The locally one-dimensional finite-difference time-domain (FDTD) method in cylindrical coordinates is extended to a frequency-dependent version. The fundamental scheme is utilized to perform matrix-operator-free formulations in the right-hand sides. For the analysis of surface plasmon polaritons propagating along a plasmonic grating, the computation time is significantly reduced to less than 10%, compared with the explicit cylindrical FDTD method.

A plasmonic black pole (PBP) consisting of a series of touching spherical metal surfaces is analyzed using the finite-difference time-domain (FDTD) method with the periodic boundary condition. First, the wavelength characteristics of the PBP are studied under the assumption that the PBP is omnidirectionally illuminated. It is found that partial truncation of each metal sphere reduces the reflectivity over a wide wavelength range. Next, we consider the case where the PBP is illuminated with a cylindrical wave from a specific direction. It is shown that an absorptivity of more than 80% is obtained over a wavelength range of λ=500 nm to 1000 nm. Calculation regarding the Poynting vector distribution also shows that the incident wave is bent and absorbed towards the center axis of the PBP.

In X-ray computed tomography, scattered X-rays are generally removed by using a post-patient collimator located in front of the detector. In this paper, we show that the scattered X-rays have the potential to improve the estimation accuracy of the attenuation coefficient in computed tomography. In order to clarify the problem, we simplified the geometry of the computed tomography into a thin cylinder composed of a homogeneous material so that only one attenuation coefficient needs to be estimated. We then conducted a Monte Carlo numerical experiment on improving the estimation accuracy of attenuation coefficient by measuring the scattered X-rays with several dedicated toroidal detectors around the cylinder in addition to the primary X-rays. We further present a theoretical analysis to explain the experimental results. We employed a model that uses a T-junction (i.e., T-junction model) to divide the photon transport into primary and scattered components. This division is processed with respect to the attenuation coefficient. Using several T-junction models connected in series, we modeled the case of several scatter detectors. The estimation accuracy was evaluated according to the variance of the efficient estimator, i.e., the Cramer-Rao lower bound. We confirmed that the variance decreases as the number of scatter detectors increases, which implies that using scattered X-rays can reduce the irradiation dose for patients.

This letter proposes a novel modulation classification method for overlapped sources named LRGP involving multinomial logistic regression (MLR) and multi-gene genetic programming (MGGP). MGGP based feature engineering is conducted to transform the cumulants of the received signals into highly discriminative features and a MLR based classifier is trained to identify the combination of the modulation formats of the overlapped sources instead of signal separation. Extensive simulations demonstrate that LRGP yields superior performance compared with existing methods.

This paper presents low-noise amplifier (LNA)-less 300-GHz CMOS receivers that operate above the NMOS unity-power-gain frequency, fmax. The receivers consist of a down-conversion mixer with a doubler- or tripler-last multiplier chain that upconverts an LO1/n signal into 300 GHz. The conversion gain of the receiver with the doubler-last multiplier is -19.5 dB and its noise figure, 3-dB bandwidth, and power consumption are 27 dB, 27 GHz, and 0.65 W, respectively. The conversion gain of the receiver with the tripler-last multiplier is -18 dB and its noise figure, 3-dB bandwidth, and power consumption are 25.5 dB, 33 GHz, and 0.41 W, respectively. The receivers achieve a wireless data rate of 32 Gb/s with 16QAM. This shows the potential of the moderate-fmax CMOS technology for ultrahigh-speed THz wireless communications.

This paper introduces a formation method for 3-dimensional 6 ch.×6 ch. shuffling structures with graded-index (GI) circular core in a multimode polymer optical waveguide for optical printed circuit boards (OPCBs) using a unique photomask-free fabrication technique named the Mosquito method. The interchannel pitch of the fabricated waveguides is 250µm, where all the channels consist of both horizontal and vertical bending structures and the last 6 channels in parallel cross over the first 6 channels. We also report 3-dimensional S-shaped polymer waveguides. In the S-shaped waveguides, the first and last 6 channels with both horizontal and vertical core bending composing the above 3-dimensional shuffling waveguide are separated, in order to evaluate the effect of over-crossing on the loss. It is experimentally confirmed that there is no excess insertion loss due to the shuffling structure in the 3-D shuffling waveguide. The evaluated crosstalk of the 3-D shuffling waveguide is lower than -30dB. The 3-D shuffling waveguide proposed in this paper will be a promising component to achieve high bandwidth density wiring for on-board optical interconnects.

To meet the demand for continuous increase in data traffic, full usage of polarization freedom of light is becoming inevitable in the next-generation optical communication and datacenter networks. In particular, Stokes-vector modulation direct-detection (SVM-DD) formats are expected as potentially cost-effective method to transmit multi-level signals without using costly coherent transceivers in the short-reach links. For the SVM-DD formats to be practical, both the transmitter and receiver need to be substantially simpler, smaller, and lower-cost as compared to coherent counterparts. To this end, we have recently proposed and demonstrated novel SV modulator and receiver circuits realized on monolithic InP platforms. With compact non-interferometric configurations, relatively simple fabrication procedures, and compatibility with other active photonic components, the proposed devices should be attractive candidate in realizing low-cost monolithic transceivers for SVM formats. In this paper, we review our approaches as well as recent progresses and provide future prospects.

In this paper, the problem on secure communication based on chaos synchronization is investigated. The dual channel information transmitting technology is proposed to increase the security of secure communication system. Based on chaos synchronization, a new digital secure communication scheme is presented for a class of master-slave systems. Finally some numerical simulation examples are given to demonstrate the effectiveness of the given results.

A penta-band antenna based on the mu-negative transmission line is presented for radio frequency (RF) energy harvesting application. The antenna utilizes five radiation modes; two quarter wavelength resonances, three quarter wavelength resonance, zeroth order resonance, and first order resonance. The parasitic radiating strip antenna generates quarter wavelength resonance radiation. The dual band antenna based on two unit cell mu-negative (MNG) transmission line gives birth to the zeroth order resonance (ZOR) mode and the first order resonance (FOR) mode. The parasitic radiating strip and dual band antenna based on two unit mu-negative (MNG) transmission line are magnetically coupled by a feed monopole with gap. This feed monopole, simultaneously, radiates at quarter and three quarter wavelength resonance frequency to cover the other bands. The multi-mode coupling mechanism of this penta-band antenna is well modeled by our derived equivalent circuit. The measured radiation efficiencies are more than 87% over the entire penta-band.

This paper proposes a lossy image coding method for still images. In this method, recursive and non-recursive type intra prediction techniques are adaptively selected on a block-by-block basis. The recursive-type intra prediction technique applies a linear predictor to each pel within a prediction block in a recursive manner, and thus typically produces smooth image values. In this paper, the non-recursive type intra prediction technique is extended from the angular prediction technique adopted in the H.265/HEVC video coding standard to enable interpolative prediction to the maximum possible extent. The experimental results indicate that the proposed method achieves better coding performance than the conventional method that only uses the recursive-type prediction technique.

We have previously introduced the static dependency pair method that proves termination by analyzing the static recursive structure of various extensions of term rewriting systems for handling higher-order functions. The key is to succeed with the formalization of recursive structures based on the notion of strong computability, which is introduced for the termination of typed λ-calculi. To bring the static dependency pair method close to existing functional programs, we also extend the method to term rewriting models in which functional abstractions with patterns are permitted. Since the static dependency pair method is not sound in general, we formulate a class; namely, accessibility, in which the method works well. The static dependency pair method is a very natural reasoning; therefore, our extension differs only slightly from previous results. On the other hand, a soundness proof is dramatically difficult.

Instruction set randomization (ISR) is a cost-effective obfuscation technique that modifies or enhances the relationship between instructions and machine languages. An Instruction Register File (IRF), a list of frequently used instructions, can be used for ISR by providing the way of indirect access to them. This study examines the IRF that integrates a positional register, which was proposed as a supplementary unit of the IRF, for the sake of tamper resistance. According to our evaluation, with a new design for the contents of the positional register, the measure of tamper resistance was increased by 8.2% at a maximum, which corresponds to a 32.2% increase in the size of the IRF. The number of logic elements increased by the addition of the positional register was 3.5% of its baseline processor.

Automatic speech recognition (ASR) and keyword search (KWS) have more and more found their way into our everyday lives, and their successes could boil down lots of factors. In these factors, large scale of speech data used for acoustic modeling is the key factor. However, it is difficult and time-consuming to acquire large scale of transcribed speech data for some languages, especially for low-resource languages. Thus, at low-resource condition, it becomes important with which transcribed data for acoustic modeling for improving the performance of ASR and KWS. In view of using acoustic data for acoustic modeling, there are two different ways. One is using the target language data, and another is using large scale of other source languages data for cross-lingual transfer. In this paper, we propose some approaches for efficient selecting acoustic data for acoustic modeling. For target language data, a submodular based unsupervised data selection approach is proposed. The submodular based unsupervised data selection could select more informative and representative utterances for manual transcription for acoustic modeling. For other source languages data, the high misclassified as target language based submodular multilingual data selection approach and knowledge based group multilingual data selection approach are proposed. When using selected multilingual data for multilingual deep neural network training for cross-lingual transfer, it could improve the performance of ASR and KWS of target language. When comparing our proposed multilingual data selection approach with language identification based multilingual data selection approach, our proposed approach also obtains better effect. In this paper, we also analyze and compare the language factor and the acoustic factor influence on the performance of ASR and KWS. The influence of different scale of target language data on the performance of ASR and KWS at mono-lingual condition and cross-lingual condition are also compared and analyzed, and some significant conclusions can be concluded.

In this paper, we propose a highly accurate method for estimating the quality of images compressed using fractal image compression. Using an iterated function system, fractal image compression compresses images by exploiting their self-similarity, thereby achieving high levels of performance; however, we cannot always use fractal image compression as a standard compression technique because some compressed images are of low quality. Generally, sufficient time is required for encoding and decoding an image before it can be determined whether the compressed image is of low quality or not. Therefore, in our previous study, we proposed a method to estimate the quality of images compressed using fractal image compression. Our previous method estimated the quality using image features of a given image without actually encoding and decoding the image, thereby providing an estimate rather quickly; however, estimation accuracy was not entirely sufficient. Therefore, in this paper, we extend our previously proposed method for improving estimation accuracy. Our improved method adopts a new image feature, namely lacunarity. Results of simulation showed that the proposed method achieves higher levels of accuracy than those of our previous method.

The 1-bit band-pass delta-sigma modulator (BP-DSM) achieves high resolution if it uses an oversampling technique. This method can generate concurrent dual-band RF signals from a digitally modulated signal using a 1-bit digital pulse train. It was previously reported that the adjacent channel leakage ratio (ACLR) deteriorates owing to the asymmetrical waveform created by the pulse transition mismatch error of the rising and falling waveforms in the time domain and that the ACLR can be improved by distortion compensation. However, the reported distortion compensation method can only be performed for single-band transmission, and it fails to support multi-band transmission because the asymmetrical waveform compensated signal extends over a wide frequency range and is itself a harmful distortion outside the target band. Unfortunately, the increase of out-of-band power causes the BP-DSM unstable. We therefore propose a distortion compensator for a concurrent dual-band 1-bit BP-DSM that consists of a noise transfer function with a quasi-elliptic filter that can control the out-of-band gain frequency response against out-of-band oscillation. We demonstrate that dual-band LTE signals, each with 40MHz (2×20MHz) bandwidth, at 1.5 and 3.0GHz, can be compensated concurrently for spurious distortion under various combinations of rising and falling times and ACLR of up to 48dB, each with 120MHz bandwidth, including the double sided adjacent channels and next adjacent channels, is achieved.

This letter studies secure transmission design with finite alphabet input for cooperative jamming network under individual power constraint. By adopting the zero-force scheme, where the jamming signal is fully laid in the null space of the relay-destination channel, the problem of enhancing the achievable secrecy rate is decomposed into two independent subproblems: relay weights design and power control. We reveal that the problem of relay weights design is identical to the problem of minimizing the maximal equivalent source-eavesdropper channel gain, which can be transformed into a semi-definite programming (SDP) problem and thus is tackled using interior point method. Besides, the problem of power control is solved with the fundamental relation between mutual information and minimum mean square error (MMSE). Numerical results show that the proposed scheme achieves significant performance gains compared to the conventional Gaussian design.

The microfabrication technique based on SR (Synchrotron Radiation) direct etching process has recently been applied to construct PTFE microstructures. This paper attempts to fabricate an integrated PTFE-filled waveguide Butler matrix for short millimeter-wave by SR direct etching. First, a cruciform 3-dB directional coupler and an intersection circuit (0-dB coupler) are designed at 180 GHz. Then, a 4×4 Butler matrix with horn antennas is designed and fabricated. Finally, the measured radiation patterns of the Butler matrix are shown.

High frame rate and ultra-low delay matching system plays an increasingly important role in human-machine interactive applications which call for higher frame rate and lower delay for a better experience. The large amount of processing data and the complex computation in a local feature based matching system, make it difficult to achieve a high process speed and ultra-low delay matching with limited resource. Aiming at a matching system with the process speed of more than 1000 fps and with the delay of less than 1 ms/frame, this paper puts forward a local binary feature based matching system with field-programmable gate array (FPGA). Pixel selection based 4-1-4 parallel matching and intensity directed symmetry are proposed for the implementation of this system. To design a basic framework with the high process speed and ultra-low delay using limited resource, pixel selection based 4-1-4 parallel matching is proposed, which makes it possible to use only one-thread resource consumption to achieve a four-thread processing. Assumes that the orientation of the keypoint will bisect the patch best and will point to the region with high intensity, intensity directed symmetry is proposed to calculate the keypoint orientation in a hardware friendly way, which is an important part for a rotation-robust matching system. Software experiment result shows that the proposed keypoint orientation calculation method achieves almost the same performance with the state-of-art intensity centroid orientation calculation method in a matching system. Hardware experiment result shows that the designed image process core supports to process VGA (640×480) videos at a process speed of 1306 fps and with a delay of 0.8083 ms/frame.

We have investigated the influence of the ferromagnet magnetization on the transport properties of intrinsic Josephson junctions in Co/Au/BSCCO/Au/Co hybrid structure under applied magnetic fields. The current-voltage characteristic at 77K in a zero-field showed the multiple quasiparticle branches with hysteresis similar to that of conventional intrinsic Josephson junctions. On the other hand, it was observed that the critical current shows a clear asymmetric field dependence with respect to the direction of the field sweep, resulting in hysteretic behavior. By comparing the field dependence of critical current with magnetization curve of the sample, we found that the critical current is strongly suppressed in the antiparallel configuration of the relative magnetization orientation of two Co layers due to the accumulation of spin-polarized quasiparticles in intrinsic Josephson junctions. The observed suppression of the critical current is as large as more than 20%.

In this paper, a dual-polarized phased array based polarization state modulation method is proposed to enhance the physical-layer security in millimeter-wave (mm-wave) communication systems. Indeed, we utilize two polarized beams to transmit the two components of the polarized signal, respectively. By randomly selecting the transmitting antennas, both the amplitude and the phase of two beams vary randomly in undesired directions, which lead to the PM constellation structure distortion in side lobes, thus the transmission security is enhanced since the symbol error rate increases at the eavesdropper side. To enhance the security performance when the eavesdropper is close to the legitimate receiver and located in main beam, the artificial noise based on the orthogonal vector approach is inserted randomly between two polarized beams, which can further distort the constellation structure in undesired directions and improve the secrecy capacity in main beam as well. Finally, theoretical analysis and simulation results demonstrate the proposed method can improve the transmission security in mm-wave communication systems.