Multi-band WDM transmission beyond the C+L-band is a promising technology for achieving larger capacity transmission by a limited number of installed fibers. In addition to the C- and L-band, we can expect to use the S-band as the next band. Although the development of optical components for new bands, particularly transceivers, entails resource dispersion, which is one of the barriers to the realization of multi-band systems, wavelength conversion by transparent all-optical signal processing enables new wavelength bandtransmission using existing components. Therefore, we proposed a transmission system including a new wavelength band such as the S-band and made it possible to use a transceiver for the existing band by performing the whole-band wavelength conversion without using a transceiver for the new band. As a preliminary verification to demonstrate multi-band WDM transmission including S-band, we investigated the application of a novel wavelength converter between C-band and S-band, which consists of periodically poled lithium niobate waveguide, to the proposed system. We first characterized the conversion efficiency and noise figure of the wavelength converter and estimated the transmission performance of the system through the wavelength converter. Using the evaluated wavelength converters and test signals of 64 channels arranged in the C-band at 75-GHz intervals, we constructed an experimental setup for S-band transmission through an 80-km standard single-mode fiber. We then demonstrated error-free transmission of real-time 400-Gb/s DP-16QAM signals after forward error correction decoding. From the experimental results, it was clarified that the wavelength converter which realizes the uniform lossless conversion covering the whole C-band effectively achieves the S-band WDM transmission, and it was verified that the capacity improvement of the multi-band WDM system including the S-band can be expected by applying it in combination with the C+L-band WDM system.

With the gradually increase of the application of new energy in microgrids, Electric Spring (ES), as a new type of distributed compensation power electronic device has been widely studied. The Generalized Electric Spring (G-ES) is an improved topology, and the space limitation problem in the traditional topology is solved. Because of the mode of G-ES use in the power grid, a reasonable solution to the voltage loss of the critical section feeder is needed. In this paper, the voltage balance equation based on the feedforward compensation coefficient is established, and a two cascade control strategy based on the equation is studied. The first stage of the two cascade control strategy is to use communication means to realize the allocation of feedforward compensation coefficients, and the second stage is to use the coefficients to realize feedforward fixed angle control. Simulation analysis shows that the proposed control strategy does not affect the control accuracy of the critical load (CL), and effectively improves the operational range of the G-ES.

Multi-core fiber (MCF) is one of the promising space-division multiplexing technologies to increase the capacity of optical networks. MCF-based networks have two challenges. One is the inter-core crosstalk (XT) that degrades the quality of optical signals in two neighboring fiber cores. The other is network protection against link failures that cause massive data loss. One way to protect against multiple link failures is to prepare physically separated links as a backup network. Probabilistic protection improves the efficiency of protection by allowing a certain probability of protection failure. Existing studies on backup network design with probabilistic protection do not target MCF-based networks, which raises problems such as protection failure due to the inter-core XT and excessive consumption of optical resources. To address these problems, this paper proposes a XT-aware backup network design model for the MCF optical path networks. The proposed model protects the network against probabilistic multiple link failures. We adopt probabilistic protection that allows a certain probability of protection failure due to the inter-core XT and minimizes the required number of links in the backup network. We present an algorithm to satisfy the probabilistic protection requirement and formulate the model as an integer linear programming problem. We develop a heuristic approach to apply the proposed model to larger networks. Numerical results observe that the proposed model requires fewer links than the dedicated allocation model, which provisions the backup paths in the same manner as the primary paths.

In this paper, a wireless communication network that uses unmanned aerial vehicles (UAVs) in the sky to transmit information between ground users is considered. We highlight a delay-tolerant network, where information is relayed in a store-and-forward fashion by establishing two types of intermittent communication links: between a UAV and a user (UAV-to-user) and between UAVs (UAV-to-UAV). Thus, a flight algorithm that controls the movement of the UAVs is crucial in achieving rapid information transmission. Our study proposes new flight algorithms that simultaneously consider the two types of communication links. In UAV-to-UAV links, the direct information transmission between two UAVs and the indirect transmission through other UAVs are considered separately. The movement of the UAVs is controlled by solving an optimization problem at certain time intervals, with a variable consideration ratio of the two types of links. In addition, we investigate not only the case where all UAVs move cooperatively but also the case where each UAV moves autonomously. Simulation results show that the proposed algorithms are effective. Moreover, they indicate the existence of an optimal consideration ratio of the two types of communication and demonstrate that our approach enables the control of frequencies of establishing the communication links. We conclude that increasing the frequency of indirect communication between UAVs improves network performance.

The Common Media Application Format (CMAF) is a standard for adaptive bitrate live streaming. The CMAF adapts chunk encoding and enables low-latency live streaming. However, conventional bandwidth estimation for adaptive bitrate streaming underestimates bandwidth because download time is affected not only by network bandwidth but also by the idle times between chunks in the same segment. Inaccurate bandwidth estimation decreases the quality of experience of the streaming client. In this paper, we propose a chunk-grouping method to estimate the available bandwidth for adaptive bitrate live streaming. In the proposed method, by delaying HTTP request transmission and bandwidth estimation using grouped chunks, the client estimates the available bandwidth accurately due to there being no idle times in the grouped chunks. In addition, we extend the proposed method to dynamically change the number of grouping chunks according to buffer length during downloading of the previous segment. We evaluate the proposed methods under various network conditions in order to confirm the effectiveness of the proposed methods.

When mission-critical applications are provided over a network, high availability is required in addition to a low delay. This paper proposes a multi-homing network design model, named MHND, that achieves low delay, high availability, and the order guarantee of events. MHND maintains the event occurrence order with a multi-homing configuration using conservative synchronization. We formulate MHND as an integer linear programming problem to minimize the delay. We prove that the distributed server allocation problem with MHND is NP-complete. Numerical results indicate that, as a multi-homing number, which is the number of servers to which each user belongs, increases, the availability increases while increasing the delay. Noteworthy, two or more multi-homing can achieve approximately an order of magnitude higher availability compared to that of conventional single-homing at the expense of a delay increase up to two times. By using MHND, flexible network design is achieved based on the acceptable delay in service and the required availability.

Non-Terrestrial-Network (NTN) can provide seamless and ubiquitous connectivity of massive devices. Thus, the feeder links between satellites and gateways need to provide essentially high data transmission rates. In this paper, we focus on a typical high-capacity scenario, i.e., LEO-IoT, to find an optimal satellite selection schema to maximize the capacity of feeder links. The proposed schema is able to obtain the optimal mapping among all the satellites and gateways. By comparing with maximum service time algorithm, the proposed schema can construct a more balanced and reasonable connection pattern to improve the efficiency of the gateways. Such an advantage will become more significant as the number of satellites increases.

This study proposed a novel decoupling method for four planar inverted-F antennas (PIFAs) operating at 2.0GHz (f0). The edge-to-edge and center-to-center spacings of the adjacent PIFAs are extremely small (0.05λ0 and 0.17λ0, respectively), resulting in strong mutual coupling among them. In our previous study, we proposed a structure consisting of parasitic elements (PEs) and a bridge line (BL) for the decoupling of two PIFAs. One attractive feature of the proposed method is that no adjustment of the original structure and size of the PIFAs is necessary. However, as the number of PIFAs increases to four, their decoupling becomes considerably more complicated, and impedance mismatch is also an issue to be considered. Therefore, in this study, PEs and BLs are functionally developed to simultaneously achieve low mutual coupling and improved impedance matching of the four PIFAs. The simulated results showed that loading the proposed PEs and BLs onto the four PIFAs could reduce as well as maintain all mutual coupling for less than -10dB, and simultaneously improve impedance matching. Therefore, the total antenna efficiency at 2.0GHz could be significantly improved from 64.2% to 84.8% for PIFA1 and PIFA4, and from 35.9% to 74.2% for PIFA2 and PIFA3. Four PIFAs with PEs and BLs were fabricated and measured to validate the simulation results.

Vibrating intrinsic reverberation chamber is being used as an in-situ EMC test equipment for large and complex systems such as automobiles and aircrafts. In this paper, the stirring conditions, such as tightness and shaking amplitude of the walls, of a vibrating intrinsic reverberation chamber have been analyzed using the method of moments. From the viewpoint of quantitative evaluation of the flexible moving walls configuration, it was found that the random electromagnetic environment can be generated under the stirring conditions of loose configuration and a shaking amplitude more than one eighth of the wavelength at the test frequency above the lowest usable frequency.

In this paper, a nonlinear quantized precoding scheme for low-resolution digital-analog converters (DACs) in a massive multiple-input multiple-output (MIMO) system is proposed. The nonlinear quantized precoding determines transmit antenna outputs with a transmit symbol and channel state information. In a full-digital massive MIMO system, low-resolution DACs are used to suppress power consumption. Conventional precoding algorithms for low-resolution DACs do not optimize transmit antenna gains individually. Thus, in this paper, a precoding scheme that optimizes individual transmit antenna gains as well as the DAC outputs is proposed. In the proposed scheme, the subarray of massive MIMO antennas is treated virtually as a single antenna element. Numerical results obtained through computer simulation show that the proposed precoding scheme achieves bit error rate performance close to that of the conventional precoding scheme with much smaller antenna gains on a CDL-A channel.

In this study, an overloaded large-scale distributed antenna network is considered, for which the number of active users is larger than that of antennas distributed in a base station coverage area (called a cell). To avoid overload, users in each cell are divided into multiple user groups, and, to reduce the computational complexity required for multi-user multiple-input and multiple-output (MU-MIMO), users in each user group are grouped into multiple user clusters so that cluster-wise distributed MU-MIMO can be performed in parallel in each user group. However, as the network size increases, conventional computational methods may not be able to solve combinatorial optimization problems, such as user scheduling and user clustering, which are required for performing cluster-wise distributed MU-MIMO in a finite amount of time. In this study, we apply quantum computing to solve the combinatorial optimization problems of user scheduling and clustering for an overloaded distributed antenna network and propose a quantum computing-based user scheduling and clustering method. The results of computer simulations indicate that as the technology of quantum computers and their related algorithms evolves in the future, the proposed method can realize large-scale dense wireless systems and realize real-time optimization with a short optimization execution cycle.

This paper extends our previously reported non-orthogonal multiple access (NOMA)-based highly-efficient and low-latency hybrid automatic repeat request (HARQ) method for ultra-reliable low latency communications (URLLC) to the case with inter-base station cooperation. In the proposed method, delay-sensitive URLLC packets are preferentially multiplexed with best-effort enhanced mobile broadband (eMBB) packets in the same channel using superposition coding to reduce the transmission latency of the URLLC packet while alleviating the throughput loss in eMBB. Although data transmission to the URLLC terminal is conducted by multiple base stations based on inter-base station cooperation, the proposed method allocates radio resources to URLLC terminals which include scheduling (bandwidth allocation) and power allocation at each base station independently to achieve the short transmission latency required for URLLC. To avoid excessive radio resource assignment to URLLC terminals due to independent resource assignment at each base station, which may result in throughput degradation in eMBB terminals, we employ an adaptive path-loss-dependent weighting approach in the scheduling-metric calculation. This achieves appropriate radio resource assignment to URLLC terminals while reducing the packet error rate (PER) and transmission delay time thanks to the inter-base station cooperation. We show that the proposed method significantly improves the overall performance of the system that provides simultaneous eMBB and URLLC services.

This paper proposes overloaded multiple input multiple output (MIMO) bi-directional communication with physical layer network coding (PLNC) to enhance the transmission speed in heterogeneous wireless multihop networks where the number of antennas on the relay is less than that on the terminals. The proposed overloaded MIMO communication system applies precoding and relay filtering to reduce computational complexity in spite of the transmission speed. An eigenvector-based filter is proposed for the relay filter. Furthermore, we propose a technique to select the best filter among candidates eigenvector-based filters. The performance of the proposed overloaded MIMO bi-directional communication is evaluated by computer simulation in a heterogeneous wireless 2-hop network. The proposed filter selection technique attains a gain of about 1.5dB at the BER of 10-5 in a 2-hop network where 2 antennas and 4 antennas are placed on the relay and the terminal, respectively. This paper shows that 6 stream spatial multiplexing is made possible in the system with 2 antennas on the relay.

Radar-based sensing and concealed weapon detection technologies have been attracting attention as a measure to enhance security screening in public facilities and various venues. For these applications, the security check must be performed without impeding the flow of people, with minimum human effort, and in a non-contact manner. We developed technologies for a high-throughput walk-through security screening called Invisible Sensing (IVS) and implemented them in a prototype system. The IVS system consists of dual planar radar panels facing each other and carries out an inspection based on a multi-region screening approach as a person walks between the panels. Our imaging technology constructs a high-quality radar image that compensates for motion blur caused by a person's walk. Our detection technology takes multi-view projected images across the multiple regions as input to enable real-time whole-body screening. The IVS system runs its functions by pipeline processing to achieve real-time screening operation. This paper presents our IVS system along with these key technologies and demonstrates its empirical performance.

In this study, we propose a method for localizing an unknown moving emitter by measuring a sequence of the frequency-of-arrival using a single moving observation platform. Furthermore, we introduce the position and velocity errors of the moving observation platform into the theoretical localization error equation to analyze the effect of these errors on the localization accuracy without Monte-Carlo simulations. The proposed theoretical error equation can propagate toward the time direction; therefore, the theoretical localization error can be evaluated at an arbitral time. We demonstrate that the localization error value obtained by the proposed equation and the RMSE evaluated by the Monte-Carlo simulation sufficiently coincide with one another.

This paper presents a compact fully-differential distributed amplifier using a coupled inductor. Differential distributed amplifiers are widely required in optical communication systems. Most of the distributed amplifiers reported in the past are single-ended or pseudo-differential topologies. In addition, the differential distributed amplifiers require many inductors, which increases the silicon cost. In this study, we use differentially coupled inductors to reduce the chip area to less than half and eliminate the difficulties in layout design. The challenge in using coupled inductors is the capacitive parasitic coupling that degrades the flatness of frequency response. To address this challenge, the odd-mode image parameters of a differential artificial transmission line are derived using a simple loss-less model. Based on the analytical results, we optimize the dimensions of the inductor with the gradient descent algorithm to achieve accurate impedance matching and phase matching. The amplifier was fabricated in 0.18-µm CMOS technology. The core area of the amplifier is 0.27 mm2, which is 57% smaller than the previous work. Besides, we demonstrated a small group delay variation of ±2.7 ps thanks to the optimization. the amplifier successfully performed 30-Gbps NRZ and PAM4 transmissions with superior jitter performance. The proposed technique will promote the high-density integration of differential traveling wave devices.

This paper demonstrates a phase compensation technique using varactors for variable-gain phase shifters (VGPSs). The VGPS consists of an I/Q generator and I/Q variable gain amplifiers (I/Q VGAs). I/Q VGAs based on common-emitter stages are enabled to control the gain by adjusting the collector current of the transistor. However, the phase control performance degenerates because the input capacitance varies with the collector current. The proposed phase compensation technique reduces the variation in the insertion phase of the I/Q VGA by adjusting the voltage of the varactor provided at its input and maintaining the input capacitance constant in any gain state. As a result, the VGPS can provide a low phase and amplitude error under phase control. A Ka-band VGPS with the proposed phase compensation technique, fabricated in a 130-nm SiGe BiCMOS process, demonstrates a 0.73° and 0.06 dB improvement in the RMS phase and amplitude error compared with the case without the compensation technique. The VGPS achieves measured RMS amplitude and phase errors of less than 0.19 dB and 0.75°, respectively, in an amplitude control range of more than 20 dB with a frequency range of 28 to 32 GHz.

This contribution introduces a novel, dielectric waveguide based, permittivity sensor. Next to the fundamental hybrid mode theory, which predicts exceptional wave propagation behavior, a design concept is presented that realizes a pseudo-transmission measurement approach for attenuating feed-side reflections. Furthermore, a transmission line length independent signal processing is introduced, which fosters the robustness and applicability of the sensor concept. Simulation and measurement results that prove the sensor concept and validate the high measurement accuracy, are presented and discussed in detail.

This paper formulates a class-E synchronous RF rectifier from a new viewpoint. The key point is to introduce a matrix and convolute the DC terms into RF matrices. The explicit expression of input impedance is demonstrated in plane geometry. We find out their input impedance exhibits a geodesic arc in hyperbolic geometry under ZVS operation, where the theoretical RF-DC conversion efficiency results in 100%. We verify the developed theory both numerically (circuit simulation) and experimentally (6.78MHz, 100W). We confirm that the input impedance becomes a geodesic arc for a wide range of DC load resistance. The presented theory is quite elegant since it is based on a matrix-based formulation and plane-geometrical expression.

The generation and reduction reaction of magnesium plasma were studied using a cylindrical transverse magnetic-mode applicator in magnetic and electric field modes. By heating Mg powder using the magnetic field mode, plasma was generated with the evaporation of Mg and stably sustained. When the Mg plasma sample was introduced into the reaction zone and exposed to microwave and lamp heating, a reduction reaction of scandium oxide also occurred. The results of this study provide prospects for the development of a larger microwave refining system.