In this paper, we present a differential dual-modulus prescaler based on an injection-locked frequency divider (ILFD) for satellite low-noise block (LNB) down-converters. We fabricated three-stage differential latches using an ILFD and a cascaded differential divider in a 130-nm CMOS process. The prototype chip core area occupies 40µm × 20µm. The proposed prescaler achieved the locking range of 2.1-10GHz with both divide-by-10 and divide-by-11 operations at a supply voltage of 1.4V. Normalized energy consumptions are 0.4pJ (=mW/GHz) at a 1.4-V supply voltage and 0.24pJ at a 1.2-V supply voltage. To evaluate the tolerance of phase-difference deviation of the input differential pair from the perfect differential phase-difference, 180 degrees, we measured the operational frequencies for various phase-difference inputs. The proposed prescaler achieved the operational frequency range of 2.1-10GHz with an input phase-difference deviation of less than 90 degrees. However, the range of operational frequency decreases as the phase-difference deviation increases beyond 90 degrees and reaches 3.9-7.9GHz for the phase-difference deviation of 180 degrees (i.e. no phase difference). In addition, to confirm the fully locking operation, we measured the spurious noise and the phase noise degradation while reducing the supply voltage. The sensitivity analysis of the prescaler for various supply voltages can explain the above degradation of spectral purity. Spurious noise arises and the phase noise degrades with decreasing supply voltage due to the quasi- and non-locking operations. We verified the fully-locking operation for the LNB down-converter at a 1.4-V supply voltage.

This paper shows a new pulse swallow programmable frequency divider with the division step size of 0.5. To realize the division step size of 0.5 by a conventional pulse swallow method, we propose a parallel dual modulus prescaler with the division ratio of P and P + 0.5. It consists of simple circuit elements and has an advantage over the conventional dual modulus prescaler with the division step size of 0.5 in high frequency operation. The proposed parallel dual modulus prescaler with the division ratio 8 and 8.5 is implemented in the 0.13-µm CMOS technology. The proposed architecture achieves 7 times higher frequency operation than the conventional one theoretically. It is verified the functions over 5 GHz.

The operating speed scalability is demonstrated by using the forward body biasing method for a 1-V 0.18-µm CMOS true single-phase clocking (TSPC) dual-modulus prescaler. With the forward body bias voltage varying between 0 and 0.4 V, the maximum operating speed changes by about 40–50% and the maximum input sensitivity frequency changes by about 400%. This speed scalability is achieved with less than 0.5-dB phase noise degradation. This demonstration indicates that the forward body biasing method is instrumental to build a cost-saving power-efficient 1-V 0.18-µm CMOS radio for low-power WBAN and WSN applications.

This paper presents a single-chip RF tuner/OFDM demodulator for a mobile digital TV application called “1-segment broadcasting.” To achieve required performances for the single-chip receiver, a tunable technique for a low-noise amplifier (LNA) and spurious suppression techniques are proposed in this paper. Firstly, to receive all channels from 470 MHz to 770 MHz and to relax distortion characteristics of following circuit blocks such as an RF variable-gain amplifier and a mixer, a tunable technique for the LNA is proposed. Then, to improve the sensitivity, spurious signal suppression techniques are also proposed. The single-chip receiver using the proposed techniques is fabricated in 90 nm CMOS technology and total die size is 3.26 mm 3.26 mm. Using the tunable LNA and suppressing undesired spurious signals, the sensitivities of less than -98.6 dBm are achieved for all the channels.

A 1.8 V, 5 GHz low power frequency synthesizer for Wireless Sensor Networks is presented in 0.18 µm CMOS technology. A low power phase-switching prescaler is designed, and the current mode phase rotator is merged into the first divide-by-2 circuit of the prescaler to reduce power and propagation delay. An improved charge pump circuit is proposed to compensate for the dynamic effects with the charge pump. By a divide-by-2 circuit, the frequency synthesizer can provide a 2.324-2.714 GHz quadrature output frequency in 1 MHz steps with a 4 MHz reference frequency. The measured output phase noise is -110 dBc/Hz at 1-MHz offset frequency. The power consumption of the PLL is 11.2 mW at 1.8 V supply voltage.

A high-speed and ultra-low-voltage divide-by-4/5 counter with dynamic floating input D flip-flop (DFIDFF) is presented in this paper. The proposed DFIDFF and control logic gates are merged to reduce effective capacitance of internal and external nodes, and increase the operating speed of divide-by-4/5 counter. The proposed divide-by-4/5 counter is fabricated in a 0.13-µm CMOS process. The measured maximum operating frequency and power consumption of the counter are 600 MHz and 8.35 µW at a 0.5 V supply voltage. HSPICE simulations demonstrate that the proposed counter (divide-by-4) reduces power-delay product (PDP) by 37%, 71%, and 57% from those of the TGFF counter, Yang's counter [1], and the E-TSPC counter [2], respectively.

Four 50% duty-cycle divide-by-3 prescalers--positively/ negatively triggered sample-sample-hold (SSH) and sample-hold-hold (SHH) prescalers--are designed based on the current switchable D flip-flops and discussed in this paper. The positively triggered SSH and SHH prescalers are fabricated using the 0.35-µm SiGe BiCMOS technology and measured by the real-time oscilloscope and the spectrum analyzer. The SHH prescaler is our proposed structure and demonstrated in this paper. According to the measurement results, under the condition of the same input power, its maximum operation frequency is twice as high as that of the SSH prescaler thanks to better signal synchronization. At 2.7 V supply, the SSH prescaler operates from 500 MHz to 2 GHz as the SHH prescaler performs from 1 GHz to 3.4 GHz. The input sensitivity level of both structures is about -5 dBm, while the maximum output power is also about -5 dBm. The core current consumption is 4.538 mA and 4.258 mA for the SSH and SHH prescalers, respectively.

A dual-modulus (divide-by-128/129) prescaler has been designed based on 0.25-µm CMOS technology employing new D-flip-flops. The new D-flip-flops are free from glitch problems due to internal charge sharing. Transistor merging technique has been employed to reduce the number of transistors and to secure reliable high-speed operation. At the 2.5-V supply voltage, the prescaler using the proposed dynamic D-flip-flops can operate up to the frequency of 2.95-GHz, and consumes about 10% and about 27% less power than Yuan/Svensson's and Huang's circuits, respectively.

In the phase locked loop (PLL) frequency synthesizer which is used in a higher frequency region, the prescaler method is employed in order to increase the operating frequency of the programmable divider. However, since the fixed divider whose division ratio is same as the prescaler is installed at the following stage of the reference divider, the reference frequency is decreased and the performance of the PLL frequency synthesizer is degraded. The prescaler PLL frequency synthesizer using multi-programmable divider is one of the counter measures answering the request. In this paper we propose the reduction of the number of programmable dividers by using the (N+1/2) programmable divider. The effectiveness of the proposed method is confirmed by experimental results.

This paper describes a flip-flop circuit using a directly controlled emitter-follower with a diode-feedback level stabilizer (DC-DF) and a resistor-feedback level stabilizer (DC-RF) for low-power multi-GHz prescalers. The new flip-flop circuit reduces the emitter-follower current and gains both high-frequency operation and low-power. A dual modulus (4/5) prescaler using this circuit technology was fabricated with a 0.35 µm BiCMOS process. The current draw of the prescaler using the DC-RF is 34% smaller than conventional LCML circuits. The DC-RF prescaler operates at 2.11 GHz with a total current consumption of 1.03 mA. In addition, the circuit operates with a supply voltage of down to 2.4 V by using the resistor level-shift clock-driver.

In this paper, in order to achieve the low power consumption of programmable divider in a PLL frequency synthesizer, we propose a new prescaler method for low power consumption. A fixed prescaler is inserted in front of the (N +1/2) programmable divider which is designed based on the new principle. The divider ratio in the loop does not vary at all even if such a prescaler is utilized. Then the permissible delay periods of a programmable divider can be extended to two times as long as the conventional method, and the low power consumption and low cost in a PLL frequency synthesizer have been achieved.

High frequency and low power 128/129 dual modulus prescaler ICs are developed for mobile communication applications, using 0.5 µm GaAs MESFET technology. Provided with an on-chip voltage regulator, a prescaler IC with an input amplifier operates in a wide frequency range from 200 MHz to 1,500 MHz at input power from -15 dBm to +17 dBm at the temperature of -30 to +120 with supply voltage of 2.7 V, 3.0 V and 5.0 V. At the same time, it demonstrated its low power characteristics consuming 3.68 mA with 3.0 V at +30 in operation, 0.16 mA while powered-off. Another prescaler IC without an input amplifier operates up to 1,650 MHz with Vdd=2.7 V, 3.0 V and 5.0 V at +30, dissipating 2.74 mA/3.0 V.