This paper presents the implementation of a 31-tap FIR Hilbert transform digital filter chip used in the digital-IF receivers, to confirm the effectiveness of our new design method. Our design method that we previously reported is based on a computation sharing multiplier using a new horizontal and vertical common subexpression techniques. A 31-tap FIR Hilbert transform digital filter was implemented and fabricated in 0.35 µm CMOS standard cell library. The chip's core contains approximately 33k transistors and occupies 0.86 mm2. The chip also has an operating speed of 70 MHz over. The implementation results show that the proposed Hilbert transformer has a smallest cost factor and so that is a high performance filter.

In this paper, we derive an upper bound for the average block error probability of a standard irregular low-density parity-check (LDPC) code ensemble under the maximum-likelihood (ML) decoding. Moreover, we show that the upper bound asymptotically decreases polynomially with the code length. Furthermore, when we consider several regular LDPC code ensembles as special cases of standard irregular ones over an additive white Gaussian noise channel, we numerically show that the signal-to-noise ratio (SNR) thresholds at which the proposed bound converges to zero as the code length tends to infinity are smaller than those for a bound provided by Miller et al.. We also give an example of a standard irregular LDPC code ensemble which has a lower SNR threshold than a given regular LDPC code ensemble.

This paper describes two different types of GaAs-HBT compatible, base-collector diode 0/20-dB step attenuators--diode-linearizer type and harmonics-trap type--for 3.5-GHz-band wireless applications. The two attenuators use an AC-coupled, stacked type diode switch topology featuring high power handling capability with low bias current operation. Compared to a conventional diode switch topology, this topology can improve the capability of more than 6 dB with the same bias current. In addition, successful incorporation of a shunt diode linearizer and second- and third-harmonic traps into the attenuators gives the IM3 distortion improvement of more than 7 dB in the high power ranging from 16 dBm to 18 dBm even in the 20-dB attenuation mode when IM3 distortion levels are basically easy to degrade. Measurement results show that both the attenuators are capable of delivering power handling capability (P0.2 dB) of more than 18 dBm with IM3 levels of less than -35 dBc at an 18-dBm input power while drawing low bias currents of 3.8 mA and 6.8 mA in the thru and attenuation modes from 0/5-V complementary supplies. Measured insertion losses of the linearizer-type and harmonics-trap type attenuators in the thru mode are as low as 1.4 dB and 2.5 dB, respectively.

The paper presents a computer program for the calculation of contact mass loss in the case of evaporation, ablation and melting. It makes use of theoretical mathematical equations previously published by a lot of researchers. For the purposes of the program, an expert system algorithm was designed. The paper presents results obtained by means of the proposed program for silver, tungsten and copper.

Popcorn noise is a large transient noise spike at the reader shortly after writing due to unstable domains in writer yoke. The popcorn noise was found to dependent on write frequency. It is firstly reported that the popcorn noise occurred by the write instability of shielded-single-pole head (SSPH) can be captured in row-bar level QST which is experimentally confirmed. Thus, a PMR head can be rejected by the row-bar level QST. In addition, the writing stress traced by the MR transfer curve can possibly accelerate the head degradation.

Hermetically sealed electromagnetic relays (EMR) are widely used for high reliability control and executive systems as a device mechanically transferring signals. Now they are more indispensable in space engineering, such as rockets, satellites and other ground attachment, but which mechanical atmosphere is too harsh. So dynamics response of EMR is needed to satisfy particularity of such mechanical atmosphere. In this paper, a typical hermetically sealed EMR structure is modeled by using finite element analysis software-Nastran. In the meantime the equivalent spring elements are introduced to simulate the contact of normally closed contacts, and the contact between armature and iron stopper. Therefore dynamic performance of EMR under different mechanical environment, including sinusoid vibration and shock condition is investigated completely. The factors affecting normal modes and dynamic response of EMR are analyzed. Comparisons show good correlation between experimental and numerical results.

Contact resistance is caused by constriction resistance and film resistance through contact layers. It is well known that a surface film causes non-linear voltage and current characteristics. The origin of non-linearity is caused by tunneling electron through thin insulation barrier or jumping over the thick barrier (Shottky barrier) on the contact surface. In this paper, a new idea causing nonlinear property by only current constriction which flows through very small contact spot area, if there is no film layer, is proposed by the two dimensional contact model. The contact model, used in this paper, is a two dimensional type narrow path of contact area (short bridge) made by thin copper foil of 0.035 mm on a glass epoxy resin board. The contact part is made by scraping with an electric drill as a single bridge shape of 0.1 mm wide and 0.3 mm long on the centre of a board (100 mm100 mm). The 3rd harmonic distortion voltage was measured by using a Component Linearity Test Equipment (Type CLT1 made by Radiometer Electronics Company) which the system supplies a pure sine wave current of 10 kHz and detects a distortion voltage of 30 kHz by a narrow band pass filter circuit. The sensitivity of the Component Linearity Test Equipment (CLT1) is under a 10-9 volt. Four bridge samples were examined for the comparison of nonlinear distortion voltage. The distortion voltage of a sample (A) (0.1 mm wide, 0.3 mm long) is too larger than the one of the sample (B) (0.2 mm wide, 0.3 mm long) at the same applied voltage which resistance is not so different each other. It seems that current constriction to the spot (A) may heat up higher and cool down lower than (B). It would be also guessed that the power dissipation of 20 kHz cause temperature oscillation of 20 kHz, then it causes a component of contact resistance of 20 kHz, and therefore the product of 10 kHz current and 20 kHz resistance component cause 30 kHz component distortion voltage.

A persistent current switch (PCS) is used for superconducting applications, such as superconducting magnetic energy storage (SMES) system. The authors have proposed a mechanical switch of Y-Ba-Cu-O (YBCO) bulk as a mechanical PCS. In previous study, the authors have successfully reduced a residual resistance by depositing with metal on contact surface. This paper focused on a current carrying area (called a-spot) on contact surface and presented an effect of deposited metal on electrical contact characteristics in order to clear the contact mechanism. As the results of experiments and simulation using FEM, it became clear that it was effective for reducing the residual resistance from a view point of increasing the a-spot by depositing with metal.

Eddy-current type proximity sensor is a non-contact type sensing device to detect the approach of a conductor by increase of coil resistance due to eddy-current loss. This paper proposes to add the cap-shaped magnetic flux shield at the top of the ferrite core for the actual sensor. In conventional proximity sensors, main magnetic flux path passes through the air between the target conductor and ferrite core. Proposed sensor, in contrast, has closed magnetic circuit geometry. It means that main magnetic flux path is almost completed by the core and the shield. Therefore, it is predicted that flux does not reach the target conductor and it causes debasement of sensing property. However, it is shown that the calculated results by FEM and measured results of sensing property of the proposed sensor is enhanced compared with the actual sensor. This paper quantitatively accounts the electromagnetisms of the proposed sensor from sensing property, flux distributions and eddy-current loss in each part of the sensor body. Moreover, material characteristics for the proposed shield, such as relative permeability and conductivity, are found.

In orthogonal frequency-division multiplex access (OFDMA) uplink, the carrier-frequency offsets (CFOs) between the multiple transmitters and the receiver introduce inter-carrier interference (ICI) and severely degrade the performance. In this paper, based on the perfect estimation of each user's CFO, we propose two low-complexity iterative algorithms to cancel ICI due to CFOs, which are denoted as the basic algorithm and the improved algorithm with decision-feedback equalization (DFE), respectively. For the basic one, two theorems are proposed that yield a sufficient condition for the convergence of iterations. Moreover, the interference-power-evolution (IPE) charts are proposed to evaluate the convergence behavior of this interference cancellation algorithm. Motivated by the IPE chart, the procedure of DFE is introduced into the iterations, which is the basic idea of the improved algorithm. For this improved algorithm, the error-propagation effect are analyzed and suppressed by an efficient stopping criterion. From IPE charts and simulation results, it can be easily observed that the basic algorithm has the same capability of ICI cancellation as the linear optimal minimum mean square error (MMSE) method, but offers lower complexity, while the improved algorithm with DFE outperforms the MMSE method in terms of the bit-error rate (BER) performance.

This paper proposes a co-channel interference (CCI) suppression scheme employing a frequency-domain nulling filter and turbo equalizer for single-carrier uplink time division multiple access (TDMA) systems. In the proposed scheme, after the received signal is transformed into a frequency-domain signal via fast Fourier transform (FFT), CCI from an adjacent cell is suppressed by the nulling filter. Moreover, the proposed scheme employs a soft canceller and minimum mean square error (SC/MMSE) based turbo equalizer to suppress the performance degradation due to inter-symbol interference (ISI) caused by the nulling filter as well as the ISI induced by fading channel. Computer simulation confirms that the proposed scheme is effective in suppression of CCI compared to the conventional linear frequency-domain equalizer.

The traffic with asymmetry between uplink and downlink has recently been getting remarkable on mobile communication systems providing multimedia communication services. In the future mobile communications, the accommodation of asymmetric traffic is essential to realize efficient multimedia mobile communication systems. This paper discusses asymmetric traffic accommodation in CDMA/FDD cellular packet communication systems and proposes its efficient scheme using an adaptive cell sizing technique. In the proposed scheme, each base station autonomously controls its coverage area so that almost the same communication quality can be achieved across the service area under the asymmetric traffic conditions. We present some numerical examples to demonstrate the effectiveness of the proposed scheme by using computer simulation. The simulation results show that, under asymmetric traffic conditions, the proposed scheme can provide fair communication quality across the service area in both links and can improve total transmission capacity in the uplink.

The sputter erosion of arcing contacts is a very complex phenomenon, which is determined by the interaction between electromagnetic force, heat conduction and surface tension of liquid metal. A new model for evaluating the sputter erosion of electrodes is described in this paper, which is based on the electromagnetic forces against the molten pool, flowing velocity, kinetic energy and the surface tension of the molten pool. Erosion tests on AgSnO2, AgNi10 and AgNi0.15 contacts under the loads of resistance, lamp and inductance respectively at 14 VDC have been carried out. Experimental results indicate good agreement with the model's simulation. The model shows how the current and density, specific heat and other parameters of material affect the erosion rate.

We study the problem of optimizing admission control policies in mobile multimedia cellular networks when predictive information regarding movement is available and we evaluate the gains that can be achieved by making such predictive information available to the admission controller. We consider a general class of prediction agents which forecast the number of future handovers and we evaluate the impact on performance of aspects like: whether the prediction refers to incoming and/or outgoing handovers, inaccurate predictions, the anticipation of the prediction and the way that predictions referred to different service classes are aggregated. For the optimization process we propose a novel Reinforcement Learning approach based on the concept of afterstates. The proposed approach, when compared with conventional Reinforcement Learning, yields better solutions and with higher precision. Besides it tackles more efficiently the curse of dimensionality inherent to multimedia scenarios. Numerical results show that the performance gains measured are higher when more specific information is provided about the handover time instants, i.e. when the anticipation time is deterministic instead of stochastic. It is also shown that the utilization of the network is maintained at very high values, even when the highest improvements are observed. We also compare an optimal policy obtained deploying our approach with a previously proposed heuristic prediction scheme, showing that plenty of room for technological innovation exists.

For the optimization design of air circuit breaker (ACB), it is important and necessary to calculate the electro-dynamic repulsion force acting on the movable contact. A method based on 3-D FEM with the equations that describe the relationships among current, magnetic field and repulsion force, which takes the ferromagnet into account, is adopted to calculate the electro-dynamic repulsion force. The method enables one to analyze the factors that affect the electro-dynamic repulsion force, including the number of the movable conductor parallel branches as well as the location of the axis and the shape of the flexible connection. The discussion of the calculation results is also presented in this paper.

Internet access traffic follows hourly patterns that depend on various factors, such as the periods users stay on-line at the access point (e.g. at home or in the office) or their preferences for applications. The clustering of Internet users may provide important information for traffic engineering and billing. For example, it can be used to set up service differentiation according to hourly behavior, resource optimization based on multi-hour routing and definition of tariffs that promote Internet access in low busy hours. In this work, we propose a methodology for clustering Internet users with similar patterns of Internet utilization, according to their hourly traffic utilization. The methodology resorts to three statistical multivariate analysis techniques: cluster analysis, principal component analysis and discriminant analysis. The methodology is illustrated through measured data from two distinct ISPs, one using a CATV access network and the other an ADSL one, offering distinct traffic contracts. Principal component analysis is used as an exploratory tool. Cluster analysis is used to identify the relevant Internet usage profiles, with the partitioning around medoids and Ward's method being the preferred clustering methods. For the two data sets, these methods lead to the choice of 3 clusters with different hourly traffic utilization profiles. The cluster structure is validated through discriminant analysis. It is also evaluated in terms of several characteristics of the user traffic not used in the cluster analysis, such as the type of applications, the amount of downloaded traffic, the activity duration and the transfer rate, resulting in coherent outcomes.

The ESIGN signature scheme was initially proposed in 1985. Since then, several variants have been proposed, but only a few have been formally supported using the methodology of provable security. In addition, these schemes are different from the ESIGN-PSS signature scheme submitted to ISO/IEC-14888-2 for standardization. It is believed that ESIGN-PSS is secure against the chosen-message attack, however, there has not yet been any report verifying this belief. This paper presents the security proofs of ESIGN-PSS and a variant of this scheme, denoted ESIGN-PSS-R, which is a signature scheme comprising the ESIGN signature mechanism and the PSS-R mechanism.

A new hybrid model to calculate echoes and ultrasonic fields scattered by flaws is presented. In this model, transmitted fields by a transducer and fields scattered by flaws are calculated using the Rayleigh integral and the FDTD method, respectively. Received echo signals by the transducer are obtained by the inner product of the transmitted fields and the scattered ones at each grid for the FDTD method, and integrating those in a calculation area. Since the calculation area for the FDTD method can be limited around flaws, the calculation time is short and computer memory usage can be reduced. Experiments are done for two types of test object to confirm the validity of the hybrid model. As a result, experimental results are in good agreement with calculated ones.

Cooperative communication enables single antenna to realize a virtual multiple antenna by sharing their antennas. Therefore, it offers transmit diversity. In this letter, we apply pre-coding scheme to the transmit symbols. Although pre-coding has shortcomings, it is possible to employ Space-Time Block Codes (STBC) with single antenna and achieve high gain.

This paper investigates the use of the affine transformation matrix when employing principal component analysis (PCA) to compress the data of 3D animation models. Satisfactory results were achieved for the common 3D models by using PCA because it can simplify several related variables to a few independent main factors, in addition to making the animation identical to the original by using linear combinations. The selection of the principal component factor (also known as the base) is still a subject for further research. Selecting a large number of bases could improve the precision of the animation and reduce distortion for a large data volume. Hence, a formula is required for base selection. This study develops an automatic PCA selection method, which includes the selection of suitable bases and a PCA separately on the three axes to select the number of suitable bases for each axis. PCA is more suitable for animation models for apparent stationary movement. If the original animation model is integrated with transformation movements such as translation, rotation, and scaling (RTS), the resulting animation model will have a greater distortion in the case of the same base vector with regard to apparent stationary movement. This paper is the first to extract the model movement characteristics using the affine transformation matrix and then to compress 3D animation using PCA. The affine transformation matrix can record the changes in the geometric transformation by using 44 matrices. The transformed model can eliminate the influences of geometric transformations with the animation model normalized to a limited space. Subsequently, by using PCA, the most suitable base vector (variance) can be selected more precisely.