An antenna and multi-carrier combined diversity system using Time Division Duplex (TDD) is proposed to combat with multi-path channel problem which produces frequency-selective fading and degrades the quality of signal transimission. So far multi-carrier modulation technique has been studied to solve this problem. On the other hand, TDD method has been studied to use a transmitter antenna diversity as pre-diversity against flat fading (non-selective fading). Our proposed system merges these two methods in a micro-cellular system as follows. On the reverse link, the base station can select the best combination between the carriers and antennas after receiving the multi-carrier signal from the mobile station. On the forward link, the same combination selected on the reverse link can be used to send the signal from the base station with multi-antenna to the mobile station with a single antenna and produces pre-diversity (transmitter diversity) effect which can reduce the complexity at the mobile station. The pre-diversity must be based on TDD function because the channel has to be observed before the signal transimission. By computer simulations we find that our proposed system can achieve far better performance than conventional systems.

In conventional trellis coded modulation (TCM), higher-ary modulation scheme combining with a convolutional code is employed not to expand the transmitted bandwidth. This forces the system to be attended with signal constellation expansion and increasing the average signal power. As the solutions to avoid signal constellation expansion, TCM systems using totally overlapped signal sets (TO-TCM and RU-TCM) were proposed. These schemes can realize a coded modulation system without signal constellation expansion and achieve more coding gain compared with the conventional TCM. However, a problem that the systems with totally overlapped signal sets might be catastrophic has been remained. In this paper, we propose a novel TCM system using partially overlapped signal sets of non-equiprobable signaling (PO-TCM-NE). This scheme employs the partially overlapped signal constellation to control increasing signal points, and to avoid catastrophic error propagation. The non-equiprobable signaling is employed to reduce average signal power. Coding gain of the proposed PO-TCM-NE is considerably improved in consequence the average signal power is reduced much lower than that of other TCM systems with equiprobable signaling.

Introducing a mathematical model of image noise, we formalize the problem of fitting a line to point data as statistical estimation. It is shown that the reliability of the fitted line can be evaluated quantitatively in the form of the covariance matrix of the parameters. We present a numerical scheme called renormalization for computing an optimal fit and at the same time evaluating its reliability. We also present a scheme for visualizing the reliability of the fit by means of the primary deviation pair and derive an analytical expression for the reliability of a line fitted to an edge segment by using an asymptotic approximation. Our method is illustrated by showing simulations and real-image examples.

The robust statistics has recently been adopted by the computer vision community. Various robust approaches in the computer vision research have been proposed in the last decade for analyzing the image motion from the image sequence. Because of the frequent violation of the Gaussian assumption of the noise and the motion discontinuities due to multiple motions, the motion estimates based on the straightforward approaches such as the least squares estimator and the regularization often produces unsatisfactory result. Robust estimation is a promising approach to deal with these problems because it recovers the intrinsic characteristics of the original data with the reduced sensitivity to the contamination. Several previous works exist and report some isolated results, but there has been no comprehensive analysis. In this paper robust approaches to the optical flow estimation based on the maximum likelihood estimators are proposed. To evaluate the performance of the M-estimators for estimating the optical flow, comparative studies are conducted for every possible combinations of the parameters of three types of M-estimators, two types of residuals, two methods of scale estimate, and two types of starting values. Comparative studies on synthetic data show the superiority of the M-estimator of redescending ψ-function using the starting value of least absolute residuals estimator using Huber scale iteration, in comparison with the other M-estimators and least squares estimator. Experimental results from the real image experiments also confirm that the proposed combinations of the M-estimators handle the contaminated data effectively and produce the better estimates than the least squares estimator or the least absolute residuals estimator.

In this paper, oscillation modes produced in a Josephson circuit and its application to digital systems are described. The analysis is performed using an analog simulator to model the Josephson junction, in addition to computer simulation. The experimental results concerning oscillation modes agree well with the simulation results. The main advantage of the mapping for the oscillation modes is that it allows understanding of the relationships among oscillation modes and circuit parameters at first sight. In addition, a novel application of nonlinear oscillation to digital systems is described.

We have studied the performances of several types of vortex flow transistors including prototype flux flow transistors (FFTs), nanobridge vortex flow transistors (NBVFTs) based on a parallel array of nanobridges, planar Josephson vortex flow transistors (planar JVFTs) based on a parallel array of grain boundary Josephson junctions, and JVFTs with a stacked structure (stacked JVFTs). The NBVFTs had considerably higher magnetic field sensitivity and shorter response time than the FFTs. A flux-to-voltage transfer function V/φ of 2.6 m V/φo and a modulation depth of 0.5 mV were obtained for the NBVFT composed of 2 nanobridges, while the current gain was small. The temperature dependence of the device parameters (the dynamic resistance and the inductance) suggests that the surface barrier to the Abrikosov vortex entry into the nanobridge strongly contributes to the relatively large V/φ values. The response time of the nanobridge is estimated to be 5 ps. On the other hand, the JVFTs showed large current gains because of the small kinetic inductance of the Josephson junction. The planar JVFT composed of 3 Josephson junctions with an asymmetrical geometry showed a current gain of 2.2 at 4.2 K. Also, the stacked JVFT showed the current gain of 2.0, while the maximum value of V/φ was 210 µV/φo. The mutual inductance between the control line and the superconducting loop within the transistor was enhanced in the stacked JVFT. This enhancement may yield a short response time compared to that of the planar JVFT. When we apply these vortex flow transistors, we should take account of the properties peculiar to each transistor.

In the weakly coupled grain model which has been proposed to explain the residual surface resistance in high-Tc superconducting polycrystalline thin films, the superconducting polycrystalline thin films is described as a network of superconducting grains coupled via Josephson junctions. In order to evaluate this model we have fabricated the coplanar waveguide resonator using c-axis oriented YBa2Cu3Ox Thin Films and measured the residual surface resistance. The experimental results are in good agreement with theoretical prediction.

Hot-carrier degradation of voltage controlled oscillator (VCO) was investigated by a reliability simulator known as BERT. The appropriate monitor of VCO frequency degradation shifts from the saturated drain current of an N MOSFET to linear drain current with an increase in VCO input voltage. The degradation of the VCO drastically increases with a small reduction in initial oscillation frequency. These results imply the need for an appropriate reliability margin around the standard operating point as well as a performance margin, which cannot be achieved by using conventional drain current monitors.

The 4th harmonics of a Nd:YAG laser beam (266 nm) is applied to fabricate highly oriented Y1Ba2Cu3O7-δ -SrTiO3-Y1Ba2Cu3O7-δ multilayer structures. It has been shown that the emission temperature of a film surface will change during deposition, depending on deposition conditions, even though the heater temperature is constant. The change of substrate temperature is strongly correlated to film characteristics such as critical temperature, c-axis length, and resistivity. The insitu monitoring of the substrate temperature is useful for obtaining high-quality Y1Ba2Cu3O7-δ films reproducibly. It is also shown that a SrTiO3 layer prevents oxygen restoration in a Y1Ba2Cu3O7-δ underlayer. The relationship between oxygen deficiency and the annealing conditions is studied.

ISM band has been approved for spread spectrum communication in radio LAN in Japan since December 1992. This frequency band extends from 2.474 GHz to 2.5 GHz with 26 MHz bandwide. In an indoor environment, the maximum observed delay spread is 100-200 ns in a room, it is too short to generate a selective fading, thus flat fading conditions are often observed. Serve as an alleviation, we propose a new system of multi-antenna in base station (BS) and single antenna in mobile station (MS). In this system, MS should have a simple structure for its small size and energy-saving.

In this paper, we define the distortion at a certain complexity level, which is the dual quantity of the distortion-complexity. We prove a theorem dual to the theorem which we have given of the asymptotic property of the distortion-complexity. We also give a universal data-base for fixed-rate data compression with distortion and prove its asymptotic optimality.

We have developed a strato-mesospheric ozone monitoring system with a low noise SIS mixer, which receives 110.836 GHz millimeter-wave emission due to the rotational transition of ozone molecules (J=61,560,6). The system is completely standalone. We derived the altitude profile of ozone density between 25 km and 80 km from the observed spectrum. The receiver noise temperature was as low as 17 K (DSB), so that the altitude profile could be obtained every 3-10 minutes. The monitoring system can operate continuously over one year without any maintenance work, because it utilizes a 4 K closed cycle helium refrigerator and reliable Nb/AIOx/Nb SIS junctions. We used two acousto-optical spectrometers (AOSs) as real-time spectrometers because of their high resolution and simple construction. In an up-to-date system, one AOS would have a band-width of 65 MHz and the other, a band-width of 250 MHz with resolutions of 40 kHz and 250 kHz, respectively. A computer controls the entire system and is also used to analyze measured data. In this paper, we present the principles of system operation, the latest performance and the construction of the system, and some observed data.

For Nakagami-Rice fading environment which seems to become a principle propagation environment in the next generation wideband and high-capacity mobile systems such as personal communications, we have previously proposed an approximated evaluation scheme for wideband digital transmission characteristics such as errors due to intersymbol interference of multipath waves. We called the scheme 'Equivalent Transmission-Path (ETP) Model.' In this paper, through a discussion about more general equivalent propagation channel expressions, we clarify a theoretical foundation of the ETP model and extend the model to have an ability of expression of instantaneous fading condition varying with time. Also the appropriateness of the instantaneous expression is examined by a computer simulation analysis. Based on this model, statistics of link quality and service availability in Nakagami-Rice fading environments are discussed.

For direct sequence spread spectrum systems, the performance of PN sequence acquisition can be significantly affected if data modulation is present. However, the data modulation often exists during the reacquisition of a PCS radio channel. This study proposes and analyzes two shemes which are designed to improve acquisition process for PN sequence under data modulation. Both designs are based upon a PN acquisition receiver with parallel I-Q matched filters. The first scheme employs a serial search strategy with verification mode. The second scheme, which is still based upon the same parallel acquisition receiver, employs the parallel search strategy. We show that the second scheme is capable of providing faster acquisition under data modulation than the first serial search scheme using the same number of I-Q matched filter. We believe it should become a very good alternative for the acquisition of data modulated PN sequences in personal communications.

This paper compares the performance of an indoor cellular system in terms of capacity and channel assignment delay for different Dynamic Channel Assignment (DCA) and Fixed Channel Assignment (FCA) schemes. We refer to specific group of DCAs, namely Channel Segregation and Reuse Partitioning (RP). Our main concern is to show that these DCA schemes offer better performance than FCA. Since the structure and floor layout of a building will have a major influence on the propagation and hence on the cell shape, a path loss simulator is developed for predicting the path loss which is used in evolving base station layouts. Computer simulation, based on Monte Carlo method, is carried out using the path loss values and the base station layouts. The results indicate that increased traffic capacity can be achieved with all DCAs in comparison with FCA. The highest capacity and a shorter channel assignment delay are delivered by Self-Organized Reuse Partitioning DCA scheme.

This paper considers the evaluation of the acquisition performance for an access channel preamble based on the random access procedure of direct sequence code division multiple access (DS/CDMA) reverse link. The parallel acquisition technique that employs the single-dwell and multiple-dwell (double-dwell) detection schemes is investigated. The acquisition performance for two detection schemes is compared in terms of the acquisition probablity and the mean acquisition time. The parallel acquisition is done by a bank of N parallel I/Q noncoherent correlators. Expressions on the detection, false alarm, and miss probabilities of the single-dwell and multiple-dwell (double-dwell) detection schemes are derived for the multiple H1 cells and multipath Rayleigh fading channel. Comparing the single-dwell detection scheme with the multiple-dwell (double-dwell) detection scheme in the case of employing the parallel acquisition technique in the reverse link, the numerical results show that the single-dwell detection scheme provides a better performance.

Many numerical simulation problems of natural phenomena are formulated by large tridiagonal and block tridiagonal linear systems. In this paper, an efficient parallel algorithm to solve a tridiagonal linear system is proposed. The algorithm named bi-recurrence algorithm has an inherent parallelism which is suitable for parallel processing. Its time complexity is 8N - 4 for a tridiagonal linear system of order N. The complexity is little more than the Gaussian elimination algorithm. For parallel implementation with two processors, the time complexity is 4N - 1. Based on the bi-recurrence algorithm, a VLSI oriented tridiagonal solver is designed, which has an architecture of 1-D linear systolic array with three processing cells. The systolic tridiagonal solver completes finding the solution of a tridiagonal linear system in 3N + 6 units of time. A highly parallel systolic tridiagonal solver is also presented. The solver is characterized by highly parallel computability which originates in the divide-and-conquer strategy and high cost performance which originates in the systolic architecture. This solver completes finding the solution in 10(N/p) + 6p + 23 time units, where p is the number of partitions of the system.

To evaluate the coding performance of a multilevel coding scheme for Rayleigh fading channel, a virtual automatic gain control and interleaving are applied to the scheme. The automatic gain control is assumed only for the theoretical evaluation of the performance. It is noted that the bit error-rate performance of the scheme for phase shift keying does not change whether the control is assumed or not. By the effect of the virtual automatic gain control and the interleaving, a fading channel with Gaussian noise is theoretically converted into an equivalent time-invariant channel with non-Gaussian noise. The probability density function of the converted non-Gaussian noise is derived. Then, the function is applied to a formula of the bit error-rate of the scheme for non-Gaussian noise. The formula is derived for phase shift keying by modifying that for pulse amplitude modulation. The coding performance for the non-Gaussian noise channel is evaluated by the formula, and the suitable coding with ideal interleaving is searched. As a result, the coding gain of 28 dB is obtained at the bit error-rate of 10-6 by using BCH code of length 31. This result is confirmed by a simulation for the fading channel. Then, the effectiveness of the formula for finite interleaving is evaluated. Finally, the usefulness of the formula, where the noise power is doubled, is shown for a case of a differential detection.

This paper addresses the problem of estimating 3-D motion of a rigid object from a sequence of monocular 2-D images. The surface of object is assumed to be modeled with several patches, each of which is expressed by an implicit equation. The proposed method estimates the pose (i.e., the location and orientation) of object that corresponds to each image in the sequence: The sequence of the estimated poses gives the motion of the object. The estimation is done by solving a system of equations, each of which is typically an algebraic equation of low degree, that is derived from the expressions of the surface patches and image contours data: so the method does not require establishing the correspondence between successive two frames in the image sequence or computing optic flow. Allowing several-patch models for objects enables the proposed approach to deal with a great variety of objects. The paper includes a numerical example, where our aproach has been applied to a polyhedral object modeled with several patches.

For mobile/personal satellite systems, an ARQ protocol with low transmitter/receiver complexity as well as high throughput performance in a long Round-Trip-Delay (RTD) and even in a bad channel condition is required. In this paper, a new Selective-Repeat (SR) ARQ with multicopy retransmission is proposed and a performance on an AWGN channel is analyzed. The proposed scheme can be viewed as a modified version for SR + Stutter (ST) Scheme 2 [6]. The basic idea of the strategy is to repeat only erroneous blocks stored in the vN block transmitter buffer multiple times, when v consecutive retransmissions in SR mode are received in error, where N denotes RTD in blocks. Numerical analysis and simuration results in the case of N block transmitter/receiver buffer show that the proposed scheme presents better performance than SR + ST scheme 2 of 2N block buffer, especially that the robustness in the high BER region is remarkable.