This paper presents a nonlinear model of human brain activity in response to visual stimuli according to Blood-Oxygen-Level-Dependent (BOLD) signals scanned by functional Magnetic Resonance Imaging (fMRI). A BOLD signal often contains a low frequency signal component (trend), which is usually removed by detrending because it is considered a part of noise. However, such detrending could destroy the dynamics of the BOLD signal and ignore an essential component in the response. This paper shows a model that, in the absence of detrending, can predict the BOLD signal with smaller errors than existing models. The presented model also has low Schwarz information criterion, which implies that it will be less likely to overfit the experimental data. Comparison between the various types of artificial trends suggests that the trends are not merely the result of noise in the BOLD signal.

Two-track squeeze and adjacent track interference (ATI) are major barriers to increasing track density in hard disk drives (HDD). These depend on skew angles made by a magnetic head and circumferential direction on a magnetic disk. This paper describes relationships between the skew angle and the magnetic core width (MCW) which affects two-track squeeze and ATI performance. We propose a design concept of a track pitch profile at different skew angles considering MCW. Equivalent robustness of ATI performance on different skew angle conditions is obtained with the optimized track pitch.

Copper arc runners are fixed on silver electrical contacts. Break arcs are generated between the contacts in a DC resistive circuit. Circuit current when contacts are closed is 10A. Supply voltage is changed from 200V to 450V. The following results are shown. Cathode spots stay on the cathode surface but anode spots run on the runner when the supply voltage is 250V and over. In cases of the supply voltage is greater than 250V, the break arcs run on the runner when the arcs are successfully extinguished, and stays on the runner in cases of the failure of arc extinction. The arc lengths just before arc extinction with or without the runners are also investigated. The arc lengths are the same with or without the runners for each supply voltage.

In this study, we propose a two-step approach to evaluate electromagnetic interference (EMI) with a wearable vital signal sensor. The two-step approach combines a quasi-static electromagnetic (EM) field analysis and an electric circuit analysis, and is applied to the EMI evaluation at frequencies below 1 MHz for our developed wearable electrocardiogram (ECG) to demonstrate its usefulness. The quasi-static EM field analysis gives the common mode voltage coupled from the incident EM field at the ECG sensing electrodes, and the electric circuit analysis quantifies a differential mode voltage at the differential amplifier output of the ECG detection circuit. The differential mode voltage has been shown to come from a conversion from the common mode voltage due to an imbalance between the contact impedances of the two sensing electrodes. When the contact impedance is resistive, the induced differential mode voltage increases with frequency up to 100kHz, and keeps constant after 100kHz, i.e., exhibits a high pass filter characteristic. While when the contact impedance is capacitive, the differential mode voltage exhibits a band pass filter characteristic with the maximum at frequency of around 150kHz. The differential voltage may achieve nearly 1V at the differential amplifier output for an imbalance of 30% under 10V/m plane-wave incident electric field, and completely mask the ECG signal. It is essential to reduce the imbalance as much as possible so as to prevent a significant interference voltage in the amplified ECG signal.

This paper provides a method based on electromagnetic (EM) analysis to predict conducted currents in the bulk current injection (BCI) test system for automotive components. The BCI test system is comprised of an injection probe, equipment under test (EUT), line impedance stabilization networks (LISNs), wires and an electric load. All components are modeled in full-wave EM analysis. The EM model of the injection probe enables us to handle multi wires. By using the transmission line theory, the BCI setup model is divided into several parts in order to reduce the calculation time. The proposed method is applied to an actual BCI setup of an automotive component and the simulated common mode currents at the input terminals of EUT have a good accuracy in the frequency range of 1-400MHz. The model separation reduces the calculation time to only several hours.

In 1919 the Department of Electrical Engineering (EE) was established in Tohoku University (at that time, Tohoku Imperial University). In this Department a growing tendency towards research featured in science and technology for electrical communication. Great efforts made in these fields produced pioneering studies such as those of the Yagi-Uda antenna and slotted-anode type magnetrons in the late 1920s. The purpose of this article is to introduce the history of development of microwave electron-tube at Tohoku University, which was started with the Okabe's magnetron.

Electromagnetic analysis (EMA) against public-key cryptographic software on an embedded OS is presented in this paper. First, we propose a method for finding an observation point for EMA, where the EM radiation caused by cryptographic operations can be observed with low noise. The basic idea is to find specific EM radiation patterns produced by cryptographic operations given specific input pattern. During the operations, we scan the surface of the target device(s) with a micro magnetic probe. The scan is optimized in advanced using another compatible device that has the same central processing unit (CPU) and OS as the target device. We demonstrate the validity of the proposed EMAs through some EMA experiments with two types of RSA software on an embedded OS platform. The two types of RSA software have different implementations for modular multiplication algorithms: one is a typical and ready-made implementation using BigInteger class on Java standard library, and another is a custom-made implementation based on the Montgomery multiplication algorithm. We conduct experiments of chosen-message EMA using our scanning method, and show such EMAs successfully reveal the secret key of RSA software even under the noisy condition of the embedded OS platform. We also discuss some countermeasures against the above EMAs.

This paper shows that the induced peak voltage on the short monopole antenna by the EM field radiated from a small gap discharge when the gap width was experimentally changed from 10 to 360µm was not directly proportional to the discharge voltage between the gap. It was found that the 10mm short monopole antenna induced peak voltage had a peak value between 40 and 60µm gap width.

In this paper the amplitude probability distribution (APD) measurement method is applied to evaluate noise coupling to an antenna on an evaluation board that uses mixed RF and digital signals of an IC. We analytically investigate noise coupling path to the antenna where the correlation coefficient matches the APD curve of the evaluation board. Moreover, in order to verify the analysis results, the noise coupling path in the board is evaluated by measurements involving In-phase/Quadrature (I/Q) signals as well as electromagnetic simulations. As a result, we demonstrate that APD method is effective in evaluating a degree of noise coupling from an IC to multiple antennas on the board, and confirm that the intensity of noise coupling to each antenna is affected greatly by the board layout patterns.

This paper presents a method for evaluating the maximum bit error probability (BEP) of a digital communication system subjected to interference by measuring the amplitude probability distribution (APD) of the interfering noise. Necessary conditions for the BEP evaluation are clarified both for the APD measuring receiver and the communication receiver considered. A method of defining emission limits is presented in terms of APD so that the worst BEP of a communication system does not exceed a required permissible value. The methods provide a theoretical basis for a wide variety of applications such as emission requirements in compliance testing, dynamic spectrum allocations, characterization of an electromagnetic environment for introducing new radio systems, and evaluation of intra-system interference.

This paper proposed patient friendly capsule endoscopy (CE) for not only screening but also treatment. Two different types of CEs with an Internet utility were investigated. The first type used magnetic navigation in the stomach and colon for screening. Magnetic navigation enabled the capsule to explore the whole of the gastrointestinal tract with less risk of missing lesions and complete the screening within the battery life. The system's design was patiently friendly as it allowed the subjects to leave the hospital after the capsule had been navigated in the stomach. The second investigated two different therapeutic robotic endoscopes. Both prototypes were driven by DC motors and controlled remotely via the internet. In addition, they were equipped with therapeutic tools and each prototype's ability with the tools was assessed. The investigation showed it was possible to remotely control both prototypes and operate therapeutic tools via the Internet. The investigation identified areas for improvement, such as size, connection speed, security of data, and the holding the capsule's position during treatment, In conclusion, both methods have the potential to make capsule endoscopy a very patient friendly procedure that can be carried out anywhere.

Forty years after the first application of Superconducting Quantum Interference Devices (SQUIDs) [1], [2] for geophysical purposes, they have recently become a valued tool for mineral exploration. One of the most common applications is time domain (or transient) electromagnetics (TEM), an active method, where the inductive response from the ground to a changing current (mostly rectangular) in a loop on the surface is measured. After the current in the transmitter coil is switched, eddy currents are excited in the ground, which decay in a manner dependent on the conductivity of the underlying geologic structure. The resulting secondary magnetic field at the surface is measured during the off-time by a receiver coil (induced voltage) or by a magnetometer (e.g. SQUID or fluxgate). The recorded transient signal quality is improved by stacking positive and negative decays. Alternatively, the TEM results can be inverted and give the electric conductivity of the ground over depth. Since SQUIDs measure the magnetic field with high sensitivity and a constant frequency transfer function, they show a superior performance compared to conventional induction coils, especially in the presence of strong conductors. As the primary field, and especially its slew rate, are quite large, SQUID systems need to have a large slew rate and dynamic range. Any flux jump would make the use of standard stacking algorithms impossible. IPHT and Supracon are developing and producing SQUID systems based on low temperature superconductors (LTS, in our case niobium), which are now state-of-the-art. Due to the large demand, we are additionally supplying systems with high temperature superconductors (HTS, in our case YBCO). While the low temperature SQUID systems have a better performance (noise and slew rate), the high temperature SQUID systems are easier to handle in the field. The superior performance of SQUIDs compared to induction coils is the most important factor for the detection of good conductors at large depth or ore bodies underneath conductive overburden.

Electrostatic discharge (ESD) generators cause electromagnetic (EM) noises not only at ESD tests but also even before and after the tests. This may provide inconsistent test results, but the mechanism has not been well examined. To explain the mechanism qualitatively, we investigated a generation source model of EM noises from an ESD generator in conjunction with the functional control sequences of built-in relay switches and the DC high voltage power supply. To validate this model, we used a magnetic field probe to measure the induced EM noises before, during, and after contact and air discharges in accordance with the corresponding timing of the functional control sequences. As a result, we confirmed that the EM noises are induced when the relay switches operate before and at ESD testing and after ESD tests for both contact and air discharges. In addition, we found that the noise peaks due to contact discharges increase with charge voltages, and the peaks just before and at the testing are relatively larger than the ones after the tests, while the peaks of the induced noises at the air discharge testing do not always increase with charge voltages, but reach a maximum at 3kV. In addition, the peaks of the induced noises at the air discharge testing become smaller than either the peaks just before the testing and those after the tests at charge voltages above 6kV. This suggests that the EM noises just before ESD testing and after the test may cause the EUT to malfunction when air discharge tests with charge voltages over 6kV are conducted. A new control sequence of the built-in relay switch was also proposed for reducing the EM noises after ESD tests, which was validated through noise measurements.

To determine the thickness from MR images, segmentation, that is, boundary detection, of the two adjacent thin structures (e.g., femoral cartilage and acetabular cartilage in the hip joint) is needed before thickness determination. Traditional techniques such as zero-crossings of the second derivatives are not suitable for the detection of these boundaries. A theoretical simulation analysis reveals that the zero-crossing method yields considerable biases in boundary detection and thickness measurement of the two adjacent thin structures from MR images. This paper studies the accurate detection of hip cartilage boundaries in the image plane, and a new method based on a model of the MR imaging process is proposed for this application. Based on the newly developed model, a hip cartilage boundary detection algorithm is developed. The in-plane thickness is computed based on the boundaries detected using the proposed algorithm. In order to correct the image plane thickness for overestimation due to oblique slicing, a three-dimensional (3-D) thickness computation approach is introduced. Experimental results show that the thickness measurement obtained by the new thickness computation approach is more accurate than that obtained by the existing thickness computation approaches.

The reliability of electromagnetic relay (EMR) which contains a permanent magnet (PM) can be improved by a robust design method. In this parameter design process, the calculation of electromagnetic system is very important. In analytical calculation, PM is often equivalent to a lumped parameter model of one magnetic resistance and one magnetic potential, but significant error is often caused; in order to increase the accuracy, a distributed parameter calculation model (DPM) of PM bar is established; solution procedure as well as verification condition of this model is given; by a case study of the single PM bar, magnetic field lines division method is adopted to build the DPM, the starting point and section magnetic flux of each segment are solved, a comparison is made with finite element method (FEM) and measured data; the accuracy of this magnetic field line based distributed parameter model (MFDPM) in PM bar is verified; this model is applied to the electromagnetic system of a certain type EMR, electromagnetic system calculation model is established based on MFDPM, and the static force is calculated under different rotation angles; compared with traditional lumped parameter model and FEM, it proves to be of acceptable calculation accuracy and high calculation speed which fit the requirement of robust design.

In this paper, we propose a new design technique called extit{asynchronous multi-frequency clocking} for suppressing EMI at a chip design level by combining two independent EMI-suppressing approaches: extit{multi-frequency clocking} and extit{asynchronous circuit design} techniques. To show the effectiveness of our approach, a five-stage pipelined asynchronous MIPS with multi-frequency clocking has been implemented on a commercial Xilinx FPGA device. Our approach shows 11.05 dB and 5.88 dB reductions of peak EM radiation in the prototyped implementation when compared to conventional synchronous and bundled-data asynchronous circuit counterparts, respectively.

This paper proposes a background noise estimation method using an outer product expansion with non-linear filters for ELF (extremely low frequency) electromagnetic (EM) waves. We proposed a novel source separation technique that uses a tensor product expansion. This signal separation technique means that the background noise, which is observed in almost all input signals, can be estimated using a tensor product expansion (TPE) where the absolute error (AE) is used as the error function, which is thus known as TPE-AE. TPE-AE has two problems: the first is that the results of TPE-AE are strongly affected by Gaussian random noise, and the second is that the estimated signal varies widely because of the random search. To solve these problems, an outer product expansion based on a modified trimmed mean (MTM) is proposed in this paper. The results show that this novel technique separates the background noise from the signal more accurately than conventional methods.

Arterial spin labeling (ASL) is a non-invasive magnetic resonance imaging (MRI) method that can provide direct and quantitative measurements of cerebral blood flow (CBF) of scanned patients. ASL can be utilized as an imaging modality to detect Alzheimer's disease (AD), as brain atrophy of AD patients can be revealed by low CBF values in certain brain regions. However, partial volume effects (PVE), which is mainly caused by signal cross-contamination due to voxel heterogeneity and limited spatial resolution of ASL images, often prevents CBF in ASL from being precisely measured. In this study, a novel PVE correction method is proposed based on pixel-wise voxels in ASL images; it can well handle with the existing problems of blurring and loss of brain details in conventional PVE correction methods. Dozens of comparison experiments and statistical analysis also suggest that the proposed method is superior to other PVE correction methods in AD diagnosis based on real patients data.

A simple, low reflection, and highly-efficient pilot-plant scale microwave irradiation reactor for woody biomass pretreatment was fabricated. Pretreatment is an essential process for effective bioethanol production. The fabricated reactor consists of 8 microwave irradiators which are attached to a metal pipe. The woody biomass mixture which contains water and organic acid flows through the metal pipe and is heated by microwaves at a total power of 12,kW. To design the microwave irradiators, we used a 3D Finite Element Method (FEM) simulator, which was based on the measured complex permittivity data of the woody biomass mixture. The simulation results showed that the reflection coefficient $|S_{11}|$ from the reactor was less than -30,dB when the woody biomass mixture temperature was between 30$^{circ}$C and 90$^{circ}$C. Finally, we experimentally confirmed that the fabricated irradiation reactor yielded a microwave absorption efficiency of 79%.

This paper proposes a sector base station antenna for mobile wireless communication systems employing multiple woodpile metamaterial reflectors and a multiband radiator that establishes the same beamwidth in the horizontal plane for more than two frequency bands. Electromagnetic Band Gap (EBG) characteristics of each metamaterial reflector can be controlled through structural parameters of the woodpile reflector, e.g., the rod width and rod spacing. As an example of the proposed antenna, a design for a triple-frequency-band antenna that radiates at 800 MHz, 2,GHz, and 4,GHz is shown. The algorithm used to adjust the beamwidth of the proposed antenna is newly introduced and adjusts the beamwidth to be the same for each band using the rod width of the woodpile. A prototype of the proposed antenna has the approximately 90$^{circ}$ beamwidth in the horizontal plane at the three frequencies, and the measurement results agree well with the electromagnetic field simulation results.