Complex filters are used to synthesize real filters in digital signal processing, but few in analog one. In this paper, we propose a leapfrog synthesis of complex analog filters. By shifting frequency response of an LCR network along the ω-axis, we have a complex filter with imaginary resistances, which is called an "LCRRi filter." The complex resonator is then used to simulate series- or parallel-arms of the LCRRi filter. We analyze nonideal properties of the complex resonator due to finite gain-bandwidth product of operational amplifiers and propose a compensation method to put a pole on correct location. Experimental results show good performance of the proposed method.

Power-law decay of current for the application of step-function voltage observed for amorphous materials can be expressed by an admittance sa(0a1) of a linear diode using complex angular frequency s. It is shown that power-law decay can be interpreted as a superposition of exponential decays having fractally distributed relaxation times and simulated using RC networks. By use of a similar manner, admittance s-b (0b1) showing the relation of duality can be simulated using RL networks. According to these methods, we can synthesize the admittance involving non-integer exponents systematically.

We propose a direct-sequence spread-spectrum multi-access (DS/SSMA) receiver that incorporates multipath diversity combining and multistage co-channel interference (CCI) cancellation. This receiver structure which is more resistant to the near/far problem essentially removes more and more of the CCI with each successive cancellation stage. With the assumption that perfect channel estimates have been obtained, we analyze the bit error rate (BER) performance of this system when received powers are unequal. Results show that the BER can approach that of a single-user case as the number of CCI cancellation stages increases.

An integrator is quite a suitable active element for high-speed filters. The effect of its excess phase shifts, however, is severe in the case of high-Q filter realization. The deterioration due to the excess phase shifts cannot be avoided when only integrators are used as frequency-dependent elements like in leapfrog realization. This paper describes a design of second-order high-speed and high-Q filters with low sensitivity to excess phase shifts of integrators by adding a passive RC circuit. The proposed method can drastically reduce the effect due to the undesirable pole of an integrator, which is the cause of the excess phase shifts, compared to conventional filters using only integrators. As an example, a fourth-order bandpass filter with 5-MHz center frequency and Q=25 is implemented by the proposed method on a monolithic chip. The results obtained here show quite good agreement with the theoretical values. This demonstrates effectiveness of the proposed method and feasibility of high-speed and high-Q filters on a monolithic chip.

The inverted slot line (ISL) has been propoaed for millimeter-wave LiNbO3 optical modulator. It is simple in structure, and capable of achieving the perfect velocity matching between carrier and modulating waves. The excellent performance of the ISL optical modulator has been demonstrated at 100 GHz, and the extension into the 50 GHz range is being expected. This paper addresses the analysis of the ISL based on the spectral domain approach. The major results obtained here are the demonstration of the perfect velocity matching not only at 10 GHz but also at 50 GHz, and the characterization of the ISL in terms of effective refractive index, characteristic impedance, overlap integral factor and transmission loss. The depth of optical phase modulation is also estimated at 50 GHz to show a promising performance in the millimeter-wave frequency range. The effective refractive index and the characteristic impedance are found to be theoretically predictable, but the field profile, the overlap integral factor and the transmission loss are not necessarily in good agreement with measurements. As a result of analysis, it can be concluded that the Y-cut substrate is superior to the Z-cut substrate in the following respects: 1. Coupling with the surface wave mode hardly occurs near the operating frequency range. 2. The perfect velocity matching can be attained with a larger spacing between the electrode and the ground plane. 3. The transmission loss is smaller. 4. The field intensity and the voerlap integral factor do not seem to be much deteriorated in the actual ISL.

This paper describes design considerations for high frequency active BPFs up to 100 MHz. The major design issues for high frequency active filters are the excess phase shift in the integrators and high power consumption of the integrators. Typical bipolar transistor based transconductors such as the Gilbert gain cell and the linearized transconductor with two asymmetric emitter-coupled pairs have been analyzed and compared. It has been clarified that the power consumption of the linearized transconductor can be much smaller than that of the Gilbert gain cell because of its high transconductance to working current ratio while maintaining a signal to noise ratio of the same order. A simple high-speed fully differential linearized transconductor cell is proposed with emitter follower buffers and resistive loads for excess phase compensation. A novel gyrator based transformation for the LC ladder BPF has been introduced. This transformation has resulted in a structure with simple capacitor-coupled active resonators which exactly preserves the original transfer function. A fourth order 10.7 MHz BPF IC was designed using the proposed transconductors. It was fabricated and has demonstrated the usefulness of the proposed approach. In addition, an experimental 100 MHz second order BPF IC with Q=14 has been successfully implemented indicating the potential of the proposed approach.

This paper describes an automatic transistor model parameter generation technique for a circuit simulator which can take device geometry into account. An 'area factor' is used to generate model parameters for different transistor shapes; however, the conventional method could not reflect the actual geometry differences other than for the emitter area. This resulted in inaccurate model parameters and such parameters were not acceptable to accurately simulate circuits for RF ICs. The proposed technique uses actually measured parameters and process data for a reference transistor and generates the individual model parameters for different shape transistors. In this technique, the parasitic resistor values are calculated and fitted in place of directly extracting them from the measured data. This ensures a better estimate. The reference transistor is made sufficiently large to neglect measurement errors in generating the parasitic capacitors. Thus, the model parameters for a very small transistor can be generated accurately. The model generating procedure has been implemented as a pre-processor to SPICE. This technique enables a fast turn around for RF IC circuit design which uses various shape transistors.

A method for the recognition of Arabic printed scripts entered from an image scanner is presented. The method uses the Hough transformation (HT) to extract features, Dynamic programming (DP) matching technique, and a topological classifier to recognize the characters. A process of characters recognition is further divided into four parts: preprocessing, segmentation of a word into characters, features extraction, and characters identification. The preprocessing consists of the following steps: smoothing to remove noise, baseline drift correction by using HT, and lines separation by making an horizontal projection profile. After preprocessing, Arabic printed words are segmented into characters by analysing the vertical and the horizontal projection profiles using a threshold. The character or stroke obtained from the segmentation process is normalized in size, then thinned to provide it skeleton from which features are extracted. As in the procedure of straight lines detection, a threshold is applied to every cell and those cells whose count is greater than the threshold are selected. The coordinates (R, θ) of the selected cells are the extracted features. Next, characters are classified in two steps: In the first one, the character main body is classified using DP matching technique, and features selected in the HT space. In the second one, simple topological features extracted from the geometry of the stress marks are used by the topological classifier to completely recognize the characters. The topological features used to classify each type of the stress mark are the width, the height, and the number of black pixels of the stress marks. Knowing both the main group of the character body and the type of the stress mark (if any), the character is completely identified.

This paper proposes and investigates an adaptive equalizer with diversity-combining over a multipath fading channel. It consists of two space-diversity antennas and a Ts/2-spaced decision-feedback-equalizer (DFE). Received signals from the two antennas are alternatively switched and fed into the feed forward-filter of DFE. We call this structure a Switched Input Combining Equalizer with diversity-combining (SICE). By using an SICE, the receiver structure for combining diversity equalization can be simplified, because it needs only two receiver sections up to IF BPF. The bit error rate (BER) performance of SICE was evaluated by both computer simulation and experiment over a multipath fading channel. We experimentally confirmed the excellent BER performance, around 1% of BER over a multipath fading channel at 160Hz of maximum doppler fading frequency. Therefore, the proposed SICE is applicable to highly reliable transmission in the 1.5-GHz-band mobile radio.

An RF IC for a 1.1-V VHF paging receiver is developed. In order to reduce the number of components, it employs direct-conversion frequency shift keying (FSK) architecture. The RF IC adopts two new gain control circuits so as to achieve a wide input dynamic range with only a 1.1 V power supply. One is a low-voltage, low-noise, low-distortion RF amplifier and the other is a low-voltage AGC amplifier. By applying these new circuit technologies, the RF IC achieves a voltage gain of 50.5 dB and a noise figure of 4.3 dB with only 2.0 mW power consumption. Overall, the paging receiver achieves a high sensitivity of -130 dBm and low-intermodulation sensitivity of -37 dBm with bit error rate of 310-2. This paper describes the new high-frequency low-voltage circuit technologies applied in the RF IC.

An optical On-Off Keyed (OOK) pulse is often stretched in dispersive channels, thus producing intersymbol interference (ISI) and degrading the performance. In this paper, error probability is presented for a convolutionally encoded optical OOK channels with ISI. Both ISI-matched and ISI-mismatched decoders are taken into account in the error probability analysis. The encoded optical OOK signal is received by Avalanche Photo Diode (APD) and the number of APD output photo-electrons is counted for soft decision Viterbi decoding. Error probability is derived for a 3-bit and an ideal soft decision schemes in ISI-mismatched decoder and for an ideal soft decision scheme in ISI-matched decoder. Numerical results demonstrate the effects of mismatching or 3-bit soft decision scheme. Some computer simulations are carried out to confirm the validity of the analysis.

A new theoretical propagation model for wideband fading channel simulation in mobile radio environments is presented. It is based on a path model which produces scattered waves according to Poisson process. The typical properties of transmission characteristics deduced from the theoretical and experimental studies are taken in the model. Using the propagation model, an analytical method for the near-far problem of CDMA in mobile radio environments is proposed. An example of the analysis by means of a simulation is also presented.

In general, the work on developing an expert system has relied on domain experts to provide all domain-specific knowledge. The method for acquiring knowledge directly from experts is inadequate in oriental medicine because it is hard to find an appropriate expert and the development cost becomes too high. Therefore, we have developed two effective methods for acquiring knowledge indirectly from sample cases. One is to refine a constructed knowledge base by using sample cases. The other is to train a neural network by using sample cases. To demonstrate the effectiveness of our methods, we have implemented two prototype systems; the Oriental Medicine Expert System (OMES) and the Oriental Medicine Neural Network (OMNN). These systems have been compared with the system with the knowledge base built directly by domain experts (OLDS). Among these systems, OMES are considered to be superior to other systems in terms of performances, development costs, and practicalness. In this paper, we present our methods, and describe our experimental and comparison results.

We apply Fahlman and Lebiere's (FL) algorithm to network synthesis and incremental learning by making use of already-trained networks, each performing a specified task, to design a system that performs a global or extended task without destroying the information gained by the previously trained nets. Investigation shows that the synthesized or expanded FL networks have generalization ability superior to Back propagation (BP) networks in which the number of newly added hidden units must be pre-specified.

The erosion of contact metal, which determines the life of contacts in the telephone switching system, is proportional to the arc energy. The equations for arc voltage, arc current, arc duration time and number of arcs are expressed explicitly in terms of circuit parameters and contact properties, and the expression is derived for arc energy that accompanies a single operation of contact closure. Contact erosion is consistent with the calculated arc energy. The erosion rate at closure is estimated based on the measured contact-erosion volume and the calculated arc energy. Arc energy at contact closure becomes as large as that at contact break if the cable is long or the supply voltage is high. This expression in combination with the expression for contact break enabled us to perform contact life design, which is indispensable for maintenance administration of telephone switching systems.

This paper theoretically evaluates the external electro-optic (EO) sampling of high-speed electrical signals using poled polymers as materials for a proximity electric-field sensor. Based on the derivation of the half-wave voltage and the analysis of a static electric field coupled to the polymeric media placed over IC interconnections, invasiveness, voltage sensitivity, and spatial resolution have been discussed. The polymeric sensors have shown to be used in contact with the IC interconnections with negligibly small invasiveness, thus making polymeric sensors provide higher sensitivity and spatial resolution than inorganic crystals such as GaAs and KD*P.

Reactive gases such air pollution agents as H2S or SO2 usually corrode the electrical contact surfaces. Since corrosion products formed on the surface increase contact resistance, they harmfully degrades contact reliability. To prevent the corrosion of the surface, oil coating on it may be effective. The oil film acts basically as a barrier for reaction between the corrosive gas and the surface. For thin film coating, the corrosion inhibition can not be expected. However, effect of film thickness on the corrosion property has not been clarified. In the present study, in order to clarify the corrosion inhibition of the oil coating for the contacts, the stearic acid coating on Ag (silver) contact surface was studied from view-point of the relationship between the thickness of the coating film and the contact resistance. As results, the effect of the stearic acid coating on corrosion inhibition in the atmosphere contained with H2S 3 ppm was found. However, the corrosion of the surface coated with thin stearic acid film occurred at microscopically scattered thin patiches in the specific pattern of the film. Existing of the optimum thickness of the stearic acid coating which gives both minimum contact resistance and effective corrosion inhibition was found. In the intermediate film thickness, this optimum thickness was induced by the increased contact resistance due to corrosion of the thin film region and insulation property of the stearic acid in the thick film region. Moreovr,it was found that this optimum thickness was affected by corrosion time. At the early stage of corrosion, the optimum thickness was about 200 . However, the corrosion time becomes longer as 700 min, this optimum thickness changed to thick as 1000 . With this increase in the thickness, the contact resistance in the optimum thickness rised to high level. Furthermore, the contact resistance in the optimum thickness decreased with increase in the contact load. However, dependence of the contact load on the optimum thickness was not recognized under a certain corrosion time.

This paper reports the influence of optical reflection induced noise and distortion for optical fiber feeder systems for microcellular mobile communication systems. Since the optical feeder requires very wide dynamic range, noise and distortion must be suppressed to an extremely low level. From optical transmission experiments and theoretical analysis, the basic characteristics of the reflection induced noise and distortion were investigated. By using these results, it was estimated that, for currently used analog mobile telephone systems, the number of connectors with 35 dB reflectance must be limited to less than 17, in order to suppress the noise caused by the connector reflections. Moreover, it was confirmed that the reflection induced distortion drastically decreases according to the increase of the length between reflectors. Therefore, the distortion can be suppressed by expanding the connector spacing to more than 7 meters.

This paper describes a new supervised speaker adaptation method based on vector field smoothing, for small size adaptation data. This method assumes that the correspondence of feature vectors between speakers can be viewed as a kind of smooth vector field, and interpolation and smoothing of the correspondence are introduced into the adaptation process for higher adaptation performance with small size data. The proposed adaptation method was applied to discrete HMM based speech recognition and evaluated in Japanese phoneme and phrase recognition experiments. Using 10 words as the adaptation data, the proposed method produced almost the same results as the conventional codebook mapping method with 25 words. These experiments clearly comfirmed the effectiveness of the proposed method.

This paper proposes the laser diode receiving mixer which utilizes the laser diode nonlinearity. The laser diode receiving mixer can make the bidirectional fiber optic link simple and cost-effective. These laser diodes are applied to configure the LD-LD MIX link which consists of two laser diodes, two local oscillators, two microwave switches and one fiber cable. The LD-LD MIX link configuration is extended to introduce novel two fiber optic links, i.e. the local suppression link and the image cancellation link. These links utilize the combination of microwave circuits and optical devices. These configurations are experimentally investigated at microwave frequencies and the QPSK signal transmission is successfully demonstrated.