Phase interferometer using baseline composed by uniform linear array (ULA) with stable phase center for estimating the angle of arrival (AOA) is always employed in the direction finding (DF) system. However, the phase center of antenna element could vary with the incident angle, frequency, multipath and so on. To deal with these problems, a novel method is proposed in this paper to calibrate the phase center over ultra-wideband (UWB). Meanwhile, the restrictions of this method are discussed. Numerical simulations reveal that higher accuracy and larger unambiguous angle range can be obtained by the proposed method.
Bingzhou HONG Takuya KITANO Haisong JIANG Akio TAJIMA Kiichi HAMAMOTO
We newly propose the first lateral mode selective active multimode interferometer laser diode. The design principle is to arrange identical propagation path of different lateral mode. Thanks to multimode waveguide structure, 0th mode and 1st order mode has individual propagation path within one device. Individual lasing of fundamental mode as well as first mode was confirmed successfully.
Toshifumi KOBORI Norihiko KAMATA Takeshi FUKUDA
An optical intensity distribution under light irradiation in the organic photovoltaic cell affects the absorbance of the active layer, which determines the photovoltaic performance. In this research, we evaluated the optimum thickness of the organic active layer with poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b;4,5-b']dithiophene-2,6-diyl-alt-(4-(2-ethylhexyl)-3-fluorothieno[3,4-b]thiophene-)-2-carboxylate-2-6-diyl)] and [6,6]-phenyl C71-butyric acid methyl ester. The spectral response of external quantum efficiency was good agreement with the simulated optical intensity distribution within a device stack as a function of the position and the wavelength. As a result, the highest photoconversion efficiency of 10.1% was achieved for the inverted device structure.
Shota TAKEUCHI Kazuki SAKUMA Kazutoshi KATO Yasuyuki YOSHIMIZU Yu YASUDA Shintaro HISATAKE Tadao NAGATSUMA
For phase stabilization of two-tone coherent millimeter-wave/microwave carrier generation, two types of phase detection schemes were devised based on lightwave interferometric technique, the Mach-Zehnder interferometric method and the pseudo Mach-Zehnder interferometric method. The former system showed clear eye patterns at both OOK and PSK modulations of 1 Gbit/s on the 12.5-GHz carrier. The latter system demonstrated the error-free transmission at OOK modulation of 11 Gbit/s on the 100-GHz carrier.
Hiroki YAMAZAKI Takuya SAKAMOTO Hirofumi TAKI Toru SATO
Microwave systems have a number of promising applications in surveillance and monitoring systems. The main advantage of microwave systems is their ability to detect targets at distance under adverse conditions such as dim, smoky, and humid environments. Specifically, the wide bandwidth of ultra-wideband radar enables high range resolution. In a previous study, we proposed an accurate shape estimation algorithm for multiple targets using multiple ultra-wideband Doppler interferometers. However, this algorithm produces false image artifacts under conditions with severe interference. The present paper proposes a technique to suppress such false images by detecting inconsistent combinations of the radial velocity and time derivative of image positions. We study the performance of the proposed method through numerical simulations of a two-dimensional section of a moving human body, and demonstrate the remarkable performance of the proposed method in suppressing false image artifacts in many scenarios.
Dexiu HU Zhen HUANG Jianhua LU
This paper proposes and analyses an improved direction finding (DF) method that uses a rotating interferometer. The minimum sampling frequency is deduced in order to eliminate the phase ambiguity associated with a long baseline, the influence of phase imbalance of receiver is quantitatively discussed and the Root Mean Square Error (RMSE) of both bearing angle and pitch angle are also demonstrated. The theoretical analysis of the rotating interferometer is verified by simulation results, which show that it achieves better RMSE performance than the conventional method.
Akira ENOKIHARA Masashi YAMAMOTO Tadashi KAWAI Tetsuya KAWANISHI
An electro-optic (EO) modulator integrated with the microwave planar circuit directly formed on a LiNbO3 (LN) substrate for low frequency-chirp performance and compact configuration is introduced. Frequency chirp of EO intensity modulators was investigated and a dual-electrode Mach-Zehnder (MZ) modulator combined with a microwave rat-race (RR) circuit was considered for the low-chirp modulation. The RR circuit, which operates as a 180-degree hybrid, was designed on a z-cut LN substrate to create two modulation signals of the same amplitude in anti-phase with each other from a single input signal. Output ports of the RR were connected to the modulation electrodes on the substrate. The two signals of the equal amplitude drive two phase modulation parts of the modulator so that the symmetric interference are realized to obtain intensity modulation of low frequency-chirp. The modulator was designed and fabricated on a single LN substrate for around 10 GHz modulation frequencies and 1550 nm light wavelength. The chirp parameters were measured to be less than 0.2 in the frequency range between 8 and 12 GHz. By compensating imbalance of the light power splitting in the waveguide MZ interferometer the chirp could be reduced even more.
Mohammad NASIR UDDIN Takaaki KIZU Yasuhiro HINOKUMA Kazuhiro TANABE Akio TAJIMA Kazutoshi KATO Kiichi HAMAMOTO
Laser diode capable of high speed direct modulation is one of the key solution for short distance applications due to their low power consumption, low cost and small size features. Realization of high modulation bandwidth for direct modulated laser maintaining the above mentioned feature is needed to enhance the short distance, low cost data transmission. One promising approach to enhance the modulation speed is to increase the photon density to achieve high modulation bandwidth. So to achieve this target, 1.55 $mu$m InGaAsP/InGaAsP multiple quantum well (MQW) asymmetric active multimode interferometer laser diode (active MMI-LD) has been demonstrated [1]. The split pumping concept has been applied for the active MMI-LD and significant enhancement of electrical to optical 3 dB down frequency bandwidth (f$_{mathrm{3dB}})$ up to 8 GHz has been successfully confirmed. The reported high bandwidth for split pump active MMI-LD is around 3.5 times higher than the previously reported maximum 3 dB bandwidth (2.3 GHz) of active MMI-LD without split pumping section. That shows, the splitted multimode pumping section behind the electrically isolated modulation section can potentially improve the modulation bandwidth of active MMI-LD. Clear and open eye diagram had also been confirmed for 2.5 Gbps, (2$^{mathrm{7}}$-1) pseudo random bit sequence (PRBS) modulation.
Yu SUGITA Yoshifumi TAKASAKI Keiji KURODA Yuzo YOSHIKUNI
A Fourier domain optical coherence tomography system for obtaining a two-dimensional image is constructed. Imaging characteristics of the OCT system in a transverse direction are experimentally investigated. Angle dependence of reflection intensity from a smooth surface is clearly observed and analyzed with consideration of spatial mode coupling to a fiber.
Zhigang ZANG Keisuke MUKAI Paolo NAVARETTI Marcus DUELK Christian VELEZ Kiichi HAMAMOTO
The fabricated 1.55 µm high power superluminescent light emitting diodes (SLEDs) with 115 mW maximum output power and 3 dB bandwidth of 50 nm, using active multi-mode interferometer (MMI), showed high coupling efficiency of 66% into single-mode fiber, which resulted in maximum fiber-coupled power of 77 mW.
Wooram LEE Dongkyun KIM Kwanho YOU
In this paper a nonlinearity compensation algorithm based on the extended Kalman filter is proposed to improve the measurement accuracy of a heterodyne laser interferometer. The heterodyne laser interferometer is used for ultra-precision measurements such as those used in semiconductor manufacturing. However the periodical nonlinearity property caused by frequency-mixing restricts the accuracy of the nanometric measurements. In order to minimize the effect of the nonlinearity, the measurement process of the laser interferometer is modeled as a state equation and the extended Kalman filtering approach is applied to the process. The effectiveness of our proposed algorithm is demonstrated by comparing the results of the algorithm with experimental results for the laser system.
Yusuke NASU Yohei SAKAMAKI Kuninori HATTORI Shin KAMEI Toshikazu HASHIMOTO Takashi SAIDA Hiroshi TAKAHASHI Yasuyuki INOUE
We present a full description of a polarization-independent athermal differential quadrature phase shift keying (DQPSK) demodulator that employs silica-based planar lightwave circuit (PLC) technology. Silica-based PLC DQPSK demodulator has good characteristics including low polarization dependence, mass producibility, etc. However delay line interferometer (DLI) of demodulator had the large temperature dependence of its optical characteristics, so it required large power consumption to stabilize the chip temperature by the thermo-electric cooler (TEC). We previously made a quick report about an athermal DLI to reduce a power consumption by removing the TEC. In this paper, we focus on the details of the design and the fabrication method we used to achieve the athermal characteristics, and we describe the thermal stability of the signal demodulation and the reliability of our demodulator. We described two athermalization methods; the athermalization of the transmission spectrum and the athermalization of the polarization property. These methods were successfully demonstrated with keeping a high extinction ratio and a small footprint by introducing a novel interwoven DLI configuration. This configuration can also limit the degradation of the polarization dependent phase shift (PDf) to less than 1/10 that with the conventional configuration when the phase shifters on the waveguide are driven. We used our demodulator and examined its demodulation performance for a 43 Gbit/s DQPSK signal. We also verified its long-term reliability and thermal stability against the rapid temperature change. As a result, we confirmed that our athermal demodulator performed sufficiently well for use in DQPSK systems.
Tetsuya KAWANISHI Takahide SAKAMOTO Akito CHIBA
We present recent progress of high-speed Mach-Zehnder modulator technologies for advanced modulation formats. Multi-level quadrature amplitude modulation signal can be synthesized by using parallel Mach-Zehnder modulators. We can generate complicated multi-level optical signals from binary data streams, where binary modulated signals are vectorially summed in optical circuits. Frequency response of each Mach-Zehnder interferometer is also very important to achieve high-speed signals. We can enhance the bandwidth of the response, with thin substrate. 87 Gbaud modulation was demonstrated with a dual-parallel Mach-Zehnder modulator.
Ryoichi AKIMOTO Guangwei CONG Masanori NAGASE Teruo MOZUME Hidemi TSUCHIDA Toshifumi HASAMA Hiroshi ISHIKAWA
We demonstrated all-optical demultiplexing of 160-Gb/s signal to 40- and 80-Gb/s by a Mach-Zehnder Interferometric all-optical switch, where the picosecond cross-phase modulation (XPM) induced by intersubband excitation in InGaAs/AlAsSb coupled double quantum wells is utilized. A bi-directional pump configuration, i.e., two control pulses are injected from both sides of a waveguide chip simultaneously, increases a nonlinear phase shift twice in comparison with injection of single pump beam with forward- and backward direction. The bi-directional pump configuration is the effective way to avoid damaging waveguide facets in the case where high optical power of control pulse is necessary to be injected for optical gating at repetition rate of 40/80 GHz. Bit error rate (BER) measurements on 40-Gb/s demultiplexed signal show that the power penalty is decreased slightly for the bi-directional pump case in the BER range less than 10-6. The power penalty is 1.3 dB at BER of 10 - 9 for the bi-directional pump case, while it increases by 0.3-0.6 dB for single pump cases. A power penalty is influenced mainly by signal attenuation at "off" state due to the insufficient nonlinear phase shift, upper limit of which is constrained by the current low XPM efficiency of 0.1 rad/pJ and the damage threshold power of 100 mW in a waveguide facet.
Suresh M. NISSANKA Ken MISHINA Akihiro MARUTA Shunsuke MITANI Kazuyuki ISHIDA Katsuhiro SHIMIZU Tatsuo HATTA Ken-ichi KITAYAMA
All-optical wavelength conversion and modulation format conversion will be needed in the next generation high-speed optical communication networks. We have proposed and successfully demonstrated the error free operation of all-optical modulation format conversion from NRZ-OOK to RZ-BPSK using SOA based MZI wavelength converter. In this paper, we experimentally investigate the wavelength conversion characteristics of the proposed NRZ-OOK/RZ-BPSK modulation format converter. The results show that error free modulation format conversion is possible over the entire C band.
Yasunori MIYAZAKI Kazuhisa TAKAGI Keisuke MATSUMOTO Toshiharu MIYAHARA Tatsuo HATTA Satoshi NISHIKAWA Toshitaka AOYAGI Kuniaki MOTOSHIMA
The design aspects of the bulk InGaAsP semiconductor optical amplifier integrated Mach-Zehnder interferometer (SOA-MZI) optimized for 40 Gbps-NRZ all optical wavelength conversion are described. The dimensions of the SOA active waveguide have been optimized for fast gain recovery by maximizing the gain and adjusting the wavelength-converted NRZ waveforms. Submicron-width buried heterostructure (BH) SOA waveguides were fabricated successfully and showed little leakage current. The experimental wavelength-converted optical waveform agreed well to the numerical simulations, and mask-compliant 40 G-NRZ wavelength-converted waveform was obtained by the optimized SOA-MZI. 40 G-NRZ full C-band operation and polarization-insensitive operation of SOA-MZI were also achieved.
Shin ARAHIRA Hitoshi MURAI Yoh OGAWA
A nonlinear optical fiber loop mirror (NOLM) adapted for all-optical 2R operation at ultrahigh bit-rates was experimentally and theoretically investigated. The proposed NOLM was created by adding inline/external fiber polarizers and also an inline optical phase-bias compensator (OPBC) to a standard NOLM. A theoretical investigation revealed that the operation of the standard NOLM became unstable due to residual polarization crosstalk of the polarization-maintaining optical components making up the NOLM, and that it could be dramatically improved with the inline/external polarizers. The NOLM with the polarizers ensured stable switching operation with high switching-dynamic-range (>30 dB) against the change of the wavelength of the input clock pulses, and the change of the environment temperature. We also experimentally verified that the OPBC played a dramatic role to ensure excellent dynamic switching performance of the NOLM, and to achieve signal-Q-recovery of the regenerated signals. All optical 2R experiments at 40 Gb/s and 160 Gb/s were performed with the modified NOLM. Signal regeneration with improved extinction ratio and signal Q value was successfully demonstrated. Q-recovery to the input of the control pulses degraded with ASE noise accumulation was also successfully achieved.
Xueliang SONG Naoki FUTAKUCHI Daisuke MIYASHITA Foo Cheong YIT Yoshiaki NAKANO
We achieved first dynamic all-optical signal processing with a bandgap-engineered MZI SOA all-optical switch. The wide-gap Selective Area Growth (SAG) technique was used to provide multi-bandgap materials with a single step epitaxy. The maximum photoluminescence (PL) peak shift obtained between the active region and the passive region was 192 nm. The static current switching with the fabricated switch indicated a large carrier induced refractive index change; up to 14 π phase shift was obtained with 60 mA injection in the SOA. The carrier recovery time of the SOA for obtaining a phase shift of π was estimated to be 250-300 ps. A clear eye pattern was obtained in 2.5 Gbps all-optical wavelength conversion. This is the first all-optical wavelength conversion demonstration with a bandgap-engineered PIC with either selective area growth or quantum-well intermixing techniques.
Yoshiyasu UENO Morio TAKAHASHI Shigeru NAKAMURA Kouichi SUZUKI Takanori SHIMIZU Akio FURUKAWA Takemasa TAMANUKI Kazuo MORI Satoshi AE Tatsuya SASAKI Kazuhito TAJIMA
Control scheme for accurately optimizing (and also automatically stabilizing) the interferometer phase bias of Symmetric-Mach-Zehnder (SMZ)-type ultrafast all-optical switches is proposed. In this control scheme, a weak cw light is used as a supervisory input light and its spectral power ratio at the switch output is used as a bipolar error signal. Our experimental result at 168-Gb/s 16:1 demultiplexing with a hybrid-integrated SMZ switch indicates the feasibility and the sensitivity of this control scheme.
Hiroshi HIRAYAMA Toshiyuki YAKABE Yoshio KAMI
A Fourier-optics based imaging system for electromagnetic interference (EMI) sources is presented. It is necessary to decrease undesired emissions in order to meet EMI requirements. To investigate this problem, a visualization of electromagnetic (EM) emitting fields is very useful. In this paper, we propose a passive imaging system of EM emitting fields based on Fourier optics. Amplitude and phase values of diffracted fields on an entrance pupil are acquired by using a six-port interferometer. The measured EM fields are then processed on a computer, and an image is retrieved using an inverse Fresnel transform. Experiments are presented, which demonstrate the potential of the proposed method. The proposed system is useful not only in the field of electromagnetic compatibility (EMC), but also for scientific elucidation to discuss the optics and microwave theory of the same viewpoint.