This report describes an all-digital phase-locked loop (ADPLL) using a temperature compensated settling time reduction technique. The novelty of this work is autonomous oscillation control word estimation without a look-up table or memory circuits. The proposed ADPLL employs a multi-phase digitally controlled oscillator (DCO). In the proposed estimation method, the optimum oscillator tuning word (OTW) is estimated from the DCO frequency characteristic in the setup phase of ADPLL. The proposed ADPLL, which occupies 0.27×0.36mm2, is fabricated by a 65 nm CMOS process. The temperature compensation PLL controller (TCPC) is implemented using an FPGA. Although the proposed method has 20% area overhead, measurement results show that the 47% settling time is reduced. The average settling time at 25°C is 3µs. The average reduction energy is at least 42% from 0°C to 100°C.

We present a time-to-digital converter (TDC) achieving sub-picosecond resolution and high precision for all-digital phase-locked-loops (ADPLLs). The basic idea is using a charge pump to translate time interval into charge, and a successive-approximation-register-analog-to-digital converter (SAR-ADC) to quantize the charge. With this less complex configuration, high resolution, high precision, low power, and small area can be achieved all together. We analyzed the noise contribution from the charge pump and describe detailed design and implementation for sizing the capacitor and transistors, with the awareness of noise and linearity. The analysis demonstrates the proposed TDC capable of sub-picosecond resolution and high precision. Two prototype chips were fabricated in 65nm CMOS with 0.06mm2, and 0.018mm2 core areas, respectively. The achieved resolutions are 0.84ps and 0.80ps, in 8-bit and 10-bit range, respectively. The measured single-shot-precisions range from 0.22 to 0.6ps, and from 0.66 to 1.04ps, respectively, showing consistent trends with the analysis. Compared with state-of-the-arts, best performance balance has been achieved.

This paper proposes a high frequency resolution Digitally-Controlled Oscillator (DCO) using a single-period control bit switching scheme. The proposed scheme controls the tuning word of DCO in a single period for the fine frequency tuning. The LC type DCO is implemented to realize the proposed scheme, and is fabricated using a standard 65 nm CMOS technology. The measurement results show that the implemented DCO improves the frequency resolution from 560 kHz to 180 kHz without phase noise degradation with an additional area of 200 µm2.

This paper presents an ADPLL using a hierarchical TDC composed of a 4fLO DCO followed by a divide-by-4 circuit and three stages of known phase interpolators. We derived simple design requirements for ensuring precision of the phase interpolator. The proposed architecture provides immunity to PVT and local variations, which allows calibration-free operation, as well as sub-inverter delay resolution contributing to good in-band phase noise performance. Also the hierarchical TDC makes it possible to employ a selective activation scheme for power saving. Measured performances demonstrate the above advantages and the in-band phase noise reaches -104 dBc/Hz. It is fabricated in a 65 nm CMOS process and the active area is 0.18 mm2.

In this paper, we propose a two-step TDC with phase-interpolator and time amplifier to satisfy high resolution at 2.4 GHz input frequency by implementing delay time less than that of an inverter delay. The accuracy of phase-interpolator is improved for process variation using the resistor automatic-tuning circuit. The gain of time amplifier is improved using the delay time difference between two delay cells. It is implemented in a 0.13 µm CMOS process with a die area of 0.68 mm2. And the power consumption is 14.4 mW at a 1.2 V supply voltage. The resolution and input frequency of the TDC are 0.357 ps and 2.4 GHz, respectively.

This paper describes an ADPLL (All Digital Phase-Locked Loops) with a small DCO (Digitally Controlled Oscillator), low jitter, fine resolution and wide lock range suitable for mobile appplications. The novel DCO circuit is controlled by digital control codes with thermometer type instead of previous binary weighted type. Therefore, the DCO has small area and it has significantly small jitter when the control input is updated. The hierarchical DCO type with two loops makes it possible to have fine resolution and wide lock range. Functional verification and noise analysis of the ADPLL is performed by MATLAB simulink to improve design TAT (Turn-Around Time). And The ADPLL chip is in fabrication using a SEC 0.18 µm CMOS technology. The ADPLL has lock range between 520 MHz and 1.5 GHz and has peak-to-peak jitter 70 ps at 670 MHz.