Active oxygen species (AOS), e.g., excited singlet oxygen atom [O(1D)], excited singlet oxygen molecules (1O2), ground-state oxygen atom [O(3P)] and hydroxyl radical (OH), generated under two wavelengths (185 and 254 nm) of ultraviolet (UV) light were exposed to polyethylene (PE), polypropylene (PP) and polystyrene (PS) sheets. We investigated effects of the AOS exposure on the surface modification of these polymer sheets. Nonwoven sheet was used for the surface modification to eliminate an effect of the UV light irradiation. Although hydrophobicity of the PE and PP surfaces was maintained, the PS was changed into the hydrophilic surface.

Wafers with smooth Au thin films (rms surface roughness: < 0.5nm, thickness: < 50nm) were successfully bonded in ambient air at room temperature after an Ar radio frequency plasma activation process. The room temperature bonded glass wafers without any heat treatment showed a sufficiently high die-shear strength of 47-70MPa. Transmission electron microscopy observations showed that direct bonding on the atomic scale was achieved. This surface-activated bonding method is expected to be a useful technique for future heterogeneous photonic integration.

We prepared alumina passivation films for p-type silicon substrates by sol-gel wet process mainly using aluminum isopropoxide (Al(O-i-Pr)3) as a precursor material. The precursor solution was spin-coated onto p-type silicon substrates and then calcined for 1 hour in air. Minority carrier lifetime of the passivated wafers was evaluated for different calcination temperature conditions. We also compared the passivation quality of the alumina passivation films using different alumina precursor, aluminum acetylacetonate (Al(acac)3). Obtained effective minority carrier lifetime indicated that the lifetime is strongly depends on the calcination temperature. The substrate calcined below 400°C shows relatively short lifetime below 100 µsec. On the other hand, the substrate calcined around 500°C to 600°C indicates lifetime from 250 to 300 µsec. Calcination temperature dependence of the lifetime for the samples using Al(O-i-Pr)3 precursors shows almost the same as that using Al(acac)3.

We fabricated silicon solar cells with spin-coated sol-gel alumina passivation layers on the rear side. Spin-coated alumina passivation films have moderate passivation quality and are inferior to atomic layer deposited passivation films. However, low-cost and low temperature process of the sol-gel deposition is still beneficial for the cells using commercially available Cz silicon wafers. Thus, we consider an applicability of the spin-coated alumina passivation layer for rear side passivation. Dependence of cell efficiency on contact spacing and contact diameter of a rear electrode was investigated by both experiments and numerical calculation. The experimental results indicated that conversion efficiency of the cell is enhanced from 9.1% to 11.1% by optimizing an aperture ratio and contact spacing of the rear passivation layers. Numerical calculation indicated that small contact diameter with low aperture ratio of a rear passivation layer is preferable to achieve good cell performance in our experimental condition. We confirmed the effectivity of the spin-coated alumina passivation films for rear surface passivation of the low-cost silicon solar cells.

This paper deals with the diffraction of a monochromatic plane wave by a periodic grating. We discuss a problem how to obtain a numerical diffraction efficiency (NDE) satisfying the reciprocity theorem for diffraction efficiencies, because diffraction efficiencies are the subject of the diffraction theories. First, this paper introduces a new formula that decomposes an NDE into two components: the even component and the odd one. The former satisfies the reciprocity theorem for diffraction efficiencies, but the latter does not. Therefore, the even component of an NDE becomes an answer to our problem. On the other hand, the odd component of an NDE represents an unwanted error. Using such the decomposition formula, we then obtain another new formula that decomposes the conventional energy error into two components. One is the energy error made by even components of NDE's. The other is the energy error constructed by unwanted odd ones and it may be used as a reciprocity criterion of a numerical solution. This decomposition formula shows a drawback of the conventional energy balance. The total energy error is newly introduced as a more strict condition for a desirable solution. We point out theoretically that the reciprocal wave solution, an approximate solution satisfying the reciprocity for wave fields, gives another solution to our problem. Numerical examples are given for the diffraction of a TM plane wave by a very rough periodic surface with perfect conductivity. In the case of a numerical solution by the image integral equation of the second kind, we found that the energy error is much reduced by use of the even component of an NDE as an approximate diffraction efficiency or by use of a reciprocal wave solution.

We propose a framework to perform auto-radiometric calibration in photometric stereo methods to estimate surface orientations of an object from a sequence of images taken using a radiometrically uncalibrated camera under varying illumination conditions. Our proposed framework allows the simultaneous estimation of surface normals and radiometric responses, and as a result can avoid cumbersome and time-consuming radiometric calibration. The key idea of our framework is to use the consistency between the irradiance values converted from pixel values by using the inverse response function and those computed from the surface normals. Consequently, a linear optimization problem is formulated to estimate the surface normals and the response function simultaneously. Finally, experiments on both synthetic and real images demonstrate that our framework enables photometric stereo methods to accurately estimate surface normals even when the images are captured using cameras with unknown and nonlinear response functions.

The three dimensional (3D) reconstruction of a medical image sequence can provide intuitive morphologies of a target and help doctors to make more reliable diagnosis and give a proper treatment plan. This paper aims to reconstruct the surface of a renal corpuscle from the microscope renal biopsy image sequence. First, the contours of renal corpuscle in all slices are extracted automatically by using a context-based segmentation method with a coarse registration. Then, a new coevolutionary-based strategy is proposed to realize a fine registration. Finally, a Gauss-Seidel iteration method is introduced to achieve a non-rigid registration. Benefiting from the registrations, a smooth surface of the target can be reconstructed easily. Experimental results prove that the proposed method can effectively register the contours and give an acceptable surface for medical doctors.

This paper describes an equivalent circuit analysis of a meta-surface using a double-layered patch-type frequency-selective surface (FSS); the analysis considers the coupling between FSSs. Two types of double-layered structures are examined. One is a stacked structure and the other is an alternated structure. The results calculated using the equivalent circuit are in agreement with the results of the FDTD analysis. In addition, it is clarified that the stacked and alternated structures exhibit the common mode and the differential mode coupling, respectively. Moreover, experiments support analysis results for both stacked and alternated structures.

The electrical lubricants have been accepted to reduce friction of contacts and to prevent degradation of contact resistance. However, as the lubricant has an electrical insulation property it seems that application to contact surface is unsuitable for contact resistance. These mechanisms in contact interfaces have not fully understood. In this paper, relationships between contact resistance and contact load were examined with both clean and lubricated surfaces. Orientation of the lubricant molecules was observed by high magnification images of STM and AFM. There was no difference in contact resistance characteristics for both clean and lubricated surfaces in spite of lubricants thickness. The molecules were orientated perpendicular to the surface. This fact turns over an established theory of adsorption of non-polar lubricant to surface.

Radar cross section (RCS) of a patch array antenna is reduced using a switchable absorption/transmission surface. The switchable surface performs as between a radar absorber and transmission surface using diodes at 9GHz. The switchable surface was applied to the radome of a patch array and its radiation pattern and RCS reduction were evaluated. The gain and the radiation pattern with the radome was equivalent to that without the radome. The RCS reduction with the radome was 25dB compared to that without the radome.

Two plasmonic band-bass filters are analyzed: one is a grating-type filter and the other is a slit-type filter. The former shows a band-pass characteristic with a high transmission for a two-dimensional structure, while the latter exhibits a high transmission even for a three-dimensional structure with a thin metal layer.

In this study, we investigated Si(100), Si(110) and Si(111) surface flattening process utilizing sacrificial oxidation method, and its effect on Metal-Insulator-Semiconductor (MIS) diode characteristics. By the etching of the 100 nm-thick sacrificial oxide formed by thermal oxidation at 1100°C, the surface roughness of Si(100), Si(110) and Si(111) substrates were reduced. The obtained Root-Mean-Square (RMS) roughness of Si(100) was reduced from 0.22 nm (as-cleaned) to 0.07 nm (after etching), while it was reduced from 0.23 nm to 0.12 nm in the case of Si(110), and from 0.23 nm to 0.11 nm in the case of Si(111), respectively. Furthermore, it was found that time-dependent dielectric breakdown (TDDB) characteristics of MIS diodes for p-Si(100), p-Si(110) and p-Si(111) were improved with the reduction of Si surface RMS roughness.

The optical properties of arrays of nanoholes and nanoslits in Al films were investigated both numerically and experimentally. The choice of Al was based on its low cost and ease of processing, in addition to the fact that it has a higher plasma frequency than gold or silver, leading to lower optical losses at wavelengths of 400 to 500nm.

Low-temperature bonding methods of optoelectronic chips, such as laser diodes (LD) and photodiode (PD) chips, have been the focus of much interest to develop highly functional and compact optoelectronic devices, such as microsensors and communication modules. In this paper, room-temperature bonding of the optoelectronic chips with Au thin film to coined Au stud bumps with smooth surfaces (Ra: 1.3nm) using argon and hydrogen gas mixture atmospheric-pressure plasma was demonstrated in ambient air. The die-shear strength was high enough to exceed the strength requirement of MIL-STD-883F, method 2019 (×2). The measured results of the light-current-voltage characteristics of the LD chips and the dark current-voltage characteristics of the PD chips indicated no degradation after bonding.

This paper proposes a novel image integral equation of the first type (IIE-1) for a TE plane wave scattering from periodic rough surfaces with perfect conductivity by means of the method of image Green's function. Since such an IIE-1 is valid for any incident wavenumbers including the critical wavenumbers, the analytical properties of the scattered wavefield can be generally and rigorously discussed. This paper firstly points out that the branch point singularity of the bare propagator inevitably appears on the incident wavenumber characteristics of the scattered wavefield and its related quantities just at the critical wavenumbers. By applying a quadrature method, the IIE-1 becomes a matrix equation to be numerically solved. For a periodic rough surface, several properties of the scattering are shown in figures as functions of the incident wavenumbers. It is then confirmed that the branch point singularity clearly appears in the numerical solution. Moreover, it is shown that the proposed IIE-1 gives a numerical solution satisfying sufficiently the optical theorem even for the critical wavenumbers.

Isosurface extraction is one of the most popular techniques for visualizing scalar volume data. However, volume data contains infinitely many isosurfaces. Furthermore, a single isosurface might contain many connected components, or contours, with each representing a different object surface. Hence, it is often a tedious and time-consuming manual process to find and extract contours that are interesting to users. This paper describes a novel method for automatically extracting salient contours from volume data. For this purpose, we propose a contour gradient tree (CGT) that contains the information of salient contours and their saliency magnitude. We organize the CGT in a hierarchical way to generate a sequence of contours in saliency order. Our method was applied to various medical datasets. Experimental results show that our method can automatically extract salient contours that represent regions of interest in the data.

Topic features are useful in improving text summarization. However, independency among topics is a strong restriction on most topic models, and alleviating this restriction can deeply capture text structure. This paper proposes a hybrid topic model to generate multi-document summaries using a combination of the Hidden Topic Markov Model (HTMM), the surface texture model and the topic transition model. Based on the topic transition model, regular topic transition probability is used during generating summary. This approach eliminates the topic independence assumption in the Latent Dirichlet Allocation (LDA) model. Meanwhile, the results of experiments show the advantage of the combination of the three kinds of models. This paper includes alleviating topic independency, and integrating surface texture and shallow semantic in documents to improve summarization. In short, this paper attempts to realize an advanced summarization system.

In this study, Si(100) surface flattening process was investigated utilizing sacrificial oxidation method to improve Metal--Insulator--Semiconductor (MIS) diode characteristics. By etching of the 100,nm-thick sacrificial oxide formed by thermal oxidation at 1100$^{circ}$C, the surface roughness of Si substrate was reduced. The obtained Root-Mean-Square (RMS) roughness was decreased from 0.15,nm (as-cleaned) to 0.07,nm in the case of sacrificial oxide formed by wet oxidation, while it was 0.10,nm in the case of dry oxidation. Furthermore, time-dependent dielectric breakdown (TDDB) characteristic of Al/SiO$_{2}$(10,nm)/p-Si(100) MIS diode structures was found to be improved by the reduction of Si surface RMS roughness.

Displacement mapping has been widely used for adding geometric surface details to 3D mesh models. However, it requires sufficient tessellation of the mesh if fine details are to be represented. In this paper, we propose a method for applying the displacement mapping even on coarse models by using an augmented patch mesh. The patch mesh is a regularly tessellated flat square mesh, which is mapped onto the target area. Our method applies displacement mapping to the patch mesh for fitting it to the original mesh as well as for adding surface details. We generate a patch map, which stores three-dimensional displacements from the patch mesh to the original mesh. A displacement map is also provided for defining the new surface feature. The target area in the original mesh is then replaced with the patch mesh, and the patch mesh reconstructs the original shape using the patch map and the new surface detail is added using the displacement map. Our results show that our method conveniently adds surface features to various models. The proposed method is particularly useful if the surface features change dynamically since the original mesh is preserved and the separate patch mesh overwrites the target area at runtime.

The fabrication of a grating structure formed by a solid-state electrolyte layer on a dye-TiO$_{2}$ film by the nanoimprinting technique using a polydimethylsiloxane (PDMS) stamp and its application in photoelectric conversion devices are described. The PDMS grating pattern is imprinted from blu-ray disc recordable. A silver electrode was deposited on the patterned solid-state electrolyte layers. Surface plasmon resonance (SPR) excitation was observed in the fabricated solar cells by irradiation with white light. The photoelectric conversion properties were measured to study the effect of the two types of SPR excitations, i.e., the propagating surface plasmon on the Ag grating surface and the localized surface plasmon from the Au nanoparticles on TiO$_{2}$.