An aperture-shared multi-port waveguide antenna with multiple feeds is presented in this paper. The antenna consists of sequentially rotated four traditional WR-28 waveguides at 28GHz so as to create a multi-polarized function with decoupling between the ports. In addition, a rectangular DR (Dielectric resonator) is mounted at the center of the four apertures to obtain lower mutual coupling over a wide band and to suppress the cross-polarization in the antenna boresight direction. The proposed antenna achieves high gain of 14.4dBi, low mutual coupling of ≤-20dB on average, sufficient cross-polarization discrimination level at ≃20dB in the 27-29GHz frequency band.

5G has achieved large-scale commercialization across the world and the global 6G research and development is accelerating. To support more new use cases, 6G mobile communication systems should satisfy extreme performance requirements far beyond 5G. The physical layer key technologies are the basis of the evolution of mobile communication systems of each generation, among which three key technologies, i.e., duplex, waveform and multiple access, are the iconic characteristics of mobile communication systems of each generation. In this paper, we systematically review the development history and trend of the three key technologies and define the Non-Orthogonal Physical Layer (NOPHY) concept for 6G, including Non-Orthogonal Duplex (NOD), Non-Orthogonal Multiple Access (NOMA) and Non-Orthogonal Waveform (NOW). Firstly, we analyze the necessity and feasibility of NOPHY from the perspective of capacity gain and implementation complexity. Then we discuss the recent progress of NOD, NOMA and NOW, and highlight several candidate technologies and their potential performance gain. Finally, combined with the new trend of 6G, we put forward a unified physical layer design based on NOPHY that well balances performance against flexibility, and point out the possible direction for the research and development of 6G physical layer key technologies.

For many countries in the world, 5G is of strategic significance. In the 5G era, telecom operators are expected to enable and provide multiple services with different communication characteristics like enhanced broadband, ultra-reliable and extreme real-time communications at the same time. To meet the requirements, the 5G network essentially will be more complex compared with traditional 3G/4G networks. The unique characteristics of 5G resulted from new technologies bring a lot of opportunities as well as significant challenges. In this paper we first introduce 5G vision and check the global status. And then we illustrate the 5G technical essentials and point out the new opportunities that 5G will bring to us. We also highlight the coming challenges and share our 5G experience and solutions toward 5G vision in many aspects, including network, management and business.

In this paper, we propose new radio access network (RAN) architecture for reliable millimeter-wave (mmWave) communications, which has the flexibility to meet users' diverse and fluctuating requirements in terms of communication quality. This architecture is composed of multiple radio units (RUs) connected to a common distributed unit (DU) via fronthaul links to virtually enlarge its coverage. We further present grant-free non-orthogonal multiple access (GF-NOMA) for low-latency uplink communications with a massive number of users and robust coordinated multi-point (CoMP) transmission using blockage prediction for uplink/downlink communications with a high data rate and a guaranteed minimum data rate as the technical pillars of the proposed RAN. The numerical results indicate that our proposed architecture can meet completely different user requirements and realize a user-centric design of the RAN for beyond 5G/6G.

5G service has been launched in various countries, and research for the beyond 5G is already underway actively around the world. In beyond 5G, it is expected to expand the various capabilities of communication technologies to cover further wide use cases from 5G. As a candidate elemental technology, cell free massive MIMO has been widely researched and shown its potential to enhance the capabilities from various aspects. However, for deploying this technology in reality, there are still many technical issues such as a cost of distributing antenna and installing fronthaul, and also the scalability aspects. This paper surveys research trends of cell free massive MIMO, especially focusing on the deployment challenges with an introduction to our specific related research activities including some numerical examples.

The expansion of the communication area is expected for Beyond-5G/6G networks using the High Altitude Platform Station (HAPS), Internet of Things (IoT), and sensor devices. Beyond-5G/6G networks constitute the vast amounts of devices that require the latest power utilization system. We expect Microwave Power Transfer (MPT) plays a role in the wireless power supply to HAPS, IoT, and sensors in this network. This work discusses the link design and techniques of MPT for the newest power utilization system required on Beyond-5G/6G networks.

GaN microwave monolithic integrated circuit (MMIC) power amplifiers (PAs) technologies for millimeter-wave (mm-wave) applications are reviewed in this paper. In the mm-wave band, GaN PAs have achieved high-output power as much as traveling wave tube amplifiers used in satellite communications. Additionally, GaN PAs have been integrated enough to be used for 5G and Beyond-5G. In this paper, a high accuracy large-signal GaN-HEMT modeling technique including the trapping effects is introduced in mm-waves. The prototyped PAs designed with the novel modeling technique have achieved RF performance comparable to that of the state-of-the-art GaN PAs in mm-wave.

This paper presents a fully integrated yet compact receiver front-end for Sub-GHz applications such as Internet-of-Things (IoT). The low noise amplifier (LNA) matching network leverages an inductance boosting technique. A relatively small on-chip inductor with a compact area achieves impedance matching in such a low frequency. Moreover, a passive-mixer-first mode bypasses the LNA to extend the receiver dynamic-range. The passive mixer provides matching to the 50Ω antenna interface to eliminate the need for additional passive components. Therefore, the receiver can be fully-integrated without any off-chip matching components. The flipped-voltage-follower (FVF) cell is adopted in the low pass filter (LPF) and the variable gain amplifier (VGA) for its high linearity and low power consumption. Fabricated in 65nm LP CMOS process, the proposed receiver front-end occupies 0.37mm2 core area, with a tolerable input power ranging from -91.5dBm to -1dBm for 500kbps GMSK signal at 924MHz frequency. The power consumption is 1mW power under a 1.2V supply.

In this paper, millimeter wave (mmWave) filtenna arrays for 5G applications are proposed. Two kinds of 2-element subarrays are designed for horizontal and vertical polarizations. Each subarray consists of three substrate integrated waveguide (SIW) cavities and two sets of stacked patches. Fully-shielded combined eighth-mode SIW (FSD-CEMSIW) cavities are used in the filtenna design. This cavity not only works as the first-stage resonator but also as the power divider for the subarray. As a result, a four-order bandpass filtering response is achieved. Filtenna arrays were fabricated and measured for demonstration. The impedance bandwidths of these subarrays cover 24-30GHz, including the 5G mmWave bands (n257, n258, and n261) with measured average gains of 8.2dBi and more than 22dB out-of-band suppression. The proposed antennas can be good candidates for 5G mmWave communication to reduce the system complexity and potential cost of the mmWave front-ends.

Currently, as the widespread usage of the smart devices in our daily life, the demands of high data rate and low latency services become important issues to facilitate various applications. However, high data rate service usually implies large bandwidth requirement. To solve the problem of bandwidth shortage below 6GHz (sub-6G), future wireless communications can be up-converted to the millimeter-wave (mm-wave) bands. Nevertheless, mm-wave frequency bands suffer from high channel attenuation and serious penetration loss compared with sub-6G frequency bands, and the signal transmission in the indoor environment will furthermore be affected by various partition materials, such as concrete, wood, glass, etc. Therefore, the fifth-generation (5G) mobile communication system may use multiple small cells (SC) to overcome the signal attenuation caused by using mm-wave bands. This paper will analyze the attenuation characteristics of some common partition materials in indoor environments. Besides, the performances, such as the received signal power, signal to interference plus noise ratio (SINR) and system capacity for different SC deployments are simulated and analyzed to provide the suitable guideline for each SC deployments.

The non-orthogonal multiple access (NOMA) approach has been developed in the fifth-generation mobile communication systems (5G) and beyond, to improve the spectrum efficiency and accommodate a large number of IoT devices. Although power domain NOMA is a promising candidate, it is vulnerable to the nonlinearity of RF circuits and cannot achieve high-throughput transmission using high-level modulations in nonlinear environments. This study proposes a novel post-reception nonlinear compensation scheme consisting of two blind nonlinear compensators (BNLCs) and a frequency-domain equalizer (FDE) to reduce the effect of nonlinear distortion. The improvement possible with the proposed scheme is evaluated by using the error vector magnitude (EVM) of the received signal, which is obtained through computer simulations. The simulation results confirm that the proposed scheme can effectively improve the quality of the received downlink power-domain NOMA signal and enable high-throughput transmission under the transmitter (Tx) and receiver (Rx) nonlinearities via a frequency-selective fading channel.

Recently connected car called Vehicle-to-Everything (V2X) has been attracted for smart automotive mobility. Among V2X technologies, cellular V2X (C-V2X) discussed and specified in 3rd generation partnership project (3GPP) is generally regarded as possibly utilized one. In 3GPP, the fourth generation mobile communication system (4G) and the fifth generation (5G) including new radio (NR) provide C-V2X standards specifications. In this paper, we will introduce C-V2X standards and share our views on future C-V2X.

Fifth-generation (5G) mobile communication systems employ beamforming technology using massive multiple-input and multiple-output (MIMO) to improve the reception quality and spectrum efficiency within a cell. Meanwhile, coordinated beamforming among multiple base stations is an effective approach to improving the spectrum efficiency at the cell edges, in which massive MIMO is deployed at geographically distant base stations and beamforming control is conducted in a cooperative manner. Codebook-based beamforming is a method for realizing multi-cell coordinated beamforming, in which each base station selects one of multiple beams that are predefined in a codebook. In codebook-based beamforming, it is important to design an efficient codebook that takes into account the beam allocation and the number of beams. In general, the larger the number of beams defined in a codebook, the more finely tuned the beam control can be and a greater improvement in spectrum efficiency can be expected. However, it requires a huge signal processing to optimize the beam combinations with a large number of beams by coordinated beamforming. This paper proposes a novel codebook design that efficiently assigns beam directions and widths in a vertical plane. Computer simulations showed that the proposed codebook performs as well as the conventional method while requiring fewer beam combinations.

Through the concept of network slicing, a single physical network infrastructure can be split into multiple logically-independent Network Slices (NS), each of which is customized for the needs of its respective individual user or industrial vertical. In the beyond 5G (B5G) system, this customization can be done for many targeted services, including, but not limited to, 5G use cases and beyond 5G. The network slices should be optimized and customized to stitch a suitable environment for targeted industrial services and verticals. This paper proposes a novel Quality of Service (QoS) framework that optimizes and customizes the network slices to ensure the service level agreement (SLA) in terms of end-to-end reliability, delay, and bandwidth communication. The proposed framework makes use of network softwarization technologies, including software-defined networking (SDN) and network function virtualization (NFV), to preserve the SLA and ensure elasticity in managing the NS. This paper also mathematically models the end-to-end network by considering three parts: radio access network (RAN), transport network (TN), and core network (CN). The network is modeled in an abstract manner based on these three parts. Finally, we develop a prototype system to implement these algorithms using the open network operating system (ONOS) as a SDN controller. Simulations are conducted using the Mininet simulator. The results show that our QoS framework and the proposed resource allocation algorithms can effectively schedule network resources for various NS types and provide reliable E2E QoS services to end-users.

In this paper, a novel method of resource abstraction and an abstracted-resource model for dynamic resource control in optical access networks are proposed. Based on this proposal, an implementation assuming application to 5G mobile fronthaul and backhaul is presented. Finally, an evaluation of the processing time for resource allocation using this method is performed using a software prototype of the control function. From the results of the evaluation, it is confirmed that the proposed method offers better characteristics than former approaches, and is suitable for dynamic resource control in 5G applications.

This paper introduces a high-resolution and compact CMOS switch-type phase shifter (STPS) for the 5th generation mobile network (5G) n260 band. In this work, totally four coarse phase shifting stages and a high-resolution tuning stage are included. The coarse stages based on the bridged-T topology is capable of providing 202.5° phase coverage with a 22.5° tuning step. To further improve the phase shifting resolution, a compact fine-tuning stage covering 23° is also integrated with the coarse stages. Sub-degree phase shifting resolution is realized for supporting the fine beam-steering and high-accuracy phase calibration in the 5G new radio. Simplified phase control algorithm and suppressed insertion loss can also be maintained by the proposed fine-tuning stage. In the measurement, the achieved RMS gain errors at 39 GHz are 0.1 dB and 0.4 dB for the coarse stages and fine stage, respectively. The achieved RMS phase errors at 39 GHz are 3.1° for the coarse stages and 0.1° for the fine stage. Within 37 GHz to 40 GHz, the measured return loss within all phase-tuning states is always better than -14 dB. The proposed phase shifter consumes a core area of only 0.12mm2 with 65-nm CMOS process, which is area-efficient.

In-band full-duplex (IBFD) has been an attractive technology, which can theoretically double the spectral efficiency. However, when performing IBFD in the dynamic-duplex cellular (DDC) system, inter-user interference (IUI) deteriorates transmission performance in downlink (DL) communication and limits IBFD-applicable area and IBFD application ratio. In this paper, to expand the IBFD-applicable area and improve the IBFD application ratio, we propose an IUI reduction scheme using successive interference cancellation (SIC) for the DDC system. SIC can utilize the power difference and reduce the signal with the higher power. The effectiveness of the proposed scheme is evaluated by the computer simulation. The IUI reducing effect on the IBFD-inapplicable area is confirmed when the received power of the IUI is stronger than that of the desired signal at the user equipment for DL (DL-UE). The IBFD-inapplicable area within 95m from the DL-UE, where the IBFD does not work without the proposed scheme, can reduce by 43.6% from 52.8% to 9.2% by applying the proposed scheme. Moreover, the IBFD application ratio can improve by 24.6% from 69.5% to 94.1%.

Leveraging on Network Function Virtualization (NFV) and Software Defined Networking (SDN), network slicing (NS) is recognized as a key technology that enables the 5G Infrastructure Provider (InP) to support diversified vertical services over a shared common physical infrastructure. 5G end-to-end (E2E) NS is a logical virtual network that spans across the 5G network. Existing works on improving the reliability of the 5G mainly focus on reliable wireless communications, on the other hand, the reliability of an NS also refers to the ability of the NS system to provide continued service. Hence, in this work, we focus on enhancing the reliability of the NS to cope with physical network node failures, and we investigate the NS deployment problem to improve the reliability of the system represented by the NS. The reliability of an NS is enhanced by two means: firstly, by considering the topology information of an NS, critical virtual nodes are backed up to allow failure recovery; secondly, the embedding of the augmented NS virtual network is optimized for failure avoidance. We formulate the embedding of the augmented virtual network (AVN) to maximize the survivability of the NS system as the survivable AVN embedding (S-AVNE) problem through an Integer Linear Program (ILP) formulation. Due to the complexity of the problem, a heuristic algorithm is introduced. Finally, we conduct intensive simulations to evaluate the performance of our algorithm with regard to improving the reliability of the NS system.

Network Slicing (NS) is recognized as a key technology for the 5G network in providing tailored network services towards various types of verticals over a shared physical infrastructure. It offers the flexibility of on-demand provisioning of diverse services based on tenants' requirements in a dynamic environment. In this work, we focus on two important issues related to 5G Core slices: the deployment and the reconfiguration of 5G Core NSs. Firstly, for slice deployment, balancing the workloads of the underlying network is beneficial in mitigating resource fragmentation for accommodating the future unknown network slice requests. In this vein, we formulate a load-balancing oriented 5G Core NS deployment problem through an Integer Linear Program (ILP) formulation. Further, for slice reconfiguration, we propose a reactive strategy to accommodate a rejected NS request by reorganizing the already-deployed NSs. Typically, the NS deployment algorithm is reutilized with slacked physical resources to find out the congested part of the network, due to which the NS is rejected. Then, these congested physical nodes and links are reconfigured by migrating virtual network functions and virtual links, to re-balance the utilization of the whole physical network. To evaluate the performance of deployment and reconfiguration algorithms we proposed, extensive simulations have been conducted. The results show that our deployment algorithm performs better in resource balancing, hence achieves higher acceptance ratio by comparing to existing works. Moreover, our reconfiguration algorithm improves resource utilization by accommodating more NSs in a dynamic environment.

In Feb 2021, As the competition for commercialization of 5G mobile communication has been increasing, 5G SA Network and Vo5G are expected to be commercialized soon. 5G mobile communication aims to provide 20 Gbps transmission speed which is 20 times faster than 4G mobile communication, connection of at least 1 million devices per 1 km2, and 1 ms transmission delay which is 10 times shorter than 4G. To meet this, various technological developments were required, and various technologies such as Massive MIMO (Multiple-Input and Multiple-Output), mmWave, and small cell network were developed and applied in the area of 5G access network. However, in the core network area, the components constituting the LTE (Long Term Evolution) core network are utilized as they are in the NSA (Non-Standalone) architecture, and only the changes in the SA (Standalone) architecture have occurred. Also, in the network area for providing the voice service, the IMS (IP Multimedia Subsystem) infrastructure is still used in the SA architecture. Here, the issue is that while 5G mobile communication is evolving openly to provide various services, security elements are vulnerable to various cyber-attacks because they maintain the same form as before. Therefore, in this paper, we will look at what the network standard for 5G voice service provision consists of, and what are the vulnerable problems in terms of security. And We Suggest Possible Attack Scenario using Security Issue, We also want to consider whether these problems can actually occur and what is the countermeasure.