Aiming at the problem of the deterioration of the contact performance caused by the wear debris generated during the fretting wear of the electrical connector, low-frequency fretting wear experiments were carried out on the contacts of electrical connectors, the accumulation and distribution of the wear debris were detected by the electrical capacitance tomography technology; the influence of fretting cycles, vibration direction, vibration frequency and vibration amplitude on the accumulation and distribution of wear debris were analyzed; the correlation between characteristic value of wear debris and contact resistance value was studied, and a performance degradation model based on the accumulation and distribution of wear debris was built. The results show that fretting wear and performance degradation are the most serious in axial vibration; the characteristic value of wear debris and contact resistance are positively correlated with the fretting cycles, vibration frequency and vibration amplitude; there is a strong correlation between the sum of characteristic value of wear debris and the contact resistance value; the prediction error of ABC-SVR model of fretting wear performance degradation of electrical connectors constructed by the characteristic value of wear debris is less than 6%. Therefore, the characteristic value of wear debris in contact subareas can quantitatively describe the degree of fretting wear and the process of performance degradation.

Soil moisture sensor calibration based on the Multivariate Adaptive Regression Splines (MARSplines) model is studied in this paper. Different from the generic polynomial fitting methods, the MARSplines model is a non-parametric model, and it is able to model the complex relationship between the actual and measured soil moisture. Rao-1 algorithm is employed to tune the hyper-parameters of the calibration model and thus the performance of the proposed method is further improved. Data collected from four commercial soil moisture sensors is utilized to verify the effectiveness of the proposed method. To assess the calibration performance, the proposed model is compared with the model without using the temperature information. The numeric studies prove that it is promising to apply the proposed model for real applications.

Broadcast services for wireless local area networks (WLANs) are being standardized in the IEEE 802.11 task group bc. Envisaging the upcoming coexistence of broadcast access points (APs) with densely-deployed legacy APs, this paper addresses a learning-based spatial reuse with only partial receiver-awareness. This partial awareness means that the broadcast APs can leverage few acknowledgment frames (ACKs) from recipient stations (STAs). This is in view of the specific concerns of broadcast communications. In broadcast communications for a very large number of STAs, ACK implosions occur unless some STAs are stopped from responding with ACKs. Given this, the main contribution of this paper is to demonstrate the feasibility to improve the robustness of learning-based spatial reuse to hidden interferers only with the partial receiver-awareness while discarding any re-training of broadcast APs. The core idea is to leverage robust adversarial reinforcement learning (RARL), where before a hidden interferer is installed, a broadcast AP learns a rate adaptation policy in a competition with a proxy interferer that provides jamming signals intelligently. Therein, the recipient STAs experience interference and the partial STAs provide a feedback overestimating the effect of interference, allowing the broadcast AP to select a data rate to avoid frame losses in a broad range of recipient STAs. Simulations demonstrate the suppression of the throughput degradation under a sudden installation of a hidden interferer, indicating the feasibility of acquiring robustness to the hidden interferer.

Lifelong language learning (LLL) aims at learning new tasks and retaining old tasks in the field of NLP. LAMOL is a recent LLL framework following data-free constraints. Previous works have been researched based on LAMOL with additional computing with more time costs or new parameters. However, they still have a gap between multi-task learning (MTL), which is regarded as the upper bound of LLL. In this paper, we propose Metacognitive Adaptation (Metac-Adapt) almost without adding additional time cost and computational resources to make the model generate better pseudo samples and then replay them. Experimental results demonstrate that Metac-Adapt is on par with MTL or better.

To improve the performance of underwater acoustic communications, this letter proposes a polar coding scheme with adaptive channel equalization, which can reduce the amount of feedback information. Furthermore, a hybrid automatic repeat request (HARQ) mechanism is provided to mitigate the impact of estimation errors. Simulation results show that the proposed scheme outperforms the turbo equalization in bit error rate. Computational complexity analysis is also provided for comparison.

A method of radar-based contactless vital-sign sensing and electrocardiogram (ECG) signal reconstruction using deep learning is proposed. A radar system is an effective tool for contactless vital-sign sensing because it can measure a small displacement of the body surface without contact. However, most of the conventional methods have limited evaluation indices and measurement conditions. A method of measuring body-surface-displacement signals by using frequency-modulated continuous-wave (FMCW) radar and reconstructing ECG signals using a convolutional neural network (CNN) is proposed. This study conducted two experiments. First, we trained a model using the data obtained from six subjects breathing in a seated condition. Second, we added sine wave noise to the data and trained the model again. The proposed model is evaluated with a correlation coefficient between the reconstructed and actual ECG signal. The results of first experiment show that their ECG signals are successfully reconstructed by using the proposed method. That of second experiment show that the proposed method can reconstruct signal waveforms even in an environment with low signal-to-noise ratio (SNR).

Constructing accurate similarity graph is an important process in graph-based clustering. However, traditional methods have three drawbacks, such as the inaccuracy of the similarity graph, the vulnerability to noise and outliers, and the need for additional discretization process. In order to eliminate these limitations, an entropy regularized unsupervised clustering based on maximum correntropy criterion and adaptive neighbors (ERMCC) is proposed. 1) Combining information entropy and adaptive neighbors to solve the trivial similarity distributions. And we introduce l0-norm and spectral embedding to construct similarity graph with sparsity and strong segmentation ability. 2) Reducing the negative impact of non-Gaussian noise by reconstructing the error using correntropy. 3) The prediction label vector is directly obtained by calculating the sparse strongly connected components of the similarity graph Z, which avoids additional discretization process. Experiments are conducted on six typical datasets and the results showed the effectiveness of the method.

Distributed array radars consist of multiple sub-arrays separated by tens to hundreds of wavelengths and can match narrow beamwidths with large-aperture, high-gain antennas. The physical independence of the sub-arrays contributes to significant structure flexibility and is one of the advantages of such radars. However, a typical problem is the grating lobes in the digital beam forming (DBF) beam pattern. Unfortunately, the need to suppress the generation of grating lobes makes the design of acceptable sub-array arrangements very difficult. A sigma-delta beam former direction of arrival (DOA) estimation method is proposed in this study to solve this problem. The proposed method performs DOA estimation by acquiring the difference signals in addition to the sum signals of all sub-arrays. The difference signal is typically used for monopulse DOA estimation in the phased array radar. The sigma-delta beamformer simultaneously has both advantages of DOA estimations using a distributed array with a large aperture length and using a sub-array that is not affected by the grating lobe. The proposed method can improve the DOA estimation accuracy over the conventional method under grating lobe situations and help the distributed array radar achieve flexibility in the sub-array arrangement. Numerical simulations are presented to verify the effectiveness of the proposed DOA estimation method.

In this study, we propose an accurate range-Doppler analysis algorithm for moving multiple objects in a short range using microwave (including millimeter wave) radars. As a promising Doppler analysis for the above model, we previously proposed a weighted kernel density (WKD) estimator algorithm, which overcomes several disadvantages in coherent integration based methods, such as a trade-off between temporal and frequency resolutions. However, in handling multiple objects like human body, it is difficult to maintain the accuracy of the Doppler velocity estimation, because there are multiple responses from multiple parts of object, like human body, incurring inaccuracies in range or Doppler velocity estimation. To address this issue, we propose an iterative algorithm by exploiting an output of the WKD algorithm. Three-dimensional numerical analysis, assuming a human body model in motion, and experimental tests demonstrate that the proposed algorithm provides more accurate, high-resolution range-Doppler velocity profiles than the original WKD algorithm, without increasing computational complexity. Particularly, the simulation results show that the cumulative probabilities of range errors within 10mm, and Doppler velocity error within 0.1m/s are enhanced from 34% (by the former method) to 63% (by the proposed method).

In this paper, we propose a multi-domain learning model for action recognition. The proposed method inserts domain-specific adapters between layers of domain-independent layers of a backbone network. Unlike a multi-head network that switches classification heads only, our model switches not only the heads, but also the adapters for facilitating to learn feature representations universal to multiple domains. Unlike prior works, the proposed method is model-agnostic and doesn't assume model structures unlike prior works. Experimental results on three popular action recognition datasets (HMDB51, UCF101, and Kinetics-400) demonstrate that the proposed method is more effective than a multi-head architecture and more efficient than separately training models for each domain.

Recently, robust speech recognition for real-world applications has attracted much attention. This paper proposes a robust speech recognition method based on the teacher-student learning framework for domain adaptation. In particular, the student network will be trained based on a novel optimization criterion defined by the encoder outputs of both teacher and student networks rather than the final output posterior probabilities, which aims to make the noisy audio map to the same embedding space as clean audio, so that the student network is adaptive in the noise domain. Comparative experiments demonstrate that the proposed method obtained good robustness against noise.

To mitigate the interference caused by range sidelobes in multiple-input multiple-output (MIMO) radar, we propose a new method to construct Doppler resilient complementary waveforms from complete complementary code (CCC). By jointly designing the transmit pulse train and the receive pulse weights, the range sidelobes can vanish within a specified Doppler interval. In addition, the output signal-to-noise ratio (SNR) is maximized subject to the Doppler resilience constraint. Numerical results show that the designed waveforms have better Doppler resilience than the previous works.

In this paper, a passive multiple-input multiple-output (MIMO) radar system with widely separated antennas that estimates the positions and velocities of multiple moving targets by utilizing time delay (TD) and doppler shift (DS) measurements is proposed. Passive radar systems can detect targets by using multiple uncoordinated and un-synchronized illuminators and we assume that all the measurements including TD and DS have been known by a preprocessing method. In this study, the algorithm can be divided into three stages. First, based on location information within a certain range and utilizing the DBSCAN cluster algorithm we can obtain the initial position of each target. In the second stage according to the correlation between the TD measurements of each target in a specific receiver and the DSs, we can find the set of DS measurements for each target. Therefore, the initial speed estimated values can be obtained employing the least squares (LS) method. Finally, maximum likelihood (ML) estimation of a first-order Taylor expansion joint TD and DS is applied for a better solution. Extensive simulations show that the proposed algorithm has a good estimation performance and can achieve the Cramér-Rao lower bound (CRLB) under the condition of moderate measurement errors.

Adaptive multilooking is a critical processing step in multi-temporal interferometric synthetic aperture radar (InSAR) measurement, especially in small temporal baseline subsets. Various amplitude-based adaptive multilook approaches have been proposed for the improvement of interferometric processing. However, the phase signal, which is fundamental in interferometric systems, is typically ignored in these methods. To fully exploit the information in complex SAR images, a nonlocal adaptive multilooking is proposed based on complex covariance matrix in this work. The complex signal is here exploited for the similiarity measurement between two pixels. Given the complexity of objects in SAR images, structure feature detection is introduced to adaptively estimate covariance matrix. The effectiveness and reliability of the proposed approach are demonstrated with experiments both on simulated and real data.

LiDAR is a distance sensor that plays a key role in the realization of advanced driver assistance systems (ADAS). In this paper, we present a tutorial and review of automotive direct time of flight (dToF) LiDAR from the aspect of circuit systems. We discuss the breakthrough in ADAS LiDARs through comparison with the first-generation LiDAR systems, which were conventionally high-cost and had an immature performance. We define current high-performance and low-cost LiDARs as next-generation LiDAR systems, which have significantly improved the cost and performance by integrating the photodetector, the readout circuit, and the signal processing unit into a single SoC. This paper targets reader who is new to ADAS LiDARs and will cover the basic principles of LiDAR, also comparing with range methods other than dToF. In addition, we discuss the development of this area through the latest research examples such as the 2-chip approach, 2D SPAD array, and 3D integrated LiDARs.

Regional Short Message Communication (RSMC) service of BeiDou Navigation Satellite System (BDS) has been widely used in various fields. BDS-3 officially started to provide service in 2020, and the performance of RSMC service was greatly improved, which offers an opportunity for large-scale applications of RSMC in consumer electronic products. Due to the complex application scenarios, the low-cost and low-power of RSMC terminals, a better coding scheme is needed to improve performance. In this paper, we propose a new polar encoding scheme with low code rate and variable code length, which adopts Polarization Weight (PW) to generate the reliability sequence of Polar codes and use a Nested Rate Adaptation Sequence (NRAS) to realize rate adaption for the BDS-3 RSMC. The performance of encoding gain and decoding complexity is analyzed by simulation and experiments. The results validate the effective of this scheme. Compared with Turbo codes, the proposed polar codes scheme achieves about 0.5dB gain with about 50% decoding complexity when the information length including CRC is 128 and code rate is 1/2. The proposed polar codes scheme provides a good reference for further applications in BDS.

This letter focuses on the cross-corpus speech emotion recognition (SER) task, in which the training and testing speech signals in cross-corpus SER belong to different speech corpora. Existing algorithms are incapable of effectively extracting common sentiment information between different corpora to facilitate knowledge transfer. To address this challenging problem, a novel convolutional auto-encoder and adversarial domain adaptation (CAEADA) framework for cross-corpus SER is proposed. The framework first constructs a one-dimensional convolutional auto-encoder (1D-CAE) for feature processing, which can explore the correlation among adjacent one-dimensional statistic features and the feature representation can be enhanced by the architecture based on encoder-decoder-style. Subsequently the adversarial domain adaptation (ADA) module alleviates the feature distributions discrepancy between the source and target domains by confusing domain discriminator, and specifically employs maximum mean discrepancy (MMD) to better accomplish feature transformation. To evaluate the proposed CAEADA, extensive experiments were conducted on EmoDB, eNTERFACE, and CASIA speech corpora, and the results show that the proposed method outperformed other approaches.

Hierarchical ID-based authenticated key exchange (HID-AKE) is a cryptographic protocol to establish a common session key between parties with authentication based on their IDs with the hierarchical delegation of key generation functionality. All existing HID-AKE schemes are selective ID secure, and the only known standard model scheme relies on a non-standard assumption such as the q-type assumption. In this paper, we propose a generic construction of HID-AKE that is adaptive ID secure in the HID-eCK model (maximal-exposure-resilient security model) without random oracles. One of the concrete instantiations of our generic construction achieves the first adaptive ID secure HID-AKE scheme under the (standard) k-lin assumption in the standard model. Furthermore, it has the advantage that the computational complexity of pairing and exponentiation operations and the communication complexity do not depend on the depth of the hierarchy. Also, the other concrete instantiation achieves the first HID-AKE scheme based on lattices (i.e., post-quantum).

In a previous study, we proposed a new method based on copula theory to evaluate the detection performance of distributed-processing multistatic radar systems, in which the dependence of local decisions was modeled by a Gaussian copula with linear dependence and no tail dependence. However, we also noted that one main limitation of the study was the lack of investigations on the tail-dependence and nonlinear dependence among local detectors' inputs whose densities have long tails and are often used to model clutter and wanted signals in high-resolution radars. In this work, we attempt to overcome this shortcoming by extending the application of the proposed method to several types of multivariate copula-based dependence models to clarify the effects of tail-dependence and different dependence models on the system detection performance in detail. Our careful analysis provides two interesting and important clarifications: first, the detection performance degrades significantly with tail dependence; and second, this degradation mainly originates from the upper tail dependence, while the lower tail and nonlinear dependence unexpectedly improve the system performance.

This paper aims to design multiple-input multiple-output (MIMO) radar receiving weights and transmitting waveforms, in order to obtain better spatial filtering performance and enhance the robustness in the case of signal-dependent interference and jointly inaccurate estimated angles of target and interference. Generally, an alternate iterative optimization algorithm is proposed for the joint design problem. Specifically, the receiving weights are designed by the generalized eigenvalue decomposition of the matrix which contains the estimated information of the target and interference. As the cost function of the transmitting waveform design is fractional, the fractional optimization problem is first converted into a secondary optimization problem. Based on the proposed algorithm, a closed-form solution of the waveform is given using the alternating projection. At the analysis stage, in the presence of estimated errors under the environment of signal-dependent interference, a robust signal-to-interference and noise ratio (SINR) performance is obtained using a small amount of calculation with an iterative procedure. Numerical examples verify the effectiveness of the performances of the designed waveform in terms of the SINR, beampattern and pulse compression.