A reduction in the intensity deviation of a nine-channel optical frequency comb block (OFCB) is demonstrated, by adopting an asymmetric differential drive method for an InP-based dual drive Mach-Zehnder modulator. The generation of a tailored OFCB with an intensity deviation of less than 0.8dB is confirmed by using the modulator.

In cognitive radio systems using TV white space, it is desirable to secure a control channel to exchange the wireless network control information and to secure minimum frequency resource for secondary user communications if TV white space is unavailable. In order to satisfy these requirements, this paper proposes guard band utilization, which aggregates the multiple guard bands between digital TV signals and uses them for a control channel and/or a communication channel. To investigate the feasibility of the proposed scheme, this paper evaluates the performance degradation of the digital TV signals when the guard band is used. Furthermore, it discusses the permissible transmitting power and occupied bandwidth of the guard band signals to avoid the harmful interference to the digital TV signals.

An amplitude shift keying transmitter and receiver chipset with low power consumption using 40nm CMOS technology for wireless communication systems is described, in which a maximum data rate of 10Gbps and power consumption of 98.4mW are obtained with a carrier frequency of 135GHz. A simple circuit and a modulation method to reduce power consumption are selected for the chipsets. To realize multi-gigabit wireless communication, the receiver is designed considering the group delay optimization. In the receiver design, the low-noise amplifier and detector are designed considering the total optimization of the gain and group delay in the millimeter-wave modulated signal region.

In this paper, we present a fully integrated single conversion front-end for a satellite low-noise block down-converter (LNB), focusing on a Ku-band noise-canceling radio frequency amplifier (RF-AMP) and an L-band intermediate frequency variable-gain amplifier (IF-VGA). LNB, which is set on a satellite dish antenna, converts the satellite signal in Ku-band (10.7GHz to 12.75GHz) to L-band (950MHz to 2150MHz). To obtain a lower noise figure (NF) at the high frequency, we implemented a wideband noise-canceling RF-AMP with an LC ladder filter. Furthermore, we implemented a current-reusing RF-AMP and mixer for lower current consumption. The IF-VGA has a constant output third-order intercept point (OIP3) for various gains thanks to a digital control of the gate width in the transconductor stage. We fabricated a single conversion front-end IC using a 1P5M 130-nm RF-CMOS process and achieved NF of 9dB and a constant OIP3 of 11dBm for various gains. The current consumption was 27mA at a 2.8-V supply voltage.

We propose an adaptive reversible data hiding method with superior visual quality and capacity in which an adaptive generalized difference expansion (AGDE) method is applied to an integer-to-integer subband transform (I2I-ST). I2I-ST performs the reversible subband transform and the AGDE method is a state-of-the-art method of reversible data hiding. The results of experiments we performed objectively and perceptually show that the proposed method has better visual quality than conventional methods at the same embedding rate due to low variance in the frequency domain.

We analyzed polarization characteristics of gammadion-shaped planar chiral nano-gratings (PCNGs), using Jones matrix and FDTD simulation. Optical activity (OA) was found to take place at wavelengths where long-lifetime modes appeared in the chiral layer. Among two kinds of resonance phenomena that concern the extension of the lifetime, guided-mode resonance and Fabry-Perot resonance, the latter was found to be a key to generate practically-important, broad peaks in the OA spectrum. Through the calculation of dispersion relations of Bloch modes in the chiral layer, we showed that the interference of multiple modes with group velocity dispersion played a critical role in the generation of such long-lifetime modes.

This paper presents an experimental study of on-body ultra-wideband (UWB) radio propagation channels within an enclosed space. To facilitate high-speed wireless body area networks, UWB is a promising technology because of its low power consumption and anti-multipath capabilities. The motivation of this study is to examine the effects of nearby humans on the UWB channels by varying the population within an elevator cabin from one (subject alone) to 20 (full capacity of the elevator). The first domain (0 < delay, t ≤ 4ns) in the measured delay profiles was either a direct (for line-of-sight) or diffracted (for non-line-of-sight) wave, which was found almost unrelated to the population; whereas the second domain (t > 4ns) highly depended on it. Total received power and delay spreads decreased with increasing the population. In addition, by varying human population, average power delay profiles were modeled based on measurements.

When attackers compromise a client system, they can steal user input. We propose a distributed one-time keyboard system to prevent information leakage via keyboard typing. We define the problem of secure keyboard arrangement over distributed multi-devices and channels. An analytical model is proposed for the optimal keyboard layout.

Silicon photonics Network-on-Chips (NoCs) have emerged as an attractive solution to alleviate the high power consumption of traditional electronic interconnects. In this paper, we propose a fully optical ring NoC that combines static and dynamic wavelength allocation communication mechanisms. A different wavelength-channel is statically allocated to each destination node for light weight communication. Contention of simultaneous communication requests from multiple source nodes to the destination is solved by a token based arbitration for the particular wavelength-channel. For heavy load communication, a multiwavelength-channel is available by requesting it in execution time from source node to a special node that manages dynamic allocation of the shared multiwavelength-channel among all nodes. We combine these static and dynamic communication mechanisms in a same network that introduces selection techniques based on message size and congestion information. Using a photonic NoC simulator based on Phoenixsim, we evaluate our architecture under uniform random, neighbor, and hotspot traffic patterns. Simulation results show that our proposed fully optical ring NoC presents a good performance by utilizing adequate static and dynamic channels based on the selection techniques. We also show that our architecture can reduce by more than half, the energy consumption necessary for arbitration compared to hybrid photonic ring and mesh NoCs. A comparison with several previous works in term of architecture hardware cost shows that our architecture can be an attractive cost-performance efficient interconnection infrastructure for future SoCs and CMPs.

In P2P applications, networks are formed by devices belonging to independent users. Therefore, routing hotspots or routing congestions are typically created by an unanticipated new event that triggers an unanticipated surge of users to request streaming service from some particular nodes; and a challenging problem is how to provide incentive mechanisms to allocation bandwidth more fairly in order to avoid congestion and other short backs for P2P QoS. In this paper, we study P2P bandwidth game — the bandwidth allocation in P2P networks. Unlike previous works which focus either on routing or on forwarding, this paper investigates the game theoretic mechanism to incentivize node's real bandwidth demands and propose novel method that avoid congestion proactively, that is, prior to a congestion event. More specifically, we define an incentive-compatible pricing vector explicitly and give theoretical proofs to demonstrate that our mechanism can provide incentives for nodes to tell the true bandwidth demand. In order to apply this mechanism to the P2P distribution applications, we evaluate our mechanism by NS-2 simulations. The simulation results show that the incentive pricing mechanism can distribute the bandwidth fairly and effectively and can also avoid the routing hotspot and congestion effectively.

The Discrete Memory Machine (DMM) is a theoretical parallel computing model that captures the essence of the shared memory access of GPUs. Bank conflicts should be avoided for maximizing the bandwidth of the shared memory access. Offline permutation of an array is a task to copy all elements in array a into array b along a permutation given in advance. The main contribution of this paper is to implement a conflict-free permutation algorithm on the DMM in a GPU. We have also implemented straightforward permutation algorithms on the GPU. The experimental results for 1024 double (64-bit) numbers on NVIDIA GeForce GTX-680 show that the straightforward permutation algorithm takes 247.8 ns for the random permutation and 1684ns for the worst permutation that involves the maximum bank conflicts. Our conflict-free permutation algorithm runs in 167ns for any permutation including the random permutation and the worst permutation, although it performs more memory accesses. It follows that our conflict-free permutation is 1.48 times faster for the random permutation and 10.0 times faster for the worst permutation.

This paper proposes a novel heterodyne multiband multiple-input multiple-output (MIMO) receiver with baseband automatic gain control (AGC) for cognitive radios. The proposed receiver uses heterodyne reception implemented with a wide-passband band-pass filter in the radio frequency (RF) stage to be able to receive signals in arbitrary frequency bands. Even when an RF Hilbert transformer is utilized in the receiver, image-band interference occurs due to the imperfection of the Hilbert transformer. In the receiver, analog baseband AGC is introduced to prevent the baseband signals exceeding the voltage reference of analog-to-digital converters (ADCs). This paper proposes a novel technique to estimate the imperfection of the Hilbert transformer in the heterodyne multiband MIMO receiver with baseband AGC. The proposed technique estimates not only the imperfection of the Hilbert transformer but also the AGC gain ratio, and analog devices imperfection in the feedback loop, which enables to offset the imperfection of the Hilbert transformer. The performance of the proposed receiver is verified by using computer simulations. As a result, the required resolution of the ADC is 9 bits in the proposed receiver. Moreover, the proposed receiver has less computational complexity than that with the baseband interference cancellation unless a frequency band is changed every 9 packets or less.

Geomagnetic information is informative because it has the ability to detect information about orientation by way of a ubiquitous device. However, a magnetic disturbance easily influences geomagnetic information. The magnetic disturbance detection method is needed in order to use geomagnetic information. Firstly, in this paper, the availability of geomagnetic information in Japan is investigated by field measurement work. Then, a new magnetic disturbance detection method which is better than the conventional method is proposed. The basic function of the proposed method is tested in actual condition.

This paper describes how to design matching structures to improve the frequency characteristics of one-dimensional finite periodic structures. In particular, it deals with one-dimensional finite superlattices. A downhill simplex method is used to determine some of the structural parameters of the matching structure. Numerical examples show that this method is effective in improving the frequency characteristics of finite superlattices.

Electromagnetic scattering and radiation in cylindrical electromagnetic bandgap (EBG) structure is analyzed. The radiated field from a line source placed inside the eccentric configuration of the cylindrical EBG structure and plane wave incident on the cylindrical EBG structure is numerically studied based on the method proposed by the authors in their early papers. Using the developed formulation, it is shown first time that when the cylindrical EBG is illuminated by plane wave of particular resonance frequencies, the field are strongly enhanced or shaded inside the cylindrical EBG structure and this effect depends on the angle of incidence of the plane waves. We give a deep physical insight into explanation of this phenomenon based on the Lorentz reciprocity relation for cylindrical structures.

This paper presents an automatic gain control (AGC) system suitable for 60GHz direct conversion receivers. By using a two step gain control algorithm with high-pass filter cutoff frequency switching, the proposed AGC system realizes fast settling time and wide dynamic range simultaneously. The paper also discusses wide-bandwidth variable gain amplifier (VGA) design. By introducing digitally-controlled resistors and gain flattening capacitors, the proposed VGA realizes wide gain range while compensating gain variations due to parasitic capacitance of MOS switches. The AGC system is implemented in a transceiver chipset where RFIC and BBIC are fabricated in 90nm CMOS and 40nm CMOS respectively. The measurement shows excellent dynamic range of 47dB with +/-1dB gain accuracy within 1µs settling time, which satisfies the stringent requirements of the IEEE802.11ad standard.

In terms of the transmission-line theory, a general synthesis of a new class of optimum Chebyshev-type ultra-wideband bandpass (UWB) filter prototype composed of multistage stepped-impedance resonators (SIRs) and two short-circuited shunt stubs positioned at input- and output- ports is presented. By the comparison of the real and theoretical transfer functions, the design/characteristic equations are obtained for the design of the proposed filter prototype rather than the traditional design tables. The explicit expressions of one-stage and two-stage filters are then derived and reported. Accordingly, bandpass filters with an arbitrary FBW (Fractional Bandwidth) and passband ripple can be easily designed by solving the design equations. As an example, a 10-degree Chebyshev distributed filter (two-stage filter) with an FBW of 110% is synthesized to meet FCC's outdoor mask. The synthesized circuit model are confirmed by a commercial circuit simulator and then optimized by an EM simulator, fabricated in microstrip line and characterized by the network analyzer. The good agreements between the measured and predicted frequency responses validate the effectiveness of newly proposed filter prototype and the corresponding synthesis technique. In addition, the designed filter exhibits good characteristics of comparatively low insertion loss, quite sharp skirt, very flat group delay and good stopband (especially in lower one) as well. It should be also highlighted that, compared with the conventional filters composed merely of parallel-coupled SIRs or shunt short-circuit-stubs, the new prototype can reduce the overall length of the filter by more than 3/4λg. Moreover, in terms of the presented design technique, the proposed filter prototype can be also used to easily realize the UWB filters with an FBW even greater than 110%.

This paper presents the shadowing analysis of a body area network (BAN) diversity antenna based on the statistical measurements of the human walking motion. First, the dynamic characteristics of the arm-swing motion were measured using human subjects, and a statistical analysis was then carried out using the measured data to extract useful information for the analysis of a BAN diversity antenna. Second, the analytical results of the shadowing effects of the BAN antenna were shown based on the statistical data of the swing motion. The difference between the typical and the realistic arm-swinging models significantly affected the bit error rate (BER) characteristic of the BAN antenna. To eliminate the shadowing caused by the movement of the arms, a BAN diversity antenna was used. Particular emphasis was placed on the evaluation of the spatial separation of the diversity antennas to attain reduction of the signal-to-noise ratio (SNR) required to achieve a specific BER performance, considering the combined outcome of shadowing and multipath fading unique to BAN antenna systems. We determined that an antenna angle separation of greater than 80° is required to reduce the shadowing effects when the diversity antenna is mounted at the left waist in a symmetrical configuration. Further, an antenna angle separation of 120° is required when the diversity antenna is mounted in an asymmetric configuration.

This paper investigates space and polarization multiplexing for multichannel transmission in a 120-GHz band wireless link system. The 120-GHz-band wireless equipment employs Cassegrain antennas with a gain of about 49dBi and cross-polar discrimination of 23dB. When each of two 120-GHz wireless links transmits a 10-Gbit/s data signal in the same direction over a distance of 800m, a bit error rate (BER) of below 10-12 is obtained when the receivers are set 30m apart. When forward error correction and polarization multiplexing are used for each wireless link, we can set two wireless links within 1m of each other and obtain a BER below 10-12. Moreover, we have experimentally shown that the rain attenuation of V- and H-polarization 120-GHz-band signal is almost the same.

In this paper, we propose a novel baseband (BB) phase shifter (PS) using a fixed-gain-amplifier (FGA) matrix. The proposed BB PS consists of 5 stages of a vector synthesis type FGA matrix with in-phase/quadrature-phase (I/Q) input/output interfaces. In order to achieve low gain variation between phase shift states, 3rd to 5th stages are designed to have a phase shift of +φi and -φi (i=3,4,5). To change between +φi and -φi phase shift states, two FGAs with DC bias in-phase/out-phase switches are used. The two FGAs have the same gain, therefore ideally no gain variation can be achieved. Using this configuration, phase shift error and gain variation caused by process mismatch and temperature variation can be reduced. Fabricated 5-bit BB PS has 3-dB bandwidth of 1.05GHz, root-mean-square (rms) phase errors lower than 2.2°, rms gain variations lower than 0.42dB. Power consumption of the PS core and output buffer are 4.9mW and 14.3mW, respectively. 1-dB compression output power is -12.5dBm. The fabricated PS shows that the total phase shift error and gain variation are within the required accuracy of a 5-bit PS with no requirement of calibration.