A striped inductor and its utilization of a voltage-controlled oscillator (VCO) are studied with the aim of suppressing phase noise degradation in K- and Ka-bands. The proposed striped inductor exhibits reduced series resistance in the high frequency region by increasing the cross-sectional peripheral length, as with the Litz wire, and the VCO of the striped inductor simultaneously exhibits a lower phase noise than that of the conventional inductor. Striped and conventional inductors and VCOs are designed and fabricated, and their use of K- and Ka-bands is measured. Results show that the Q factor and corner frequency of the striped inductor are approximately 1.3 and 1.6 times higher, respectively, than that of the conventional inductor. Moreover, the 1-MHz-offset phase noise of the striped inductor's VCO in the K- and Ka-bands was approximately 3.5 dB lower than that of the conventional inductor. In this study, a 65-nm standard CMOS process was used.

Synthetic aperture radar (SAR) imagery is significantly deteriorated by the random phase noises which are generated by the frequency jitter of the transmit signal and atmospheric turbulence. In this paper, we recast the SAR imaging problem via the phase-corrupted data as for a special case of quadratic compressed sensing (QCS). Although the quadratic measurement model has potential to mitigate the effects of the phase noises, it also leads to a nonconvex and quartic optimization problem. In order to overcome these challenges and increase reconstruction robustness to the phase noises, we proposed a QCS-based SAR imaging algorithm by greedy local search to exploit the spatial sparsity of scatterers. Our proposed imaging algorithm can not only avoid the process of precise random phase noise estimation but also acquire a sparse representation of the SAR target with high accuracy from the phase-corrupted data. Experiments are conducted by the synthetic scene and the moving and stationary target recognition Sandia laboratories implementation of cylinders (MSTAR SLICY) target. Simulation results are provided to demonstrate the effectiveness and robustness of our proposed SAR imaging algorithm.

This paper proposes the proportional static-phase-error reduction (SPER) for the frequency-multiplier-based delay-locked-loop (DLL) architecture. The frequency multiplier (FM) can synthesize a combined clock to solve the high operational frequency of DLL. However, FM is sensitive to the static phase error of DLL. A SPER loop adopts a timing amplifier and a coarse-fine tuning technique to enhance the deterministic jitter of FM. The SPER loop proportionally reduces the static phase error and can extend the operating range of FM.

A low-voltage controller-based all-digital phase-locked loop (ADPLL) utilized in the medical implant communication service (MICS) frequency band was designed in this study. In the proposed design, controller-based loop topology is used to control the phase and frequency to ensure the reliable handling of the ADPLL output signal. A digitally-controlled oscillator with a delta-sigma modulator was employed to achieve high frequency resolution. The phase error was reduced by a phase selector with a 64-phase signal from the phase interpolator. Fabricated using a 130-nm CMOS process, the ADPLL has an active area of 0.64 mm2, consumes 840 µW from a 0.7-V supply voltage, and has a settling time of 80 µs. The phase noise was measured to be -114 dBc/Hz at an offset frequency of 200 kHz.

An on-chip monitoring circuit using a sub-sampling scheme, which consists of a 6-bit flash analog-to-digital converter (ADC) and a 51-phase phase-locked loop (PLL)-based frequency synthesizer, is proposed to analyze the signal integrity of a single-ended 8-Gb/s octal data rate (ODR) chip-to-chip interface with a source synchronous clocking scheme.

We propose an impact and high-pitch noise-suppression method based on spectral entropy. Spectral entropy takes a large value for flat spectral amplitude and a small value for spectra with several lines. We model the impact noise as a flat spectral signal and its damped oscillation as a high-pitch periodic signal consisting of spectra with several lines. We discriminate between the current noise situations by using spectral entropy and adaptively change the noise-suppression parameters used in a zero phase-based impact-noise-suppression method. Simulation results show that the proposed method can improve the perceptual evaluation of the speech quality and speech-recognition rate compared to conventional methods.

This paper presents a varactor-based all-digital phase-locked loop (ADPLL) with a multi-phase digitally controlled oscillator (DCO) for near-threshold voltage operation. In addition, a new all-digital reference spur suppression (RSS) circuit with multiple phases random-sampling techniques to effectively spread the reference clock frequency is proposed to randomize the synchronized DCO register behavior and reduce the reference spur. Because the equivalent reference clock frequency is reserved, the loop behavior is maintained. The area of the proposed spur suppression circuit is only 4.9% of the ADPLL (0.038 mm2). To work reliably at the near-threshold region, a multi-phase DCO with NMOS varactors is presented to acquire precise frequency resolution and high linearity. In the near-threshold region (VDD =0.52 V), the ADPLL only dissipates 269.9 μW at 100 MHz output frequency. It has a reference spur of -52.2 dBc at 100 MHz output clock frequency when the spur suppression circuit is deactivated. When the spur suppression circuit is activated, the ADPLL shows a reference spur of -57.3 dBc with the period jitter of 0.217% UI.

Ranging is commonly used to measure the distance to a satellite, since it is one of the quickest and most effective methods of finding the position of a satellite. In general, ranging ambiguity is easily resolved using major and subsequent ambiguity-resolving tones. However, an induced unknown phase error could interfere with resolving the ranging ambiguity. This paper suggests an effective and practical method to resolve the ranging ambiguity without changing the original planned ranging tone frequencies when an unknown non-linear phase error exists. Specifically, the present study derives simple equations for finding the phase error from the physical relationship between the measured major and minor tones. Furthermore, a technique to select the optimal ambiguity integer and correct phase error is provided. A numerical analysis is performed using real measurements from a low earth orbit (LEO) satellite to show its suitability and effectiveness. It can be seen that a non-ambiguous range is acquired after compensating the unknown phase error.

This paper describes a fast and effective algorithm for refining the parameter estimates of multicomponent third-order polynomial phase signals (PPSs). The efficiency of the proposed algorithm is accompanied by lower signal-to-noise ratio (SNR) threshold, and computational complexity. A two-step procedure is used to estimate the parameters of multicomponent third-order PPSs. In the first step, an initial estimate for the phase parameters can be obtained by using fast Fourier transformation (FFT), k-means algorithm and three time positions. In the second step, these initial estimates are refined by a simple moving average filter and singular value decomposition (SVD). The SNR threshold of the proposed algorithm is lower than those of the non-linear least square (NLS) method and the estimation refinement method even though it uses a simple moving average filter. In addition, the proposed method is characterized by significantly lower complexity than computationally intensive NLS methods. Simulations confirm the effectiveness of the proposed method.

In this paper, we derive two simple asymptotic closed-form formulas for the average bit error probability (BEP) of differential quaternary phase shift keying (DQPSK) with Gray encoding and a simple asymptotic approximation for the average symbol error probability (SEP) of doubly-differential quaternary phase shift keying (DDQPSK) in Nakagami-m fading channels. Compared with the existing BEP/SEP expressions, the derived concise formulas are much more effective in evaluating the asymptotic properties of DQPSK/DDQPSK with various Nakagami fading parameters, the accuracy of which is verified by extensive numerical results.

In this paper, we present a modified image rejection method that uses imbalance compensation techniques for phase and gain in low-intermediate frequency (IF) software-defined radio (SDR) receivers. In low-IF receivers, the image frequency signal interferes with the desired signal owing to the phase and gain imbalances caused by analog devices. Thus, it is difficult to achieve the required image rejection ratio (IRR) of over 60dB without compensation. To solve this problem, we present modified blind compensation techniques based on digital signal processing using a feedback control loop with a practical computation process. The modified method can reduce the complexity when a hardware logic circuit is used, like an FPGA. The simulation and experimental results verify that the modified method achieves an IRR greater than 50-60dB for both the carrier and the modulated waves.

This paper proposes a method of watermarking for digital audio signals based on adaptive phase modulation. Audio signals are usually non-stationary, i.e., their own characteristics are time-variant. The features for watermarking are usually not selected by combining the principle of variability, which affects the performance of the whole watermarking system. The proposed method embeds a watermark into an audio signal by adaptively modulating its phase with the watermark using IIR all-pass filters. The frequency location of the pole-zero of an IIR all-pass filter that characterizes the transfer function of the filter is adapted on the basis of signal power distribution on sub-bands in a magnitude spectrum domain. The pole-zero locations are adapted so that the phase modulation produces slight distortion in watermarked signals to achieve the best sound quality. The experimental results show that the proposed method could embed inaudible watermarks into various kinds of audio signals and correctly detect watermarks without the aid of original signals. A reasonable trade-off between inaudibility and robustness could be obtained by balancing the phase modulation scheme. The proposed method can embed a watermark into audio signals up to 100 bits per second with 99% accuracy and 6 bits per second with 94.3% accuracy in the cases of no attack and attacks, respectively.

In all-optical switches using the cascade of second harmonic generation and difference frequency mixing in periodically poled lithium niobate (PPLN) waveguide devices, walk-off between the fundamental and second harmonic pulses causes crosstalk between neighboring symbols, and limits the switching performance. In this paper, we numerically study retiming characteristics of all-optical switches that employ the PPLN waveguide devices with consideration for the effects of the crosstalk and for the input timing of the data and clock pulses. We find that the time offset between the data and clock pulses can control the timing jitter of the switched output; an appropriate offset can reduce the jitter while improving the switching efficiency.

To develop a flexible liquid crystal display (LCD) with a wide viewing angle range and high contrast ratio, we have proposed a flexible blue-phase LC device sustained by polymer walls inside the LC cell. We clarified that the polymer walls can maintain a constant cell gap and suppress the generation of alignment defects of the blue-phase LC in a bending state.

A low-complexity time-frequency multiplex estimator and low-complexity equalizer transceiver design are proposed to combat the problems of RF impairment associated with zero-IF transceiver of multi-carrier systems. Moreover, the proposed preambles can estimate the transmitter (TX) in-phase and quadrature-phase (IQ) imbalance, carrier frequency offset (CFO), and channel impulse response parameters. The proposed system has two parts. First, all parameters of the impairments are estimated by the designed time-frequency multiplex estimator. Second, the estimated parameters are used to compensate the above problems and detect the transmitted signal with low complexity. Simulation results confirm that the proposed estimator performs reliably with respect to IQ imbalance, CFO, and multipath fading channel effects.

High gain extinction ratio and stable control of the phase in phase sensitive amplification are fundamental to realize either phase regeneration or quadrature squeezing of phase modulated signals in an efficient and robust manner. In this paper, we show that a combination of our previously demonstrated “sideband-assisted” dual-pump phase sensitive amplifier with a gain extinction ratio of more than 25dB, and a phase-locked loop based stabilization technique, enable efficient QPSK quadrature squeezing. Its stable operation is exploited to realize phase de-multiplexing of QPSK signals into BPSK tributaries. The phase de-multiplexed signals are evaluated through measurement of constellation diagrams, eye diagrams and more importantly, BER curves. The de-multiplexed BPSK signals exhibited an OSNR penalty of less than 1dB compared to the back-to-back BPSK signals.

Methods of window matching to estimate 3D points are the most serious factors affecting the accuracy, robustness, and computational cost of Multi-View Stereo (MVS) algorithms. Most existing MVS algorithms employ window matching based on Normalized Cross-Correlation (NCC) to estimate the depth of a 3D point. NCC-based window matching estimates the displacement between matching windows with sub-pixel accuracy by linear/cubic interpolation, which does not represent accurate sub-pixel values of matching windows. This paper proposes a technique of window matching that is very accurate using Phase-Only Correlation (POC) with geometric correction for MVS. The accurate sub-pixel displacement between two matching windows can be estimated by fitting the analytical correlation peak model of the POC function. The proposed method also corrects the geometric transformations of matching windows by taking into consideration the 3D shape of a target object. The use of the proposed geometric correction approach makes it possible to achieve accurate 3D reconstruction from multi-view images even for images with large transformations. The proposed method demonstrates more accurate 3D reconstruction from multi-view images than the conventional methods in a set of experiments.

Neural networks are widely used in various fields due to their superior learning abilities. This paper proposes a hardware winner-take-all neural network (WTANN) that employs a new winner-take-all (WTA) circuit with phase-modulated pulse signals and digital phase-locked loops (DPLLs). The system uses DPLL as a computing element, so all input values are expressed by phases of rectangular signals. The proposed WTA circuit employs a simple winner search circuit. The proposed WTANN architecture is described by very high speed integrated circuit (VHSIC) hardware description language (VHDL), and its feasibility was tested and verified through simulations and experiments. Conventional WTA takes a global winner search approach, in which vector distances are collected from all neurons and compared. In contrast, the WTA in the proposed system is carried out locally by a distributed winner search circuit among neurons. Therefore, no global communication channels with a wide bandwidth between the winner search module and each neuron are required. Furthermore, the proposed WTANN can easily extend the system scale, merely by increasing the number of neurons. The circuit size and speed were then evaluated by applying the VHDL description to a logic synthesis tool and experiments using a field programmable gate array (FPGA). Vector classifications with WTANN using two kinds of data sets, Iris and Wine, were carried out in VHDL simulations. The results revealed that the proposed WTANN achieved valid learning.

This paper presents a cell-based all-digital phase-locked loop (ADPLL) with hierarchical gated digitally controlled oscillator (G-DCO) for low voltage operation, wide frequency range as well as low-power consumption. In addition, a new time-domain hierarchical frequency estimation algorithm (HFEA) for frequency acquisition is proposed to estimate the output frequency in 1.5MF (MF = 3 in this paper) cycles and this fast lock-in time is suitable to the dynamic voltage frequency scaling (DVFS) systems. A hierarchical G-DCO is proposed to work at low supply voltage to reduce the power consumption and at the same time to achieve wide frequency range and precise frequency resolution. The core area of the proposed ADPLL is 0.02635 mm2. In near-threshold region (VDD = 0.36 V), the proposed ADPLL only dissipates 68.2 µW and has a rms period jitter of 1.25% UI at 60 MHz output clock frequency. Under 0.5 V VDD operation, the proposed ADPLL dissipates 404.2 µW at 400 MHz. The fast lock-in time of 4.489 µs and the low jitter performance below 0.5% UI at 400 MHz output clock frequency in the proposed ADPLL are suitable in event-driven or DVFS applications.

We investigate a quantization error improvement technique using a dual rail configuration for optical quantization. Our proposed optical quantization uses intensity-to-wavelength conversion based on soliton self-frequency shift and spectral compression based on self-phase modulation. However, some unfavorable input peak power regions exist due to stagnations of wavelength shift or distortions of spectral compression. These phenomena could induce a serious quantization error and degrade the effective number of bit (ENOB). In this work, we propose a quantization error improvement technique which can make up for the unfavorable input peak power regions. We experimentally verify the quantization error improvement effect by the proposed technique in 6 bit optical quantization. The estimated ENOB is improved from 5.35 bit to 5.66 bit. In addition, we examine the XPM influence between counter-propagating pulses at high sampling rate. Experimental results and numerical simulation show that the XPM influence is negligible under ∼40 GS/s conditions.