We examine the characteristics of the past successful m-valued I2L and ROMs that have been designed and we discuss the reasons of their success and withdraw. We look at the problems associated with scaling of m-valued CMOS current mode circuits. Then we discuss the tolerance issue, the respective propagation delays of binary and m-valued ICs and the interconnection issue. We conclude with the challenges for m-valued circuits in the competition with the exponential performance increase of binary circuits.

This paper studies multidimensional linear periodically shift-variant digital filters (LPSV filters). The notion of a generalized multidimensional transfer function is presented for LPSV filters. The frequency characteristic of the filters is discussed in terms of this transfer function. Since LPSV filters can decompose the spectrum of an input signal into some spectral partitions and rearrange the spectrum, LPSV filters can serve as a frequency scrambler. To show the effect of multidimensional frequency scramble, 2-D LPSV filters are designed based on the 1-D Parks-McClellan algorithm. The resultant LPSV filters divide the input spectrum into some components that are permuted and possibly inverted with keeping the symmetric of the spectrum. Experimental results are presented to illustrate the effectiveness of frequency scramble for real images.

In this paper, a design method is described for very low sensitivity fully-balanced narrow-band band-pass switched-capacitor filters (SCF's) whose worst-case sensitivities of the amplitude responses become zero at every reflection zero. The proposed method is based on applying the low-pass to high-pass transformation, the pseudo two-path technique and the capacitance-ratio reduction technique to very low sensitivity low-pass SC ladder filters. A design example of the band-pass SCF with a quality factor Q250 is given to verify the proposed method. The remarkable advantages of this approach are very low sensitivity to element-value variations, a small capacitance spread, a small total capacitance, and clock-feedthrough noise immunity inside the passband.

This paper presents a design of a new multiple-valued matching VLSI processor for high-speed reasoning. It is useful in the application for real-time rule-based systems with large knowledge bases which are programmable. In order to realize high-speed reasoning, the matching VLSI processor can perform the fully parallel pattern matching between an input data and rules. On the based of direct multiple-valued encoding of each attribute in an input data and rules, pattern matching can be described by using only a programmable delta literal. Moreover, the programmable delta literal circuit can be easily implemented using two kinds of floating-gate MOS devices whose threshold voltages are controllable. In fact, it is demonstrated that four kinds of threshold voltages in a practical floating-gate MOS device can be easily programmable by appropriately controlling the gate, the drain and the source voltage. Finally, the inference time of the quaternary matching VLSI processor with 256 rules and conflict resolution circuits is estimated at about 360 (ns), and the chip area is reduced to about 30 percent, in comparison with the equivalent binary implementation.

When we study time-domain electromagnetic fields, we frequently use the finite-difference time-domain (FD-TD) method. In this paper, we discuss errors of the FD-TD method and present the optimum mesh spacings in the FD-TD method when the three mesh spacings are different.

Broadband ISDN, using asynchronous transfer mode, are expected to carry traffic of different classes, each with its own set of traffic characteristics and performance requirements. To achieve the quality of service in ATM networks, a suitable buffer management scheme is needed. In this paper, we propose a buffer management scheme using a priority service discipline to improve the delay time of delay-sensitive class and the packet loss ratio of loss-sensitive class. The proposed priority scheme requires simple buffer management logic and minor processing overhead. We also analyze the delay time and the packet loss ratio for each class of service. The results indicate that the required buffer size of the proposed priority scheme is reduced and the delay time of each class of service is controlled by a parameter. If the control parameter is appropriately chosen, the quality of service of each class is improved.

The demand for high-speed image processing is obvious in many real-world computations such as robot vision. Not only high throughput but also small latency becomes an important factor of the performance, because of the requirement of frequent visual feedback. In this paper, a high-performance VLSI image processor based on the multiple-valued residue arithmetic circuit is proposed for such applications. Parallelism is hierarchically used to realize the high-performance VLSI image processor. First, spatially parallel architecture that is different from pipeline architecture is considered to reduce the latency. Secondly, residue number arithmetic is introduced. In the residue number arithmetic, data communication between the mod mi arithmetic units is not necessary, so that multiple mod mi arithmetic units can be completely separated to different chips. Therefore, a number of mod mi multiply adders can be implemented on a single VLSI chip based on the modulus-slice concept. Finally, each mod mi arithmetic unit can be effectively implemented in parallel structure using the concept of a pseudoprimitive root and the multiple-valued current-mode circuit technology. Thus, it is made clear that the throughout use of parallelism makes the latency 1/3 in comparison with the ordinary binary implementation.

In this paper, a general theory on multiple-valued static random-access-memory (RAM) is investigated. A criterion for a stable and an unstable modes is proved with a strict mathematical method and expressed with a diagrammatic representation. Based on the theory, an NMOS 6-transistor ternary and a quaternary static RAM (SRAM) cells are proposed and simulated with PSPICE. The detail circuit design and realization are analyzed. A 10-valued CMOS current-mode static RAM cell is also presented and fabricated with standard 5-µm CMOS technology. A family of multiple-valued flip-flops is presented and they show to have desirable properties for use in multiple-valued sequential circuits. Both PSPICE simulations and experiments indicate that the general theory presented are very useful and effective tools in the optimum design and circuit realization of multiple-valued static RAMs and flip-flops.

An adder-based arithmetic VLSI processor using the SD number system is proposed for the applications of real-time computation such as intelligent robot system. Especially in the intelligent robot control system, not only high throughput but also small latency is a very important subject to make quick response for the sensor feedback situation, because the next input sample is obtained only after the robot actually moves. It is essential in the VLSI architecture for the intelligent robot system to make the latency as small as possible. The use of parallelism is an effective approach to reduce the latency. To meet the requirement, an architecture of a new multiple-valued arithmetic VLSI processor is developed. In the processor, addition and subtraction are performed by using the single adderbased processing element (PE). More complex basic arithmetic operations such as multiplication and division are performed by the appropriate data communications between the adder-based PEs with preserving their parallelism. In the proposed architecture, fine-grain parallel processing at the adder-based PE level is realized, and all the PEs can be fully utilized for any parallel arithmetic operations according to adder-based data dependency graph. As a result, the processing speed will be greatly increased in comparison with the conventional parallel processors having the different kinds of the arithmetic PEs such as an adder, a multiplier and a divider. To realize the arithmetic VLSI processor using the adder-based PEs, we introduce the signed-digit (SD) number system for the parallel arithmetic operations because the SD arithmetic has the advantage of modularity as well as parallelism. The multiple-valued bidirectional currentmode technology is also used for the implementation of the compact and high-speed adder-based PE, and the reduction of the number of the interconnections. It is demonstrated that these advantges of the multiple-valued technology are fully used for the implementation of the arithmetic VLSI processor. As a result, the latency of the proposed multiple-valued processor is reduced to 25% that of the binary processor integrated in the same chip size.

Low-sensitivity digital filters are required for accurate signal processing. Among many low-sensitivity digital filters, a method using complex allpass circuits is well-known. In this paper, a new synthesis of complex allpass circuits is proposed. The proposed synthesis can be realized more easily either only in the z-domain or in the s-domain than conventional methods. The key concept for the synthesis is based on the factorization of lossless scattering matrices. Complex allpass circuits are interpreted as lossless digital two-port circuits, whose scattering matrices are factored. Furthermore, in the cases of Butterworth, Chebyshev and inverse Chebyshev responses, the explicit formulae for multiplier coefficients are derived, which enable us to synthesize the objective circuits directly from the specifications in the s-domain. Finally design examples verify the effectiveness of the proposed method.

Rapid advances in integrated circuit technology based on binary logic have made possible the fabrication of digital circuits or digital VLSI systems with not only a very large number of devices on a single chip or wafer, but also high-speed processing capability. However, the advance of processing speeds and improvement in cost/performance ratio based on conventional binary logic will not always continue unabated in submicron geometry. Submicron integrated circuits can handle multiple-valued signals at high speed rather than binary signals, especially at data communication level because of the reduced interconnections. The use of nonbinary logic or discrete-analog signal processing will not be out of the question if the multiple-valued hardware algorithms are developed for fast parallel operations. Moreover, in VLSI or ULSI processors the delay time due to global communications between functional modules or chips instead of each functional module itself is the most important factors to determine the total performance. Locally computable hardware implementation and new parallel hardware algorithms natural to multiple-valued data representation and circuit technologies are the key properties to develop VLSI processors in submicron geometry. As a result, multiple-valued VLSI processors make it possible to improve the effective chip density together with the processing speed significantly. In this paper, we summarize several potential advantages of multiple-valued VLSI processors in submicron geometry due to great reduction of interconnection and due to the suitability to locally computable hardware implementation, and demonstrate that some examples of special-purpose multiple-valued VLSI processors, which are a signed-digit arithmetic VLSI processor, a residue arithmetic VLSI processor and a matching VLSI processor can achieve higher performance for real-world computing system.

The main interest of this paper is the theoretical analysis of a recursive periodically time varying digital filter. The generalized transfer function of a recursive periodically time varying digital filter was obtained from its difference equation. It was proved that by making use of the generalized transfer function, we can not only derive the input and output relationship of a recursive periodically time varying digital filter easily but also obtain its equivalent structure effectively. An interesting property of a recursive periodically time varying digital filter was also derived by making use of its generalized transfer function. Moreover, it was completed in this paper the investigation of the generalized transfer functions and impulse responses of other periodically time varying models, including an input sampling polyphase model and an output sampling polyphase model. Meanwhile, the multirate Quadrature Mirror Filter bank system was proved by the authors to be a periodically time varying system. Several examples were also provided to illustrate the effectiveness of using the generalized transfer function to obtain the equivalent structure of a recursive periodically time varying digital filter.

A method is proposed for realizing any k-valued n-variable function with a celluler array, which consists of linear arrays (called input arrays) and a rectangular array (called control array). In this method, a k-valued n-variable function is divided into kn-1 one-variable functions and remaining (n1)-variable function. The parts of one-variable functions are realized by the input arrays, remaintng the (n1)-variable function is realized by the control array. The array realizing the function is composed by connecting the input arrays with the control array. Then, this array requires (kn2)kn-1 cells and the number is smaller than the other rectangular arrays. Next, a ternary cell circuit and a literal circuit are actually constructed with CMOS transistors and NMOS pass transistors. The experiment shows that these circuits perform the expected operations.

Robust-fault tolerance is a property that a computational result becomes nearly equal to the correct one at the occurrence of faults in digital system. There are many cases where the safety of digital control systems can be maintained if the property is satisfied. In this paper, robust-fault-tolerant three-valued arithmetic modules such as an adder and a multiplier are proposed. The positive and negative integers are represented by the number of 1's and 1's, respectively. The design concept of the arithmetic modules is that a fault makes linearly additive effect with a small value to the final result. Each arithmetic module consists of identical submodules linearly connected, so that multi-stage structure is formed to generate the final output from the last submodule. Between the input and output digits in the submodule some simple functional relation is satisfied with respect to the number of 1's and 1's. Moreover, the output digit value depends on very small portion of the submodules including the input digits. These properties make the linearly additive effect with a small value to the final result in the arithmetic modules even if multiple faults are occurred at the input and output of any gates in the submodules. Not only direct three-valued representation but also the use of three-valued logic circuits is inherently suitable for efficient implementation of the arithmetic VLSI system. The evaluation of the robust-fault-tolerant three-valued arithmetic modules is done with regard to the chip size and the speed using the standard CMOS design rule. As a result, it is made clear that the chip size can be greatly reduced.

This paper presents a VLSI-oriented arithmetic design method using a radix-2 redundant number representation with digit set {0, 1, 2} and multiple-valued current-mode (MVCM) circuit technology. We propose a carry-propagation-free (CPF) parallel addition method with redundant digit set {0, 1, 2} which is suitable for the design with MVCM circuits. Several types of CPF parallel adders are compared and the proposed CPF parallel adder with MVCM circuits offers the best total performance with respect to speed, complexity, and power dissipation. The designed basic arithmetic circuits has sufficient noise immunity to the supply voltage fluctuation which is important for stable operations of the VLSI circuits. The CPF parallel adder is effectively used as the reduction scheme of partial products in a high-speed compact multiplier. For example, the designed 3232 bit multiplier reduces the number of active elements to two-third and the number of interconnections to one-fifth of the corresponding binary Wallace tree multiplier, where the speed is almost the same. The structure is simple and regular. The static power dissipation of the designed 32-bit multiplier is estimated to be the mean value of 212 mW and the worst case of 708 mW. The total power including dynamic power dissipation would not be so large compared with that of the 32-bit binary CMOS multiplier reported under 10 MHz operation.

In this paper, two models for associative memory based on a measure of manhattan length are proposed. First, we propose the two-layered model which has an advantage to its implementation by using PDN. We also refer to the way to improve the recalling ability of this model against noisy input patterns. Secondly, we propose the other model which always recalls the nearest memory pattern in a measure of manhattan length by lateral inhibition. Even if a noise of input pattern is so large that the first model can not recall, this model can recall correctly against such a noisy pattern. We also confirm the performance of the two models by computer simulations.

A new class of the universal representation for the positive integers is proposed. The positive integers are divided into infinite groups, and each positive integer n is represented by a pair of integers (p,q), which means that n is the q-th number in the p-th group. It is shown that the new class includes the message length strategy as a special case, and the asymptotically optimal representation can easily be realized. Furthermore, a new asymptotically and practically efficient representation scheme is proposed, which preserves the numerical, lexicographical, and length orders.

In this paper, four simple nonlinear circuits with time-varying resistors are analyzed. These circuits consist of only four elements; a inductor, a capacitor, a diode and a time-varying resistor and are a kind of parametric excitation circuits whose dissipation factors vary with time. In order to analyze chaotic phenomena observed from these circuits a degeneration technique is used, that is, diodes in the circuits are assumed to operate as ideal switches. Thereby the Poincar maps are derived as one-dimensional maps and chaotic phenomena are well explained. Moreover, validity of the analyzing method is confirmed theoretically and experimentally.

This letter describes a new input and cross-point buffering matrix switching architecture for high-speed ATM switching systems. The proposed switch has input queuing buffers at each input port, and small size buffers for output port arbitration at each cross-point. These two types of buffers share loads using a simple and high-speed retry algorithm. Hardware size is only half that of conventional cross-point buffering switches. In addition, the switch achieves high-throughput at a condition that the switching speed matches the input and output port speed. This switch is expected to enable the development of high-speed ATM switching systems with each port supporting speeds in excess of 1Gbit/s.

A new method is proposed for automatically evaluating the English pronunciation quality of non-native speakers. It is assumed that pronunciation can be rated using three criteria: the static characteristics of phonetic spectra, the dynamic structure of spectrum sequences, and the prosodic characteristics of utterances. The evaluation uses speech recognition techniques to compare the English words pronounced by a non-native speaker with those pronounced by a native speaker. Three evaluation measures are proposed to rate pronunciation quality. (1) The standard deviation of the mapping vectors, which map the codebook vectors of the non-native speaker onto the vector space of the native speaker, is used to evaluate the static phonetic spectra characteristics. (2) The spectral distance between words pronounced by the non-native speaker and those pronounced by the native speaker obtained by the DTW method is used to evaluate the dynamic characteristics of spectral sequences. (3) The differences in fundamental frequency and speech power between the pronunciation of the native and non-native speaker are used as the criteria for evaluating prosodic characteristics. Evaluation experiments are carried out using 441 words spoken by 10 Japanese speakers and 10 native speakers. One half of the 441 words was used to evaluate static phonetic spectra characteristics, and the other half was used to evaluate the dynamic characteristics of spectral sequences, as well as the prosodic characteristics. Based on the experimental results, the correlation between the evaluation scores and the scores determined by human judgement is found to be 0.90.