Aiming at the problem of low classification accuracy of surface defects of lithium battery pole pieces by traditional classification methods, an image classification algorithm for surface defects of lithium battery pole piece based on deep learning is proposed in this paper. Firstly, Wavelet Threshold and Histogram Equalization are used to preprocess the detect image to weaken influence of noise in non-defect regions and enhance defect features. Secondly, a VGG-InceptionV2 network with better performance is proposed by adding InceptionV2 structure to the improved VGG network structure. Then the original data set is expanded by rotating, flipping and contrast adjustment, and the optimal value of the model hyperparameters is determined by experiments. Finally, the model in this paper is compared with VGG16 and GoogLeNet to realize the recognition of defect types. The results show that the accuracy rate of the model in this paper for the surface pole piece defects of lithium batteries is 98.75%, and the model parameters is only 1.7M, which has certain significance for the classification of lithium battery surface pole piece defects in industry.

Triboelectric generators have been attracting much attention as electrical power sources in scientific communities and industries. Based on dielectric physics, two microscopic routes are available as current sources: One is charge displacement and the other is dipolar rotation. We have been investigating these routes as power sources for triboelectric generation. In other words, dipolar energy transfer process during a course of depolarization has the potentiality to be utilized as triboelectric generator. In this paper, we show that polyimide polymer film with permanent dipoles, i.e., PMDA-ODA polyimide, can provide current source capacity enhanced at elevated temperature, which is in good agreement with our idea based on dipolar energy mode of triboelectric generator. That is, permanent dipoles rotate quickly at elevated temperature, and act as an enhanced current source in the dipolar energy source model of triboelectric generator.

Optical phase conjugation (OPC) is an all-optical signal processing technique for mitigating fiber nonlinearity and is promising for building cost-efficient fiber networks with few optic-electric-optic conversions and long amplification spacing. In lumped amplified systems, OPC has a little nonlinearity mitigation efficiency for nonlinear distortion induced by cross-phase modulation (XPM) due to the asymmetry of power and chromatic dispersion (CD) maps during propagation in transmission fiber. In addition, the walk-off of XPM-induced noise becomes small due to the CD compensation effect of OPC, so the deterministic nonlinear distortion increases. Therefore, lumped amplified transmission systems with OPC are more sensitive to channel spacing than conventional systems. In this paper, we show the channel spacing dependence of NZ-DSF transmission using amplification repeater with OPC. Numerical simulations show comprehensive characteristics between channel spacing and CD in a 100-Gbps/λ WDM signal. An experimental verification using periodically poled LiNbO3-based OPC is also performed. These results suggest that channel spacing design is more important in OPC-assisted systems than in conventional dispersion-unmanaged systems.

Platform-mounted small antennas increase dielectric loss and conductive loss and decrease the radiation efficiency. This paper proposes a novel antenna design method to improve radiation efficiency for platform-mounted small antennas by characteristic mode analysis. The proposed method uses mapping of modal weighting coefficient (MWC) and infinitesimal dipole and evaluate the metal casing with 100mm × 55mm × 23mm as a platform excited by an inverted-F antenna. The simulation and measurement results show that the radiation efficiency of 5% is improved with the whole system from 2.5% of the single antenna.

To achieve smooth beam injection in operation of synchrotron radiation facilities, pulsed multipole magnet beam injectors are developed. It is found that the developed beam injector causes serious disturbance in the circulating storage beam in the Aichi synchrotron radiation center, and that such the unexpected disturbance of the storage beam may be caused by eddy current induced on thin titanium coating inside a beam duct. In this work, the induced eddy current on the titanium layer is evaluated quantitatively by numerical simulations and improvement for the developed beam injector is discussed based on the numerical simulation.

We evaluated the noise properties of a periodically poled lithium niobite phase-sensitive amplifier (PSA) using a phase-locked local oscillator as a pump generated by an optical phase-locked loop (OPLL-LO). To examine whether or not the LO pump generated by an OPLL degrades the noise figure (NF) of the PSA, we compared the noise levels of a PSA using an OPLL-LO with that of one using a master local oscillator (M-LO) that utilizes the master light itself as a pump in the electrical domain. With the OPLL, the phase-locked local light had almost the same frequency noise components as the master light. We observed almost the same output noise spectra for the OPLL-LO PSA and M-LO PSA and confirmed the absence of excess noise components in the OPLL-LO PSA in the 0.1 to 20-GHz range. The OPLL-LO PSA exhibited low-noise amplification with an average NF of 1.7-dB at a 23.2-dB gain within an input power range of -31 to -21dBm, which is a feasible input power for repeater amplifiers used in the optical signal transmission systems. We also investigated the influence of the noisy master light, which emulates the accumulation of optical noise from the amplifiers in the transmission system. The OPLL-LO PSA was highly tolerant to the optical noise because the difference in the NF was negligibly small within a master light OSNR range of 5 to 55dB. These results indicate that the OPLL-LO PSA will be useful as a low-noise repeater amplifier for the spectrally efficient large-capacity photonic networks of the future.

We developed a polarization-independent and reserved-band-less complementary spectral inverted optical phase conjugation (CSI-OPC) device using dual-band difference frequency generation based on highly efficient periodically poled LiNbO3 waveguide technologies. To examine the nonlinearity mitigation in a long-haul transmission using a large number of OPCs, we installed a CSI-OPC device in the middle of a pure silica core fiber-based recirculating loop transmission line with a length of 320km. First, we examined the fiber-input power tolerance after 5,120-km and 6,400-km transmission using 22.5-Gbaud PDM-16QAM 10-channel DWDM signals and found a Q-factor improvement of over 1.3dB along with enhanced power tolerance thanks to mitigating the fiber nonlinearity. We then demonstrated transmission distance extension using the CSI-OPC device. The use of multiple CSI-OPCs enables an obvious performance improvements attained by extending the transmission distance from 6,400km to 8,960km, which corresponds to applying the CSI-OPC device 28 times. Moreover, there was no Q-factor degradation for the link in a linear regime after applying the CSI-OPC device more than 16 times. These results demonstrate that the CSI-OPC device can improve the nonlinear tolerance of PDM-16QAM signals without an excess penalty.

A low frequency electric field probe that integrates data acquisition and storage is developed in this paper. An electric small monopole antenna printed on the circuit board is used as the receiving antenna; the rear end of the monopole antenna is connected to the integral circuit to achieve the flat frequency response; the logarithmic detection method is applied to obtain a high measurement dynamic range. In addition, a Microprogrammed Control Unit is set inside to realize data acquisition and storage. The size of the probe developed is not exceeding 20 mm × 20 mm × 30 mm. The field strength 0.2 V/m ~ 261 V/m can be measured in the frequency range of 500 Hz ~ 10 MHz, achieving a dynamic range over 62 dB. It is suitable for low frequency electric field strength measurement and shielding effectiveness test of small shield.

This paper deals with the problem of minimizing roundoff noise and pole sensitivity simultaneously subject to l2-scaling constraints for state-space digital filters. A novel measure for evaluating roundoff noise and pole sensitivity is proposed, and an efficient technique for minimizing this measure by jointly optimizing state-space realization and error feedback is explored, namely, the constrained optimization problem at hand is converted into an unconstrained problem and then the resultant problem is solved by employing a quasi-Newton algorithm. A numerical example is presented to demonstrate the validity and effectiveness of the proposed technique.

In order to achieve an antenna with robustness to metal for closed space wireless communications, two types of the folded monopole antenna with different input impedance have been studied. In this study, we propose the folded monopole antenna, which can switch the input impedance by a simple method. Both simulated and measured results show that the proposed antenna can improve robustness to the proximity of the metal.

This paper proposes a low-profile unidirectional supergain antenna applicable to wireless communication devices such as mobile terminals, the Internet of Things and so on. The antennas used for such systems are required to be not only electrically low-profile but also unsusceptible to surrounding objects such as human body and/or electrical equipment. The proposed antenna achieves both requirements due to its supergain property using planar elements and a closely placed planar reflector. The primary antenna is an asymmetric dipole type, and consists of a monopole element mounted on an edge of a rectangular conducting plane. Both elements are placed on a dielectric substrate backed by the planar reflector. It is numerically and experimentally shown that the supergain property is achieved by optimizing the geometrical parameters of the antenna. It is also shown that the impedance characteristics can be successfully adjusted by changing the lengths of the ground plane element and the monopole element. Thus, no additional impedance matching circuit is necessary. Furthermore, it is shown that surrounding objects have insignificant impact on the antenna performance.

Differential microphone arrays have been widely used in hands-free communication systems because of their frequency-invariant beampatterns, high directivity factors and small apertures. Considering the position of acoustic source always moving within a certain range in real application, this letter proposes an approach to construct the steerable first-order differential beampattern by using four omnidirectional microphones arranged in a non-orthogonal circular geometry. The theoretical analysis and simulation results show beampattern constructed via this method achieves the same direction factor (DF) as traditional DMAs and higher white noise gain (WNG) within a certain angular range. The simulation results also show the proposed method applies to processing speech signal. In experiments, we show the effectiveness and small computation amount of the proposed method.

This paper improves radiation patterns and impedance matching of a broadband sleeve dipole antenna. A broadband sleeve dipole antenna is designed and the effect of the structure parameters on the |S11| characteristics is calculated. Current distributions of the resonance frequencies are calculated. A broadband sleeve dipole antenna with plate element is proposed. Better impedance matching is obtained by adjusting the size of the plate element. The nulls of the radiation patterns are reduced at high frequencies and the gain in the horizontal direction is improved.

To design antennas for ingestible capsule endoscope systems, the transmission factors of dipole and loop antennas placed in the torso-shaped phantom filled with deionized water or human body equivalent liquid (HBEL) are investigated by numerical and experimental study. The S-parameter method is used to evaluate transmission characteristics through a torso-shaped phantom in a broadband frequency range. Good agreement of S-parameters between measured results and numerical analysis is observed and the transmission factors for both cases are obtained. Comparison of the transmission factors between HBEL and deionized water is presented to explain the relation between conductivity and the transmission characteristics. Two types of antennas, dipole antenna and loop antenna are compared. In the case of a dipole antenna placed in deionized water, it is observed that the transmission factor decreases as conductivity increases. On the other hand, there is a local maximum in the transmission factor at 675 MHz in the case of HBEL. This phenomenon is not observed in the case of a loop antenna. The transmission factor of capsule dipole antenna and capsule loop antenna are compared and the guideline in designing capsule antennas by using transmission factor is also proposed.

This study mainly involved examining a high-directivity radiation system with spherical dielectric resonator as pseudo multipole source. The method of spherical wave expansion is focused on wherein the plane wave that is infinitely spread can be radiated from or absorbed by multipoles at the origin. It is not possible to explain this phenomenon by Huygens' principle, which is a basic principle of aperture antenna theory. Thus, in the study, a high-directivity beam design is proposed by synthesizing spherical waves. The directivity of the synthesized spherical wave corresponds with the angular momentum and angle, which is an uncertainty relation different from that of the aperture source. The estimation of the effective aperture of the synthesized spherical wave indicates that the wave intrinsic source is assumed to exist at the surface of the cutoff region. Finally, the results reveal that a radiation system without a singular point can be composed using a spherical dielectric resonator. The study discusses the potential of a high-directivity radiation system constructed by a multi-mode degenerate spherical dielectric resonator as a pseudo multipole source.

In this paper, a printed elliptical monopole antenna for wideband circular polarization is proposed. The antenna's structure is asymmetric with regard to the microstrip line. The section of the ground plane that overlaps the elliptical patch is removed. With simulations, the relationship between the antenna's geometrical parameters and the antenna's axial ratio of circularly polarized wave is clarified. The operational principle for wideband circular polarization is explained by the simulated electric current distributions. The simulated and measured bandwidths of the 3dB-axial ratio with a 2-VSWR is approximately 88.4% (2.12GHz-5.47GHz) and 83.6% (2.20GHz-5.36GHz), respectively.

This paper proposes an opamp-free solution to implement single-phase-clock controlled noise shaping in a SAR ADC. Unlike a conventional noise shaping SAR ADC, the proposal realizes noise shaping by charge redistribution, which is a passive technique. The passive implementation has high power efficiency. Meanwhile, since the proposal maintains the basic architecture and operation method of a traditional SAR ADC, it retains all the advantages of a SAR ADC. Furthermore, noise shaping helps to improve the performance of SAR ADC and relaxes its non-ideal effects. Designed in a 65-nm CMOS technology, the prototype realizes 58-dB SNDR based on an 8-bit C-DAC at 50-MS/s sampling frequency. It consumes 120.7-µW power from a 0.8-V supply and achieves a FoM of 14.8-fJ per conversion step.

We propose a highly sensitive carrier-recovery system for in-line amplification for binary phase shift keying (BPSK) signals in a periodically poled LiNbO3 based phase sensitive amplifier (PSA). We applied a discrete two-stage second harmonic generation/difference frequency generation (SHG/DFG) parametric conversion scheme to enhance the sensitivity of the carrier recovery. Owing to this two-stage SHG/DFG scheme, the conversion efficiency of the seed light for the injection locking needed for the pump generation can be improved compared to that of the cascaded SHG/DFG scheme. The new discrete scheme might also prevent the SNR degradation of the seed light caused by the ASE from the booster EDFA compared with the previous system that used the cascaded scheme. This novel carrier-recovery system exhibits high sensitivity with the SNR of over 7.8dB of the seed light, while tapped signal power is as low as -50dBm, which is low enough for injection locking. The new in-line PSA with this carrier-recovery system exhibits high gain of over 11dB. Since we successfully obtained the high gain property, we tried multistage amplification taking into account practical use and achieved it with both a high gain of 20dB and a noise figure that is almost as low as the standard quantum limit of a PSA.

A frequency-reconfigurable dipole antenna, whose dual resonant frequencies are independently controlled, is introduced. The antenna's conductor consists of radiating conductors, lumped and distributed elements, and varactors. To design the antenna, current distribution, input impedance, and radiation power including higher-order modes, are analyzed for a narrow-angle sectorial antenna embedded with passive elements. To derive the formulae used, radiation power is analyzed in two ways: using Chu's equivalent circuit and the multipole expansion method. Numerical estimations of electrically small antennas show that dual-band antennas are feasible. The dual resonant frequencies are controlled with the embedded series and shunt inductors. A dual-band antenna is fabricated, and measured input impedances agree well with the calculated data. With the configuration, an electrically small 2.5-/5-GHz dual-band reconfig-urable antenna is designed and fabricated, where the reactance values for the series and shunt inductors are controlled with varactors, each connected in series to the inductors. Varying the voltages applied to the varactors varies the measured upper and lower resonant frequencies between 2.6 and 2.9GHz and between 5.1 and 5.3GHz, where the other resonant frequency is kept almost identical. Measured radiation patterns on the H-plane are almost omni-directional for both bands.

A novel circularly and linearly polarized loop antenna is presented. A simple loop configuration, twisted like a cross shape, has achieved radiating wide beam circular polarization simultaneously with linear polarization in two close bands. This cross configuration brings good circular polarization to a loop antenna because it uses the transmission line mode of a folded dipole antenna. For these reasons, the antenna is named the Cross Spiral Antenna (CSA). In this paper, a basic structure and the principle of the CSA radiating circular polarization with one port feeding is explained. The prototype CSA, which is tuned to around 1.57GHz and 1.6GHz, is tested for verifying the effectiveness of the suggested antenna configuration.