The family Pk of graphs with proper-path-width at most k is minor-closed. It is known that the number of minimal forbidden minors for a minor-closed family of graphs is finite, but we have few such families for which all the minimal forbidden minors are listed. Although the minimal acyclic forbidden minors are characterized for Pk, all the minimal forbidden minors are known only for P1. This paper lists 36 minimal forbidden minors for P2, and shows that there exist no other minimal forbidden minors for P2.

In the millimeter-wave propagation inside of figure U guideway of maglev, a multipath model using the ray-tracing method is presented. Prediction shows that delay spread is exceedingly small and high speed data transmission more than 100Mbps is possible without an equalizer.

Interdigital transducers (IDTs) with leaky-SAWs propagating on 36 YX-LiTaO3, and 41 and 64 YX-LiNbO3 were theoretically analyzed, providing a new equivalent circuit. This equivalent circuit included attenuation constant due to leakage as well as conductance caused by bulkwave radiation. All circuit parameters were derived by solving integral equations. Fundamental experiments showed fairly good agreement between theoretical and experimental results, which gave very accurate design tools for leaky-SAW devices.

Ever increasing demand for higher bandwidth memories, which is fueled by multimedia and 3D graphics, seems to be somewhat satisfied with various emerging memory solutions. This paper gives a review of these emerging DRAM architectures and a performance comparison based on a condition to let the readers have some perspectives of the future and optimized graphics systems.

We have investigated the Josephson microwave self-radiation and the linewidth from different types of YBa2Cu3Oy(YBCO) grain boundary junctions: natural grain boundary junctions, step-edge junctions and bicrystal junctions. The Josephson self-rediation was directly observed using a total power radiometer receiver with receiving frequencies fREC=1.7-72 GHz. All junctions exhibited microwave self-radiation peaks with intensity of order of 10-12-10-14 W. For step-edge and bicrystal junction, they appeared at a voltage related to the Josephson frequency-voltage relation, V=n(h/2e)f, while for natural grain boundary junctions, the above relation did not hold, suggesting a Josephson medium property. For all types of junctions the observed Josephson linewidth deviated from the theoretical RSJ values due to the extra noise source in the grain boundary junction. The Josephson linewidth decreased with increasing the receiving frequency for all type of junctions. The reduction of Josephson linewidth at higher frequencies indicates that the critical current fluctuations due to a critical current spread at small bias voltages and a crystalline disorientation at the junction boundary generate an additional noise in grain boundary junctions.

Efficiency of network resource can be improved by statistical multiplexing in ATM networks. If cell traffic characteristics of each connection could be obtained beforehand, we could admit maximum connections while satisfying the QoS (Quality of Service) objective. Since such traffic characteristics as an average rate and a mean burst length are difficult to anticipate, only peak rate will be used for CAC (connection admission control). The peak rate assignment strategy will, however, lead to inefficient network utilization for bursty traffic. This paper proposes an adaptive admission control using real-time traffic measurements to overcome the above problem. This scheme is based on two-state cell stream model composed of overload and underload states. The two-state model simplifies the measuring algorithm, which is suited for online processing. Performance of this scheme is investigated through simulation study for multiplexing of on-off sources with a wide spectrum of traffic characteristics. Since the proposed control scheme exploits measurements of cell streams, it achieves nearly optimum bandwidth efficiency.

The recent progress of B-ISDN signaling systems has enabled networks to handle calls which require a wide variety of ATM connection sets. This paper is concerned with the circuit group which handles calls requesting asymmetric forward and backward multi-connections, and has the capability of both bandwidth negotiation and bandwidth reservation as a traffic control for enhancing call blocking performance. A model of the circuit group is first established focusing on the call level characteristics of the group, and then a method based on the reduced load approximation and an approximate analysis of a multirate group is proposed for calculating approximate blocking probabilities. The accuracy of the approximation method is evaluated numerically by comparing with an exact method and simulation. Further the impact of bandwidth negotiation and reservation on call blockings is examined based on numerical examples.

A graph G is said to be universal for a family F of graphs if G contains every graph in F as a subgraph. A minimum universal graph for F is a universal graph for F with the minimum number of edges. This paper considers a minimum universal graph for the family Fkn of graphs on n vertices with path-width at most k. We first show that the number of edges in a universal graph Fkn is at least Ω(kn log(n/k)). Next, we construct a universal graph for Fkn with O(kn log(n/k)) edges, and show that the number of edges in a minimum universal graph for Fkn is Θ(kn log(n/k)) .

A uniquely-structured Usage Parameter Control (UPC) method named Virtual-shaping is proposed which considers cell arrival time jitter between user and UPC point. The method uses a modified Dangerous Bridge UPC circuit (Sliding window type) and virtually (logically) shapes cell traffic using cell arrival time compensation to offset cell delay variation (CDV). In addition, the proposed method is based on a cell-buffer-less structure and can be realized with reasonable hardware. The method yields precise and accurate monitoring. Computer simulations show that the method offers higher network utilization than the conventional Leaky Bucket based UPC method. The proposed method will make it possible to create more effective B-ISDNs, and more cost-effective broadband VBR services.

Recently as one of attractive applications in the B-ISDN era, LAN/MAN interconnection through an ATM network has been coming up because burstiness of LAN/MAN data traffic is applicable to distinctive features of cell based ATM network. In order to overcome a difference of the connection mode, i.e., CL packet transfer of LAN/MAN and CO cell transfer of ATM network, a number of interworking and bandwidth allocation mechanisms have been proposed. These methods, however, indicate both merits and drawbacks concerning with CL data transfer quality, network resource efficiency and processing overhead in IWU/CLS and the network, and have been mostly evaluated only for a single IWU model. This paper aims at showing the most appropriate method of LAN/MAN interworking for IWU-IWU or IWU-CLSF connection. In the paper, some interworking issues including a general qualitative assessment are clarified. We then evaluate the selected five interworking methods based on Bandwidth Renegotiation (BR) and VC Establishment (VCE), which are combined with Traffic Enforcement Functions (TEFs) based on policing mechanisms and Cell Loss Control (CLC) scheme. By transient and stationary simulation approach for a single IWU and an IWU-CLS connection model, the most applicable method is indicated as a case study from view points of the communication quality, effective use of the bandwidth and processing load.

We introduce the interval set of a graph G which is a representation of the proper-path-decomposition of G, and show a linear time algorithm to construct an optimal interval set for any tree T. It is shown that a proper-path-decomposition of T with optimal width can be obtained from an optimal interval set of T in O(n log n) time.

The FDDI-II is a high speed and flexible backbone LAN. It can divide the capacity into one packet-switched channel with flexible bandwidth and up to 16 isochronous channels which may be allocated for a variety of real-time services such as video and voice. How to allocate and maintain isochronous bandwidth is an important issue for supporting good services to users. The FDDI-II standard proposed a centralized scheme to achieve this goal. In this paper, we propose a new scheme in a distributed fashion for the management of isochronous bandwidth. Based on our scheme, the network can support various services in a more efficient way.

The newly developed high speed DRAMs are introduced and their innovative circuit techniques for achieving a high data bandwidth are described; the synchronous DRAM, the cache DRAM and the Rambus DRAM. They are all designed to fill the performance gap between MPUs and the main memory of computer systems, which will diverge in '90s. Although these high speed DRAMs have the same purpose to increase the data bandwidth, their approaches to accomplish it is different, which may in turn lead to some advantages or disadvantages as well as their fields of applications. The paper is intended not only to discuss them from technical overview, but also to be a guide to DRAM users when choosing the best fitting one for their systems.

In this paper, trellis coded modulation with bandwidth expansion is examined. The proposed scheme is a modified Symbol-rate-increased TCM [3]-[5], which allows the bandwidth expansion ratio to be varied to an arbitrary value. The Symbol-rate-increased TCM has been shown to be a particular case of the proposed scheme. Simulation results have clarified that the proposed scheme achieves a significant improvement over an uncoded scheme in an AWGN channel.

An improvement of Q evaluation is discussed. The Resonance Curve Area method was confirmed to give a deviation in the order of 6104. The result was three times more accurate than the widely known Q evaluating method which utilizes the cursor function installed in a network analyzer. A discussion is also made on the physical validity of the RCA method. It is shown that the application of the RCA method improves the accuracy of the cavity perturbation method. Actual measurements have shown that the deviation of dielectric constant is less than 1% and that of the loss tangent is less than 3%, in the order of 104. The accuracy of the RCA method was estimated to be three times that of the conventional cavity perturbation technique. The consistency of the perturbation with other methods has also confirmed. The accuracy comparison to more accurate formulae derived from a rigorous solution have shown that the difference is sufficiently small.

A local area network (LAN) can now provide high-speed data communications in a local area environment to establish distributed processing among personal computers and workstations, and the need for interconnecting LANs, which are geographically distributed, is naturally arising. Asynchronous Transfer Mode (ATM) technology has been widely recognized as a promising way to provide the high-speed wide area networks (WAN) for Broadband Integrated Services Digital Network (B-ISDN), and the commercial service offerings are expected in the near future. The ATM network seems to have a capability as a backbone network for interconnecting LANs, and the LAN interconnection is expected to be the first service in ATM networks. However, there remain some technical challenges for this purpose; one of the main difficulties in LAN interconnection is the support of connectionless traffic by the ATM network, which is basically a connection-oriented network. Another one is the way of achieving the very high-speed data transmission over the ATM network. In this paper, we first discuss a LAN internetworking methodology based on the current technology. Then, the recent deployments of LAN interconnection methods through B-ISDN are reviewed.

In this paper, we study a dynamic bandwidth control which is expected an effective use of network resources in transmitting highly bursty traffic generated by, e.g., interconnected LAN systems. First, a new LAN traffic model is proposed in which correlation of not only packet interarrival times but also packet lengths are considered. An analytic model for a LAN-ATM gateway is next introduced. It employs the dynamic bandwidth control using the proposed LAN traffic model and some performance measures are derived by it. The analytic model takes into account the probability that a bandwidth increase request may be rejected. Finally, some numerical examples are provided using the analysis method and performance comparisons between the dynamic and fixed bandwidth controls are made. As a result, it is quantitatively indicated that () if the equivalent bandwidth is used in average, the dynamic bandwidth control keeps packet and cell loss rates one to two orders lower than the fixed bandwidth control, () when the more strict QOS in terms of loss rate is requested, the dynamic bandwidth control can become more effective.

This paper proposes a high-speed VP bandwidth control scheme for ATM networks that utilizes a distributed control mechanism. First, the characteristics of VPs are compared with those of digital paths in STM networks. A distributed control scheme is adopted for rapid control. The basic elements and the necessary distributed function, the control algorithm, and the message transmission mechanism, are elucidated. The bandwidth alteration time with the proposed algorithm is estimated by considering network element processing and queuing delay. The proposed VP bandwidth control scheme can be applied to both public networks and leased line services. Finally, this paper focuses on its application to leased line services, and discusses the resource reduction effects of the proposed scheme.

In this paper, the characteristics of microstrip lines near the edge of dielectric substrate are analyzed by improving the rectangular boundary division method. The numerical results indicate the changes of the characteristics of a microstrip line when the strip conductor is closely located to the edge. When the distance the dielectric substrate edge to the strip conductor is less than the thickness of dielectric substrate, the effects of the edge on the line characteristics are no longer negligible. The numerical results in this paper show high computation accuracy without increasing computation time. Our improvement is effective for the analysis of the microstrip lines both for the narrow strip conductor and the strip conductor close to the edge. The relative errors between the numerical results and the measured values are less than 1.2%.

The minimum transferable linewidth by X-ray is derived using waveguide analysis. The minimum width is determined by the refractive index of the absorber and does not depend on the X-ray wavelength. Therefore there is an optimum mask aperture size which provides the minimum linewidth. By using Au as the absorber, 8 nm linewidth is attainable.