A novel activation method for a B dopant implanted in a Si substrate using a soft X-ray undulator was examined. As the photon energy of the irradiated soft X-ray approached the energy of the core level of Si 2p, the activation ratio increased. The effect of soft X-ray irradiation on B activation was remarkable at temperatures lower than 400°C. The activation energy of B activation by soft X-ray irradiation (0.06 eV) was lower than that of B activation by furnace annealing (0.18 eV). The activation of the B dopant by soft X-ray irradiation occurs at low temperature, although the activation ratio shows small values of 6.2×10-3 at 110°C. The activation by soft X-ray is caused not only by thermal effects, but also electron excitation and atomic movement.

Visible light communication is one of the key technologies for intelligent transport systems (ITS). However, current visible light communication systems require high-cost devices, such as high-speed image sensors, to support their high transmission rates. In this paper, we designed a communication system with combination of a low-speed commercial image sensor and a polygon mirror — namely, a fast-blinking light signal is scanned by the polygon mirror and captured as a residual image on the low-speed image sensor — to achieve visible light communication on existing mobile devices with high transmission rates. We also analyzed some required conditions, such as the relationship between the exposure time of the image sensor and the optimal resolution, and conducted experiments for performance evaluation. As a result, we found that the proposed system could achieve a data rate of 120bps, 10 times faster than that of the existing scheme when we compare them using the same image sensor. We also found that the proposed system can achieve a practical bit error rate in a low-noise environment.

This paper describes the circuit design and measurement results of a new GaAs-HBT RF power detector proposed for use in WiMAX and wireless LAN transmitter applications. The detector, which is based on a simple current-mirror topology, occupies a small die area. It is, therefore, not only easy to implement together with a GaAs-HBT power amplifier, but can also offer approximately logarithmic (linear-in-dB) characteristics. Because it can also be driven with small voltage amplitudes, it is suitable for base-terminal monitoring at an HBT power stage. When the detector is used as a base-terminal power monitor, an appropriate base resistance added to the detection HBT effectively suppresses frequency dispersion of the detected voltage characteristics. Measurements of a prototype detector incorporated into a single-stage HBT power amplifier fabricated on the same die are as follows. The detector is capable of delivering a detected voltage of 0.35-2.5 V with a slope of less than 0.17 V/dB over a 4-to-24-dBm output power range at 3.5 GHz while drawing a current of less than 1.8 mA from a 2.85-V supply. While satisfying a log conformance error of less than 1 dB over an amplifier output power range from 4 dBm to 24 dBm, it can also suppress the detected power dispersion within 0.18 dB at approximately 15 dBm of output power over a 3.1-3.9-GHz-wide frequency range. This dispersion value is approximately one-tenth that of a conventional collector-terminal-monitor-type diode detector.

The Earth's ionosphere can hinder radio propagation with two serious problems: group delay and phase advance. Ionospheric irregularities are significantly troublesome since they make the amplitude and phase of the radio signals fluctuate rapidly, which is known as ionospheric scintillation. Severe ionospheric scintillation could cause loss of phase lock, which would degrade the positioning accuracy and affect the performance of navigation systems. Based on the phase screen model, this paper presents a novel power spectrum model of phase scintillation and a model of amplitude scintillation. Preliminary results show that, when scintillation intensity increases, the random phase and amplitude fluctuations become stronger, coinciding with the observations. Simulations of the scintillation effects on the acquisition of Beidou signals predict acquisition probability. In addition, acquisition probabilities of GPS and Beidou signals under different scintillation intensities are presented. And by the same SNR the acquisition probability decreases when the scintillation intensity increases. The simulation result shows that scintillation could cause the loss of the acquisition performance of Beidou navigation system. According to the comparison of Beidou and GPS simulations, the code length and code rate of satellite signals have an effect on the acquisition performance of navigation system.

Irreversible k-conversion set is introduced in connection with the mathematical modeling of the spread of diseases or opinions. We show that the problem to find a minimum irreversible 2-conversion set can be solved in O(n2log 6n) time for graphs with maximum degree at most 3 (subcubic graphs) by reducing it to the graphic matroid parity problem, where n is the number of vertices in a graph. This affirmatively settles an open question posed by Kyncl et al. (2014).

A 60-GHz CMOS transmitter with on-chip antenna for high-speed short-range wireless interconnections is presented. The radiation gain of the on-chip antenna is doubled using helium-3 ion irradiation technique. The transmitter core is composed of a resistive-feedback RF amplifier, a double-balanced passive mixer, and an injection-locked oscillator. The wideband and power-saving design of the transmitter core guarantees the low-power and high-data-rate characteristic. The transmitter fabricated in a 65-nm CMOS process achieves 5-Gb/s data rate with an EVM performance of $-$12 dB for BPSK modulation at a distance of 1,mm. The whole transmitter consumes 17,mW from a 1.2-V supply and occupies a core area of 0.64,mm$^{2}$ including the on-chip antenna. The gain-enhanced antenna together with the wideband and power-saving design of the transmitter provides a low-power low-cost full on-chip solution for the short-range high-data-rate wireless communication.

In this paper, we propose a 3rd-order nonlinear IIR filter for compensating nonlinear distortions of loudspeaker systems. Nonlinear distortions are common around the lowest resonance frequency for electrodynamic loudspeaker systems. One interesting approach to compensating nonlinear distortions is to employ a mirror filter. The mirror filter is derived from the nonlinear differential equation for loudspeaker systems. The nonlinear parameters of a loudspeaker system, which include the force factor, stiffness, and so forth, depend on the displacement of the diaphragm. The conventional filter structure, which is called the 2nd-order nonlinear IIR filter that originates the mirror filter, cannot reduce nonlinear distortions at high frequencies because it does not take into account the nonlinearity of the self-inductance of loudspeaker systems. To deal with this problem, the proposed filter takes into account the nonlinearity of the self-inductance and has a 3rd-order nonlinear IIR filter structure. Hence, this filter can reduce nonlinear distortions at high frequencies while maintaining a lower computational complexity than that of a Volterra filter-based compensator. Experimental results demonstrate that the proposed filter outperforms the conventional filter by more than 2dB for 2nd-order nonlinear distortions at high frequencies.

Chronic liver disease is a major worldwide health problem. Diagnosis and staging of chronic liver diseases is an important issue. In this paper, we propose a quantitative method of analyzing local morphological changes for accurate and practical computer-aided diagnosis of cirrhosis. Our method is based on sparse and low-rank matrix decomposition, since the matrix of the liver shapes can be decomposed into two parts: a low-rank matrix, which can be considered similar to that of a normal liver, and a sparse error term that represents the local deformation. Compared with the previous global morphological analysis strategy based on the statistical shape model (SSM), our proposed method improves the accuracy of both normal and abnormal classifications. We also propose using the norm of the sparse error term as a simple measure for classification as normal or abnormal. The experimental results of the proposed method are better than those of the state-of-the-art SSM-based methods.

Sound field reproduction systems seek to realistically convey 3D spatial audio by re-creating the sound pressure inside a region enclosing the listener. High-order Ambisonics (HOA), a sound field reproduction technology, is notable for defining a scalable encoding format that characterizes the sound field in a system-independent way. Sound fields sampled with a particular microphone array and encoded into the HOA format can be reproduced using any sound presentation device, typically a loudspeaker array, by using a HOA decoder. The HOA encoding format is based on the spherical harmonic decomposition; this makes it easier to design a decoder for large arrays of loudspeakers uniformly distributed over all directions. In practice, it is seldom possible to cover all directions with loudspeakers placed at regular angular intervals. An irregular array, one where the angular separation between adjacent loudspeakers is not constant, does not perform as well as a regular one when reproducing HOA due to the uneven sampling of the spherical harmonics. This paper briefly introduces the techniques used in HOA and advances a new approach to design HOA decoders for irregular loudspeaker arrays. The main difference between conventional methods and our proposal is the use of a new error metric: the radial derivative of the reconstruction error. Minimizing this metric leads to a smooth reproduction, accurate over a larger region than that achieved by conventional HOA decoders. We evaluate our proposal using the computer simulation of two 115-channel loudspeaker arrays: a regular and an irregular one. We find that our proposal results in a larger listening region when used to decode HOA for reproduction using the irregular array. On the other hand, applying our method matches the high-quality reproduction that can be attained with the regular array and conventional HOA decoders.

A low VDD current mirror with deep sub-micron vertical MOSFETs is presented. The keys are new bias circuits to reduce both the minimum VDD for the operation and the sensitivity of the output current on VDD. In the simulation, our circuits reduce the minimum VDD by about 17% and the VDD sensitivity by one order both from those of the conventional. In the simulation with 90nm φ vertical MOSFET approximate models, our circuit shows about 4MΩ output resistance at 1.2-V VDD with the small temperature dependence, which is about six times as large as that with planar MOSFETs.

380keV proton irradiation effects are investigated on p-GaN and n-GaN layers in GaN-based light emitting diode (LED) by characterizing current-voltage (I-V) characteristics of p-n junction, and two-terminal resistance of p- and n-GaN on both type of layers in LED wafer. Two-terminal resistance on n-GaN kept its initial value after the 1×1014cm-2 fluence, and was remained the same order after the 1×1015cm-2 fluence. On the other hand, p-GaN showed sensitive increase in two-terminal resistance after the 1×1014cm-2, and six orders of increase after the 1×1015cm-2 fluence. Observed sensitive increase of resistivity in p-GaN is explained as a lower initial hole density in p-GaN than the initial electron density in n-GaN layer.

As one of organic electroluminescent (EL) materials, we developed a method of fabricating an ink using low molecular- weight materials with a long emission lifetime for application to the inkjet method. Although the emission lifetime is usually long for low molecular-weight materials, their high manufacturing cost due to the necessity of vapor deposition is a disadvantage. We utilized the low molecular-weight material, tris-(8-hydroxyquinoline) aluminum (Alq3), and investigated its dispersibility in a solvent in which it has low solubility. In addition, we ascertained whether the material could maintain its photoluminescence characteristic under the irradiation of ultraviolet rays by investigating the emission of photoluminescence. Alq3 was crystallized into nanosize crystals, whose surface was then coated with a primary amine by the gas evaporation method. The fabricated ink contained crystals with an average size of 250nm and high dispersibility in tetradecane, in which Alq3 is insoluble. Thus, we made it possible to carry out an inkjet method with low molecular weight EL materials.

A shift of finite type (SFT) is a set of all bi-infinite sequences over some alphabet which is characterized by a finite set of forbidden words. It is a typical example of sofic shifts and has been used in media storage area, such as CD's or DVD's. The study of sofic shifts is based on graph theory, and the irreducibility of shifts is an important property to be considered for the study. In this paper, we will provide some sufficient conditions for an SFT to be irreducible from the perspective of the antidictionary of a word and the number of forbidden words. We also present a necessary and sufficient condition for an SFT to be irreducible when the number of forbidden words is one less than the alphabet size.

Traditional imperfect fault coverage models only consider the coverage (including identification and isolation) of faulty components, and they do not consider the coverage of irrelevant (operational) components. One potential reason for the omission is that in these models the system is generally assumed to be coherent in which each component is initially relevant. In this paper, we first point out that an initially relevant component could become irrelevant afterwards due to the failures of some other components, and thus it is important to consider the handling of irrelevancy even the system is originally coherent. We propose an irrelevancy coverage model (IRCM) in which the coverage is extended to the irrelevant components in addition to the faulty components. The IRCM can not only significantly enhance system reliability by preventing the future system failures resulting from the not-covered failures of the irrelevant components, but may also play an important role in efficient energy use in practice by timely turning off the irrelevant components.

Polarization-maintaining photonic crystal fiber couplers (PM-PCFCs) were fabricated using a CO2 laser irradiation technique. We could control the states of air holes in the tapered region of couplers by adjusting the laser power density in the fusion and the elongation processes. It was demonstrated that the air hole remaining PM-PCFC exhibited polarization-splitting characteristics and that the air hole collapsed PM-PCFC had polarization insensitive coupling characteristics.

This paper presents a method to improve field uniformity using two TX antennas in a reverberation chamber with less steps of a stirrer. A mode-stirred reverberation chamber (MSRC) is considered as an alternative to the semi-anechoic chamber for an electromagnetic compatibility test because it provides a large test volume, a statistically uniform field, and a high maximum electric field. To improve field uniformity, we introduce two transmitting antennas for excitation in an MSRC, and predict statistical distribution of the complex reflection coefficients (scattering parameters). To prove the validation of our theory and the reliability of measurement results, three kinds of stirrers with different shape and sizes were fabricated and their efficiencies were measured in an MSRC, and then field uniformities have been investigated for 1–3 GHz frequency within the maximum number of independent samples that stirrers can provide. The measurement results show that the average received power is about 1.5 times as high as when using one transmitting antenna, and field uniformity is improved. Use of two transmitting antennas in an MSRC is regarded as a useful method to improve field uniformity at less stirrer steps, for radiated immunity tests.

A flexible and computationally efficient method for spectral analysis of sinusoidal signals using the Basis Pursuit De-Noising (BPDN) is proposed. This method estimates a slotted Auto-Correlation Function (ACF) and computes the spectrum as the sparse representation of the ACF in a dictionary of cosine functions. Simulation results illustrate flexibility and effectiveness of the proposed method.

Mirrored serpentine microstrip lines are proposed for a parallel high speed digital signaling to reduce the peak far-end crosstalk (FEXT) voltage. Mirrored serpentine microstrip lines consist of two serpentine microstrip lines, each one equal to a conventional normal serpentine microstrip line. However, one serpentine microstrip line of the mirrored serpentine microstrip lines is flipped in the length direction, and thus, two serpentine microstrip lines face each other. Time domain reflectometry measurements show that the peak FEXT voltage of the mirrored serpentine microstrip lines is reduced by 56.4% of that of conventional microstrip lines and 30.0% of that of conventional normal serpentine microstrip lines.

In this brief paper, both static and dynamic behaviors of an electrostatic-actuated MEMS mirror are modeled and studied. To overcome the intrinsic pull-in problem and the dynamic disadvantages in the open-loop controlled actuation, a novel closed-loop feedback control method is proposed assuming the mirror tilt angle can be measured. First, a fixed voltage slightly higher than the pull-in voltage is applied when the mirror tilt angle is small. Then Proportional-Derivative (PD) control is used when the mirror is approaching the target position. Simulink simulation results show that this combined PD closed-loop control can overcome the pull-in problem and improve the dynamic behavior; furthermore, it can also enhance the robustness of the mirror actuation system to overcome environmental disturbances.

In this letter, the compensation ability of nonlinear distortions for loudspeaker systems is demonstrated using dynamic distortion measurement. Two linearization methods using a Volterra filter and a Mirror filter are compared. The conventional evaluation utilizes swept multi-sinusoidal waves. However, it is unsatisfactory because wideband signals such as those of music and voices are usually applied to loudspeaker systems. Hence, the authours use dynamic distortion measurement employing a white noise. Experimental results show that the two linearization methods can effectively reduce nonlinear distortions for wideband signals.