Shouhei KOUSAI Daisuke MIYASHITA Junji WADATSUMI Rui ITO Takahiro SEKIGUCHI Mototsugu HAMADA Kenichi OKADA
A wideband, low noise, and highly linear transmitter for multi-mode radio is presented. Envelope injection scheme with a CMOS amplifier is developed to obtain sufficient linearity for complex modulation schemes such as OFDM, and to achieve low noise for concurrent operation of more than one standard. Active matching technique with doubly terminated LPF topology is also presented to realize wide bandwidth, low power consumption, and to eliminate off-chip components without increasing die area. A multi-mode transmitter is implemented in a 0.13 µm CMOS technology with an active area of 1.13 mm2. Third-order intermodulation product is improved by 17 dB at -3 dBm output by the envelope injection scheme. The transmitter achieves EVM of less than -29.5 dB at -3 dBm output from 0.2 to 7.2 GHz while consuming only 69 mW. The transmitter is also tested with multiple standards of UMTS, 802.11b, WiMax, 802.11a, and 802.11n, and satisfies EVM, ACLR, and spectrum specifications.
Jianqing WANG Kenichiro MASAMI Qiong WANG
The objective of this study is to investigate the feasibility of an ultra wideband (UWB) impulse radio system for in-body to off-body wireless communication for biomedical applications. At first, a UWB antenna is designed in the UWB low band for implant use in the chest. Then the channel model is extracted and established based on the finite difference time domain (FDTD) simulation with an anatomical human body model. The established channel model consists of a small set of parameters for generating discrete time impulse responses. The generated model shows good agreement with the FDTD-calculated result in terms of key communication metrics. For effective communication over the multipath-affected channel, the pulse position modulation is employed and a 2-finger RAKE structure with a constant temporal delay is proposed in the receiver. The bit error rate performance has shown the validity of the system in the in-body to off-body chest channel.
Xin NIE Jianhua ZHANG Ping ZHANG
Relay, which promises to enhance the performance of future communication networks, is one of the most promising techniques for IMT-Advanced systems. In this paper, multiple-input multiple-output (MIMO) relay channels based on outdoor measurements are investigated. We focus on the link between the base station (BS) and the relay station (RS) as well as the link between the RS and the mobile station (MS). First of all, the channels were measured employing a real-time channel sounder in IMT-Advanced frequency band (2.35 GHz with 50 MHz bandwidth). Then, the parameters of multipath components (MPCs) are extracted utilizing space-alternating generalized expectation algorithm. MPC parameters of the two links are statistically analyzed and compared. The polarization and spatial statistics are gotten. The trends of power azimuth spectrum (PAS) and cross-polarization discrimination (XPD) with the separation between the RS and the MS are investigated. Based on the PAS, the propagation mechanisms of line-of-sight and non-line-of-sight scenarios are analyzed. Furthermore, an approximate closed-form expression of channel correlation is derived. The impacts of PAS and XPD on the channel correlation are studied. Finally, some guidelines for the antenna configurations of the BS, the RS and the MS are presented. The results reveal the different characteristics of relay channels and provide the basis for the practical deployment of relay systems.
Chin-Long WEY Shin-Yo LIN Hsu-Sheng WANG Hung-Lieh CHEN Chun-Ming HUANG
In UWB systems, data symbols are transmitted and received continuously. The Fast Fourier Transform (FFT) processor must be able to seamlessly process input/output data. This paper presents the design and implementation of a continuous data flow parallel memory-based FFT (CF-PMBFFT) processor without the use of input buffer for pre-loading the input data. The processor realizes a memory space of two N-words and multiple processing elements (PEs) to achieve the seamless data flow and meet the design requirement. The circuit has been fabricated in TSMC 0.18 µm 1P6M CMOS process with the supply voltage of 1.8 V. Measurement results of the test chip shows that the developed CF-PMBFFT processor takes a core area of 1.97 mm2 with a power consumption of 62.12 mW for a throughput rate of 528 MS/s.
Naohiko IWAKIRI Takehiko KOBAYASHI
A multiband system can flexibly create spectral holes to avoid interference between different systems. When two systems within the same frequency band coexist, the multiband system must immediately detect the signals from all users to remove unwanted interference. The complication of creating spectral holes is to obtain an occupied frequency band and an angle-of-arrival of interfering system. These parameters must be measured at the receiver of multiband system and then fed back to the transmitter. This paper presents a channel estimator with an interference detector that is developed to implement and test it's functionality in a multiband system. The proposed estimator can precisely detect the parameters before demodulation, and quickly feed back the interfering system parameters to transmitter. The effective design and the detection error rate were evaluated via verification tests in an anechoic chamber and computer simulations. The results of the proposed technique show an ability of interference detection as well as channel estimation.
Hironobu YAMAMOTO Masato KOIWAI Takehiko KOBAYASHI
This paper describes ultra wideband (UWB) radio propagation measurements and modeling for wireless body area network (WBAN) applications in different environments. Several propagation measurement campaigns and associated modelings were carried out in either a radio anechoic chamber or a specific room type; however, dependence of the radio propagation on surrounding environments was not studied. Multipaths (mainly reflected from floor, ceiling, and walls) highly depend on the environment. To address this problem, radio propagation around the human body was measured in a radio anechoic chamber and four different-sized rooms. Parameters in a conventional loss model derived from the measurements were found to significantly diverge and depend on room volume and line-of-sight (LOS)/non-LOS (NLOS) cases. A modified model considering the impact of room volume has been proposed for the LOS/NLOS cases. Different propagation mechanisms were discussed along with parameter derivation. Probability distributions for the UWB propagation losses were also examined.
Hangue PARK Jongwook ZEONG Wonsuk CHOI Jung Han CHOI
A Q-enhanced 8th order CMOS active bandpass filter is presented employing a novel two-stage self-calibration technique. The proposed active filter shows the better out-band attenuation performance than other reported CMOS active bandpass filters. The proposed calibration method enables the stable filtering operation affected by neither the input power variation nor the strong interference power. It is fabricated using 65 nm CMOS process. The measured 3 dB bandwidth is 54 MHz at 2.37 GHz. The insertion loss is 2.9 dB and the out-band attenuation is 27.5 dB at 15 MHz offset frequency. The performance of the filter remains unchanged for 5% supply voltage variations.
A cognitive radio will have to sense and discover the spectral environments where it would not cause primary radios to interfere. Because the primary radios have the right to use the frequency, the cognitive radios as the secondary radios must detect radio signals before use. However, the secondary radios also need identifying the primary and other secondary radios where the primary radios are vulnerable to interference. In this paper, a method of simultaneously identifying signals of primary and secondary radios is proposed. The proposed bandwidth differentiation assumes the primary and secondary radios use orthogonal frequency division multiplexing (OFDM), and the secondary radios use at the lower number of subcarriers than the primary radios. The false alarm and detection probabilities are analytically evaluated using the characteristic function method. Numerical evaluations are also conducted on the assumption the primary radio is digital terrestrial television broadcasting. Result showed the proposed method could achieve the false alarm probability of 0.1 and the detection probability of 0.9 where the primary and secondary radio powers were 2.5 dB and 3.6 dB higher than the noise power. In the evaluation, the reception signals were averaged over the successive 32 snapshots, and the both the primary and secondary radios used QPSK. The power ratios were 4.7 dB and 8.4 dB where both the primary and secondary radios used 64QAM.
Kianoush SOURI Hossein SHAMSI Mehrshad KAZEMI Kamran SOURI
This paper presents a voltage reference that utilizes the virtually diode-connected MOS transistors, biased in the weak-inversion region. The proposed architecture increases the gain of the feedback loop that consequently reduces the system sensitivity, and hence improves the PSRR. The circuit is designed and simulated in a standard 0.18 µm CMOS technology. The simulation results in HSPICE indicate the successful operation of the circuit as follows: the PSRR at DC frequency is 86 dB and for the temperature range from -55C to 125C, the variation of the output reference voltage is less than 66 ppm/C.
Sinhyung JEON Hyengcheul CHOI Hyeongdong KIM
A planar inverted-E (PIE) antenna that can achieve a wide impedance bandwidth is proposed. The antenna is realized by inserting a branch capacitance between the feed line and the shorting pin of a conventional planar inverted-F antenna (PIFA). Such a modification significantly enhanced the impedance bandwidth while maintaining the antenna size. The proposed antenna possesses a very wide impedance bandwidth of 1250 MHz (1650-2900 MHz) at a voltage standing wave ratio (VSWR) <3. In addition, good radiation patterns were obtained at the desired frequency bands.
A stacked rectangular microstrip antenna with a shorting plate and a helical pin is proposed as a car antenna for triple band operation in ITS. The proposed antenna operates as a conventional stacked microstrip antenna at the highest frequency band. At the middle and the lowest frequency bands, the antenna radiates at low elevation angles from the helical pin and the shorting plate. In this paper, as an example of triple band antennas in the ITS, an antenna is designed that supports PHS, VICS and ETC. The proposed antennas have the proper radiation pattern for each application and are small in size.
Hye-Kwang KIM Jung-Hoon KIM Eugene RHEE Sung-Il YANG
This paper presents a method of expanding the operating frequency band of a Reverberating TEM Cell (RTC) for electromagnetic compatibility (EMC) testing. To expand the operating frequency band of an RTC, this paper places a wire septum inside the cell instead of a solid septum. The maximum usable frequency (MUF) for TEM cell operation and the lowest usable frequency (LUF) for reverberating chamber operation with the wire septum are studied and compared with a conventional solid septum. The E field strengths inside the RTC are measured and evaluated. The measurement results show that the RTC with the wire septum have similar MUF to the RTC with a solid septum at TEM mode, but have much lower LUF at a reverberating mode, which proves that the operating frequency band of the RTC can be expanded by using the wire septum.
Yihong ZHOU Jiayin LI Haiyang WANG Haiyan JIN
In this letter, a novel wideband traveling wave power divider/combiner based on the finline with irises is presented and studied. Experiments on the four-way passive divider/combiner demonstrate a minimum overall insertion loss of 1.5 dB at 35.8 GHz, and the insertion loss across 32-38 GHz is less than 2.5 dB.
Johanna VARTIAINEN Janne LEHTOMAKI Harri SAARNISAARI Markku Juntti Kenta UMEBAYASHI
The localization algorithm based on the double-thresholding (LAD) method was originally proposed for detecting and localizing narrowband (NB) signals with respect to the search bandwidth. Its weakness is that the localized signal is often split into several parts, especially when the signal-to-noise ratio (SNR) is low. This may lead to the illusion of unoccupied frequencies in the middle of the signals. In this paper, an extension of the LAD method, namely the two-dimensional LAD (2-D LAD), is proposed to solve that problem. In addition to offering low computational complexity, the proposed method is able to operate at lower SNR values than the original 1-D LAD method.
Niwat THEPVILOJANAPONG Shin'ichi KONOMI Yoshito TOBE
Portable sensory devices such as sensors equipped mobile phones enable convenient sensing and monitoring of urban areas. Such devices, which are always carried by humans, are referred to as Human Probes. Instead of carrying out sensing activities independently, cooperation of Human Probes helps in realizing efficient urban sensing environments. In this paper, we propose an Architecture of Qualitative Urban Information Blending and Acquisition (Aquiba), in which the sensing activities are adjusted autonomously according to cooperation of Human Probes. Aquiba introduces a cooperative sensing approach which aims to maintain desired sensing resolution efficiently while minimizing overall energy consumption. To study the performance of Aquiba, we have conducted comprehensive simulations ranging from small- to large-scale scenarios along with applying three different movement patterns of human. The simulation results demonstrate that Aquiba is capable of providing high sensing resolution and reducing overall energy consumption.
Seongmin PYO Min-Jae LEE Young-Sik KIM
In this letter, a new design of a metamaterial-based microstrip antenna is presented using triangular slots embedded on the ground plane to enhance the impedance bandwidth. To improve the impedance bandwidth of the proposed antenna, two resonant mode frequencies are closely allocated using the slotted ground without changing the radiator element. The impedance bandwidth of VSWR < 2.5 is measured at 2.43 GHz (37.6%) centered on 6.46 GHz, from 5.24 GHz to 7.67 GHz in good agreements with the simulated results.
A hot clutter mitigation algorithm based on Subbanding and Space Fast-time Adaptive Processing (Fast-time STAP) for Multi-channel Synthetic Aperture Radar (MSAR) is analyzed, and is compared with the method based on just fast-time STAP. Simulation results demonstrate that the method based on subbanding and fast-time STAP performs better than the method based on just fast-time STAP in hot clutter mitigation for MSAR.
In this paper, a joint blind synchronization and demodulation scheme is developed for ultra-wideband (UWB) impulse radio systems. Based on the prior knowledge of the direct-sequence (DS) spread codes, the proposed approach can achieve frame-level synchronization with the help of frame-rate samples. Taking advantage of the periodicity of the DS spread codes, the frame-level synchronization can be carried out even in one symbol interval. On the other hand, after timing acquisition, these frame-rate samples can be re-utilized also for demodulation. Thus the acquisition time and the implementation complexity are reduced considerably. The performance improvement can be justified by both theoretical analysis and simulation results, in terms of acquisition probability and bit error rate (BER).
Ning GUAN Hiroiku TAYAMA Hirotaka FURUYA David DELAUNE Koichi ITO
A compact antenna is proposed for operating at the Federal Communications Commission allocated ultra-wideband (UWB) of 3.1-10.6 GHz. The antenna is made by deforming a film antenna which consists of two glass-shaped and square-shaped radiation elements. The antenna in its planar form is optimized for the UWB operation and is deformed by different manners such as folding, meandering or twisting, without much influence on its input characteristics. The deformations not only miniaturize the antenna but also improve its radiation characteristics. A prototype with a dimension of 2033 mm2 is fabricated and then the antenna is deformed by rolling it into a circular rod with a diameter of 6.4 mm, or meandering it into a square rod with a cross-sectional dimension of 65 mm2. The deformed antennas maintain the operation at the UWB and have better omni-directional radiation patterns than the antenna in its planar form.
Sathaporn PROMWONG Pichaya SUPANAKOON Jun-ichi TAKADA
A waveform of an ultra wideband impulse radio (UWB-IR) system can be extremely distorted through a channel even for free-space transmission because of antenna dispersion. This highly degrades the link budget performance. Therefore, the understand of antenna characteristics, which effects on waveform distortion, is necessary. This paper studies the waveform distortion due to antenna in free space transmission in UWB-IR system. The link budget is usually evaluated by using the Friis' transmission formula. However, it is not directly applicable to the UWB-IR transmission system. The link budget evaluation formula attended from conventional Friis' transmission formula that takes into account the transmitted waveform, its distortion due to the antennas, the channel and the correlation receiver is proposed. Since the antenna is significant pulse-shaping filters in UWB-IR system, the example kind of the log-periodic dipole antenna (LPDA) is experimentally examined, especially focused on the effect of the template waveforms.