In order to meet various requirements for the 5th generation mobile communication, a high SHF wideband massive-MIMO system has been widely studied which offers wide system bandwidth and high spectral efficiency. A hybrid beamforming configuration which combines analog beamforming by APAA (Active Phased Array Antenna) and digital MIMO signal processing is one of the promising approaches for reducing the complexity and power consumption of the high SHF wideband massive-MIMO system. In order to realize the hybrid beamforming configuration in high SHF band, small size, low power consumption and precise beam forming over the wide-band frequency range are strongly required for RF frontend which constitutes analog beam former. In this paper, a compact RF frontend module for high SHF wideband 5G small cell base station is proposed. This RF frontend module is prototyped. Various key components of the RF frontend module are fabricated in 15GHz band, and measured results show that high RF performances are able to meet the requirements of RF frontend.

In the 5G era, centralized mobility management raises the issue of traffic concentration on the mobility anchor. Distributed mobility management is expected to be a solution for this issue, as it moves mobility anchor functions to multiple edge routers. However, it incurs path stretch and redundant traffic on the backhaul links. Although these issues were not considered important in the 3G/4G era, they are expected to be a serious problem in the 5G era. In this paper, we design a routing-based mobility management mechanism to address the above problems. The mechanism integrates distributed routing with Bloom Filters and an anchor-less scheme where edge routers work as mobility anchors. Simulations show that the proposed mechanism achieves a good balance between redundant traffic on the backhaul links and routing overhead.

In order to tackle rapidly increasing traffic, dramatic performance enhancements in radio access technologies (RATs) are required for fifth-generation (5G) mobile communication system. In 5G, small/semi-macro cells using Massive MIMO (M-MIMO) with much wider bandwidth in higher frequency bands are overlaid on macro cell with existing frequency band. Moreover, high density deployment of small/semi-macro cell is expected to improve areal capacity. However, in low SHF band (below 6GHz), antenna array size of M-MIMO is large so that it cannot be installed on some environments. Therefore, to improve system throughput on various use cases in 5G, we have proposed distributed Massive MIMO (DM-MIMO). DM-MIMO coordinates lots of distributed transmission points (TPs) that are located in ultra-high density (UHD). Furthermore, DM-MIMO uses various numbers of antenna elements for each TP. In addition, DM-MIMO with UHD-TPs can create user-centric virtual cells corresponding to user mobility, and design of flexible antenna deployment for DM-MIMO is applicable to various use cases. Then, some key parameters such as the number of the distributed TPs, the number of antenna elements for each TP, and proper distance between TPs, should be determined. This paper presents such parameters for 5G DM-MIMO with flexible antenna deployment under fixed total transmission power and constant total number of antenna elements. Computer simulations show that DM-MIMO can achieve more than 1.9 times higher system throughput than an M-MIMO system using 128 antenna elements.

In this paper, we present the roles played by millimeter-waves in the realization of an Internet of Things (IoT) society. Millimeter-waves are becoming essential frequency resources, enabling ultra-high-speed wireless networks supporting massive data traffic and high-resolution sensor devices. Multiple antenna technologies such as phased arrays, sector antennas, and MIMO signal processing are key technologies for putting these into practical use. In this paper, various examples of integration of multi-antenna systems are shown, as well as demonstration on 60GHz-band millimeter-wave wireless access and 79GHz-band high-resolution radar. We also propose applications to ITS for an IoT society, combining millimeter-wave wireless access and radar sensors, and discuss technical issues to be solved in the future.

This paper presents outdoor field experimental results to clarify the 4-by-4 multiple-input multiple-output (MIMO) throughput performance when applying joint transmission (JT) and distributed MIMO to the 15-GHz frequency band in the downlink of a 5G cellular radio access system. Experimental results for JT in a 100m × 70m large-cell scenario show that throughput improvement of up to 10% is achieved in most of the area and the peak data rate is improved from 2.8Gbps to 3.7Gbps. Based on analysis of the reference signal received power (RSRP) and channel correlation, we find that the RSRP is improved in lower RSRP areas, and that the channel correlation is improved in higher RSRP areas. These improvements contribute to higher throughput performance. The advantage of distributed MIMO and JT are compared in a 20m × 20m small-cell scenario. The throughput improvement of 70% and throughput exceeding 5 Gbps were achieved when applying distributed MIMO due to the improvement in the channel correlation. When applying JT, the RSRP is improved; however the channel correlation is not. As a result, there is no improvement in the throughput performance in the area. Finally, the relationship between the transmission point (TP) allocation and the direction of user equipment (UE) antenna arrangement is investigated. Two TP positions at 90 and 180deg. from each other are shown to be advantageous in terms of the throughput performance with different direction of UE antenna arrangement. Thus, we conclude that JT and distributed MIMO are promising technologies for the 5G radio access system that can compensate for the propagation loss and channel correlation in high frequency bands.

Efficient use of heterogeneous wireless access networks is necessary to maximize the capacity of the 5G mobile communications system. The wireless local area networks (WLANs) are considered to be one of the key wireless access networks because of the proliferation of WLAN-capable mobile devices. However, throughput starvation can occur due to the well-known exposed/hidden terminal problem in carrier sense multiple access with collision avoidance (CSMA/CA) based channel access mechanism, and this problem is a critical issue with wireless LAN systems. This paper proposes two novel schemes to identify starved access points (APs) and user equipments (UEs) which throughputs are relatively low. One scheme identifies starved APs by observing the transmission delay of beacon signals periodically transmitted by APs. The other identifies starved UEs by using the miscaptured beacon signals ratio at UEs. Numerous computer simulations verify that that the schemes can identify starved APs and UEs having quite low throughput and are superior to the conventional graph-based identification scheme. In addition, AP and UE management with the proposed schemes has the potential to improve system throughput and reduce the number of low throughput UEs.

This paper presents beamforming and beam tracking techniques and downlink performance results from field experiments using a Proof-of-Concept (PoC) system. The PoC implements a 5G mobile radio access system in the millimeter wave band and utilizes beamforming and beam tracking techniques. These techniques are realized with a dielectric lens antenna fed by a switched antenna feeder array. The half-power beamwidth of the antenna is 3° corresponding to massive MIMO using approximately 1000 antenna elements. The system bandwidth is 1GHz and the center frequency is 73.5GHz. Adaptive modulation and coding using four modulation and coding schemes is implemented. The field experiment is conducted in the following small cell environments: a courtyard, a shopping mall and a street canyon. The majority of the test area is Line-Of-Sight (LOS) however the shopping mall course contains 69% Non-LOS (NLOS) conditions. The results show that the maximum throughput of over 2Gbps using rate 7/8 coded 16QAM modulation is achieved in 87%, 34% and 28% of each of the respective environments. The beam tracking achieves high availability of coverage and seamless mobility not only in LOS environments but also under NLOS conditions through the reflected paths.

In this paper, the recent advances in cooperative distributed antenna transmission (CDAT) are introduced for spatial diversity and multi-user spatial multiplexing in 5G mobile communications network. CDAT is an advanced version of the coordinated multi-point (CoMP) transmission. Space-time block coded transmit diversity (STBC-TD) for spatial diversity and minimum mean square error filtering combined with singular value decomposition (MMSE-SVD) for multi-user spatial multiplexing are described under the presence of co-channel interference from adjacent macro-cells. Blind selected mapping (blind SLM) which requires no side information transmission is introduced in order to suppress the increased peak-to-average signal power ratio (PAPR) of the transmit signals when CDAT is applied. Some computer simulation results are presented to confirm the effectiveness of CDAT techniques.

In this paper, we clarify the issues in a metropolitan environment involving overlying frequency bands with various bandwidths and propose a cell selection scheme that improves the communications quality based on user and network characteristics. Different frequency bands with various signal bandwidths will be overlaid on each other in forthcoming fifth-generation (5G) radio access networks. At the same time, services, applications or features of sets of user equipment (UEs) will become more diversified and the requirements for the quality of communications will become more varied. Moreover, in real environments, roads and buildings have irregular constructions. Especially in an urban or metropolitan environment, the complex architecture present in a metropolis directly affects radio propagation. Under these conditions, the communications quality is degraded because cell radio resources are depleted due to many UE connections and the mismatch between service requirements and cell capabilities. The proposed scheme prevents this degradation in communications quality. The effectiveness of the proposed scheme is evaluated in an ideal regular deployment and in a non-regular metropolitan environment based on computer simulations. Simulation results show that the average of the time for the proposed scheme from the start of transmission to the completion of reception at the UE is improved by approximately 40% compared to an existing cell selection scheme that is based on the Maximum Signal-to-Interference plus Noise power Ratio (SINR).

Massive multiple-input multiple-output (MIMO) technology is one of the key enablers in the fifth generation mobile communications (5G), in order to accommodate growing traffic demands and to utilize higher super high frequency (SHF) and extremely high frequency (EHF) bands. In the paper, we propose a novel transmit precoding named “nonlinear block multi-diagonalization (NL-BMD) precoding” for multiuser MIMO (MU-MIMO) downlink toward 5G. Our NL-BMD precoding strategy is composed of two essential techniques: block multi-diagonalization (BMD) and adjacent inter-user interference pre-cancellation (IUI-PC). First, as an extension of the conventional block diagonalization (BD) method, the linear BMD precoder for the desired user is computed to incorporate a predetermined number of interfering users, in order to ensure extra degrees of freedom at the transmit array even after null steering. Additionally, adjacent IUI-PC, as a nonlinear operation, is introduced to manage the residual interference partially allowed in BMD computation, with effectively-reduced numerical complexity. It is revealed through computer simulations that the proposed NL-BMD precoding yields up to 67% performance improvement in average sum-rate spectral efficiency and enables large-capacity transmission regardless of the user distribution, compared with the conventional BD precoding.

This paper presents indoor and outdoor experiments that confirm 4-Gbps throughput based on 400-MHz bandwidth transmission when applying carrier aggregation (CA) with 4 component carriers (CCs) and 4-by-4 single-user multiple-in multiple-out multiplexing (MIMO) in the 15-GHz frequency band in the downlink of 5G cellular radio access. A new radio interface with time division duplexing (TDD) and radio access based on orthogonal frequency-division multiple access (OFDMA) is implemented in a 5G testbed to confirm ultra-high speed transmission with low latency. The indoor experiment in an entrance hall shows that the peak throughput is 4.3Gbps in front of the base station (BS) antenna where the reference signal received power (RSRP) is -40dBm although the channel correlation at user equipment (UE) antenna is 0.8. The outdoor experiment in an open-space parking area shows that the peak throughput is 2.8Gbps in front of a BS antenna with a high RSRP although rank 2 is selected due to the high channel correlation. The results also show that the average throughput of 2Gbps is achieved 120m from the BS antenna. In a courtyard enclosed by building walls, 3.6Gbps is achieved in an outdoor-to-outdoor environment with a high RSRP and in an outdoor-to-indoor environment where the RSRP is lower due to the penetration loss of glass windows, but the multipath rich environment contributes to realizing the low channel correlation.

Massive multiple input multiple output (MIMO) communication system offers high rate transmission and/or support of a large number of users by invoking the power of a large array antenna, but one of its problem is the heavy computational burden required for the design and signal processing. Assuming the utilization of a large array in the transmitter side and much fewer users than the maximum possible value, this paper first presents a subarray based design approach of MIMO system with a low computational load taking into account efficient subarray grouping for the realization of higher performance; a large transmit array is first divided into subarrays based on channel gain or channel correlation, then block diagonalization is applied to each of them, and finally a large array weight is reconstructed by maximal ratio combining (MRC). In addition, the extension of the proposed method to two-stage design is studied in order to support a larger number of users; in the process of reconstruction to a large array, subarrays are again divided into groups, and block diagonalization is applied to those subarray groups. Through computer simulations, it is shown that the both channel gain and correlation based grouping strategies are effective under certain conditions, and that the number of supported users can be increased by two-stage design if certain level of performance degradation is acceptable.

This paper discusses key technologies specific for fifth generation (5G) cellular systems which are expected to connect internet of things (IoT) based vertical sectors. Because services for 5G will be expanded drastically, from information transfer services to mission critical and massive connection IoT connection services for vertical sectors, and requirement for cellular systems becomes quite different compared to that of fourth generation (4G) systems, after explanation for the service and technical trends for 5G, key wireless access technologies will be discussed, especially, from the view point of what is new and how import. In addition to the introduction of new technologies for wireless access, flexibility of networking is also discussed because it can cope with QoS support services, especially to cope with end-to-end latency constraint conditions. Therefore, this paper also discuss flexible network configuration using mobile edge computing (MEC) based on software defined network (SDN) and network slicing.

In order to support user data rates of Gbps and above in the fifth generation (5G) communication systems, millimeter wave (mm-wave) communication is proposed as one of the most important enabling technologies. In this paper, we consider the spectrum bands shared by 5G cellular base stations (BS) and some existing networks, such as WiGig and proposed a method for spectrally efficient coexistence of multiple interfering BSs through adaptive self-organized beam scheduling. These BSs might use multiple radio access technologies belonging to multiple operators and are deployed in the unlicensed bands, such as 60GHz. Different from the recently emerging coexistence scenarios in the unlicensed 5GHz band, where the proposed methods are based on omni-directional transmission, beamforming needs to be employed in mm-wave bands to combat the high path loss problem. The proposed method is concerned with this new scenario of communication in the unlicensed bands where (a) beam-forming is mandatory to combat severe path loss, (b) without optimal scheduling of beams mutual interference could be severe due to the possibility of beam-collisions, (c) unlike LTE which users time-frequency resource blocks, a new resource, i.e., the beam direction, is used as mandatory feature. We propose in this paper a novel multi-RAT coexistence mechanism where neighbouring 5G BSs, each serving their own associated users, schedule their beam configurations in a self-organized manner such that their own utility function, e.g. spectral efficiency, is maximized. The problem is formulated as a combinatorial optimization problem and it is shown via simulations that our proposed distributed algorithms yield a comparable spectral efficiency for the entire networks as that using an exhaustive search, which requires global coordination among coexisting RATs and also has a much higher algorithmic complexity.

This paper presents some results of an experimental trial for the 5th generation (5G) wireless communication systems using 28GHz band. In order to tackle rapidly increasing traffic for 2020 and beyond, new radio access networks for the 5G mobile communication systems will introduce the use of higher frequency bands such as spectra higher than 10GHz to achieve higher capacity and super high bit rate transmission of several tens of Gbps. The target of this experimental trial is to evaluate the feasibility of using the 28GHz band with super-wide bandwidth of 800MHz for 5G wireless communication systems. To compensate large path-loss in higher frequency, the beamforming (BF) based on Massive multiple-input multiple-output (MIMO) is one of promising techniques and can be combined with spatial multiplexing of multiple data streams to achieve much higher capacity. In addition, to support the mobility of mobile station (MS), beam tracking technique is important. In this trial, we first conduct a basic experiment of single-stream transmission by using prototype system with base station (BS) having 96-element antenna and MS having 8-element antenna to evaluate the effectiveness of joint transmitter/receiver BF in 28GHz band in terms of coverage, impact of path loss, shadowing loss and penetration loss under indoor, outdoor and outdoor-to-indoor (O-to-I) environments. We show that by using 28 GHz band with BF based on Massive MIMO, higher throughput near 1.2Gbps can be achieved at many points in the indoor environment. It is also shown that the throughput of over 1Gbps can be achieved at points around 200m distant from BS in outdoor line-of-site (LOS) environment. Secondly, to evaluate the effectiveness of spatial multiplexing and beam tracking under more realistic environment, we also conduct the outdoor experiment of BF combined with 2-stream spatial multiplexing in high mobility environment with MS speed of up to 60km/h by using smartphone-shape MS antenna. We also show that maximum throughput of 3.77Gbps can be achieved with MS speed of 60km/h by using BF with 2-stream multiplexing and beam tracking.

As the most compelling candidate for 5G, millimeter-wave communication has drawn considerable interest, despite the absence of systematic research on its performance. Therefore, this study investigates millimeter-wave cellular networks and their use of existing frequency reuse schemes and scheduling methods. To evaluate the performance of these networks, we configure a system-level simulator that reflects the eNodeB architecture and frame structure designed to overcome the millimeter-wave frequency characteristics of the Giga Korea Project. Simulations conducted using various combinations of frequency reuse schemes and scheduling methods are described. We found that the best performing radio resource management scheme changes according to the number of user equipment accessing the eNodeB. The results of this study will contribute to performance estimations of the capacity and fairness of cellular-based millimeter-wave communication systems before they are deployed.

Hybrid analog/digital precoding has attracted growing attention for millimeter wave (mmWave) communications, since it can support multi-stream data transmission with limited hardware cost. A main challenge in implementing hybrid precoding is that the channels will exhibit frequency-selective fading due to the large bandwidth. To this end, we propose a practical hybrid precoding scheme with finite-resolution phase shifters by leveraging the correlation among the subchannels. Furthermore, we utilize the sparse feature of the mmWave channels to design a low-complexity algorithm to realize the proposed hybrid precoding, which can avoid the complication of the high-dimensionality eigenvalue decomposition. Simulation results show that the proposed hybrid precoding can approach the performance of unconstrained fully-digital precoding but with low hardware cost and computational complexity.

This paper presents the design and experimental evaluation of 60GHz small cell radio access based on IEEE 802.11ad/WiGig. The access point (AP) prototype used combines three RF modules with beamforming technology to provide 360° area coverage. In order to compensate for limited communication distance, multiple APs are employed to achieve wide area coverage. A handover algorithm suitable for IEEE 802.11ad/WiGig is employed to achieve flexible control of the cell coverage of each AP. As a proof of concept, a prototype system is set up at Narita International Airport and the capability of multiuser Gb/s wireless access is successfully demonstrated. In addition, the system behavior under stringent conditions is evaluated by load testing and throughput degradation due to co-channel and inter-channel interference is investigated.

Attaining extremely low latency service in 5G cellular networks is an important challenge in the communication research field. A higher QoS in the next-generation network could enable several unprecedented services, such as Tactile Internet, Augmented Reality, and Virtual Reality. However, these services will all need support from powerful computational resources provided through cloud computing. Unfortunately, the geolocation of cloud data centers could be insufficient to satisfy the latency aimed for in 5G networks. The physical distance between servers and users will sometimes be too great to enable quick reaction within the service time boundary. The problem of long latency resulting from long communication distances can be solved by Mobile Edge Computing (MEC), though, which places many servers along the edges of networks. MEC can provide shorter communication latency, but total latency consists of both the transmission and the processing times. Always selecting the closest edge server will lead to a longer computing latency in many cases, especially when there is a mass of users around particular edge servers. Therefore, the research studies the effects of both latencies. The communication latency is represented by hop count, and the computation latency is modeled by processor sharing (PS). An optimization model and selection policies are also proposed. Quantitative evaluations using simulations show that selecting a server according to the lowest total latency leads to the best performance, and permitting an over-latency barrier would further improve results.

Recently, mobile networks employing high-speed high-capacity communications have been investigated extensively to satisfy the demand for faster and higher-capacity data communications. In one approach, frequencies between 6 and 100GHz are candidates to utilize relatively wide frequency bandwidths. Accordingly, radio propagation loss in these frequency bands must be characterized. Ray-tracing (RT) is the most common modeling approach to predict propagation loss in site-specific scenarios. The accuracy of RT simulations has been investigated in urban street cell environments based on comparison to measurement results and we observed that the difference between RT simulation and measurement results tends to increase as the frequency increases. In this paper, we focus on the shape of building corners at an intersection because it is this shape that is a dominant contributing factor in the region away from the intersection. In order to correct the error in the conventional RT method, we propose an alternative model that considers the detailed shape of the building corner and surface roughness. The performance of the RT simulation using the proposed method is then investigated based on comparison of two different sets of measurement results. Finally, we extract the optimal size and roughness for the proposed modeling method. Consequently, we confirm that using the proposed method with optimized parameters significantly enhances the accuracy compared to the conventional method.