A conflict detection support method for combining additional telecommunication services with existing services is proposed. In this method, telecommunication services are described by the STR (State Transition Rule) method which specifies a set of state transition rules. Though conflict detection in the past depended on manual analysis by the designer, with this method, conflict candidates are mechanically narrowed down and indicated to the designer. All conflicts between five actual telecommunication service descriptions are detected in an experiment using a system developed in line with the proposed method.

An effective bitline technique for high density DRAMs is studies. The open-type bitline structure where the bitlines are activated alternately can decrease the bitline noises and the current dissipation in memory cell arrays. In spite of several disadvantages inherent to the open-type bitline structure, this technique is found to get the larger read-out signal than the conventional bitline configurations for the DRAMs of 64 Mb and beyond. The effectiveness is confirmed with the measurement of the test-chips. This technique is expected to be more efficient for DRAMs of higher density, where the contribution of the inter-bitline capacitance is increased.

This paper deals with the sub-problems of generating a mask pattern from the logical description of a large-scale CMOS circuit. The large-scale layout can be generated in divide-and-conquer style: divide a given circuit into a set of sub-circuits, generate the layout of each sub-circuit, and merge the resulting layouts to create the whole layout. This paper proposes a layout synthesis algorithm for a sub-circuit with physical constraints for the synthesis scheme above. The physical constraints considered here are the relative placement of logic cells (sets of logic gates) and the routing constraint based on the costs of wiring layers and vias. These constraints will be given by the global optimizer in a two-dimensional layout synthesis routine, and they should be kept at the subsequent one-dimensional layout synthesis for a sub-circuit. The latter is also given for enhancing the circuit performance by limiting the usage of wiring layers and vias for special net such as a clock net. The placement constraint is maintained using PQ-tree, a tree structure representing a set of restricted permutations of elements. One-dimensional layout synthesis determines the placement of transistors by the enhanced pairwise exchanging method under the PQ-tree representation. The routing constraints is considered in the newly developed line-search routing method using a cost-based searching. Experimental results for practical standard cells, including up to 200 transistors, prove that the algorithms can produce the layouts comparable to handcrafted cells. Also on a two-dimensional layout synthesis using the algorithms, the results for benchmark circuits of Physical Design Workshop 1989, i.e., MCNC benchmark circuits, are superior to the best results exhibited at Design Automation Conference 1990.

Net-Oriented Analysis and Design (NOAD) is defined as three items: (1) Various nets are utilized as an effective modeling method. (2) Inter-relationships among verious nets are determined. (3) Verification or analysis methods for nets are provided and they are implemented based on the mathematical theory, that is Net theory. Very few methods have been presented to satisfy these three items. For example, the Real-Time SA method covers item (1) only. The Object-Oriented Analysis and Design method (OOA/OOD) covers items (1) and (2). NOAD can be regarded as an extension to OOA/OOD. This paper discusses how effectively various nets have been used in actual software development support metnods and tools and evaluates such several methods and tools from the NOAD viewpoint.

A film carrier with 48 peripheral-contacts, which is applicable to ultra-high speed GaAs digital integrated circuits (ICs) with a more than 10 Gbps operation, has been developed. The film carrier has been realized using the following newly developed techniques; (1) wave guides with a well-controlled characteristic impedance of 50 Ω, (2) precise vias of as small as 50 µm diameter conducting both sides of grounded metal planes on a polyimide film, and (3) a feed-through structure for high speed input signals with good impedance matching. The film carrier was molded by resin after ILB (inner lead bonding) to a chip with a copper plate heat spreader. As an application, the film carrier has been applied to a 3 Gbps operational 4-bit GaAs multiplexer IC, and has been proved to have excellent high-frequency characteristics.

An automatic macrocell generator has been developed and applied to the analog layout of SC and active-RC filters. The generator consists of a process independent generation procedure, a leafcell library, and a circuit description of the leafcells. The unit element arrays of the whole filter are generated together to minimize the array height of the entire filter macrocell, so that the area of the generated filter is as small as that of a manually laid out filter. Three SC filters and one active-RC filter were designed and fabricated by 1.5-µm CMOS technology, that successfully yielded an S/N ratio of more than 70 dB with a quick turn around time.

An autonatic layout scheme dedicated to bipolar analog modules is described. A layout model is settled in such a way that the VCC/GND line is laid out on top/bottom edge of a rectangular region, within which the whole elements are placed and interconnected. According to this simple modeling, a layout scheme can be constructed of a series of the following algorithms: First clustering is executed for partitioning a given circuit into clusters, each having connections with VCC and GND lines, and then linear ordering is applied to clusters so as to be placed in a one-dimensional array. After a relative placement of circuits elements in each cluster, a block compactor is implemented by means of packing blocks in each cluster into an idle space, and then a detailed router is conducted to attain 100% interconnection. Finally a layout compactor is invoked to pack all layout patterns into a rectangle of the minimum possible area. A number of implementation results are also shown to reveal the practicability of the proposed analog module generator.

This paper presents an efficient heuristic algorithm for min-cut bisection of weighted hypergraphs. The proposed algorithm is based on a heuristic algorithm proposed by Kahng, which was devised for non-weighted hypergraph bisection, adopting a non-weighted graph called intersection graph to represent a given hypergraph. In the proposed algorithm, instead of an intersection graph, a bipartite graph called netgraph is newly introduced to explicitly represent the weights of nodes of a hypergraph. Using the netgraph, it is easy to partition a weighted hypergraph into two hypergraphs with same size. Computation time of the proposed method is O(m2), where m is the number of nodes of a given hypergraph. Experimental results with real circuit data show that the proposed method produces better solutions in shorter computation time compared with existing methods.

The purpose of this paper is to propose a technique to simplify the communications software descriptions written in a procedural language in order to enhance their comprehensibility. Although such a technique was not much studied and discussed in the past, this technique is important to realize high productivity and high quality of the communications software by reducing the complexity of the software description. This paper firstly systematically presents various simplification methods with their principles for the descriptions of the communications software from the viewpoints of their layout, syntactical structures etc. Then, it describes a simplification support system based on these principles for the software specifications written in SDL. Lastly, this paper demonstrates the usefulness and effectiveness of the proposed simplification technique by analyzing the evaluation results of the simplification system.

Many practical communication protocols provide priority service as well as ordinary service. In such a protocol, the protocol machines can initiate a priority service at most of the states. This characteristic leads an extreme increment of the number of state transitions on the protocol machines and causes state space explosion in verification of safety property of the protocol. This paper describes a method of constructing a communication protocol from composition of a subprotocol for ordinary service and that for priority service. This paper also presents a sufficient condition for a composed protocol to inherit safety property from the subprotocols. By using the composition method and the sufficient condition, the decision problem for safety property of the composed protocol can be reduced to those of the subprotocols. An experimental result of verification of a part of OSI session protocol is also described. The result shows that the method can reduce the computation time for verifying safety property to about 3% against the naive way.

In LOTOS, requirements for a distributed system are described as a service definition. On the protocol level, each node (protocol entity) must exchange some data values and synchronization messages to provide a service described in a service definition. The tuple of the specifications of all nodes in the system which provide the service is called as a protocol specification. In order to develop the communication programs satisfying a given service definition, it is very important to develop the correct protocol specification. For this purpose, the simulation of protocol specifications is useful and it is desirable that the designer can observe how a protocol specification is executed in parallel and how synchronization messages are exchanged among the nodes. Therefore, we have developed a new tool named PROSPEX. For a given pair of a service definition and a protocol specification, it executes the protocol specification in parallel and shows its execution process graphically on X Window System. If the protocol specification executes an event sequence which does not satisfy the service definition, then PROSPEX informs it to the designer. In this paper, the design and usefulness of PROSPEX are described.

Public switching systems are intensively realtime and multi-processing, very large, long-lived, and frequently modified. Programs that control switching systems are therefore required not only to have run-time efficiency but also to be easy to maintain and extend. This paper proposes a Concurrent Object Model and an Object-Oriented Switching Program Structure. The Concurrent Object Model ensures simple and efficient real-time multi-processing. This model allows logical switching components to be implemented as "objects" in software, and the structure of the program coincides with the structure of the logical model. The program structure proposed here uses distributed call processing, which allows building-block-structured switching systems. A prototype switching program proved the effectiveness of this approach and showed that the static and dynamic overheads are within the capacity of present VLSI technology.

This paper describes the architecture and the performances of a GaAs 88 self-routing switch LSI for ATM switching system. The communication system such as broadband integrated sevices digital network (B-ISDN) requires the hardware switch LSI which exchanges packet cells at a date rate up to several Gb/s. GaAs LSIs are suitable for such application because of its high speed operation and low power dissipation. To clarify the feasibility of GaAs LSI, an 88 self-routing switch LSI is fabricated using 0.5 µm gate GaAs MESFETs and its oerformances are examined. This LSI consists of a switching network for exchanging the packet cells and the "NEMAWASHI" network which detects the cell destined to the same output port. The basic network architecture is a self-routing switch using Batcher-Banyan network. This network consists of basic 22 switch element. Since each element switches the route accorging to the destination of the input cells, self-routing operation is performed without the external circuit for routing control. The LSI is fabricated using 0.5 µm gate GaAs MESFETs. 7003 logic gate are integrated on the chip of 8.2 mm7.4 mm. To reduce the impedance of ground line on the chip and to obtain the enough noise margin, the third level interconnection with low sheet resistance is implemented. As the results of functional evalution, the full function of switching network and "NEMAWASHI" network are verified. Maximum operation speed of 1 GHz is obtained.

A job shop system typically seen in flexible manufacturing systems (FMS) is a system composed of a set of machines and a various kind of jobs processed with the machines. A production system of semiconductor fabrication is an example of job shop systems, which has main features of repetitive processes of one part and set-up times required for machines processing different types of parts. On the other hand, timed Petri nets are used for modelling and analyzing a wide variety of discrete event systems. There are many applications of timed Petri nets to the scheduling problems of job shop systems. The performance evaluation and steady state behaviors are studied by using the maximum cycle time of timed marked graphs. The aim of this paper is to propose a new model for production systems including repetitive processes and set-up time requirements which enables the quantitative analysis of real time system performance. In job shop systems such as a semiconductor fabrication system, it takes considerable amount of set-up time to prepare different types of chemical reactions and the model should take account of a set-up time for each machine. We focus upon the relationship between facility utilization factor and production cycle time in the steady state. In the proposed model, the minimum total set-up time can be attained. Quantitative relationship between utilization factor and production cycle time is derived by using the proposed model. A utilization factor of a system satisfying a given limit of the cycle time is evaluated, and the improvement of the utilization factor is considered. Conversely, we consider the improvement of the cycle time of a system satisfying a given limit of utilization factor.

The preparation of magnetic semiconductor thick film (MST) by means of spray printing and application to a temperature/gas/essence sensor have been proposed. The MST pattern is composed of ferrite, ruthenium compound, carbon black, binder and solvent. After the mixed mgnetic semiconductor fluid is sprayed on a substrate, the sample is sintered at 750. The MST with thickness of 40 µm is printed on the substrate in various shapes such as a plate, a ring or a rod. The magnetic property of MST depends on temperature, and the electrical property responds to gas and natural/artificial fruit essence. Therefore, the multipore ceramic MST operates as a gas sensor with high sensitivity and high stability.

In this paper we propose a new timing verification technique named coded time-symbolic simulation, CTSS. Our interest is on simulation of logic circuits consisting of gates whose delay is specified only by its minimum and maximum values. Conventional logic simulation based on min/max delay model leads to over-pessimistic results. In our new method, the cases of possible delay values of each gate are encoded by binary vectors. The circuit behavior for all the possible combinations of the delay values are simulated based on symbolic simulation by assigning Boolean variables to the binary vectors. This simulation technique can deal with logic circuits containing feedback loops as well as combinational circuits. We implemented an efficient simulator by using shared binary decision diagrams (SBDD's) as internal representation of Boolean functions. We also propose novel techniques of analyzing the results of CTSS.

This paper presents the EXM-algorithm, which locates multiple logic design errors in a combinational circuit with multiple output. The error possibility index and the six-valued simulation method have been enhanced to be applied to multiple output circuit. The algorithm locates multiple errors even if they belong to different cone circuits, and processes faster than the conventional EX-algorithm for circuits with the similar gate sizes. Experimental results have shown that the algorithm locates all errors at high hit ratio for ISCAS benchmark circuits and some other circuits.

This paper presents unique specification environments for LOTOS, which is one of FDTs (Formal Description Techniques) developed in ISO. We first discuss the large gap in terms of syntax and semantics between informal specifications at the early stage of specification design and formal specifications based on FDT such as LOTOS. This large gap has been bridged by human intelligent works thus far. In order to bridge the large gap, we have designed user-friendly specification environments for FDTs. The outlines of SEGL (Specification Environment for G-LOTOS), CBP (Concept-Based Programming environment) and MBP (Model-Based Programming environment) are described. The effectiveness of software development under such an environment is demonstrated using application examples from OSI and non-OSI protocols.

This paper surveys modeling techniques for telephone call control based on a Finite State Machine (FSM) concept, and studies model simplification techniques. First, the basic concept and fundamental issues of call control modeling are described. Then, based on the analysis of layered call control configuration, it is clarified that the call control machine decomposition within the two-party service control layer has the effect of reducing the apparent size of each mate's machine. Using this effect, guidelines for call control modeling are derived, by which multiple services can be modeled independently. Finally implementation techniques and a few examples of application will be presented.

In this paper, the software structure for telecommunication user support are discussed, and it is proposed to apply knowledge processing technology to the software. Capabilities of telecommunications networks are becoming quite complicated, and the number of service items and parameters which have to be selected and memorized will become too large for telecommunications end users to make full use of the network capabilities. As such, more effort should be focused on assisting telecommunications end users to use the network and providing user friendly human interfaces of the network. However, this kind of software has additional type of requirements other than those for protocol handling software and call control software, and the realization of such support software has not yet been fully studied. To realize such support software, this paper stressed the realization of the user-system interface. Especially identified in this paper are meaning-based interpretation of user inputs to permit the handling of synonyms and multivocations, and a method to access the database in the support system without consideration of its data schema. To satisfy these objectives, this paper has proposed that the application data should be represented in both a character string and a meaning representation, and that the thesauruses should have the attribute-value relation. In line with these studies, an experimental system called CAPRIS (CAlling PRocedure Instruction System) was developed. It is used to assist the calling party in a telecommunications network to find an appropriate contact point depending on the purpose of the communication. Implementation of CAPRIS is completed and it was confirmed that all the functions described in this paper were actually realized. Some functional experiments were performed on CAPRIS, and the system was concluded to realize satisfactory user-friendliness.