Fuminori SAKAI Mitsuo MAKIMOTO Koji WADA
Chipless RFID tags that use the higher-mode resonances of a transmission line resonator are presented in this paper. We have proposed multimode stepped impedance resonators (SIRs) for this application and reported the fundamental characteristics of an experimental system composed of multimode SIRs with open-circuited ends and a near-field electromagnetic detector using capacitive coupling (electric field) probes for the detector. To improve the frequency response and widen the detection range, we introduced multimode SIRs with short-circuited ends and inductive coupling (magnetic field) probes and measured their properties. To reduce the size of the tag and reader, we examined the frequency responses and found that the optimal configuration consisted of C-shaped tags and detector probes with a spatially orthogonal arrangement. The experimental tag system showed good frequency responses, detection range, and frequency detection accuracy. In particular, the spacing between the tag resonator and the transmission line of the probe, which corresponds to the detection distance, was 5mm or more, and was at least 10 times greater than that of previously reported RFID tag systems using near-field electromagnetic coupling.
This paper presents a simple method for comparing the impedance of an artificial mains network (AMN) with the International Special Committee on Radio Interference (CISPR) 16-1-2 standard. The circuit of a vector network analyzer, which is an impedance measurement instrument, is not ideal, and the measured impedances include measurement uncertainties. However, complete uncertainty analysis is not required in the proposed method. By comparing the relative relationship between the measured impedance of an AMN under test and the measured impedance of the original transfer standards whose impedance is modeled by the regulated impedance in the CISPR 16-1-2 standard, conformity to the standard can be determined. The magnitude and phase of the impedance of an AMN can be independently analyzed. To demonstrate the method, we apply it to a commercially available AMN. The comparison result is found to be equivalent to the result based on a complete uncertainty analysis, which confirms that the proposed comparison method is feasible.
Marco FAENZI Gabriele MINATTI Stefano MACI
This paper gives an overview on the design process of modulated metasurface (MTS) antennas and focus on their performance in terms of efficiency and bandwidth. The basic concept behind MTS antennas is that the MTS imposes the impedance boundary conditions (IBCs) seen by a surface wave (SW) propagating on it. The MTS having a spatially modulated equivalent impedance transforms the SW into a leaky wave with controlled amplitude, phase and polarization. MTS antennas are hence highly customizable in terms of performances by simply changing the IBCs imposed by the MTS, without affecting the overall structure. The MTS can be configured for high gain (high aperture efficiency) with moderate bandwidth, for wide bandwidth with moderate aperture efficiency, or for a trade-off performance for bandwidth and aperture efficiency. The design process herein described relies on a generalized form of the Floquet wave theorem adiabatically applied to curvilinear locally periodic IBCs. Several technological solutions can be adopted to implement the IBCs defined by the synthesis process, from sub-wavelength patches printed on a grounded slab at microwave frequencies, to a bed of nails structure for millimeter waves: in any case, the resulting device has light weight and a low profile.
Bingting WANG Ziping CAO Song SHI Shaoteng GAO
Impedance mismatching is a major obstacle hindering the application of DC power line communication (DC-PLC) due to the unpredictability of access impedance and random loads. Researchers and manufacturers typically estimate the power line impedance level and use a fixed single-winding coupler to carry out signal coupling, which does not achieve accurate impedance matching and leads to large signal attenuation and low reliability. In this paper, a lumped parameter power line communication model for DC-PLC is established in which the optimal receiver winding ratio is derived from equivalent circuits. A modifiable impedance matching coupler was designed to achieve dynamic impedance matching, and a series of simulations were run to analyze the relationship among optimal winding ratio, power line impedance and series loads. The performance of different winding ratio couplers under varied frequency and load impedance was also measured in a laboratory environment to find that adopting the modifiable impedance matching coupler is indeed a useful strategy for achieving adaptive impedance matching with maximum signal power transfer.
Shuenn-Yuh LEE Cheng-Pin WANG Chuan-Yu SUN Po-Hao CHENG Yuan-Sun CHU
This study proposes a multiple-output differential-input operational transconductance amplifier-C (MODI OTA-C) filter with an impedance scaler to detect cardiac activity. A ladder-type fifth-orderButterworth low-pass filter with a large time constant and low noise is implemented to reduce coefficient sensitivity and address signal distortion. Moreover, linearized MODI OTA structures with reduced transconductance and impedance scaler circuits for noise reduction are used to achieve a wide dynamic range (DR). The OTA-based circuit is operated in the subthreshold region at a supply voltage of 1 V to reduce the power consumption of the wearable device in long-term use. Experimental results of the filter with a bandwidth of 250 Hz reveal that DR is 57.6 dB, and the harmonic distortion components are below -59 dB. The power consumption of the filter, which is fabricated through a TSMC 0.18 µm CMOS process, is lower than 390 nW, and the active area is 0.135 mm2.
Wireless power transfer (WPT) via coupled magnetic resonances has more than ten years history of development. However, it appears frequency splitting phenomenon in the over-coupled region, thus, the output power of the two-coil WPT system achieves the maximum output power at the two splitting angular frequencies and not at the natural resonant angular frequency. By investigating the relationship between the impedances of the transmitter side and receiver side, we found that WPT system is a power superposition system, and the reasons were given to explaining how to appear the frequency splitting and impact on the maximum output power of the system in details. First, the circuit model was established and transfer characteristics of the two-coil WPT system were studied by utilizing circuit theories. Second, the mechanism of the power superposition of the WPT system was carefully researched. Third, the relationship between the impedances of the transmitter side and receiver side was obtained by investigating the impedance characteristics of a two-coil WPT system, and also the impact factors of the maximum output power of the system were obtained by using a power superposition mechanism. Finally, the experimental circuit was designed and experimental results are well consistent with the theoretical analysis.
A frequently occurring subcircuit consists of a loop of a resistor (R), a field-effect transistor (FET), and a capacitor (C). The FET acts as a switch, controlled at its gate terminal by a clock voltage. This subcircuit may be acting as a sample-and-hold (S/H), as a passive mixer (P-M), or as a bandpass filter or bandpass impedance. In this work, we will present a useful analysis that leads to a simple signal flow graph (SFG), which captures the FET-R-C circuit's action completely across a wide range of design parameters. The SFG dissects the circuit into three filtering functions and ideal sampling. This greatly simplifies analysis of frequency response, noise, input impedance, and conversion gain, and leads to guidelines for optimum design. This paper focuses on the analysis of a single-path FET-R-C circuit's signal transfer characteristics including the reconstruction of the complete waveform from the discrete-time sampled voltage.
Nozomi HAGA Masaharu TAKAHASHI
The impedance expansion method (IEM), which has been previously proposed by the authors, is a circuit-modeling technique for electrically-very-small devices. This paper provides a new idea on the principle of undesired radiation in wireless power transfer systems by employing IEM. In particular, it is shown that the undesired radiation is due to equivalent infinitesimal dipoles and loops of the currents on the coils.
Nozomi HAGA Masaharu TAKAHASHI
The impedance expansion method (IEM), which was previously proposed by the authors, is a circuit-modeling technique for electrically-very-small devices. The equivalent circuits derived by the IEM include dependent voltage sources proportional to the powers of the frequency. However, the previous report did not describe how circuit simulators could realize such dependent voltage sources. This paper shows how this can be achieved by approximating the equivalent circuit using only passive elements.
Nozomi HAGA Masaharu TAKAHASHI
This paper proposes a circuit modeling technique for electrically-very-small devices, e.g. electrodes for intrabody communications, coils for wireless power transfer systems, high-frequency transformers, etc. The proposed technique is based on the method of moments and can be regarded as an improved version of the partial element equivalent circuit method.
Xianliang LUO Yingmei CHEN Mohamed ATEF Guoxing WANG
This paper presents a 44 Gbit/s Transimpedance Amplifier (TIA) with wide-dynamic range and high-linearity for optical receiver fabricated in 130 nm BiCMOS technology. The TIA has the features of 67dBΩ overall transimpedance gain, a bandwidth of 28GHz, 10pA/√Hz of Input Referred Noise Current Power Spectral Density (IRNCPSD), and a power consumption of 95mW from a 2.5V supply. The Total Harmonic Distortion (THD) is less than 5% for a differential input current up to 2.63mApp, when the static input current is 0.1mA.
Hideki KIRINO Kazuhiro HONDA Kun LI Koichi OGAWA
A new Waffle-iron Ridge Guide (WRG) structure that has the ability to control both wavelength and impedance is proposed. With the proposed structure, not only can the wavelength be controlled over a wide range for both fast- and slow-waves in free space but the impedance can also be controlled. These features can improve the performance of array antennas in terms of reducing grating lobes and side lobes. In this paper, we discuss and evaluate a design scheme using equivalent circuits and EM-simulation. This paper also discusses how the conductivity and dielectric loss in the WRG affect the total gain of the array antenna.
Sonshu SAKIHARA Satoshi KITABAYASHI Naoki SAKAI Takashi OHIRA
This paper presents a novel circuit for impedance matching to a load moving along a transmission line. This system is called FERMAT: Far-End Reactor MATching. The FERMAT consists of a power transmission line and a variable reactor at its far-end. The proposed system moves standing-wave antinodes to the position of the vehicle in motion. Therefore, the moving vehicle can be fed well at any position on the line. As a theoretical result, we derive adjustable matching conditions in FERMAT. We verified that the experimental result well agrees with the theory.
Kyoichi IIGUSA Hirokazu SAWADA Fumihide KOJIMA Hiroshi HARADA
We propose a wideband antenna that has both vertical and horizontal polarization to create access points with enhanced connectivity. The antenna is composed of a rectangular plate and a ground plate, and the rectangular plate is fed sideways from the ground plate. Its -10dB fractional bandwidth is approximately 162%. It is shown that the offset feed of the rectangular plate is important to attain wideband impedance matching and vertical polarized wave. The results of a parametric study to characterize the first- and second-lowest resonant frequencies are presented. Moreover, the behavior of the impedance matching and polarization is interpreted by dividing the current distribution around the feed port on the rectangular plate into the same direction current mode and the opposite direction current mode. The measured results for the return loss and the radiation pattern of a prototype antenna agree well with the simulation results, therefore the wideband property was experimentally confirmed.
Sonshu SAKIHARA Masaru TAKANA Naoki SAKAI Takashi OHIRA
This paper presents an approach to nonlinear impedance measurement exploiting an oscilloscope and Möbius transformation. Proposed system consists of a linear 4-port network and an oscilloscope. One of the port is excited by a high power source. The power is delivered to the second port, which is loaded with a DUT. Another set of two ports are used to observe a voltage set. This voltage set gives the impedance of the DUT through Möbius transformation. We formulated measurability M of the system, and derived the condition that M becomes constant for any DUT. To meet the condition, we propose a linear 4-port network consisting of a quarter-wavelength transmission line and resistors. We confirm the validity and utility of the proposed system by measuring the impedance of incandescent bulbs and an RF diode rectifier.
Takashi YANAGI Toru FUKASAWA Hiroaki MIYASHITA
In this paper, a measurement method for the impedance and mutual coupling of multi-antennas that we have proposed is summarized. Impedance and mutual coupling characteristics are obtained after reducing the influence of the coaxial cables by synthesizing the measured S-parameters under the condition that unbalanced currents on the outside of the coaxial cables are canceled at feed points. We apply the proposed method to two closely positioned monopole antennas mounted on a small ground plane and demonstrate the validity and effectiveness of the proposed method by simulation and experiment. The proposed method is significantly better in terms of the accuracy of the mutual coupling data. In the presented case, the errors at the resonant frequency of the antennas are only 0.5dB in amplitude and 1.8° in phase.
The most commonly used scattering parameters (S parameters) are normalized to a real reference resistance, typically 50Ω. In some cases, the use of S parameters normalized to some complex reference impedance is essential or convenient. But there are different definitions of complex-referenced S parameters that are incompatible with each other and serve different purposes. To make matters worse, different simulators implement different ones and which ones are implemented is rarely properly documented. What are possible scenarios in which using the right one matters? This tutorial-style paper is meant as an informal and not overly technical exposition of some such confusing aspects of S parameters, for those who have a basic familiarity with the ordinary, real-referenced S parameters.
Kyohei YAMADA Naoki SAKAI Takashi OHIRA
Internal power losses in lumped-element impedance matching circuits are formulated by means of Q factors of the elements and port impedances to be matched. Assuming that Q factors are relatively high, the above mentioned loss is expressed by a simple formula containing only the tangents of the impedances. The formula is a powerful tool for such applications that put emphasis on power efficiency as wireless power transfer. As well as the formulation, we illustrate some design examples with the derived formula: design of the least lossy L-section circuit and two-stage low-pass ladder. The examples provide ready-to-use knowledge for low-loss matching design.
Takaho SEKIGUCHI Yoshinobu OKANO Satoshi OGINO
Near field communication (NFC) antennas are often lined with magnetic sheets to reduce performance degradation caused by nearby metal objects. Though amorphous sheets have a high permeability and are suitable magnetic sheets for lining, their magnetic loss is also high. Therefore, this paper suggests a technique of suppressing magnetic loss by modifying the shape of the sheet without changing its composition. The utility of the proposed technique was investigated in this study.
This paper presents an innovative fabrication process for a planar circuits at millimeter-wave frequency. Screen printing technology provides low cost and high performance coplanar waveguides (CPW) lines in planar devices operated at millimeter-wave frequency up to 110GHz. Printed transmission lines provide low insertion losses of 0.30dB/mm at 110GHz and small return loss like as impedance standard lines. In the paper, Multiline Thru-Reflect-Line (TRL) calibration was also demonstrated by using the impedance standard substrates (ISS) fabricated by screen printing. Regarding calibration capability validation, verification devices were measured and compare the results to the result obtained by the TRL calibration using commercial ISS. The comparison results obtained by calibration of screen printing ISS are almost the same as results measured based on conventional ISS technology.