In order to provide a low profile wire antenna for mobile communication, we have developed a new type of the transmission line type antenna, which we call a Modified Transmission Line Antenna (MTLA). Analysis of a certain type of the modified transmission line antenna has revealed that the input impedance and the gain can be determined independently by appropriately choosing antenna configuration. In this paper, we first explain the fundamental characteristics of the modified transmission line antenna. We then introduce two types of MTLA, i. e. a zigzag MTLA and a double MTLA, for practical application of the MTLA to mobile communication. Their characteristics are also discussed theoretically and experimentally.

A 1/2 frequency divider using resonant-tunneling hot electron transistors (RHETs) has been proposed and demonstrated. The circuit make the best use of negative differential conductance, a feature of RHETs, and contains one half transistors than used in conventional circuits. The RHETs were fabricated using self-aligned InGaAs RHETs and WSiN thin-film resistors on a single chip. The RHETs have an i-InGaAlAs/i-InGaAs collector barrier that improves the current gain at low collector-base voltages. Circuit operation was confirmed at 77 K.

The transmission of 8-bit µ-law PCM signals using 16-level weighted QAM over Gaussian channels is examined. The weighting process modifies the positions of the QAM constellation points so that the overall distortion in the recovered information-bearing source signal is reduced. The PCM bits are mapped to the weighted QAM points such that the most significant bits have a lower probability of being in error than the least significant bits. The weighted QAM systems have been optimized for the same energy signal energy per transmitted symbol as for unweighted QAM. Also, the erasure zone is established at the detector, such that if the output falls into the erasure zone, the regenerated sample is replaced by interpolation. The theoretical results indicates that 16-level weighted QAM have a gain of 5dB over unweighted QAM.

The DSD (Double Soft Decision) concatenated forward error correction scheme is proposed to realize a higher-coding-gain forward error correction system with simple hardware. The novel scheme soft decision decodes inner codes as well as outer codes. In this scheme, likelihood information from an inner Viterbi decoder is used for the decoding of outer codes. Path memory circuit status 1,0 ratio is newly proposed as a measure of likelihood information and it is shown that this method is the most reliable even though it has the simplest hardware among the alternative likelihood information extracting methods. Computer simulation clarifies that the proposed DSD scheme improves Pe performance to one-third that of the conventional hard decision outer decoding.

This paper proposes a next-generation narrow-band ISDN (N-ISDN), including a suitable network and network node architecture. The proposed N-ISDN allows every subscriber to use H0/HI-class calls as easily as present telephone calls, and could rapidly expand ISDN services to all the subscribers of a public network. The present status of ISDN is first analyzed then the need for popularization of H0/HI-call services is discussed. The proposed key technologies to popularize HO/HI services are (1) on-chip integration of ISDN switching systems, (2) distribution of small on-chip switching systems over the subscriber switching area, (3) H0-based trunk circuit networks using H0 on-chip switching systems and (4) efficient and flexible call management for 64-kb/s basic-class calls. An estimation of hardware volume of switching nodes is used to show that the proposed architecture is more economical than other possible alternatives, i.e. conventional ISDN and B-ISDN.

As the size and complexity of network increases, the distributed systems management (DSM) will be vital in order to improve the availability of network management, to reduce the complexity of network operations, and to provide the high reliability. In this paper, we (1) describe general requirements required for systems management in distributed environment, (2) introduce the basic structure of distributed network management system (DNMS) for efficient network management, and also especially illustrate the concrete design of system management application process which is an important element among them, (3) propose the connectionless CMIP to accomplish for effectively managing the distributed management system, and indicate its efficiency; this protocol is available to manage dynamically changing DSM environment, to negotiate among the managing systems, to handle the dynamic informations etc. Finally, (4) the behavior and software structure of a suggested management system during negotiation to execute the received request for implementation are presented.

It often occurs in an environmental phenomenon in our daily life that a specific signal is partially or completely contaminated by the additional external noise. In this study, a digital filter for estimating a specific signal fluctuating impulsively under the existence of an actual external noise with various kinds of probability distribution forms is proposed in an improved form of already reported digital filter. The effectivenss of the proposed theory is experimentally confirmed by applying it to the estimation of an actual impulsve signal in a room acoustic.

Generalized telegraphist's equations for waveguides are frequently used for analyzing fields in tapered rectangular waveguides. However, the telegraphist's equations do not give exact fields in E-plane tapers of the rectangular waveguides. In this letter, the new telegraphist's equations are shown, and the equations give the fields which exactly satisfy Maxwell's equations and the boundary conditions for the E-plane taper of the waveguide.

This paper describes on the transmission properties of the superconducting coplanar waveguide on LiNbO3 (LN) substrates, fabricated by YBa2Cu3Oy (YBCO) superconducting films. The films have been prepared by the reactive co-evaporation method and patterned by a wet etching process. The surface resistance of the obtained film was 0.04 Ω at 18 GHz and 77 K. It was confirmed from X-ray diffraction (XRD) that these films were highly oriented to the direction of c-axis without a secondary phase. The microwave transmission properties of these YBCO coplanar waveguides were investigated at frequencies up to 20 GHz and compared with that of the aluminum coplanar waveguide. The characteristic impedances of both coplanar waveguides were designed to be 50 Ω. It was found that the attenuation constants of these samples at 77 K were less than that of the aluminum coplanar waveguide for frequencies below 18 GHz.

A Chebyshev type bandpass filter using four TM01δ-mode dielectric rod resonators oriented axially in a high-Tc superconductor cylinder is designed with 3 dB bandwidth 36 MHz at 11.958 GHz. The single resonator which contains a Ba (MgTa) O3 ceramic rod of εγ=24 and a YBa2Cu3Oy bulk cylinder is designed to realize temperature coefficient of f0, τf=0 ppm/K at 20 K. The unloaded Q, Qu measured at 20 K is 150,000 which is higher than Qu=100,000 for a TM01δ-mode resonator with a copper cylinder. When the constructed filter is cooled from room temperature to below 50 K, the center frequency shifted only 5 MHz which corresponds to τf=1.5 ppm/K and the insertion loss IL0 at the center freqency reduced from 3.0 dB to about 0 dB, the designed value of which is 0.04 dB, which is too small to be measured accurately.

Experimental results on the superconducting three-terminal devices Using Bi-system High-Tc Superconductors were reported. The VCJJ (Variabel critical-current-type Josephson junction devices) using the thermal effect (VCJJ) and a dual gate Josephson device of a new current-injection type are described. The basic technology and problems for high-Tc three-terminal devices are briefly discussed.

The authors design a simple feed system for a planar slotted waveguide array. A waveguide π-junction with negligible reflection is cascaded to compose a multiple-way power divider. The frequency characteristics of the power divided to each port and the reflection at the feed point are discussed and high performances are predicted. The maximum number of cascaded junctions in this system can be determined in terms of a desired frequency bandwidth and allowable deviation in divided power.

In this paper the three dimensional (3-D) effect on CMOS latch-up is modeled using a graphical technique based on the fundamental principle of "charge neutrality or its current continuity equivalent" in the base region of parasitic transistors involved in latch-up. The graphical generation of the complete latch-up I-V characteristic requires as an input the SPICE parameters of the relevant bipolar and MOS transistors, the values of shunt resistances and the reverse current-voltage characteristic of the well-substrate junction. The infiuence of the MOS transistor shunting the parasitic bipolar transistors has received special attention. The nonideal scaling of the parasitic resistances has been observed to be the most crucial parameter determining the 3-D nature of the device. The proposed model is validated with test-structures fabricated in 2 µm bulk CMOS technology at and above room temperature. SAFE space map is constructed with width W as a parameter.

In this paper we examine the architectural and operational design issues of a practical network management system using the Simple Network Management Protocol (SNMP) in the context of a large-scale OSI-based campus-network TAINS. Various design aspects are examined and the importance of time-management is elicited. In the proposed design, intelligent, time-synchronised agents are deployed to collect information about the network segments to which they are attached. The manager talks to the agents and gathers relevant network information. This information is used by the expert network manager, in conjunction with a network knowledge base (NKB) and a management information knowledge base (MIKB) , to reconstruct the overall network-traffic characteristic, to evaluate the status of the network and to take/suggest some action. This model is particularly useful in networks where some global control, monitoring and management is desired and installing agents on all elements, connected to the network, is impossible. The use of time labels and narrow time windows enables the manager to obtain a reasonably accurate picture of the network status. The introduction of time-labelled composite objects in the Management Information Base (MIB) provides a means of reducing the load of management-related traffic on the network. The MIKB containing a logical description of the behaviour of the managed objects defined in the MIB, drives the expert system and provides the knowledge of general nature that a human expert has about networks. The proposed MIKB concept provides a very convenient schema for building the knowledge base in an expert network management system. Further since the MIKB is MIB-specific, it can be used in network management systems for managing similar MIB's.

This paper proposes an efficient design method of three-dimensional (3-D) recursive digital filters for video signal processing via decomposition of magnitude specifications. A given magnitude specification of a 3-D digital filter is decomposed into specifications of 1-D digital filters with three different (horizontal, vertical, and temporal) directions. This decomposition can reduce design problems of 3-D digital filters to design problems of 1-D digital filters, which can be designed with ease by conventional methods. Consequently, design of 3-D digital filters can be efficiently performed without complicated tests for stability and large amount of computations. In order to process video signal in real time, the 1-D digital filters with temporal direction must be causal, which is not the case in horizontal and vertical directions. Since the proposed method can approximate negative magnitude specifications obtained by the decomposition with causal 1-D R filters, the 1-D digital filters with temporal direction can be causal. Therefore the 3-D digital filters designed by the proposed method is suitable for real time video signal processing. The designed 3-D digital filters have a parallel separable structure having high parallelism, regularity and modularity, and thus is suitable for high-speed VLSI implementation.

Based on the Fornasini-Marchesini second model, an efficient algorithm is developed to derive the characteristic polynomial and the inverse of the system matrix from the state-space parameters. As a result, the external description of the Fornasini-Marchesini second model is clarified. A technique for designing 2-D recursive digital filters in the frequency domain is then presented by using the Fornasini-Marchesini second model. The resulting filter approximates both magnitude and group delay specifications and its stability is always guaranteed. Finally, three design examples are given to illustrate the utility of the proposed technique.

An integrated multiplexer in intermediate node is analyzed. The multiplexer is modeled as a system with multiple synchronous servers (channels) and having two kinds of customers. Between the two, one is wideband (WB) and the other is narrowband (NB); they are queueable with the same deterministic service time. The WB customer is given higher priority of channel access than the NB. To incorporate the delay constraint of WB, we use a simple instant discarding scheme for WB. As a result, the system states defined just after the beginning of a slot form an one-dimensional embedded Markov chain. This makes the analysis computationally tractable. The performance measures such as queue length distribution, average blocking probability, and average waiting time are obtained, particularly, the waiting time distribution. Some interesting numerical examples are discussed. Simulation results are also provided to help verify the validity of analysis.

The two most important parameters in reactive ion etching process, ion bombardment energy and flux, were extracted through a simple RF waveform measurement at the excitation electrode in a conventional cathode-coupled plasma RIE system. By using the extracted plasma parameters, damage and contamination in Si substrates induced by reactive ion etching in a SiCl4 plasma were investigated. A very convenient map representation of ion energy and ion flux was introduced in understanding the etching process occurring in the RIE system.

A formula for the variations in vertex-potentials caused by an increase of an edge-weight is derived using topological methods. This formula can be expressed in terms of the increase of the weight and the potential differences between two vertices joined by the edge with respect to three ordered vertex-pairs in the original network before the weight is increased.

In this paper, we present an automatic implementation method by which executable communication programs in C can be generated from protocol specifications in LOTOS. The implementation method consists of two parts: 1) An implementation strategy and 2) a set of translation rules. The first part consists of the basic ideas on how to realize the primary mechanisms in LOTOS specifications. The second part formulates the implementation method by way of the translation rules based on the implementation strategy. The characteristics of our method can be summarized as follows: We formulate our implementation method by way of translation rules. These rules are defined topdown in the form of syntax-directed translation function. The mechanism for controlling concurrency and communication among the user processes corresponding to the processes in LOTOS specification is easily realized by using UNIX operating system functions. The translation rules have been implemented on the AS 3000 (SUN3) workstation. An application of this implementation method is demonstrated by a simplified token-ring-protocol.