This paper deals with the scattering of a transverse magnetic (TM) plane wave from a perfectly conductive sinusoidal surface with finite extent. By use of the undersampling approximation and a rectangular pulse approximation, an asymptotic formula for the total scattering cross section at a low grazing limit of incident angle is obtained explicitly under conditions such that the surface is small in roughness and slope, and the corrugation width is sufficiently large. The formula shows that the total scattering cross section is proportional to the square root of the corrugation width but does not depend on the surface period and surface roughness. When the corrugation width is not large, however, the scattered wave can be obtained by a single scattering approximation, which gives the total scattering cross section proportional to the corrugation width and the Rayleigh slope parameter. From the asymptotic formula and the single scattering solution, a transition point is defined explicitly. By comparison with numerical results, it is concluded that the asymptotic formula is fairly accurate when the corrugation width is much larger than the transition point.

This paper deals with the scattering of a TM plane wave from a periodic grating with single defect, of which position is known. The surface is perfectly conductive and made up with a periodic array of rectangular grooves and a defect where a groove is not formed. The scattered wave above grooves is written as a variation from the diffracted wave for the perfectly periodic case. Then, an integral equation for the scattering amplitude is obtained, which is solved numerically by use of truncation and the iteration method. The differential scattering cross section and the optical theorem are calculated in terms of the scattering amplitude and are illustrated in figures. It is found that incoherent Wood's anomaly appears at critical angles of scattering. The physical mechanisms of Wood's anomaly and incoherent Wood's anomaly are discussed in relation to the guided surface wave excited by the incident plane wave. It is concluded that incoherent Wood's anomaly is caused by the diffraction of the guided surface wave.

This paper addresses a new surface reconstruction scheme for approximating the isosurface from a set of tomographic cross sectional images. Differently from the novel Marching Cubes (MC) algorithm, our method does not extract the iso-density surface (isosurface) directly from the voxel data but calculates the iso-density point (isopoint) first. After building a coarse initial mesh approximating the ideal isosurface by the cell-boundary representation, it metamorphoses the mesh into the final isosurface by a relaxation scheme, called shrink-wrapping process. Compared with the MC algorithm, our method is robust and does not make any cracks on surface. Furthermore, since it is possible to utilize lots of additional isopoints during the surface reconstruction process by extending the adjacency definition, theoretically the resulting surface can be better in quality than the MC algorithm. According to experiments, it is proved to be very robust and efficient for isosurface reconstruction from cross sectional images.

This paper addresses the ambiguity of radar altimetry related to the statistical nature of the Earth's surface roughness. A hypothetic altimetry method, which provides a simple way to quantify the measures of ambiguity, is proposed. Cramer-Rao lower bounds on the variances of estimates for the mean altitude and root-mean-square height of the sea surface are suggested as such quantitative measures. The accuracy of some types of air- and spaceborne radar altimeters is numerically analyzed against the derived lower bounds.

In order to realize a higher density version of the conventional optical disk, shorter wavelength laser and narrower track pitch have been put to practical use. However, using narrow track pitch can cause the increase of the crosstalk from the adjacent tracks. Moreover, the use of narrow pitch and short wavelength can also give rise to the increase of deterioration of the detected signal characteristics due to the microscopic roughness of disk surface. In this paper, in order to estimate the effect of surface roughness theoretically, we try to analyze the light-beam scattering and detected signal characteristics of a blue laser optical disk model with random rough surfaces by the Finite Difference Time Domain (FDTD) method.

Excitation of plasmons on the surface of a metal grating placed in planar or conical mounting is investigated in detail. Most of the results of numerical computations are compared with experimental data. When a TM wave illuminates a metal grating, total or partial absorption of incident light occurs at angles of incidence at which the plasmon surface waves are excited. In planar mounting the absorption is generally strong and nearly total absorption is observed. While in conical mounting, it is not so strong as that in the planar mounting case and a considerable amount of incident power is reflected. This, however, is accompanied by enhanced TM-TE mode conversion and the greater part of the reflected wave is in the TE polarization. The reciprocal of the TM-wave efficiency, hence, is a practical measure in finding the angles of incidence at which the plasmons are excited. Because the angles are sensitive functions of the refractive index of a material over the grating surface, this phenomenon can be used as an index sensor.

This letter proposes a new bandpass shielding enclosure (BPSE) for modern handheld communication devices. This enclosure is characterized by high transmittance at the specified wireless signal band and high shielding effectiveness (SE) outside this band. In addition, it has little influence on the impedance-matching bandwidth and antenna patterns of an internal antenna embedded inside the device. A prototype was created, simulated and measured. The simulated and measured results demonstrate the promising performance of this newly proposed shielding enclosure.

Accurate extraction of the trap position in the oxide in deep-submicron MOSFET by RTN measurement has been investigated both theoretically and experimentally. The conventional equation based on the ratio of emission time and capture time ignores two effects, that is, the poly gate depletion effect and surface potential variation in strong inversion regime. In this paper, by including both of the two effects, we have derived a new equation which gives us more accurate information of the trap depth from the interface and the trap energy. With experimental result, we compare the trap depth obtained from the new equation and that of the conventional method.

Acoustic field analysis results of surface acoustic wave dispersive delay lines using inclined chirp IDTs on a Y-Z LiNbO3 substrate are described. The calculated results are compared with optical measurements. The angular spectrum of the plane wave method is applied to calculation of the acoustic fields considering the anisotropy of the SAW velocity by using the polynomial approximation. Acoustic field propagating along the Z-axis of the substrate, which is the main beam excited by the inclined chirp IDT, shows asymmetric distribution between the +Z and -Z directions. Furthermore the SAW beam propagating in a slanted direction with an angle of +18 from the Z axis to the X-axis is observed. It is described that the SAW beam propagating in a slanted direction is the first side lobe excited by the inclined chirp IDT. The acoustic field shows asymmetric distribution along the X-axis because of the asymmetric structure of the inclined chirp IDT. Finally, acoustic field of a two-IDT connected structure which consists of the same IDTs electrically connected in series is presented. The acoustic field of the two-IDT connected structure is calculated to be superposed onto the calculated result of the acoustic field exited by one IDT on the calculated result shifted along the X-axis. Two SAW beams excited by IDTs are observed. The distributions of the SAW beams are not in parallel. The calculated results show good agreement with the optical measurement results.

The potential of optical circuit packaging technology is discussed. Special attention is paid to introduction of "optical wiring" at the printed wiring board level (i.e., in the "last 1 meter area") to overcome the bandwidth limitations of electrical copper-based wiring. The suitability of optical surface mount technology (O-SMT) as a possible solution is reviewed. It is shown that the key to the utility of O-SMT is high efficiency and alignment-free coupling between optical wiring and optical devices. O-SMT requires a method to change the beam direction from the horizontal to the vertical and vice versa in order to couple optical wiring in an OE-board and OE-devices mounted on the board. A novel method using an "optical pin" is proposed and investigated. Furthermore, an optical coupling method using a self-written waveguide called "optical solder" is reviewed. Several applications of self-written waveguides using a green laser and a photo-mask are demonstrated.

This paper deals with the scattering of transverse magnetic (TM) plane wave by a perfectly conductive surface made up of a periodic array of finite number of rectangular grooves. By the modal expansion method, the total scattering cross section pc is numerically calculated for several different numbers of grooves. It is then found that, when the groove depth is less than wavelenght, the total scattering cross section pc increases linearly proportional to the corrugation width W. But an exception takes place at a low grazing angle of incidence, where pc is proportional to Wα and the exponent α is less than 1. From these facts, it is concluded that the total scattering cross section pc must diverge but pc/W the total scattering cross section per unit surface must vanish at a low grazing limit when the number of grooves goes to infinity.

In this paper, we have derived the new solution for the medium-frequency and the high-frequency ground wave propagation in a surface duct over mixed-paths. We have shown newly that the solution for the ground wave propagation in a standard atmosphere can be obtained directly from the solution for the surface duct problem by applying the analytic continuation from the negative equivalent radius of curvature of the earth to the positive one. Through the theoretical and experimental studies, it is confirmed that the radio wave propagating over the sea in the land-to-sea mixed-paths is enhanced by the recovery effect. It is clarified that the ground wave is also enhanced in the surface duct in a long range propagation. It is shown that the unexpected attenuation and the anomalous variation with distance are appeared in the propagation in the urban area due to the emergence of the slow-wave type trapped surface wave.

An electrooptic near-field mapping system based on a gain-switched distributed feedback (DFB) pulsed laser and a CdTe electrooptic crystal was used for characterizing stationary and transient near-field patterns of conventional and uniplanar compact photonic band gap (UC-PBG) patch antennas. Effect of the UC-PBG structure on reduction in surface waves in the UC-PBG patch antenna was experimentally verified by comparing stationary and transient near-field measurement of the conventional and UC-PBG patch antennas.

When a cylindrically curved concave conducting surface is terminated abruptly at the edge, the whispering gallery (WG) mode propagating toward the edge direction is radiated into the free space from the aperture plane at the edge. In this paper, by applying the new analysis method, we shall derive a uniform geometrical theory of diffraction solution (UTD) for the electric-type WG mode radiation field applicable in the transition region near the geometrical boundaries produced by the incident modal ray on the edge of the curved surface. The UTD is represented by the summation of the solution for the geometrical ray converted from the modal ray of the WG mode and the solution for the uniform edge diffracted ray scattered at the cylindrically curved edge. By comparing with the reference solution obtained numerically from the integral representation of the radiation field, we will confirm the validity and the utility of the UTD proposed in this paper.

A waveguide-based surface plasmon resonance (SPR) sensor with an adsorbed layer is analyzed using the beam-propagation method. For two-dimensional (2-D) models, numerical results show that the change in thickness of the adsorbed layer placed on the metal leads to a significant shift of the maximum absorption wavelength. Through eigenmode analysis, the maximum absorption wavelength is found to be consistent with the cutoff wavelength of the second-order surface plasmon mode. The designed 2-D sensor shows an absorption wavelength shift from 0.595 to 0.603 µm, when the analyte refractive index is increased from 1.330 to 1.334. After a basic investigation using the 2-D models, we next study 3-D models. When the metal with the absorbed layer is wide enough to cover the core region, the 3-D results are similar to the 2-D results. However, as the metal width is reduced, the absorption wavelength shifts toward a shorter wavelength and the sensitivity to the refractive index change degrades gradually. The degradation of the sensitivity is considerable when the metal width is narrower than the core width. As a result, the metal width of the practical SPR sensor should be slightly wider than the core width so as to maintain the sensitivity corresponding to that obtained for the 2-D model.

Guiding and nanofocusing of a two-dimensional (2D) optical beam in a negative-dielectric-gap waveguide is studied theoretically. An index-guiding method along the dielectric core embedded in the negative-dielectric-gap is proposed and the confinement properties of the 2D optical beam are studied by the effective-refractive-index method and FDTD simulations. We have shown that the lateral beam width of the 2D optical beam can be shrunk to zero beyond the diffraction limit. A tapered negative-dielectric-gap waveguide using adiabatic propagation achieves nano-focusing and can be applied to nano-optical couplers. This is a gateway from conventional dielectric waveguides to nano-optical integrated circuits.

A lithium niobate (LiNbO3)/silicon (Si) hybrid structure has been developed by the surface-activated bonding of LiNbO3 chips with gold (Au) thin film to Si substrates with patterned Au film. After organic contaminants on the Au surfaces were removed using argon radio-frequency plasma, Au-to-Au bonding was carried out in ambient air. Strong bonding at significantly low temperatures below 100 without generating cracks has been demonstrated.

In this paper, we propose a new method for detecting label-free T4-DNA molecules quantitatively using a surface plasmon resonance (SPR) technique on a gold thin film. We used a solution that dissolved T4-DNA molecules in pure water, and examined the relationship between DNA concentration change and SPR angle change in the solution. As a result, it was confirmed that the SPR angle change increased with increasing DNA concentration change. Therefore, it was feasible to detect the DNA concentration change using the SPR technique. Furthermore, to examine and detect a single or a few DNA molecule, we tried to fabricate an SPR chip in which SPR area is narrowed so that it has the same effect as focusing the beam. To narrow the SPR area, we decreased the area of gold thin film in this chip, and, to reflect light from only the area of gold thin film, the area without a gold thin film was micromachined to increase its unevenness for the reduction of light reflection. By the above-mentioned method, we examined the possibility of detecting a label-free DNA molecule using the SPR technique.

Molecular aligned naphthacene thins films were fabricated using vacuum evaporation and the rubbing method. The attenuated total reflection (ATR) and emission light properties from surface plasmon (SP) excitation due to molecular luminescence were investigated for these films. The long axis of the rod-like molecule was estimated to align perpendicular to the rubbing direction. The ATR and emission light properties depended on the molecular orientation.

This paper studies the scattering of a TM plane wave from a perfectly conductive sinusoidal surface with finite extent by the small perturbation method. We obtain the first and second order perturbed solutions explicitly, in terms of which the differential scattering cross section and the total scattering cross section per unit surface are calculated and are illustrated in figures. By comparison with results by a numerical method, it is concluded that the perturbed solution is reasonable even for a critical angle of incidence if the surface is small in roughness and gentle in slope and if the corrugation width is less than certain value. A brief discussion is given on multiple scattering effects.