In this paper, the performance of multi-stage parallel interference cancellation receiver using forward-backward filtering channel estimation is evaluated for the W-CDMA uplink. The channel estimation employs a non-causal forward-backward-multiplication-method filter, which was originally proposed for the reception of W-CDMA random access. Results of link level simulations for data and voice traffic scenarios over Pedestrian A and Vehicular A channels are discussed in comparison with the conventional channel estimation methods of 1-slot pilot averaging, 1-slot averaging, and weighted multiple slot averaging. It is shown that the forward-backward filtering channel estimation improves performances of the interference cancellation receiver as well as that of the ordinary Rake receiver in both Pedestrian A and Vehicular A channels. With its features of short processing delay and low complexity, the forward-backward filtering channel estimation is suitable for practical implementations of multi-stage interference cancellation receivers.

During TCP/IP communications, MobileIP routing optimization functions causes out-of-order TCP packet sequences. To solve this problem, we propose a dynamic delayed ACK control scheme in which the wireless link-state management part notifies the upper TCP/IP layer of base-station hand-over, and at this time the TCP/IP layer sends dynamic delayed ACKs in response by using two-level-timer (i.e., hard-timer and soft-timer) processing. Simulation results confirm that applying dynamic delayed ACK control to MobileIP networks improves average throughput.

A performance comparison is developed between a chaotic communication system and a spread spectrum system with similar features in terms of bandwidth and transceiver structure but based on more conventional Gold sequences. Comparison is made in the presence of noise and multipath contributions which degrade the channel quality. It is shown that, because of its more favourable correlation properties, the chaotic scheme exhibits lower error rates, at a parity of the bandwidth expansion factor. The same favourable correlation properties are also used to explain and show, through a numerical example, the benefits of chaotic segments in a multi-user environment.

As two simple relaxation oscillators are coupled by periodical and instantaneous switching, the system exhibits rich superstable synchronous phenomena. In order to analyze the phenomena, we derive a hybrid return map of real and binary variables; and give theoretical results for (1) superstability of the synchronous phenomena and (2) period of the synchronous phenomena as a function of the parameters. Using a simple test circuit, typical phenomena are verified in the laboratory.

We present a method to track and recognize shape-changing hand gestures simultaneously. The switching linear model using active contour model well corresponds to temporal shapes and motions of hands. However, inference in the switching linear model is computationally intractable, and therefore the learning process cannot be performed via the exact EM (Expectation Maximization) algorithm. Thus, we present an approximate EM algorithm using a collapsing method in which some Gaussians are merged into a single Gaussian. Tracking is performed through the forward algorithm based on Kalman filtering and the collapsing method. We also present a regularized smoothing, which plays a role of reducing jump changes between the training sequences of shape vectors representing complex-variable hand shapes. The recognition process is performed by the selection of a model with the maximum likelihood from some trained models while tracking is being performed. Experiments for several shape-changing hand gestures are demonstrated.

It is very important to accurately and effectively track the movement of each mobile terminal in the personal communications networks. Accordingly, various dynamic location update schemes reflecting the mobile terminal's moving pattern are proposed in the literature. Important schemes include time-based, movement-based, distance-based, and direction-based location update schemes. In this paper, we intend to improve the performance of the movement-based location update scheme which is simple to implement and shows good performance. The proposed location update scheme reflects each mobile terminal's movement characteristics and reduces the number of unnecessary location updates. The performance of the proposed scheme is evaluated and compared with the previously proposed movement-based location update scheme through simulation. The proposed location update scheme requires three memory elements to maintain the movement history in the mobile terminal. The simulation results show that the location management cost is significantly reduced especially for the case with small call-to-mobility ratio by minimizing the unnecessary location updates intrinsic in the movement-based location update scheme.

Low-profile inverter power supplies are increasingly required for backlight systems of liquid crystal displays (LCDs). A great deal of attention has been focused on the application of piezoelectric transformers (PTs) to such power supplies. To miniaturize PT inverters still further, PTs need to have sufficient high voltage-step-up-ratio, which can be achieved by a multilayered PT. First, this paper describes a method for simulating such performance using a distributed constant equivalent circuit model. The results of the simulation for a multilayered PT operated in the third order longitudinal vibration mode show that the resistance of internal electrodes causes the dominant loss factor. Next, a power inverter incorporating the multilayered PT was fabricated. This power inverter can be operated over a wide input DC voltage range from 7-20 V. Regarding a conventional inverter drive circuit, when input DC voltage range was extended, the inverter efficiency remarkably decreased. For the reason, we developed a new inverter circuit, which is equipped with an automatic drive voltage control circuit to maintain the drive voltage to the PT at a constant value. As a result, the fabricated power inverter exhibited more than 90% overall efficiency and 3.5 W output power, which is enough to light up a 12.1-inch color LCD. The maximum luminance efficiency on a light transmission plate of the backlight was as high as 30 cd/m2/W.

The transient phenomenon of electromagnetic waves caused by a time dependent resistive screen in a waveguide is treated by using Wiener-Hopf technique. A boundary-value problem is formulated to describe the phenomenon, in which the resistivity of screen varies from infinite to zero in dependence on time. Application of the Fourier transformation with respect to time derives a Wiener-Hopf equation, which is solved by a commonly known decomposition procedure. The transient field is derived from the solution of the equation in terms of the Fourier inverse transform. By using the incomplete Lipschitz-Hankel integral for the computation of the field, numerical examples are given and the transient phenomenon is discussed.

We present an efficient scheme for progressive fractal coding in a wavelet multiresolution pyramid. In our proposed scheme, range blocks are selectively coded, based on energy localization in wavelet bands. In order to form domain pools with blocks yielding less distortion, domain blocks are also selectively searched in the wavelet bands of either the same or a different orientation from that of each range block at the next lower resolution. It is shown that the performance of the non-hybrid fractal coder presented is much better than that of predictive pyramid coding (PPC).

This paper proposes an operation-region model for analyzing and testing analog and mixed-signal circuits, which is based on observation of change in MOSFET operation regions. First, the relation between the change in MOSFET operation regions and the fault behavior of a mixed-signal circuit containing a bridging fault is investigated. Next, we propose an analysis procedure based on the operation-region model and apply it to generate the optimal input combination for testing the circuit. We also determine which transistors should be observed in order to estimate the circuit behavior. Since the operation-region model is a method for modeling circuit behavior abstractly, the proposed method will be useful for modeling circuit behavior and for analyzing and testing many kinds of analog and mixed-signal circuits.

A debug system for heterogeneous multiple processors in a single chip has been developed. The system consists of the debug interface circuit integrated on the chip, the interface circuit board between the chip and PC, and the debug software implemented on a PC. This debug system has been designed for a multimedia communication processor, which includes an original video processor core, a RISC processor, and a DSP. The RISC processor controls the Video Processing Unit that includes an original video processor and other hardware functions. While in debug mode, the external debugger can control the Video Processing Unit in the same manner as the RISC processor. The JTAG based interface circuit contains registers for bus transaction for command, address, and data to be written, etc. and a bus transaction sequencer. In fact, this system can realize the same bus transaction control as the RISC processor's. By applying proposed debug system, simultaneous debug of the RISC Processing Unit and the Video Processing Unit can be realized. This allows problems to be investigated more quickly and the total time required for debugging is efficiently reduced. Without this technology an estimated 19 weeks is required to debug the chip, whereas use of this technology allowed debugging to be completed in 9 weeks.

We investigated the suppression of multiuser interference in uplink multicarrier CDMA systems using the minimum mean squared error combining (MMSEC) method. In MMSEC, many pilot symbols are required to converge the weight vectors, and if we use just a few pilot symbols, the performance cannot be improved very much. We therefore developed a method for calculating weight vectors for MMSEC that uses just a few pilot symbols. The impulse responses of all users are first estimated using the pilot symbols in the time domain and modulated by a discrete Fourier transform. Next, the correlation matrices and correlation vectors are estimated from the impulse responses and the spreading codes of all users. Finally, the weight vectors that are obtained from the correlation matrices and correlation vectors are multiplied by the received signal to suppress the multiuser interference. The results of computer simulations indicated that the bit-error-ratio performance obtained using this method was better than that obtained when using the conventional fading compensation scheme or when using conventional MMSEC with the recursive least squares algorithm.

In this paper, we propose a new resource management scheme for multiple video stream transmission in a wireless environment. The proposed scheme adaptively determines transmission parameters such as the number of assigned time slots, modulation format, and forward error correction (FEC) code rate according to the required bit rate and error sensitivity of the video stream as well as the channel state. The computer simulation results show that the proposed scheme drastically improves the image quality degradation due to channel errors.

The EB tester line delay fault localization algorithm for combinational circuits is proposed where line delay fault probabilities are utilized to narrow fault candidates down to one efficiently. Probabilities for two main causes of line delay faults, defects of contact/vias along interconnections and crosstalk, are estimated through layout analysis. The algorithm was applied to 8 kinds of ISCAS'85 benchmark circuits to evaluate its performance where the guided probe (GP) diagnosis was used as the reference method. The proposed method can cut the number of probed lines to about 30% in average compared with those for the GP method. The total fault localization time was 31% of the time for the GP method and was 6% less than that of our previous method where the fault list generated in concurrent fault simulation is utilized.

This paper presents a method for disambiguating word senses in Korean-Japanese machine translation by using a language independent ontology. This ontology stores semantic constraints between concepts and other world knowledge, and enables a natural language processing system to resolve semantic ambiguities by making inferences with the concept network of the ontology. In order to acquire a language-independent and reasonably practical ontology in a limited time and with less manpower, we extend the existing Kadokawa thesaurus by inserting additional semantic relations into its hierarchy, which are classified as case relations and other semantic relations. The former can be obtained by converting valency information and case frames from previously-built electronic dictionaries used in machine translation. The latter can be acquired from concept co-occurrence information, which is extracted automatically from a corpus. In practical machine translation systems, our word sense disambiguation method achieved an improvement of average precision by 6.0% for Japanese analysis and by 9.2% for Korean analysis over the method without using an ontology.

In this paper, we have analyzed transmission time for WAP (Wireless Application Protocol) over Bluetooth using a multi-slot segmentation scheme. In order for SAR to improve the transfer capability, the transmission of messages have been simulated using a fragmentation scheme that begins with the total package and incremental fragmentation for each layer using the WTP (Wireless Transaction Protocol) to define the resultant packet size and the level of fragmentation for each proceeding layer. The data is divided into individual packets at the baseband level. This scheme decreases transmission time of L2CAP (Logical Link Control And Adaptation Protocol) baseband packets by sending packets that span multiple slots. From the results, we were able to obtain packet transmission time and optimal WTP packet size for WAP over Bluetooth in a Rician fading channel.

This paper presents an iterative algorithm for decoding product codes based on syndrome decoding of component codes. This algorithm is devised to achieve an effective trade-off between error performance and decoding complexity. A simplified list decoding algorithm, which uses a modified syndrome decoding method, for linear block codes is devised to deliver soft outputs for iterative decoding of product codes. By adjusting the size of the list, the decoder can achieve a proper trade-off between decoding complexity and performance. Compared to the other iterative decoding algorithms for product codes, the proposed algorithm has lower complexity while offers at least the same performance, which is demonstrated by analyses and simulations. The proposed algorithm has been simulated for BPSK and 16-QAM modulations over both the additive white Gaussian noise (AWGN) and Raleigh fading channels. This paper also presents an efficient scheme for applying product codes and their punctured versions. This scheme can be implemented with variable packet size and channel data block.

Recently, neural networks (NNs) have been extensively applied to many signal processing problem due to their robust abilities to form complex decision regions. In particular, neural networks add flexibility to the design of equalizers for digital communication systems. Recurrent neural network (RNN) is a kind of neural network with one or more feedback loops, whereas self-organizing map (SOM) is characterized by the formation of a topographic map of the input patterns in which the spatial locations (i.e., coordinates) of the neurons in the lattice are indicative of intrinsic statistical features contained in the input patterns. In this paper, we propose a novel receiver structure by combining adaptive RNN equalizer with a SOM detector under serious ISI and nonlinear distortion in QAM system. According to the theoretical analysis and computer simulation results, the performance of the proposed scheme is shown to be quite effective in channel equalization under nonlinear distortion.

This paper presents a comprehensive investigation of three optical wavelength-division multiplexed (WDM) mesh network protection approaches, namely minimal cost, single link basis and disjoint path approaches. The operation of each approach is described and their performances are extensively evaluated and compared. Key aspects that are taken into the consideration and comparison of the designs include a spare capacity requirement, ease of operation and practical feasibility. A mathematical model based on integer linear programming is introduced to obtain a lower bound on the spare capacity requirement for full protection against all single link failures. Two heuristic algorithms have also been developed to perform wavelength resource allocation under both normal and failure conditions for both systems with and without wavelength conversion capability. It is shown that the minimal cost approach can accomplish the lowest extra cost requirement for protection, but this approach is considered not appropriate for practical applications due to complicated restoration and management. The single link basis scheme is on the other hand more practical and very cost efficient. For the disjoint path technique, the cost for spare capacity is generally slightly greater than that of the single link basis scheme. Its main advantages lie in the simple re-configuration and inherent protection against node failure for in-transit traffic. Finally, a new framework for obtaining a good spare capacity cost estimate of a mesh restorable network is presented.

This paper presents the transmission performance of a class-IV partial-response signaling SSB system and proposes a method that can improve its power efficiency. A line code that has no dc component has been used in the SSB transmission of digital signals. The type of line code, such as a partial-response signaling, increases the modulation states, and as a result, decreases the power efficiency. To overcome this obstacle, a new demodulation method called "re-filtering and combining" is proposed on the assumption of orthogonal phase detection. The demodulated quadrature channel is re-filtered by a Hilbert filter and is combined with the in-phase channel. It is confirmed by computer simulations that the new demodulation method improves the BER performance and a 3 dB improvement of the power efficiency is obtained.