Visible light communication (VLC) and visible light ranging are applicable techniques for intelligent transportation systems (ITS). They use every unique light-emitting diode (LED) on roads for data transmission and range estimation. The simultaneous VLC and ranging can be applied to improve the performance of both. It is necessary to achieve rapid data rate and high-accuracy ranging when transmitting VLC data and estimating the range simultaneously. We use the signal modulation method of pulse-width modulation (PWM) to increase the data rate. However, when using PWM for VLC data transmission, images of the LED transmitters are captured at different luminance levels and are easily saturated, and LED saturation leads to inaccurate range estimation. In this paper, we establish a novel simultaneous visible light communication and ranging system for ITS using PWM. Here, we analyze the LED saturation problems and apply bicubic interpolation to solve the LED saturation problem and thus, improve the communication and ranging performance. Simultaneous communication and ranging are enabled using a stereo camera. Communication is realized using maximal-ratio combining (MRC) while ranging is achieved using phase-only correlation (POC) and sinc function approximation. Furthermore, we measured the performance of our proposed system using a field trial experiment. The results show that error-free performance can be achieved up to a communication distance of 55 m and the range estimation errors are below 0.5m within 60m.

A super-resolution algorithm is proposed to solve the problem of measuring the thin thickness of oil slick using compressed sensing theory. First, a mathematical model of a single pulse underwater ultrasonic echo is established. Then, the estimation model of the transmit time of flight (TOF) of ultrasonic echo within oil slick is given based on the sparsity of echo signals. At last, the super-resolution TOF value can be obtained by solving the sparse convex optimization problem. Simulations and experiments are conducted to validate the performance of the proposed method.

The estimation problem of structured clutter covariance matrix (CCM) in space-time adaptive processing (STAP) for airborne radar systems is studied in this letter. By employing the prior knowledge and the persymmetric covariance structure, a new estimation algorithm is proposed based on the whitening ability of the covariance matrix. The proposed algorithm is robust to prior knowledge of different accuracy, and can whiten the observed interference data to obtain the optimal solution. In addition, the extended factored approach (EFA) is used in the optimization for dimensionality reduction, which reduces the computational burden. Simulation results show that the proposed algorithm can effectively improve STAP performance even under the condition of some errors in prior knowledge.

In this paper, a novel reconfigurable intelligent surface (RIS)-aided full-duplex (FD) cooperative non-orthogonal multiple access (CNOMA) network is investigated over Nakagami-m fading channels, where two RISs are employed to help the communication of paired users. To evaluate the potential benefits of our proposed scheme, we first derive the closed-form expressions of the outage probability. Then, we derive users' diversity orders according to the asymptotic approximation at high signal-to-noise-ratio (SNR). Simulation results validate our analysis and reveal that users' diversity orders are affected by their channel fading parameters, the self-interference of FD, and the number of RIS elements.

In order to improve the anomaly detection efficiency of network traffic, firstly, the model is established for network flows based on complex networks. Aiming at the uncertainty and fuzziness between network traffic characteristics and network states, the deviation extent is measured from the normal network state using deviation interval uniformly, and the intuitionistic fuzzy sets (IFSs) are established for the various characteristics on the network model that the membership degree, non-membership degree and hesitation margin of the IFSs are used to quantify the ownership of values to be tested and the corresponding network state. Then, the knowledge measure (KM) is introduced into the intuitionistic fuzzy weighted geometry (IFWGω) to weight the results of IFSs corresponding to the same network state with different characteristics together to detect network anomaly comprehensively. Finally, experiments are carried out on different network traffic datasets to analyze the evaluation indicators of network characteristics by our method, and compare with other existing anomaly detection methods. The experimental results demonstrate that the changes of various network characteristics are inconsistent under abnormal attack, and the accuracy of anomaly detection results obtained by our method is higher, verifying our method has a better detection performance.

Solar power is the most widely used renewable energy source, which reduces pollution consequences from using conventional fossil fuels. However, supplying stable power from solar power generation remains challenging because it is difficult to forecast power generation. Accurate prediction of solar power generation would allow effective control of the amount of electricity stored in batteries, leading in a stable supply of electricity. Although the number of power plants is increasing, building a solar power prediction model for a newly constructed power plant usually requires collecting a new training dataset for the new power plant, which takes time to collect a sufficient amount of data. This paper aims to develop a highly accurate solar power prediction model for multiple power plants available for both new and existing power plants. The proposed method trains the model on existing multiple power plants to generate a general prediction model, and then uses it for a new power plant while waiting for the data to be collected. In addition, the proposed method tunes the general prediction model on the newly collected dataset and improves the accuracy for the new power plant. We evaluated the proposed method on 55 power plants in Japan with the dataset collected for two and a half years. As a result, the pre-trained models of our proposed method significantly reduces the average RMSE of the baseline method by 73.19%. This indicates that the model can generalize over multiple power plants, and training using datasets from other power plants is effective in reducing the RMSE. Fine-tuning the pre-trained model further reduces the RMSE by 8.12%.

This paper introduces a deep reinforcement learning approach to solve the virtual network function scheduling problem in dynamic scenarios. We formulate an integer linear programming model for the problem in static scenarios. In dynamic scenarios, we define the state, action, and reward to form the learning approach. The learning agents are applied with the asynchronous advantage actor-critic algorithm. We assign a master agent and several worker agents to each network function virtualization node in the problem. The worker agents work in parallel to help the master agent make decision. We compare the introduced approach with existing approaches by applying them in simulated environments. The existing approaches include three greedy approaches, a simulated annealing approach, and an integer linear programming approach. The numerical results show that the introduced deep reinforcement learning approach improves the performance by 6-27% in our examined cases.

In this paper, user set selection in the allocation sequences of round-robin (RR) scheduling for distributed antenna transmission with block diagonalization (BD) pre-coding is proposed. In prior research, the initial phase selection of user equipment allocation sequences in RR scheduling has been investigated. The performance of the proposed RR scheduling is inferior to that of proportional fair (PF) scheduling under severe intra-cell interference. In this paper, the multi-input multi-output technology with BD pre-coding is applied. Furthermore, the user equipment (UE) sets in the allocation sequences are eliminated with reinforcement learning. After the modification of a RR allocation sequence, no estimated throughput calculation for UE set selection is required. Numerical results obtained through computer simulation show that the maximum selection, one of the criteria for initial phase selection, outperforms the weighted PF scheduling in a restricted realm in terms of the computational complexity, fairness, and throughput.

High-accuracy wideband signal transmission is essential for 5G and Beyond wireless communication systems. Memory nonlinearity in transmitters is a serious issue for the goal, because it deteriorates the quality of signal and lowers the system performance. This paper studies a post-reception nonlinear compensation (PRC) schemes consisting of frequency domain equalizers (FDEs) and a blind nonlinear compensator (BNLC). A frequency-domain memory nonlinearity modeling approach is employed, and several PRC configurations with FDEs and BNLC are evaluated through computer simulations. It is concluded that the proposed PRC schemes can effectively compensate memory nonlinearity in wideband transmitters via frequency-selective propagation channel. By implementing the PRC in a base station, uplink performance will be enhanced without any additional cost and power consumption in user terminals.

Autonomous driving technology is expected to be applied to various applications with unmanned vehicles (UVs), such as small delivery vehicles for office supplies and smart wheelchairs. UV remote control by a cloud server (CS) would achieve cost-effective applications with a large number of UVs. In general, dead time in real-time feedback control reduces the control accuracy. On remote path tracking control by the CS, UV control accuracy deteriorates due to transmission delay and jitter through the Internet. Digital twin computing (DTC) and jitter buffer are effective to solve this problem. In our previous study, we clarified effectiveness of them in UV remote control by CS. The jitter buffer absorbs the transmission delay jitter of control signals. This is effective to achieve accurate UV remote control. Adaptive buffering time optimization according to real-time transmission characteristics is necessary to achieve more accurate UV control in CS-based remote control system with DTC and jitter buffer. In this study, we proposed a method for the adaptive optimization according to real-time transmission delay characteristics. To quantitatively evaluate the effectiveness of the method, we created a UV remote control simulator of the control system. The results of simulations quantitatively clarify that the adaptive optimization by the proposed method improves the UV control accuracy.

Hardware oriented security and trust of semiconductor integrated circuit (IC) chips have been highly demanded. This paper outlines the requirements and recent developments in circuits and packaging systems of IC chips for security applications, with the particular emphasis on protections against physical implementation attacks. Power side channels are of undesired presence to crypto circuits once a crypto algorithm is implemented in Silicon, over power delivery networks (PDNs) on the frontside of a chip or even through the backside of a Si substrate, in the form of power voltage variation and electromagnetic wave emanation. Preventive measures have been exploited with circuit design and packaging technologies, and partly demonstrated with Si test vehicles.

This paper proposes a layer-wise tunable retraining method for edge FeFET Computation-in-Memory (CiM) to compensate the accuracy degradation of neural network (NN) by FeFET device errors. The proposed retraining can tune the number of layers to be retrained to reduce inference accuracy degradation by errors that occur after retraining. Weights of the original NN model, accurately trained in cloud data center, are written into edge FeFET CiM. The written weights are changed by FeFET device errors in the field. By partially retraining the written NN model, the proposed method combines the error-affected layers of NN model with the retrained layers. The inference accuracy is thus recovered. After retraining, the retrained layers are re-written to CiM and affected by device errors again. In the evaluation, at first, the recovery capability of NN model by partial retraining is analyzed. Then the inference accuracy after re-writing is evaluated. Recovery capability is evaluated with non-volatile memory (NVM) typical errors: normal distribution, uniform shift, and bit-inversion. For all types of errors, more than 50% of the degraded percentage of inference accuracy is recovered by retraining only the final fully-connected (FC) layer of Resnet-32. To simulate FeFET Local-Multiply and Global-accumulate (LM-GA) CiM, recovery capability is also evaluated with FeFET errors modeled based on FeFET measurements. Retraining only FC layer achieves recovery rate of up to 53%, 66%, and 72% for FeFET write variation, read-disturb, and data-retention, respectively. In addition, just adding two more retraining layers improves recovery rate by 20-30%. In order to tune the number of retraining layers, inference accuracy after re-writing is evaluated by simulating the errors that occur after retraining. When NVM typical errors are injected, it is optimal to retrain FC layer and 3-6 convolution layers of Resnet-32. The optimal number of layers can be increased or decreased depending on the balance between the size of errors before retraining and errors after retraining.

This paper describes an in-depth analysis of crosstalk in a high-bandwidth 3D-stacked memory using a multi-hop inductive coupling interface and proposes two countermeasures. This work analyzes the crosstalk among seven stacked chips using a 3D electromagnetic (EM) simulator. The detailed analysis reveals two main crosstalk sources: concentric coils and adjacent coils. To suppress these crosstalks, this paper proposes two corresponding countermeasures: shorted coils and 8-shaped coils. The combination of these coils improves area efficiency by a factor of 4 in simulation. The proposed methods enable an area-efficient inductive coupling interface for high-bandwidth stacked memory.

Series-connection of resonant-tunneling diodes (RTDs) has been considered to be efficient in upgrading the output power when it is introduced to oscillator architecture. This work is for clarifying the same architecture also contributes to increasing oscillation frequency because the device parasitic capacitance is reduced M times for M series-connected RTD oscillator. Although this mechanism is expected to be universal, we restrict the discussion to the recently proposed multiphase oscillator utilizing an RTD oscillator lattice loop. After explaining the operation principle, we evaluate how the oscillation frequency depends on the number of series-connected RTDs through full-wave calculations. In addition, the essential dynamics were validated experimentally in breadboarded multiphase oscillators using Esaki diodes in place of RTDs.

We propose a radio-over-fiber (RoF) system with 1-bit outphasing modulation. The proposed RoF system does not require a power-hungry digital-to-analog converter in access points and relaxes the operation speed of optical transceivers to reduce device cost. We introduce two configurations to enable 1-bit outphasing modulation in our system; mixed-signal and all-digital configurations. In the mixed-signal configuration, the effects of harmonics and phase/amplitude mismatch on the adjacent channel leakage ratio (ACLR) were analyzed through simulation, and wideband transmission with a signal bandwidth of 400 MHz was experimentally verified, complying with the 3rd Generation Partnership Project (3GPP) standard for millimeter-wave band. Moreover, wide-band transmission with a signal bandwidth of 1 GHz was also experimentally verified for beyond-5G and 6G. The all-digital configuration can be implemented in a standard digital design flow. This configuration was also verified to comply with the 3GPP standard by properly selecting the intermediate and sampling frequencies to mitigate the effects of folded harmonics and quantization noise. Finally, the proposed RoF system with both configurations has been shown to have a higher bandwidth efficiency compared with other systems complying with the 3GPP standard for the ACLR. Therefore, the proposed RoF system provides a cost-effective in-building wireless solution for 5G and 6G mobile network systems.

This paper presents a hippocampal cognitive prosthesis chip designed for restoring the ability to form new long-term memories due to hippocampal system damage. The system-on-chip (SOC) consists of a 16-channel micro-power low-noise amplifier (LNA), high-pass filters, analog-digital converters (ADCs), a 16-channel spike-sorter, a generalized Laguerre-Volterra model multi-input, multi-output (GLVM-MIMO) hippocampal processor, an 8-channel neural stimulator and peripheral circuits. The proposed LNA achieved a voltage gain of 50dB, input-referred noise of 3.95µVrms, and noise efficiency factor (NEF) of 3.45 with the power consumption of 3.3µW. High-pass filters with a 300-Hz bandwidth are used to filter out the unwanted local field potential (LFP). 4 12-bit successive approximation register (SAR) ADCs with a signal-to-noise-and-distortion ratio (SNDR) of 63.37dB are designed for the digitization of the neural signals. A 16-channel spike-sorter has been integrated in the chip enabling a detection accuracy of 98.3% and a classification accuracy of 93.4% with power consumption of 19µW/ch. The MIMO hippocampal model processor predict output spatio-temporal patterns in CA1 according to the recorded input spatio-temporal patterns in CA3. The neural stimulator performs bipolar, symmetrical charge-balanced stimulation with a maximum current of 310µA, triggered by the processor output. The chip has been fabricated in 40nm standard CMOS technology, occupying a silicon area of 3mm2.

This study proposes a low-complexity permittivity estimation for ground penetrating radar applications based on a contrast source inversion (CSI) approach, assuming multilayered ground media. The homogeneity assumption for each background layer is used to address the ill-posed condition while maintaining accuracy for permittivity reconstruction, significantly reducing the number of unknowns. Using an appropriate initial guess for each layer, the post-CSI approach also provides the dielectric profile of a buried object. The finite difference time domain numerical tests show that the proposed approach significantly enhances reconstruction accuracy for buried objects compared with the traditional CSI approach.

High-performance deep neural network (DNN)-based systems are in high demand in edge environments. Due to its high computational complexity, it is challenging to deploy DNNs on edge devices with strict limitations on computational resources. In this paper, we derive a compact while highly-accurate DNN model, termed dsODENet, by combining recently-proposed parameter reduction techniques: Neural ODE (Ordinary Differential Equation) and DSC (Depthwise Separable Convolution). Neural ODE exploits a similarity between ResNet and ODE, and shares most of weight parameters among multiple layers, which greatly reduces the memory consumption. We apply dsODENet to a domain adaptation as a practical use case with image classification datasets. We also propose a resource-efficient FPGA-based design for dsODENet, where all the parameters and feature maps except for pre- and post-processing layers can be mapped onto on-chip memories. It is implemented on Xilinx ZCU104 board and evaluated in terms of domain adaptation accuracy, inference speed, FPGA resource utilization, and speedup rate compared to a software counterpart. The results demonstrate that dsODENet achieves comparable or slightly better domain adaptation accuracy compared to our baseline Neural ODE implementation, while the total parameter size without pre- and post-processing layers is reduced by 54.2% to 79.8%. Our FPGA implementation accelerates the inference speed by 23.8 times.

The issue of a low minority class identification rate caused by data imbalance in anomaly detection tasks is addressed by the proposal of a GAN-SR-based intrusion detection model for industrial control systems. First, to correct the imbalance of minority classes in the dataset, a generative adversarial network (GAN) processes the dataset to reconstruct new minority class training samples accordingly. Second, high-dimensional feature extraction is completed using stacked asymmetric depth self-encoder to address the issues of low reconstruction error and lengthy training times. After that, a random forest (RF) decision tree is built, and intrusion detection is carried out using the features that SNDAE retrieved. According to experimental validation on the UNSW-NB15, SWaT and Gas Pipeline datasets, the GAN-SR model outperforms SNDAE-SVM and SNDAE-KNN in terms of detection performance and stability.

The total number of solar power-producing facilities whose Feed-in Tariff (FIT) Program-based ten-year contracts will expire by 2023 is expected to reach approximately 1.65 million in Japan. If the facilities that produce or consume renewable energy would increase to reach a large number, e.g., two million, blockchain would not be capable of processing all the transactions. In this work, we propose a blockchain-based electricity-tracking platform for renewable energy, called ‘ZGridBC,’ which consists of mutually cooperative two novel decentralized schemes to solve scalability, storage cost, and privacy issues at the same time. One is the electricity production resource management, which is an efficient data management scheme that manages electricity production resources (EPRs) on the blockchain by using UTXO tokens extended to two-dimension (period and electricity amount) to prevent double-spending. The other is the electricity-tracking proof, which is a massive data aggregation scheme that significantly reduces the amount of data managed on the blockchain by using zero-knowledge proof (ZKP). Thereafter, we illustrate the architecture of ZGridBC, consider its scalability, security, and privacy, and illustrate the implementation of ZGridBC. Finally, we evaluate the scalability of ZGridBC, which handles two million electricity facilities with far less cost per environmental value compared with the price of the environmental value proposed by METI (=0.3 yen/kWh).