Transmitter diversity is a powerful technique to improve the transmission quality of downlink in microcellular mobile communications systems. Under cochannel interference (CCI) at the base station (BS), the transmitter diversity is not necessarily effective, because the desired-plus-interference signal power used as a criterion of downlink branch selection is not always relative to the downlink propagation condition. This paper proposes the theoretical derivation of bit error rate (BER) performance in the transmitter diversity under CCI occurring at BS, as parameters of average SIR at BS, normalized Doppler frequency, and so on. It is confirmed from the correspondence of theoretical results with simulation results that the proposed theoretical approach is applicable to the CCI environments at BS.

In this paper, we propose an efficient channel estimation technique for orthogonal frequency-division multiplexing (OFDM) systems with transmitter diversity. The proposed technique estimates uniquely all channel frequency responses needed in space-time coded OFDM systems using "comb-type" training symbols. The computational complexity of the proposed technique is reduced dramatically, compared with the previous minimum mean-squared error (MMSE) technique, due to the processing made all in the frequency-domain. Also, several other techniques for mitigating random noise effect and tracking channel variation are discussed to further improve the performance of the proposed approach. The performances of the proposed approach are demonstrated by computer simulation for mobile wireless channels.

12-channel DC to 622-Mbit/s/ch optical transmitter and receiver have been developed for high-capacity and rather long (about 100 m) bit-parallel raw data transmission in intra- and inter-cabinet interconnection of large-scale switching, routing and computing system. Bit-parallel raw data transmission is done by using a bit-by-bit operational automatic decision threshold control receiver circuit with a DC-coupled configuration, the pin-PDs with their anodes and cathodes separated in a channel-by-channel manner, and a receiver preamplifier with a low-pass filter. The transmitter consists of a 12-channel LD sub-assembly unit and a LD driver LSI. The LD sub-assembly unit consists of a 12-channel array of high temperature characteristic 1.3-µm planar buried hetero-structure (PBH) LDs and 62.5/125 graded-index multi-mode fibers (GI62.5 MMFs). The 1.3-µm PBH LDs and the GI62.5 MMFs are optically coupled by passively visual alignment technology on the Si V-groove. The receiver consists of a 12-channel pin-PD sub-assembly unit and a receiver LSI. The pin-PD sub-assembly unit consist of a 12-channel array of pin-PDs and GI62.5 MMFs. They are optically coupled by using a flip-chip bonding on the Si V-groove. The transmitter and receiver each have eleven data channels and one clock channel. The size is as small as 3.6 cc for each modules, and the power consumptions are 1.7 W (transmitter) and 1.35 W (receiver). They transmitted a bit-parallel raw data through a 100-meter ribbon of GI62.5 MMFs in an ambient temperature range of 0-70C. They provide a synchronous PECL interface parallel link for with a 3.3-V single power supply.

The paper proposes a transmitter diversity scheme with a desired signal selection for the mobile communication systems in which the severe cochannel interference (CCI) is assumed to occur at the base station. The feature of the proposed scheme is that the criterion of the downlink branch selection is based on the desired signal power estimated by the correlation between the received signal and the unique word at the matched filter. Moreover, the unique word length control method according to the instantaneous SIR is applied to the proposed scheme, taking account of the uplink transmission efficiency. Computer simulation results show that the proposed scheme provides the better performance than the conventional transmitter diversity in the severe CCI environments, and that the unique word length control method applied to the proposed scheme decreases the unique word length without the degradation of the transmission quality, comparing with the fixed unique word length method.

This paper describes a 270-MHz CMOS quadrature modulator (QMOD) for a global system for mobile communications (GSM) transmitter. QMOD consists of two attenuators and two doubly-balanced modulators (DBM's) and fabricated by using 0.35-µm CMOS process. The carrier leakage level of -35.7 dBc and the image rejection level of -45.1 dBc are achieved. It's total chip area is 880 µm550 µm and it consumes 1.0 mA with 3.0 V power supply.

This paper describes a 2.5-Gb/s optical receiver and transmitter chipset consisting of a preamplifier, a main amplifier, a clock and data recovery (CDR) circuit, and a laser-diode (LD) driver. Low-voltage and adjustment-free circuit techniques are introduced in order to achieve low cost and low power circuits. Circuit adjustments are eliminated by using a multi-stage automatic offset canceling technique in the main amplifier, and by using a PLL structure with a sample-and-hold technique in the CDR circuit. For power reduction, ICs are operated at a power supply voltage of -3 V. Fabricating the ICs by a 0.5-µm Si bipolar process makes it possible to achieve 2.5-Gb/s receiver and transmitter operation with a total power dissipation of 1.04 W. Especially significant is that the receiver ICs need no external devices and adjustments.

A direct conversion transmitter IC including a proposed frequency doubler, a quadrature modulator, and a 3-bit variable attenuator was fabricated using BiCMOS technology with fT of 12 GHz. This architecture employing frequency doubler is intended for realizing wireless terminals that are low in cost and small in size. The architecture is effective for reducing serious interference between PA and VCO by making the VCO frequency different from that of PA. The proposed frequency doubler comprises a current-driven 90 phase-shifter and an ECL-EXOR circuit for both low power operation and wide input power range of local oscillator (LO). The proposed frequency doubler keeps high output power even when rectangular wave from LO is applied owing to use of the current-driven 90 phase-shifter instead of a voltage-driven 90 phase-shifter. An LO leakage of less than -25 dBc, an image rejection ratio in excess of 45 dBc, and a maximum attenuation of 21 dB were measured. The transmitter IC successfully operates at LO power above -15 dBm and consumes 68 mA from 2.7 V power supply voltage. An active die size is 1.5 mm3 mm.

This paper describes a CMOS Offset Phase Locked Loop (OPLL) for a global system for mobile communications (GSM) transmitter. The OPLL is a PLL with a down-conversion mixer in the feedback path and is used in the transmit (Tx) path as a frequency converter. It has a tracking bandpass filter characteristic in such a way that the OPLL can suppress the noise in the GSM receiving band (Tx noise) without a duplexer. When the loop bandwidth of the OPLL was 1.0 MHz, the Tx noise level of -163.5 dBc/Hz, the phase error of 0.66rms, and the settling time of 40µs were achieved. The IC was implemented by using 0.35-µm CMOS process. It takes 860µm620µm of total chip area and consumes 17.6 mA with a 3.0 V power supply.

This paper compares the BER performance of two types of pilot channel-based coherent Rake combining achievable by the use of weighted multi-slot averaging (WMSA) channel estimation filter in DS-CDMA transmission links. One is for the time-multiplexed pilot channel and the other is for the parallel pilot channel. The WMSA channel estimation filter weights and averages the received pilot over a period of several slots to improve the BER performance. We propose the WMSA channel estimation filters for time-multiplexed pilot and parallel pilot structures. Achievable BER performance under frequency-selective fading environments is computer simulated. The simulation results show that almost same BER performance can be achieved for both pilot channel structures when the same energy is allocated to the pilot.

We previously proposed a next generation cellular system for IMT-2000 based on wideband DS-CDMA with TDD scheme and have evaluated its performance by computer simulation, laboratory and field experiments. This paper presents the design concept of TDD-mode operation on wideband DS-CDMA systems. These systems employ almost the same techniques with a little difference as FDD-mode. We also present the schemes of the TDD-mode specific techniques such as fast cell search, transmission diversity and transmitter power control and show the evaluation results of them are effective. Performance can be improved by use of enhanced techniques such as interference cancellation and adaptive antenna array diversity.

This paper proposes a low distortion technique which reduces transmitter intermodulation. It is shown that one of the third order transmitter intermodulation products generated can be reduced by using a parallel amplifier configuration which includes a 45 divider and a 45 combiner. It is already known that the other third order transmitter intermodulation product can be reduced by using a parallel amplifier configuration using 90 hybrids. Thus, all of the third order transmitter intermodulation can be reduced by combining these configurations. This paper also shows the experimental results obtained with a parallel amplifier using 90 hybrids and one using a 45 divider and combiner in the K-band. The spectra of these amplifiers are compared, and it is found that third order transmitter intermodulation can be reduced by more than 29 dB in the parallel amplifier using the 45 divider and combiner.

This paper reviews Dynamic Channel Allocation (DCA) in TDMA cellular systems. The emphasis is on distributed DCA, which features decentralized control and adaptability to interference. Performance measures are discussed not only from a theoretical viewpoint but also from a practical viewpoint. Major techniques to enhance the capacity of cellular systems are channel segregation, reuse-partitioning, and transmitter power control. In addition to the performance of conventional cellular systems, differing performance in microcellular systems and multi-layer cellular systems is also discussed.

A 1.5 GHz band Si power MOS amplifier module with 50% total efficiency, 1 W output power and 30 dB power gain has been developed for front-end transmitter of digital cellular telephones. A combination of a highly efficient power MOSFET for the output stage and an integrated two stage MOS amplifier for the driver with an impedance matching circuit minimizing the length of striplines made it possible to achieve high total efficiency, high power gain, and smaller size of the amplifier module.

We compared--for the same propagation conditions and parameters--the performances of distributed dynamic channel assignment (DDCA) strategies and the performance of fixed channel assignment (FCA). This comparison quantitatively showed the effects of DDCA strategies in increasing spectrum efficiency. It also showed that using DDCA with transmitter power control (TPC) increases the system capacity to 3 4 times what it is with FCA and to 1.4 1.8 times what it is when using DDCA without TPC. We also evaluated the blocking rate and the interference probability for the inside of a cell and found that these are generally much higher close to the cell border than they are near the base station.

This paper describes the effective countermeasures for exfoliation of large-sized ceramic capacitors, deterioration of dummy resistors and developement of a spark sensor with UVtrons at 300-500 kW transmitting stations. Cracks and exfoliation were found at the electrode of large-sized ceramic capacitors in the output circuit of the 500 kW transmitter. The exfoliation was caused by the temperature rise and the thermal fatigues at the electrode with the Nickel plating including Irons. A pure Nickel-plated electrode including no Irons and a new soldering method using disk-typed solder with a large adhesive area are employed in order to reduce the temperature rise. The temperature rise of the improved capacitor was 18 lower than the conventional one. Deterioration of ELEMA resistors of the 300 kW dummy antenna was discovered. The damage of the resistor was caused by the concentration of the electric current followed by the thermal stress cycle which made mechanical exhaustion at the electrode. Therefore, oval-shaped type resistors with much longer electric current path (20% up) to suppress the concentration of current flow and much slower temperature rise are newly developed. In case that sparks occurred at DC or RF high voltage impressed sections of the high power transmitting equipment, the discharged points could be seriously damaged by the transmitter energy itself. In orded to prevent this, a spark detector using UV (Ultra violet) trons is developed and installed at the matchign circuit of the 500 kW transmitter. Conventional UV sensors with only one UVtron could not detect feeble discharges and sparks with a duration time of less than 150 ms because of false outputs by the back ground noise. Since choosing three out of four UV trons system is employed, possibility producing a false output will be just one to 445 years theoretically. This means extremely reliable and sensitive spark detection system are constructed. These countermeasures have improved reliability of the transmitting equipment greatly. No damages have been found in the transmitters ever since.

Four imperfections encountered in transmitter power control (TPC) for direct sequence code division multiple access (DS/CDMA) cellular mobile communications systems, faulty TPC, finite dynamic range, restricted site diversity, and non-uniform user distribution, are investigated where account is taken of the effect of the propagation constant on the traffic capacity. Computer simulation schemes for traffic capacity estimation under these TPC imperfections are presented. Traffic capacity estimates are produced for a representative DS/CDMA cellular mobile communications system.