It is important to analyze a tracking or synchronizing process in Spread Spectrum (SS) receiving system. The most common SS tracking system considered here consists of pseudorandom (PN) generator, Lowpass Filter (LPE) and Voltage Controlled Oscillator (VCO). The SS receiver is to track or synchronize its local PN generator to the received PN waveform by VCO. The fundamental equation of the system is known by a second order nonlinear differential equation in terms of phase difference between local PN generator and received PN waveform. The differential equation is nonautonoumous due to PN function of time t with period T. Picking up the gain of VCO as the main parameter in the system we show that the system has bifurcation from the normal oscillation through subharmonic oscillation to finally chaos. In the final case, chaos is confirmed by investigating maximum Liapunov number and both stable and unstable manifolds.

An exact solution of the propagation constant of a cylindrical waveguide has been obtained in the event of the conductivity of the waveguide-composing conductor being finite. The said analysis has been reduced to a problem to solve a transcendental equation concerning an eigenvalue of the individual modes of the in-guide electromagnetic wave, and calculation of Jn-1(z)/Jn(z) by using of Bessel function becomes necessary. With a large conductivity the absolute value of the complex number z becomes excessively large, and none of calculation method with high accuracy has been found with the aid of a computer. This paper has solved the problem by using a continued fraction for the calculation with regard to which a recurrence formula is utilized. With the TE01 wave that has conventionally been used as a millimeter-wave guide, it is cleared that it is sufficient to select the number of the calculation terms of the continued fraction to the extent of approximately 1000 in the accuracy in accordance with this calculation method. It is also cleared that the approximation solution obtained by a method of perturbation coincides with the exact solution for the conductivity σ 102 [S/m].

The buried oxide nonintegrities, represented as the equivalent fixed oxide charge and interface trap densities at both the upper and lower interface of buried oxide, are evaluated for low-dose and high-dose SIMOX wafers, and their effects on device characteristics are investigated. The equivalent fixied oxide charge and trap densities at the lower interface, which are measured with buried oxide capacitors, are negligibly small in as-fabricated SIMOX wafers. This result enables us to make an analytical model of the parasitic drain/source-to-substrate capacitance in an SOI MOSFET, in which the effect of the depletion layer under the buried oxide is considered. The influence of thinner buried oxide and process-induced fixed oxide charge on the parasitic capacitance is explored with this model. The equivalent fixed oxide charge and trap densities at the upper interface are evaluated by the threshold voltage measurement in an SOI NMOSFET. The principle of this evaluation as well as the experimental technique are described in detail. The oxide charge and trap densities at the upper interface are higher than those at the lower interface for both SIMOX wafers. With a new model of the subthreshold slope based on a two-dimensional potential analysis the influence of the trap at the upper interface is discussed.

This paper proposes novel optical path accommodation design algorithms for networks wherein the number of wavelengths multiplexed into a fiber is restricted. This algorithm optimizes both optical path route and wavelength assignment in VWP/WP networks. It minimizes optical path cross-connect (OPXC) system scale in terms of incoming/outgoing fiber port numbers. A comparison in terms of required OPXC system scale between the WP and VWP schemes is demonstrated for the first time.

The two-dimensional scattering problem of electromagnetic waves by a perfectly conducting wedge is analyzed by means of the Wiener-Hopf technique together with the formulation using the partition of scatterers. The Wiener-Hopf equations are derived on two complex planes. Investigating the mapping between these complex planes and introducing the appropriate functions which satisfy the edge condition of the wedge, the solutions of these equations are obtained by the decomposition procedure of functions. By deforming the integration path of the Fourier inverse transform, it is found that the representation of the scattered wave is in agreement with the integral representation using the Sommerfeld contours.

To connect among many radio base stations by using optical fiber bus link in microcellular system, subcarrier multiplexing (SCM) is excellent in simplicity and flexibility. But performance degradation due to optical beat noises is severe problem. To solve this problems, this paper proposes a new type of intercell connection bus fiber-optic link (ICBL) using time division multiplexing, called TDM-ICBL. This paper also analyzes transmission performance of TDM-ICBL theoretically and compares with SCM-ICBL. The analysis clarifies that while the number of RBSs connected to SCM-ICBL is severely restricted by beat noises, TDM-ICBL is more useful than SCM-ICBL when there are many number of connected RBSs.

In this paper, we study the following node-to-node fault tolerant routing problem: In the presence of up to n-1 faulty nodes, find a fault-free path which connects any two non-faulty nodes s and t in an n-connected graph. For node-to-node fault tolerant routing in n-dimensional hypercubes Hn, we give an algorithm which finds a fault-free path s t of length at most in O(n) time, where d(s, t) is the distance between s and t. We also show that a fault-free path s t in Hn of length at most d(s, t)2i, 1i, can be found in time. For node-to-node fault tolerant routing in n-dimensional star graphs Gn, we give an algorithm which finds a fault-free path s t of length at most min{d(Gn)3, d(s, t)6} in O(n) time, where is the diameter of Gn. It is previously known that, in Hn, a fault-free path s t of length at most d(s, t) for d(s, t)n and at most d(s, t)2 for d(s, t)n can be found in O(d(s, t)n) time, and in Gn, a fault-free path s t of length at most min{d(Gn)1, d(s, t)4}can be found in O(d(s, t)n) time. When the time efficiency of finding the routing path is more important than the length of the path, the algorithms in this paper are better than the previous ones.

This paper describes newly developed miniaturized stepped impedance resonators with a double coaxial structure (DC-SIR's) and their application to bandpass filters. The new DC-SIR's using dielectric material are devised for more compact and lower frequency bandpass filters. Fundamental characteristics such as resonance properties and unloaded-Q make it clear that DC-SIR's have attractive features that miniaturization can be achieved without Q-factor degradation. Trial 400 MHz bandpass filters incorporating DC-SIR's are also made. Experimental results of bandpass filters proved that DC-SIR's are applicable to lower frequency band radio equipment and able to contribute to the expansion of applicable frequency ranges of dielectric coaxial resonators.

The investigation of device functions required from the systems point of view will be important for the development of the next generation of VLSI devices and systems. In this paper, a super pass transistor (SPT) model is presented as a quantum device candidate for future VLSI systems based on multiple-valued logic. A possible quantum device structure for the SPT model is also described, which employs the concepts of a lateral-resonant-tunneling quantum-dot transistor and a heterostructure field-effect transistor. Since it has the powerful capability of detecting multiple signal levels, the SPT will be useful for the implementation of highly compact multiple-valued VLSI systems. To exploit the functionality of the SPT, a super pass gate (SP-gate) corresponding to a single SPT is proposed as a multiple-valued universal logic module. The mathematical properties of the SP-gate are discussed. A design method for a multiple-valued SP-gate network is presented. An application of SP-gates to a multiple-valued image processing system is also demonstrated. The SP-gate network for the multiple-valued image processing system is evaluated in comparison with the corresponding NMOS implementation in terms of the number of transistors, interconnections and cascaded transistor stages. The size of a generalized series-parallel SP-gate network is also evaluated in comparison with a functionally equivalent multiple-valued series-parallel MOS pass transistor network. The results show that highly compact multiple-valued VLSI systems can be achieved if the SPT-model can be realized by an actual quantum device.

To support high bit rate and high quality indoor radio communication systems, we have to solve intersymbol interference (ISI) problem caused by frequency-selective fading. Recently multi-carrier modulation technique is considered to be one of the effective methods for this problem. In this paper we propose Partial Frequency ARQ (Automatic Repeat reQuest) system which can achieve effective ARQ scheme for multi-carrier packet communication. This system operates partial retransmission of erroneous power faded packets, and it is superior to the traditional ARQ systems. Furthermore two different protocols are examined for this system: Static Carrier Assignment (SCA) and Dynamic Carrier Assignment (DCA). By computer simulation we found that DCA method can achieve better performance than SCA in terms of both throughput and packet transmission delay.

Standard Site Method (SSM) is theoretically analyzed using matrix representations to examine its validity and develop an improved method. The analysis reveals that the SSM yields an antenna factor specifically related to the effective load impedance presented by the cable and associated devices which are disconnected from the antenna during the SSM site attenuation measurements. Therefore, an additional conversion is required to determine the desired antenna factor under actual load conditions. It is also concluded that the SSM is not applicable to antennas having height-dependent antenna factors. In addition, the SSM correction factors are found to be theoretically inappropriate. Uncertainty of the antenna factor obtained using the SSM is discussed and the required antenna separation distance is investigated. To improve the existing SSM, it is proposed that both transmitting and receiving antennas are placed at the same height during the site attenuation measurements. Experiments exhibit the superiority of the improved method.

In this paper we will propose a deterministic approach to model the radio propagation channels complex indoor environments. This technique applies the SBR method to find equivalent sources (images) in each launched ray tube, and sums the receiving amplitude contributed by all images coherently. We verify our SBR/image approach by comparing the numerical results in two canonical examples where closed-form solutions exist. The good agreement indicates that our method can provide a good approximation of high frequency radio propagation inside corridors where reflection is dominant. In the special case of a curved corridor, which can not be solved by analytic methods, we find a "focusing" effect that at some certain point the receiver will receive high power, even though it is out of sight. This SBR/image method can be enhanced by including the wall penetration and wedge diffraction effects, and even more complicated indoor environments will be tackles in the near future.

In this paper, we propose two parallel processing methods for multidimensional (MD) sampling lattice alteration. The use of our proposed methods enables us to alter the sampling lattice of a given MD signal sequence in parallel without any redundancy caused by up- and down-sampling, even if the alteration is rational and non-separable. Our proposed methods are provided by extending two conventional block processing techniques for FIR filtering: the overlap-add method and the overlap-save method. In these proposed methods, firstly a given signal sequence is segmented into some blocks, secondly sampling lattice alteration is implemented for each block data individually, and finally the results are fitted together to obtain the output sequence which is identical to the sequence obtained from the direct sampling lattice alteration. Besides, we provide their efficient implementation: the DFT-domain approach, and give some comments on the computational complexity in order to show the effectiveness of our proposed methods.

This paper presents an improved neural network for channel assignment problems in cellular mobile communication systems in the new co-channel interference model. Sengoku et al. first proposed the neural network for the same problem, which can find solutions only in small size cellular systems with up to 40 cells in our simulations. For the practical use in the next generation's cellular systems, the performance of our improved neural network is verified by large size cellular systems with up to 500 cells. The newly defined energy function and the motion equation with two heuristics in our neural network achieve the goal of finding optimum or near-optimum solutions in a nearly constant time.

In this paper, we presented an analysis of single and coupled microstrip lines covered with protective dielectric film which is usually used in the microwave integrated circuits. The method employed in the characterization is called partial-boundary element method (p-BEM). The p-BEM provides an efficient means to the analysis of the structures with multilayered media or covered with protective dielectric film. The numerical results show that by changing the thickness of the protective dielectric films such as SiO2, Si and Polyimide covered on these lines on a GaAs substrate, the coupled microstrip lines vary within 10% on the characteristic impedance and within 25% on the effective dielectric constant for the odd mode of coupled microstrip line, respectively, in comparison with the structures without the protective dielectric film. In contrast, the single microstrip lines vary within 4% on the characteristic impedance and within 8% on the effective dielectric constant, respectively. The protective dielectric film affects the odd mode of the coupled lines more strongly than the even mode and the characteristics of the single microstrip lines.

The simulation of a specific absorption rate (SAR) with a temperature distribution becomes more important in the treatment planning for microwave hyperthermia. The simulation technique can also be used to estimate SAR distribution inside human body under hazardous electromagnetic (EM) field circumstances. In the simulation, to use exact permittivity of biological tissues becomes very important to obtain accurate SAR distribution. The permittivity of the medium is very sensitive to the temperature. Therefore, it is considered that the SAR distribution is also very sensitive to the tissue temperature. In this paper, SAR distribution is calculated using FDTD method considering tissue temperature under the electromagnetic (EM) field irradiation. Simulations of temperature distribution are also performed using heat transfer equation. In addition, temperature depending blood flow is taking into account to obtain temperature depending SAR distribution. The results can be used to estimate temperature depending heat generation which can be applied such as microwave hyperthermia treatment.

The fundamental TE10 mode in a rectangular waveguide of a square cross section is degenerate with TE01 mode. A quarter wavelength resonator made of a dielectric square waveguide is, therefore, applied for a small-sized bandpass filter, just like dual mode filters for base stations in the mobile communication. In this paper, the methods to couple the two modes are first studied, including cutting a corner of the resonator and adding some metal electrodes on its end face. Both methods help to flow the rf current of the odd mode at the corner, resulting in decrease of the series inductance and thus increase of the resonant frequency. The coupling constant, that is proportional to the difference of the odd and even-mode's resonant frequency, can be controlled by the perturbations mentioned above. The coupling to the external circuit is adjusted by an electrode fabricated also on the end face. It is connected to a microstrip line and capacitively couples to the resonant modes. The coupling strength increases with the dimension of the electrode. The adjustment of the resonant frequency is carried out by the similar electrode on the end face and connected to the center of the side of the square cross section. The frequency decreases with the length of the electrode. The unloaded Q is measured to be of around 500 for 5510 mm resonator of εr=93. The optimum aspect ratio for the resonator is found in terms of the Q value. The simplest bandpass filter, i.e., a two-stage bandpass filter is designed and fabricated using 5510 mm resonator. It is mounted in a square hole made in a printed circuit board and excited by a microstrip line. The frequency characteristics are in good agreement with the expected values.

This paper proposes a symbol rate controlled adaptive modulation/TDMA/TDD for future wireless personal communication systems. The proposed system controls the symbol rate according to the channel conditions to achieve wide dynamic range of the modulation parameter control as well as to improve the delay spread immunity. The main purpose of the proposed system is to increase the data throughput with keeping a certain transmission quality, especially in frequency selective fading environments. For this purpose, the proposed system predicts the C/N0 (carrier power-to-noise spectral density ratio) and the delay spread separately, and selects the optimum symbol rate that gives the maximum bit rate within a given bandwidth satisfying the required BER. The simulated results show that the proposed system can achieve higher transmission quality in comparison with the fixed symbol rate transmission system in both flat Rayleigh and frequency selective fading environments. The results also show that the proposed system is very effective to achieve higher bit rate transmission in frequency selective fading environments.

This paper deals with a high-speed digital circuit for discrete cosine transform (DCT). We propose a new algorithm that reduces the number of calculations for partial sum-of-products in the DCT and synthesize the small gate depth circuit of DCT by using carry-propagation-free adders based on redundant binary {1,0,1} representation. The gate depth is only half to one third that of the conventional algorithms with the same number of gates.

This paper proposes a high throughput small latent IP packet delivery architecture using ATM technology in a large scaled internet. Data-link network segments, including ATM network segments, are interconnected through routers. A connection oriented IP packet delivery will be provided by IP (including both IPv4 and IPv6) with a certain resource reservation protocol (e.g. RSVP). When the router attached to ATM network segment has a mapping function between the flow-ID (e.g. in the SIPP header) and the VPI/VCI value, the small latent connection oriented IP forwarding can be provided. Also, when the router has cell-relaying functionality, the small latent connectionless IP forwarding can be provided, even in IPv4. The source router, where the source end-station belongs to, will be able to transfer the connectionless IP packet to the destination router, where the destination end-station belongs to, through the concatenated ATM connections (ATM-VCCs) without any ATM-VCC termination point. When all of the network segments are ATM-LAN, the proposed architecture can accommodate about up to 222 (4106) end-stations with two network layer processing points. And when the network is scaled up hierarchally, we can accommodate larger number of end-stations. For example, we can accommodate 1015 end-stations by a three layered network. Then the maximum number of actual network layer processing points between source and destination end-stations can be ten. Here, 1015 is the maximum number of end-stations in ISDN and also it is the target number of accommodated end-stations for IPv6.