping method to remove the residual intelligibility from the encrypted speech by permuting several frequency components. In addition, the proposed OFDM-based speech encryption system needs only two FFT operations instead of the four required by the FFT-based speech encryption system. Simulation results are presented to show the effectiveness of this proposed technique.
Kyoya TAKANO Mizuki MOTOYOSHI Minoru FUJISHIMA
To realize low-power wireless transceivers, it is necessary to improve the performance of frequency synthesizers, which are typically frequency multipliers composed of a phase-locked loop (PLL). However, PLLs generally consume a large amount of power and occupy a large area. To improve the frequency multiplier, we propose a pulse-injection-locked frequency multiplier (PILFM), where a spurious signal is suppressed using a pulse input signal. An injection-locked oscillator (ILO) in a PILFM was fabricated by a 0.18 µm 1P5M CMOS process. The core size is 10.8 µm10.5 µm. The power consumption of the ILO is 9.6 µW at 250 MHz, 255 µW at 2.4 GHz and 1.47 mW at 4.8 GHz. The phase noise is -105 dBc/Hz at a 1 MHz offset.
Masatsugu HIGASHINAKA Hiroshi KUBO Akihiro OKAZAKI Yasutaka OGAWA Takeo OHGANE Toshihiko NISHIMURA
This paper proposes a novel channel estimation method for iterative equalization in MIMO systems. The proposed method incorporates co-channel interference (CCI) cancellation in the channel estimator and the channel estimation is successively performed with respect to each stream. Accuracy of channel estimation holds the key to be successfully converged the iterative equalization and decoding process. Although the channel estimates can be re-estimated by means of LS (Least Square) channel estimation using tentative decisions obtained in the iterative process, its performance is severely limited in a MIMO system because of erroneous decisions and ill-conditioned channel estimation matrix. The proposed method can suppress the above effects by means of CCI cancellation and successive channel estimation. Computer simulation confirms that the proposed channel estimation method can accurately estimate the channel, and the receiver with iterative equalization and the proposed method achieves excellent decoding performance in a MIMO-SM system.