We have developed an all-optical fiber link antenna measurement system for a millimeter wave 5th generation mobile communication frequency band around 28 GHz. Our developed system consists of an optical fiber link an electrical signal transmission system, an antenna-coupled-electrode electric-field (EO) sensor system for 28GHz-band as an electrical signal receiving system, and a 6-axis vertically articulated robot with an arm length of 1m. Our developed optical fiber link electrical signal transmission system can transmit the electrical signal of more than 40GHz with more than -30dBm output level. Our developed EO sensor can receive the electrical signal from 27GHz to 30GHz. In addition, we have estimated a far field antenna factor of the EO sensor system for the 28GHz-band using an amplitude center modified antenna factor estimation equation. The estimated far field antenna factor of the sensor system is 83.2dB/m at 28GHz.

Physical contact (PC) optical connectors realize long-term stability by maintaining contact with the optical fiber even during temperature fluctuations caused by the microscopic displacement of the ferrule endface. With multicore fiber (MCF) connectors, stable PC connection conditions need to be newly investigated because MCFs have cores other than at the center. In this work, we investigated the microscopic displacement of connected ferrule endfaces using the finite element method (FEM). As a result, by using MCF connectors with an apex offset, we found that the allowable fiber undercut where all the cores make contact is slightly smaller than that of single-mode fiber (SMF) connectors. Therefore, we propose a new equation for determining the allowable fiber undercut of MCF connectors. We also fabricated MCF connectors with an allowable fiber undercut and confirmed their reliability using the composite temperature/humidity cyclic test.

This paper summarizes recent reports on the internet's energy consumption and the internet's benefits on climate actions. It discusses energy-efficiency and the need for a common standard for evaluating the climate impact of future communication technologies and suggests a model that can be adapted to different internet applications such as streaming, online reading and downloading. The two main approaches today are based on how much data is transmitted or how much time the data is under way. The paper concludes that there is a need for a standardized method to estimate energy consumption and CO2 emission related to internet services. This standard should include a method for energy-optimizing future networks, where every Wh will be scrutinized.

Various optical fiber connectors have been developed during the 40 years since optical fiber communications systems were first put into practical use. This paper describes the key technologies for optical connectors and recent technical issues.

In 5th generation (5G) and Beyond 5G mobile communication systems, it is expected that numerous antennas will be densely deployed to realize ultra-broadband communication and uniform coverage. However, as the number of antennas increases, total power consumption of all antennas will also increase, which leads to a negative impact on the environment and operating costs of telecommunication operators. Thus, it is necessary to simplify an antenna structure to suppress the power consumption of each antenna. On the other hand, as a way to realize ultra-broadband communication, millimeter waves will be utilized because they can transmit signals with a broader bandwidth than lower frequencies. However, since millimeter waves have a large propagation loss, a propagation distance is shorter than that of low frequencies. Therefore, in order to extend the propagation distance, it is necessary to increase an equivalent isotropic radiated power by beamforming with phased array antenna. In this paper, a phased antenna array module in combined with analog radio over fiber (A-RoF) technology for 40-GHz millimeter wave is developed and evaluated for the first time. An 8×8 phased array antenna for 40-GHz millimeter wave with integrated photodiodes and RF chains has been developed, and end-to-end transmission experiment including 20km A-RoF transmission and 3-m over-the-air transmission from the developed phased array antenna has been conducted. The results showed that the 40-GHz RF signal after the end-to-end transmission satisfied the criteria of 3GPP signal quality requirements within ±50 degrees of main beam direction.

Multi-band WDM transmission beyond the C+L-band is a promising technology for achieving larger capacity transmission by a limited number of installed fibers. In addition to the C- and L-band, we can expect to use the S-band as the next band. Although the development of optical components for new bands, particularly transceivers, entails resource dispersion, which is one of the barriers to the realization of multi-band systems, wavelength conversion by transparent all-optical signal processing enables new wavelength bandtransmission using existing components. Therefore, we proposed a transmission system including a new wavelength band such as the S-band and made it possible to use a transceiver for the existing band by performing the whole-band wavelength conversion without using a transceiver for the new band. As a preliminary verification to demonstrate multi-band WDM transmission including S-band, we investigated the application of a novel wavelength converter between C-band and S-band, which consists of periodically poled lithium niobate waveguide, to the proposed system. We first characterized the conversion efficiency and noise figure of the wavelength converter and estimated the transmission performance of the system through the wavelength converter. Using the evaluated wavelength converters and test signals of 64 channels arranged in the C-band at 75-GHz intervals, we constructed an experimental setup for S-band transmission through an 80-km standard single-mode fiber. We then demonstrated error-free transmission of real-time 400-Gb/s DP-16QAM signals after forward error correction decoding. From the experimental results, it was clarified that the wavelength converter which realizes the uniform lossless conversion covering the whole C-band effectively achieves the S-band WDM transmission, and it was verified that the capacity improvement of the multi-band WDM system including the S-band can be expected by applying it in combination with the C+L-band WDM system.

Multi-core fiber (MCF) is one of the promising space-division multiplexing technologies to increase the capacity of optical networks. MCF-based networks have two challenges. One is the inter-core crosstalk (XT) that degrades the quality of optical signals in two neighboring fiber cores. The other is network protection against link failures that cause massive data loss. One way to protect against multiple link failures is to prepare physically separated links as a backup network. Probabilistic protection improves the efficiency of protection by allowing a certain probability of protection failure. Existing studies on backup network design with probabilistic protection do not target MCF-based networks, which raises problems such as protection failure due to the inter-core XT and excessive consumption of optical resources. To address these problems, this paper proposes a XT-aware backup network design model for the MCF optical path networks. The proposed model protects the network against probabilistic multiple link failures. We adopt probabilistic protection that allows a certain probability of protection failure due to the inter-core XT and minimizes the required number of links in the backup network. We present an algorithm to satisfy the probabilistic protection requirement and formulate the model as an integer linear programming problem. We develop a heuristic approach to apply the proposed model to larger networks. Numerical results observe that the proposed model requires fewer links than the dedicated allocation model, which provisions the backup paths in the same manner as the primary paths.

This paper presents a compact fully-differential distributed amplifier using a coupled inductor. Differential distributed amplifiers are widely required in optical communication systems. Most of the distributed amplifiers reported in the past are single-ended or pseudo-differential topologies. In addition, the differential distributed amplifiers require many inductors, which increases the silicon cost. In this study, we use differentially coupled inductors to reduce the chip area to less than half and eliminate the difficulties in layout design. The challenge in using coupled inductors is the capacitive parasitic coupling that degrades the flatness of frequency response. To address this challenge, the odd-mode image parameters of a differential artificial transmission line are derived using a simple loss-less model. Based on the analytical results, we optimize the dimensions of the inductor with the gradient descent algorithm to achieve accurate impedance matching and phase matching. The amplifier was fabricated in 0.18-µm CMOS technology. The core area of the amplifier is 0.27 mm2, which is 57% smaller than the previous work. Besides, we demonstrated a small group delay variation of ±2.7 ps thanks to the optimization. the amplifier successfully performed 30-Gbps NRZ and PAM4 transmissions with superior jitter performance. The proposed technique will promote the high-density integration of differential traveling wave devices.

One of cost-effective ways to increase the transmission capacity of current standard wavelength division multiplexing (WDM) transmission systems is to use a wavelength band other than the C-band to transmit in multi-band. We proposed the concept of multi-band system using wavelength conversion, which can simultaneously process signals over a wide wavelength range. All-optical wavelength conversion could be used to convert C-band WDM signals into other bands in a highly nonlinear fiber (HNLF) by four-wave mixing and allow to simultaneously transmit multiple WDM signals including other than the C-band, with only C-band transceivers. Wavelength conversion has been reported for various nonlinear waveguide materials other than HNLF. In such nonlinear materials, we noticed the possibility of wideband transmission by dispersion-tailored silicon-on-insulator (SOI) waveguides. Based on the CMOS process has high accuracy, it is expected that the chromatic dispersion fluctuation could be reduced in mass production. As a first step in the investigation of the broadness of wavelength conversion using SOI-based waveguides, we designed and fabricated dispersion-tailored 12 strip waveguides provided with an edge coupler at both ends. Each of the 12 waveguides having different widths and lengths and is connected to fibers via lensed fibers or by lenses. In order to characterize each waveguide, the pump-probe experimental setup was constructed using a tunable light source as pump and an unmodulated 96-ch C-band WDM test signal. Using this setup, we evaluate insertion loss, input power dependence, conversion bandwidth and conversion efficiency. We confirmed C-band test signal was converted to the S-band and the L-band using the same silicon waveguide with 3dB conversion bandwidth over 100-nm. Furthermore, an increased design tolerance of at least 90nm was confirmed for C-to-S conversion by shortening the waveguide length. It is confirmed that the wavelength converters using the nonlinear waveguide has sufficiently wide conversion bandwidth to enhance the multi-band WDM transmission system.

We propose a radio-over-fiber (RoF) system with 1-bit outphasing modulation. The proposed RoF system does not require a power-hungry digital-to-analog converter in access points and relaxes the operation speed of optical transceivers to reduce device cost. We introduce two configurations to enable 1-bit outphasing modulation in our system; mixed-signal and all-digital configurations. In the mixed-signal configuration, the effects of harmonics and phase/amplitude mismatch on the adjacent channel leakage ratio (ACLR) were analyzed through simulation, and wideband transmission with a signal bandwidth of 400 MHz was experimentally verified, complying with the 3rd Generation Partnership Project (3GPP) standard for millimeter-wave band. Moreover, wide-band transmission with a signal bandwidth of 1 GHz was also experimentally verified for beyond-5G and 6G. The all-digital configuration can be implemented in a standard digital design flow. This configuration was also verified to comply with the 3GPP standard by properly selecting the intermediate and sampling frequencies to mitigate the effects of folded harmonics and quantization noise. Finally, the proposed RoF system with both configurations has been shown to have a higher bandwidth efficiency compared with other systems complying with the 3GPP standard for the ACLR. Therefore, the proposed RoF system provides a cost-effective in-building wireless solution for 5G and 6G mobile network systems.

An enzymatic biofuel cell (BFC) that uses lactic acid in human sweat as fuel to generate electricity is an attractive power source for wearable devices. A BFC capable of generating electricity with human sweat has been developed. It comprised a flexible tattoo seal type battery with silver oxide vapor deposited on a flexible material and conductive carbon nanotubes printed on it. The anode and cathode in this battery were arranged in a plane (planar type). This work proposes a thin laminated enzymatic BFC by inserting a cellulose nanofiber (CNF) sheet between two electrodes to absorb human sweat (stack-type). Optimization of the anode and changing the arrangement of electrodes from planar to stack type improved the output and battery life. The stack type is 43.20μW / cm2 at 180mV, which is 1.25 times the maximum power density of the planar type.

Conventional enzymatic biofuel cells (EBFCs) use glucose solution or glucose from human body. It is desirable to get glucose from a substance containing glucose because the glucose concentration can be kept at the optimum level. This work developed a biofuel cell that generates electricity from cellulose, which is the main components of plants, by using decomposing enzyme of cellulase. Cellulose nanofiber (CNF) was chosen for the ease of decomposability. It was confirmed by the cyclic voltammetry method that cellulase was effective against CNF. The maximum output of the optimized proposed method was 38.7 μW/cm2, which was 85% of the output by using the glucose solution at the optimized concentration.

In this study, we discuss a structure that realizes a wideband polarization splitter comprising fiber 1 with a single core and fiber 2 with circular pits, which touch the top and bottom of a single core. The refractive index profile of the W type was adopted in the core of fiber 1 to realize the wideband. We compared the maximum bandwidth of BW-15 (bandwidth at an extinction ratio of -15dB) for the W type obtained in this study with those (our previous results) of BW-15 for the step and graded types with cores and pits at the same location; this comparison clarified that the maximum bandwidth of BW-15 for the W type is 5.22 and 4.96 times wider than those of step and graded types, respectively. Furthermore, the device length at the maximum bandwidth improved, becoming slightly shorter. The main results of the FPS in this study are all obtained by numerical analysis based on our proposed MM-DM (a method that combines the multipole method and the difference method for the inhomogeneous region). Our MM-DM is a quite reliable method for high accuracy analysis of the FPS composed of inhomogeneous circular regions.

Multi-core fiber (MCF) is one of the most promising candidates for achieving ultra-wideband optical transmission in the near future. To build a network using MCF, a high-performance and reliable MCF connector is indispensable. We have developed an SC-type optical connector for MCF and confirmed its excellent optical performance, mechanical durability, and environmental reliability. To put the communication system using MCF into practical use, it is necessary to establish a procedure for measuring the initial connection characteristics. Fan-in / fan-out (FIFO) devices are indispensable for measuring the connection characteristics of MCF connectors. To measure the return loss of the MCF connector, it is necessary to remove the influence of reflection at the FIFO itself and at the connection points with the FIFO. In this paper, we compare four types of return loss measurement procedures (three usual method and a new method we proposed) and find that most stable measurement method involves using our new method, the OCWR method without FIFO. The OCWR method without FIFO is considered to be the most advantageous when used for outgoing inspection of connectors. The reason is that it eliminates the measurement uncertainty caused by the FIFO and enables speedy measurement.

In this paper, we report an experimental and numerical analysis of ultrahigh-speed coherent Nyquist pulse transmission. First, we describe a low-nonlinearity dispersion compensator for ultrahigh-speed coherent Nyquist pulse transmission; it is composed of a chirped fiber Bragg grating (CFBG) and a liquid crystal on silicon (LCoS) device. By adopting CFBG instead of inverse dispersion fiber, the nonlinearity in a 160km transmission line was more than halved. Furthermore, by eliminating the group delay fluctuation of the CFBG with an LCoS device, the residual group delay was reduced to as low as 1.42ps over an 11nm bandwidth. Then, by using the transmission line with the newly constructed low-nonlinearity dispersion compensator, we succeeded in improving the BER performance of single-channel 15.3Tbit/s-160km transmission by one-third compared with that of a conventional dispersion-managed transmission line and obtained a spectral efficiency of 8.7bit/s/Hz. Furthermore, we numerically analyzed the BER performance of its Nyquist pulse transmission. The numerical results showed that the nonlinear impairment in the transmission line is the main factor limiting the transmission performance in a coherent Nyquist pulse transmission, which becomes more significant at higher baud rates.

In order to further reduce the transmission rate of multi-channel satellite broadcast signals, whose carrier-to-noise ratio (CNR fluctuates due to rainfall attenuation, we propose a novel digitized radio-over-fiber (DRoF) -based optical re-transmission system based on adaptive combination compression for ultra-high definition (UHD) broadcasting satellite (BS)/communications satellite (CS) broadcast signals. The proposed system reduces the optical re-transmission rate of BS/CS signals as much as possible while handling input CNR fluctuations. Therefore, the transmission rate of communication signals in time-division multiplexing (TDM) transmission is ensured, and network sharing of communication signals and broadcast signals via passive optical network (PON) is realized. Based on the ITU-R P.618-13 prediction model, an experimental evaluation is performed using estimates of the long-term statistics of attenuation due to rainfall. The attenuation is evaluated as a percentage of the time that long-term re-transmission service is available. It is shown that the proposed system is able to accommodate a wide range of rainfall attenuation and achieve a 99.988% time percentage for the duration of service provision. In order to show the rate reduction effect of the proposed system, the quantization bit reduction effect as a function of the input CNR, which depends on rainfall attenuation, is experimentally confirmed. Experiments show that service operation time of 99.978% can be achieved by 3-bit transmission. This means a 62.5% reduction in transmission rate is realized compared to conventional fixed quantization. Furthermore, the average quantization bit number in our system for service operation times is 3.000, indicating that most service operation times are covered by just 3-bit transmission.

We propose a technique based on Brillouin optical time domain analysis for measuring loss and crosstalk in few-mode fibers (FMFs). The proposed technique extracts the loss and crosstalk of a specific mode in FMFs from the Brillouin gains and Brillouin gain coefficients measured under two different conditions in terms of the frequency difference between the pump and probe lights. The technique yields the maximum loss and crosstalk at a splice point by changing the electrical field injected into an FMF as the pump light. Experiments demonstrate that the proposed technique can measure the maximum loss and crosstalk of the LP11 mode at a splice point in a two-mode fiber.

We present detailed measurements and analysis of the guided acoustic wave Brillouin scattering (GAWBS)-induced depolarization noise in a multi-core fiber (MCF) used for a digital coherent optical transmission. We first describe the GAWBS-induced depolarization noise in an uncoupled four-core fiber (4CF) with a 125μm cladding and compare the depolarization noise spectrum with that of a standard single-mode fiber (SSMF). We found that off-center cores in the 4CF are dominantly affected by higher-order TRn,m modes rather than the TR2,m mode unlike in the center core, and the total power of the depolarization noise in the 4CF was almost the same as that in the SSMF. We also report measurement results for the GAWBS-induced depolarization noise in an uncoupled 19-core fiber with a 240μm cladding. The results indicate that the amounts of depolarization noise generated in the cores are almost identical. Finally, we evaluate the influence of GAWBS-induced polarization crosstalk (XT) on a coherent QAM transmission. We found that the XT limits the achievable multiplicity of the QAM signal to 64 in a transoceanic transmission with an MCF.

Quantum noise ultimately restricts the transmission distance in fiber communication systems using optical amplifiers. This paper investigates the quantum-noise-limited performance of optical binary phase-shift keying transmission using gain-saturated phase-sensitive amplifiers (PSAs) as optical repeaters. It is shown that coherent state transmission, where ultimately clean light in the classical sense is transmitted, and endless transmission, where the transmission distance is not restricted, are theoretically achievable under certain system conditions owing to the noise suppression effects of the gain-saturated PSA.

This paper reviews the evolutionary process that reduced the transmission loss of silica optical fibers from the report of 20dB/km by Corning in 1970 to the current record-low loss. At an early stage, the main effort was to remove impurities especially hydroxy groups for fibers with GeO2-SiO2 core, resulting in the loss of 0.20dB/km in 1980. In order to suppress Rayleigh scattering due to composition fluctuation, pure-silica-core fibers were developed, and the loss of 0.154dB/km was achieved in 1986. As the residual main factor of the loss, Rayleigh scattering due to density fluctuation was actively investigated by utilizing IR and Raman spectroscopy in the 1990s and early 2000s. Now, ultra-low-loss fibers with the loss of 0.150dB/km are commercially available in trans-oceanic submarine cable systems.