Direct-current biased optical orthogonal frequency division multiplexing (DCO-OFDM) converts bipolar OFDM signals into unipolar non-negative signals by introducing a high DC bias, which satisfies the requirement that the signal transmitted by intensity modulated/direct detection (IM/DD) must be positive. However, the high DC bias results in low power efficiency of DCO-OFDM. An adaptively biased optical OFDM was proposed, which could be designed with different biases according to the signal amplitude to improve power efficiency in this letter. The adaptive bias does not need to be taken off deliberately at the receiver, and the interference caused by the adaptive bias will only be placed on the reserved subcarriers, which will not affect the effective information. Moreover, the proposed OFDM uses Hartley transform instead of Fourier transform used in conventional optical OFDM, which makes this OFDM have low computational complexity and high spectral efficiency. The simulation results show that the normalized optical bit energy to noise power ratio (Eb(opt)/N0) required by the proposed OFDM at the bit error rate (BER) of 10-3 is, on average, 7.5 dB and 3.4 dB lower than that of DCO-OFDM and superimposed asymmetrically clipped optical OFDM (ACO-OFDM), respectively.

We study a visible light communication (VLC) system that modulates data signals by changing the color components of image contents on a digital signage display, captures them with an image sensor, and demodulates them using image processing. This system requires that the modulated data signals should not be perceived by the human eye. Previous studies have proposed modulation methods with a chromaticity component that is difficult for the human eye to perceive, and we have also proposed a modulation method with perceptually uniform color space based on human perception characteristics. However, which chromaticity component performs better depends on the image contents, and the evaluation only for some specific image contents was not sufficient. In this paper, we evaluate the communication and visual quality of the modulation methods with chromaticity components for various standard images to clarify the superiority of the method with perceptually uniform color space. In addition, we propose a novel modulation and demodulation method using diversity combining to eliminate the dependency of performance on the image contents. Experimental results show that the proposed method can improve the communication and visual quality for almost all the standard images.

In this paper, we describe a wavelength-division multiplexing visible-light communication (VLC) system using two colored light-emitting diodes (LEDs) with similar emission wavelengths. A multi-input multi-output signal-separation method using a neural network is proposed to cancel the optical cross chatter caused by the spectral overlap of LEDs. The experimental results demonstrate that signal separation using neural networks can be achieved in wavelength-multiplexed VLC systems with a bit error rate of less than 3.8×10-3 (forward error correction limit). Furthermore, the simulation results reveal that the carrier-to-noise ratio (CNR) is improved by 2dB for the successive interference canceller (SIC) compared to the zero-forcing method.

Visible light communication (VLC) and visible light ranging are applicable techniques for intelligent transportation systems (ITS). They use every unique light-emitting diode (LED) on roads for data transmission and range estimation. The simultaneous VLC and ranging can be applied to improve the performance of both. It is necessary to achieve rapid data rate and high-accuracy ranging when transmitting VLC data and estimating the range simultaneously. We use the signal modulation method of pulse-width modulation (PWM) to increase the data rate. However, when using PWM for VLC data transmission, images of the LED transmitters are captured at different luminance levels and are easily saturated, and LED saturation leads to inaccurate range estimation. In this paper, we establish a novel simultaneous visible light communication and ranging system for ITS using PWM. Here, we analyze the LED saturation problems and apply bicubic interpolation to solve the LED saturation problem and thus, improve the communication and ranging performance. Simultaneous communication and ranging are enabled using a stereo camera. Communication is realized using maximal-ratio combining (MRC) while ranging is achieved using phase-only correlation (POC) and sinc function approximation. Furthermore, we measured the performance of our proposed system using a field trial experiment. The results show that error-free performance can be achieved up to a communication distance of 55 m and the range estimation errors are below 0.5m within 60m.

To simultaneously enhance data rate and physical layer security (PLS) for low-luminance smartphone screen to camera uplink communication, space division multiplexing using high-luminance cell-size reduction arrangement is numerically analyzed and experimentally verified. The uplink consists of a low-luminance smartphone screen and an indoor telephoto camera at a long distance of 3.5 meters. The high-luminance cell-size reduction arrangement avoids the influence of spatial inter-symbol interference (ISI) and ambient light to obtain a stable low-luminance screen. To reduce the screen luminance without decreasing the screen pixel value, the arrangement reduces only the high-luminance cell area while keeping the cell spacing. In this study, two technical issues related to high-luminance cell-size reduction arrangement are solved. First, a numerical analysis and experimental results show that the high-luminance cell-size reduction arrangement is more effective in reducing the spatial ISI at low luminance than the conventional low-luminance cell arrangement. Second, in view point of PLS enhancement at wide angles, symbol error rate should be low in front of the screen and high at wide angles. A numerical analysis and experimental results show that the high-luminance cell-size reduction arrangement is more suitable for enhancing PLS at wide angles than the conventional low-luminance cell arrangement.

In this paper, we report the recent progress in visible light positioning and communication systems using light-emitting diodes (LEDs). Due to the wide deployment of LEDs for indoor illumination, visible light positioning (VLP) and visible light communication (VLC) using existing LEDs fixtures have attracted great attention in recent years. Here, we review our recent works on visible light positioning and communication, including image sensor-based VLP, photodetector-based VLP, integrated VLC and VLP (VLCP) systems, and heterogeneous radio frequency (RF) and VLC (RF/VLC) systems.

We discuss herein whether an optical wireless communication (OWC) system can be a candidate for post 5G or 6G cellular communication. Almost once per decade, cellular mobile communication is transformed by a significant evolution, with each generation developing a distinctive concept or technology. Interestingly, similar trends have occurred in OWC systems based on visible light and light fidelity (Li-Fi). Unfortunately, OWC is currently relegated to a limited role in any 5G scenario, but the debate whether this is unavoidable has yet to be settled. Whether OWC is adopted post 5G or 6G is not the vital issue; rather, the aim should be that OWC coexists with 5G and 6G communication technologies. In working toward this goal, research and development in OWC will continue to extend its benefits and standardize its systems so that it can be widely deployed in the market. For example, given that a standard already exists for a visible-light beacon identifier and Li-Fi, a service using this standard should be developed to satisfy user demand. Toward this end, we propose herein a method for visible-light beacon identification that involves using a rolling shutter to receive visible-light communications with a smartphone camera. In addition, we introduce a rotary LED transmitter for image-sensor communication.

This paper presents an analysis of the relationship between noise and bandwidth in visible light communication (VLC) systems. In the past few years, pre-emphasis and post-equalization techniques were proposed to extend the bandwidth of VLC systems. However, these bandwidth extension techniques also influence noise and sensitivity of the VLC systems. In this paper, first, we build a system model of VLC transceivers and circuit models of pre-emphasis and post-equalization. Next, we theoretically compare the bandwidth and noise of three different transceiver structures comprising a single pre-emphasis circuit, a single post-equalization circuit and a combination of pre-emphasis and post-equalization circuits. Finally, we validate the presented theoretical analysis using experimental results. The result shows that for the same resonant frequency, and for high signal-to-noise ratio (S/N), VLC systems employing post-equalization or pre-emphasis have the same bandwidth extension ability. Therefore, a transceiver employing both the pre-emphasis and post-equalization techniques has a bandwidth √2 times the bandwidth of the systems employing only the pre-emphasis or post-equalization. Based on the theoretical analysis of noise, the VLC system with only active pre-emphasis shows the lowest noise, which is a good choice for low-noise systems. The result of this paper may provide a new perspective of noise and sensitivity of the bandwidth extension techniques in VLC systems.

This letter investigates the secure transmission improvement scheme for indoor visible light communications (VLC) by using the protected zone. Firstly, the system model is established. For the input signal, the non-negativity and the dimmable average optical intensity constraint are considered. Based on the system model, the secrecy capacity for VLC without considering the protected zone is obtained. After that, the protected zone is determined, and the construction of the protected zone is also provided. Finally, the secrecy capacity for VLC with the protected zone is derived. Numerical results show that the secure performance of VLC improves dramatically by employing the protected zone.

Forward Error Correction (FEC) schemes have played an important role in intensity-modulation direct-detection (IM/DD) Visible Light Communication (VLC) systems. While hard-decision FEC schemes are inferior to soft-decision FEC codes in terms of decoding performance, they are widely used in these VLC systems because receivers are only capable of recognizing logical values 0 and 1. In this letter, we propose a method to calculate the log-likelihood ratios (LLR) values which are used as input of soft-decision FEC decoders. Simulation results show that Polar decoder using proposed method performs better than that of using the hard-decision technique.

Image sensor communication (ISC), derived from visible light communication (VLC) is an attractive solution for outdoor mobile environments, particularly for intelligent transport systems (ITS). In ITS-ISC, tracking a transmitter in the image plane is critical issue since vehicle vibrations make it difficult to selsct the correct pixels for data reception. Our goal in this study is to develop a precise tracking method. To accomplish this, vehicle vibration modeling and its parameters estimation, i.e., represetative frequencies and their amplitudes for inherent vehicle vibration, and the variance of the Gaussian random process represnting road surface irregularity, are required. In this paper, we measured actual vehicle vibration in a driving situation and determined parameters based on the frequency characteristics. Then, we demonstrate that vehicle vibration that induces transmitter displacement in an image plane can be modeled by only Gaussian random processes that represent road surface irregularity when a high frame rate (e.g., 1000fps) image sensor is used as an ISC receiver. The simplified vehicle vibration model and its parameters are evaluated by numerical analysis and experimental measurement and obtained result shows that the proposed model can reproduce the characteristics of the transmitter displacement sufficiently.

In this paper, we propose a precise indoor localization method using visible light communication (VLC) with dual-facing cameras on a smart device (mobile phone, smartphone, or tablet device). This approach can assist the visually impaired with navigation, or provide mobile-robot control. The proposed method is different from conventional techniques in that dual-facing cameras are used to expand the localization area. The smart device is used as the receiver, and light-emitting diodes on the ceiling are used as localization landmarks. These are identified by VLC using a rolling shutter effect of complementary metal-oxide semiconductor image sensors. The front-facing camera captures the direct incident light of the landmarks, while the rear-facing camera captures mirror images of landmarks reflected from the floor face. We formulated the relationship between the poses (position and attitude) of the two cameras and the arrangement of landmarks using tilt detection by the smart device accelerometer. The equations can be analytically solved with a constant processing time, unlike conventional numerical methods, such as least-squares. We conducted a simulation and confirmed that the localization area was 75.6% using the dual-facing cameras, which was 3.8 times larger than that using only the front-facing camera. As a result of the experiment using two landmarks and a tablet device, the localization error in the horizontal direction was less than 98 mm at 90% of the measurement points. Moreover, the error estimation index can be used for appropriate route selection for pedestrians.

A new class of visible light communication (VLC) systems, namely image sensor (IS) based VLC systems, has emerged. An IS consists of a two-dimensional (2D) array of photodetectors (PDs), and then VLC systems with an IS receiver are capable of exploiting the spatial dimensions invoked for transmitting information. This paper aims for providing a brief survey of topics related to the IS-based VLC, and then provides a matrix representation of how to map a series of one dimensional (1D) symbols onto a set of 2D symbols for efficiently exploit the associate grade of freedom offered by 2D VLC systems. As an example, the matrix representation is applied to the symbol mapping of layered space-time coding (L-STC), which is presented to enlarge the coverage of IS-based VLC that is limited by pixel resolution of ISs.

Spatial modulation (SM) is introduced into layered space-time coding (L-STC) used in image sensor (IS)-based visible light communication (VLC) systems. STC was basically investigated for extending the communication range of the IS-based VLC link [10], although it is out of the range when IS receivers are at the long distance from the LED array of the transmitter where the number of pixels capturing the transmitter on the image plane is less than the number of LEDs of the array. Furthermore, L-STC was done in [11] for increasing the reception rate with improving the pixel resolution while the receiver was approaching the transmitter. In this paper, SM is combined into L-STC by mapping additional information bits on the location of the pair of STC bit matrices of each layer. Experimental results show that additional SM bits are extracted with no error, without deteriorating the reception quality of and shrinking the transmission range of the original L-STC.

Image sensor communication (ISC), a type of visible light communication, is an emerging wireless communication technology that uses LEDs to transmit a signal and uses an image sensor in a camera to receive the signal. This paper discusses the present status of and future trends in ISC by describing the essential characteristics and features of ISC. Moreover, we overview the products and expected future applications of ISC.

In autonomous vehicles, driving in traffic poses significant challenges in vehicle-to-vehicle (V2V) communication and ranging. Currently interest centers on enhanced V2V communication with multi-sensor and cooperative approaches. In this paper we propose a novel bidirectional Laser Radar Visible Light Bidirectional Communication Boomerang System (LRVLB-ComBo). LRVLB-ComBo affords nuanced real-time two-way V2V communication as a basis for complex but reliable decision-making. Our approach involves combining existing automotive laser radar with visible light boomerang systems using THSS techniques. System simulations were performed using a random mix of extraneous interference pulse to evaluate system sensitivity to noise. Results suggest that LRVLB-ComBo is a viable two-way V2V communication system with increased ranging accuracy, enabling provision of detailed bidirectional data exchange for ITS precision, energy efficiency and safety.

Visible light communication is one of the key technologies for intelligent transport systems (ITS). However, current visible light communication systems require high-cost devices, such as high-speed image sensors, to support their high transmission rates. In this paper, we designed a communication system with combination of a low-speed commercial image sensor and a polygon mirror — namely, a fast-blinking light signal is scanned by the polygon mirror and captured as a residual image on the low-speed image sensor — to achieve visible light communication on existing mobile devices with high transmission rates. We also analyzed some required conditions, such as the relationship between the exposure time of the image sensor and the optimal resolution, and conducted experiments for performance evaluation. As a result, we found that the proposed system could achieve a data rate of 120bps, 10 times faster than that of the existing scheme when we compare them using the same image sensor. We also found that the proposed system can achieve a practical bit error rate in a low-noise environment.

This paper analyzes the transmission performances of visible light communication (VLC) based on unipolar orthogonal frequency division multiplexing (OFDM), which is compatible with intensity modulation and direct detection (IM/DD). Three existing unipolar OFDM schemes, namely DC biased optical OFDM (DCO-OFDM), asymmetrically clipped optical OFDM (ACO-OFDM), and flip-OFDM are investigated and compared. While these three schemes have been analyzed for indoor optical wireless communication (OWC) subject to the limitation on the transmit optical power, they have not been carefully investigated and compared for VLC when a large transmit power is available due to the illumination requirement, and the signal dynamic range (DR) becomes the main limitation. For the analysis, DR expressions of DCO-OFDM, ACO-OFDM, and flip-OFDM signals are first derived. Then, the bit error rate (BER) expression of each unipolar OFDM scheme is derived in terms of the DR. For data rates in the range of 1-10Mbps, under the system parameters based on typical indoor environments, DCO-OFDM is observed to outperform the other two schemes. This superiority of DCO-OFDM is in contrast with previously reported results that indicate the attractiveness of ACO-OFDM and flip-OFDM over DCO-OFDM when the transmit optical power is the main limitation. Finally, light dimming is considered to identify the illumination level below which DCO-OFDM loses this superiority.

This study introduces an image sensor based visible light communication (VLC) and its application to pose, position, and range estimations. There are two types of visible-light receiver: a photodiode and an image sensor. A photodiode is usually used as a reception device of VLC, and an image sensor consisting of a large number of pixels can also be used as a VLC reception device. A photodiode detects the signal intensity of incoming light, while an image sensor not only detects the incoming signal intensity but also an accurate angle of arrival of light emitted from a visible light transmitter such as a white LED light. After angles of arrival of light are detected by an image sensor, positioning and data reception can be performed. The ability of an image sensor to detect an accurate angle of arrival will provide attractive applications of VLC such as pose, position calculation, and range estimation. Furthermore, because the image sensor has the ability to spatially separate sources, outdoor positioning even with strong sunlight is possible by discarding the associated pixels of noise sources.

We propose an optical fiber connection navigation system that uses visible light communication for an integrated distribution module in a central office. The system realizes an accurate database, requires less skilled work to operate and eliminates human error. This system can achieve a working time reduction of up to 88.0% compared with the conventional work without human error for the connection/removal of optical fiber cords, and is economical as regards installation and operation.