An integrator is quite a suitable active element for high-speed filters. The effect of its excess phase shifts, however, is severe in the case of high-Q filter realization. The deterioration due to the excess phase shifts cannot be avoided when only integrators are used as frequency-dependent elements like in leapfrog realization. This paper describes a design of second-order high-speed and high-Q filters with low sensitivity to excess phase shifts of integrators by adding a passive RC circuit. The proposed method can drastically reduce the effect due to the undesirable pole of an integrator, which is the cause of the excess phase shifts, compared to conventional filters using only integrators. As an example, a fourth-order bandpass filter with 5-MHz center frequency and Q=25 is implemented by the proposed method on a monolithic chip. The results obtained here show quite good agreement with the theoretical values. This demonstrates effectiveness of the proposed method and feasibility of high-speed and high-Q filters on a monolithic chip.

We analyze the average bit error probability (BER) performances of BPSK with pilot tone in the frequency-selective Rayleigh fading channel, which can be characterized by the delay power spectrum due to multipath fading. The analysis is based on the error probability conditioned on the receiver input envelope in order to investigate the diversity effects. With taking into consideration of predetection receiving filter characteristic, the average BER is evaluated by treating the normalized standard deviation (rms delay spread), τ0/T (T: digital symbol period), of the delay power spectrum, BT product of predetection filter and power distribution between BPSK signal and pilot tone as parameters. The results show that the optimum power distribution (kopt) can be determined mainly according to the ratio (α) of tone extracting filter bandwidth to predetection filter bandwidth provided that α is small. For fixed α, τ0/T and kopt corresponding to α, optimum BT product, which minimizes the error rate, exists and the value is dependent on signal energy per bit to noise power spectral density ratio (SNR), and is affected slightly by the delay power spectrum shapes. In this paper, one-sided exponential, Gaussian and double spike shapes are treated as delay power spectrum shapes. On the average BER characteristics due to delay spread with fixed α, BT and kopt corresponding to α, the delay power spectrum shape is of no importance for τ0/T0.06. For τ0/T0.06, in the case of double spike delay power spectrum, BER is less than that for the other two spectral shapes. By making use of the selection diversity with 2-branch and predetection filter with optimum BT product, SNR can be improved by 16dB at the average BER of 10-4.

This paper describes a fiber-optic microcell radio system with a spectral delivery switch to meet traffic demands. Optical link performance is discussed from the view points of link loss and noise figure aimed at system design. The theoretical carrier-to-noise ratio (CNR) performance is shown as a function of the input electrical power of the laser and the received optical power. Improvement of dynamic range defined by both CNR and intermodulation distortion is proposed by using the frequency modulation (FM) technique. The experimental results using the proposed technique indicate that the performance is much better than that of conventional methods. Moreover, economical diversity planning delivery methods over fibers are presented. This strategy will provide more cost effective and flexible networks.

A typical fault-tolerance technique of systolic arrays is to include redundant processors and links so that the array is reconfigurable when some processors fail. Another typical technique is to implement each processor by a majority voter and N (N3) copies of processors so that the faults of up to N-2 copies of processors can be masked without reconfiguration. This paper proposes a systolic linear array called reconfigurable modular redundant linear array (RMA) that combines these techniques with N4. When up to 2 copies of each processor fail in RMA, the faults can be masked without reconfiguration. When some voters or more than 2 copies of a processor fail, RMA can be reconfigured by specifying a new switch pattern. In order to perform reconfiguration efficiently, we present a reconfiguration algorithm with time complexity O (n), where n is the number of processors in RMA.

An optimal algorithm for decomposing a special type of the Hasse diagram into a minimum set of disjoint paths is described. It is useful for testing the consistency of functional dependencies.

Surface construction is known as a way to visualize volume data. Although currently used algorithms such as marching cubes have good enough quality for volume visualization, they do not ensure adequate surface topology. These algorithms work well when the surface is rather simple. While when complicated, the surface does not separate the internal and external spaces, that is, there exist some holes on the surface, or exist redundant overlaps or self-intersection. Actually, adequate surface topology is important not only for visualization but for laser stereolithography, which creates real 3D plastic objects. In the present paper, we propose a new method that produces a set of triangular patches from a given volume data. The fact that the set of patches has no holes, no redundancy, no self-intersection, and has orientable closed surface topology is shown.

This paper describes a new technique for isolated word recognition that uses both pitch information and spectral information. In conventional methods, words with similar phoneme features tend to be misrecognized even if their phonemes are accented differently because these methods use only spectral information. It is possible to improve recognition accuracy by considering pitch patterns of words. Many phonetically-similar Japanese words are classified by pitch patterns. In this technique, a pitch pattern template is produced by averaging pitch patterns obtained from a set of words which have the same accent pattern. A measure for word recognition is proposed. This measure based on a combination of the phoneme likelihood and the pitch pattern distance which is the distance between a pitch pattern of an input speech and pitch pattern templates. Speaker-dependent word recognition experiments were carried out using 216 Japanese words uttered by five male and five female speakers. The proposed technique reduces the recognition error rate by 40% compared with the conventional method using only phoneme likelihood.

The problem of two-dimensional scattering of electromagnetic waves by a grating with several strips arbitrarily oriented in one period is analyzed by means of the Wiener-Hopf technique together with the formulation using the concept of the mutual field. A formulation for the analysis of multiple scattering from the grating is based on the representation of the scattered field by a grating composed of one strip in one period. The Wiener-Hopf equations and a representation of the scattered wave are obtained. The characteristic of the sampling function is used to expand the unknown function associated with the field on the strip into a series, and then the Wiener-Hopf equations are reduced to a set of simultaneous equations. For evaluation of the convergence and the errors in the numerical results, the relative error with respect to the extrapolated value and the square error for satisfaction of the boundary condition are computed. From numerical comparison of the present method with other various methods, it is found that the present method provides us accurate results. Some numerical examples of the reflection coefficients are presented for the reflection grating and transmission gratings.

A simple inequality that guarantees stability of perturbed linear state space models is proposed. It is shown that the result is superior to some existing result in sharpness and possesses some advantageous aspects.

Reactive gases such air pollution agents as H2S or SO2 usually corrode the electrical contact surfaces. Since corrosion products formed on the surface increase contact resistance, they harmfully degrades contact reliability. To prevent the corrosion of the surface, oil coating on it may be effective. The oil film acts basically as a barrier for reaction between the corrosive gas and the surface. For thin film coating, the corrosion inhibition can not be expected. However, effect of film thickness on the corrosion property has not been clarified. In the present study, in order to clarify the corrosion inhibition of the oil coating for the contacts, the stearic acid coating on Ag (silver) contact surface was studied from view-point of the relationship between the thickness of the coating film and the contact resistance. As results, the effect of the stearic acid coating on corrosion inhibition in the atmosphere contained with H2S 3 ppm was found. However, the corrosion of the surface coated with thin stearic acid film occurred at microscopically scattered thin patiches in the specific pattern of the film. Existing of the optimum thickness of the stearic acid coating which gives both minimum contact resistance and effective corrosion inhibition was found. In the intermediate film thickness, this optimum thickness was induced by the increased contact resistance due to corrosion of the thin film region and insulation property of the stearic acid in the thick film region. Moreovr,it was found that this optimum thickness was affected by corrosion time. At the early stage of corrosion, the optimum thickness was about 200 . However, the corrosion time becomes longer as 700 min, this optimum thickness changed to thick as 1000 . With this increase in the thickness, the contact resistance in the optimum thickness rised to high level. Furthermore, the contact resistance in the optimum thickness decreased with increase in the contact load. However, dependence of the contact load on the optimum thickness was not recognized under a certain corrosion time.

This paper theoretically evaluates the external electro-optic (EO) sampling of high-speed electrical signals using poled polymers as materials for a proximity electric-field sensor. Based on the derivation of the half-wave voltage and the analysis of a static electric field coupled to the polymeric media placed over IC interconnections, invasiveness, voltage sensitivity, and spatial resolution have been discussed. The polymeric sensors have shown to be used in contact with the IC interconnections with negligibly small invasiveness, thus making polymeric sensors provide higher sensitivity and spatial resolution than inorganic crystals such as GaAs and KD*P.

This paper proposes the laser diode receiving mixer which utilizes the laser diode nonlinearity. The laser diode receiving mixer can make the bidirectional fiber optic link simple and cost-effective. These laser diodes are applied to configure the LD-LD MIX link which consists of two laser diodes, two local oscillators, two microwave switches and one fiber cable. The LD-LD MIX link configuration is extended to introduce novel two fiber optic links, i.e. the local suppression link and the image cancellation link. These links utilize the combination of microwave circuits and optical devices. These configurations are experimentally investigated at microwave frequencies and the QPSK signal transmission is successfully demonstrated.

We apply Fahlman and Lebiere's (FL) algorithm to network synthesis and incremental learning by making use of already-trained networks, each performing a specified task, to design a system that performs a global or extended task without destroying the information gained by the previously trained nets. Investigation shows that the synthesized or expanded FL networks have generalization ability superior to Back propagation (BP) networks in which the number of newly added hidden units must be pre-specified.

This paper describes an automatic transistor model parameter generation technique for a circuit simulator which can take device geometry into account. An 'area factor' is used to generate model parameters for different transistor shapes; however, the conventional method could not reflect the actual geometry differences other than for the emitter area. This resulted in inaccurate model parameters and such parameters were not acceptable to accurately simulate circuits for RF ICs. The proposed technique uses actually measured parameters and process data for a reference transistor and generates the individual model parameters for different shape transistors. In this technique, the parasitic resistor values are calculated and fitted in place of directly extracting them from the measured data. This ensures a better estimate. The reference transistor is made sufficiently large to neglect measurement errors in generating the parasitic capacitors. Thus, the model parameters for a very small transistor can be generated accurately. The model generating procedure has been implemented as a pre-processor to SPICE. This technique enables a fast turn around for RF IC circuit design which uses various shape transistors.

In this paper, we propose an extended LR parsing algorithm, called LR parsing with a category reachability test (the LR-CRT algorithm). The LR-CRT algorithm enables a parser to efficiently recognize those sentences that belong to a specified grammatical category. The key point of the algorithm is to use an augmented LR parsing table in which each action entry contains a set of reachable categories. When executing a shift or reduce action, the parser checks whether the action can reach a given category using the augmented table. We apply the LR-CRT algorithm to improve a speech recognition system based on two-level LR parsing. This system uses two kinds of grammars, inter- and intra-phrase grammars, to recognize Japanese sentential speech. Two-level LR parsing guides the search of speech recognition through two-level symbol prediction, phrase category prediction and phone prediction, based on these grammars. The LR-CRT algorithm makes possible the efficient phone prediction based on the phrase category prediction. The system was evaluated using sentential speech data uttered phrase by phrase, and attained a word accuracy of 97.5% and a sentence accuracy of 91.2%

Progress of speech recognition based on the hidden Markov model has made it possible to realize man-machine dialogue systems capable of operating in real time. In spite of considerable effort, however, few systems have been successfully developed because of the lack of appropriate dialogue models. This paper reports on some of technology necessary to develop a dialogue system with which one can converse comfortably. The emphasis is placed on the following three points: how a human converses with a machine; how errors of speech recognition can be recovered through conversation; and what it means for a machine to be cooperative. We examine the first problem by investigating dialogues between human speakers, and dialogues between a human speaker and a simulated machine. As a consideration in the design of dialogue control, we discuss the relation between efficiency and cooperativeness of dialogue, the method for confirming what the machine has recognized, and dynamic adaptation of the machine. Thirdly, we review the research on the friendliness of a natural language interface, mainly concerning the exchange of initiative, corrective and suggestive answers, and indirect questions. Lastly, we describe briefly the current state of the art in speech recognition and synthesis, and suggest what should be done for acceptance of spontaneous speech and production of a voice suitable to the output of a dialogue system.

It is difficult to decide whether or not a given cryptographic protocol is secure even though the cryptographic algorithm used for the protocol is assumed to be secure. We have proposed an algorithm to decide the security of cryptographic protocols under several conditions. In this paper, we review our algorithm and report a system to verify the security. The system has be implemented on a computer. By using this system, we have verified the security of several protocols efficiently.

This paper describes design issues of a speech dialogue system, the evaluation of the system, and the data collection of spontaneous speech in a transportation guidance domain. As it is difficult to collect spontaneous speech and to use a real system for the collection and evaluation, the phenomena related with dialogues have not been quantitatively clarified yet. The authors constructed a speech dialogue system which operates in almost real time, with acceptable recognition accuracy and flexible dialogue control. The system was used for spontaneous speech collection in a transportation guidance domain. The system performance evaluated in the domain is the understanding rate of 84.2% for the utterances within the predefined grammar and the lexicon. Also some statistics of the spontaneous speech collected are given.

We define the communication complexity of a perfect zero-knowledge interactive proof (ZKIP) as the expected number of bits communicated to achieve the given error probabilities (of both the completeness and the soundness). While the round complexity of ZKIPs has been studied greatly, no progress has been made for the communication complexity of those. This paper shows a perfect ZKIP whose communication complexity is 11/12 of that of the standard perfect ZKIP for a specific class of Quadratic Residuosity.

New illumination principle for photolithography is investigated. As the optical microlithography approaches its own limit, it becomes apparent that the simple extrapolation of the present technology is not sufficient for the future demands. This paper introduces the new imaging technology that overcomes such a boundary. First, the basic imaging formulae are analyzed and the illumination light is classified into 4 cases. 3-beam case and 2-beam case carry the object information, and the comparison of these 2 cases is carried out theoretically. It can be shown that the 2-beam case has greater depth of focus than that of the 3-beam case, though it has inferior contrast at the best focus. Since this degradation, however, has little effect, the enlargement of the depth of focus can be achieved. In reality, 2-dimensional imaging must be considered. Quadrupole effect can be deduced by the results of the analysis. It shows great improvement in the depth of focus near resolution limit. As it can be applied to the conventional masks, it can be a promising candidate for fhe future lithography. Experimental results are also shown to demonstrate the analysis.