Combination of mutually complementary features is necessary to cope with various changes in pattern classification between normal and pathological voices. This paper proposes a method to improve pathological/normal voice classification performance by combining heterogeneous features. Different combinations of auditory-based and higher-order features are investigated. Their performances are measured by Gaussian mixture models (GMMs), linear discriminant analysis (LDA), and a classification and regression tree (CART) method. The proposed classification method by using the CART analysis is shown to be an effective method for pathological voice detection, with a 92.7% classification performance rate. This is a noticeable improvement of 54.32% compared to the MFCC-based GMM algorithm in terms of error reduction.

This letter deals with computationally efficient maximum-likelihood (ML) detection for the quasi-orthogonal space-time block code (QOSTBC) with four transmit antennas. The proposed ML detector uses a permutation based real-valued equivalent channel matrix representation. As a result, the complexity of ML detection problem is moderated from O(2|A|2) to O(4|A|), where |A| is modulation order. Numerical results show that the proposed ML detector provides ML performance and achieves greatly high computational savings.

This paper presents a new interactive learning method for spoken word acquisition through human-machine audio-visual interfaces. During the course of learning, the machine makes a decision about whether an orally input word is a word in the lexicon the machine has learned, using both speech and visual cues. Learning is carried out on-line, incrementally, based on a combination of active and unsupervised learning principles. If the machine judges with a high degree of confidence that its decision is correct, it learns the statistical models of the word and a corresponding image category as its meaning in an unsupervised way. Otherwise, it asks the user a question in an active way. The function used to estimate the degree of confidence is also learned adaptively on-line. Experimental results show that the combination of active and unsupervised learning principles enables the machine and the user to adapt to each other, which makes the learning process more efficient.

Burn-in is a widely used method to improve the quality of products or systems after they have been produced. In this paper, optimal burn-in procedures for a system with two types of failures (i.e., minor and catastrophic failures) are investigated. A new system surviving burn-in time b is put into field operation and the system is used under a warranty policy under which the manufacturer agrees to provide a replacement system for any system that fails to achieve a lifetime of at least w. Upper bounds for optimal burn-in time minimizing the total expected warranty cost are obtained under a more general assumption on the shape of the failure rate function which includes the bathtub shaped failure rate function as a special case.

Multi-carrier code division multiple access (MC-CDMA) has been considered as one of the promising techniques for the next generation of mobile communication systems because of its efficient bandwidth usage, robustness to the multi-path fading and simple channel-sharing scheme. However, MC-CDMA cannot be employed in the uplink communication where the transmitted signal from each user propagates through the different multi-path fading channel, and the received signals are no longer orthogonal at the base station. As a result, bit error rate (BER) performance in the uplink MC-CDMA communication would be strongly degraded due to the occurrence of multi-user interference (MUI). To solve the MUI problem in the uplink MC-CDMA, the pre-equalization method was proposed in which the uplink signal is pre-equalized at the user terminal by using the channel response estimated from the downlink. Although the pre-equalization method is very effective for the stationary uplink channel with fixed users, it is hard to be employed in the time varying fading channel with mobile users, because there is a big difference in the channel responses between downlink and uplink. For the efficient MUI compensation, each user terminal would be required to predict the future channel conditions based on the current observation. This paper proposes a method for model based uplink channel response prediction by employing the spectral decomposition of the downlink channel impulse response. Computer simulation results show that the proposed method can achieve the accurate prediction of channel response for mobile users during the uplink transmission and allows the effective MUI compensation.

Effect of the post-growth annealing on the morphology of a Ge mesa selectively grown on Si was studied from the viewpoint of near-infrared photodiode applications. By ultrahigh-vacuum chemical vapor deposition, Ge mesas were selectively grown at 600 on Si (001) substrates partially covered with SiO2 masks. The as-grown Ge mesas showed trapezoidal cross-sections having a top (001) surface and {311} sidewall facets, as similar to previous reports. However, after the subsequent post-growth annealing at ~800 in the ultrahigh-vacuum chamber, the mesas were deformed into rounded shapes having a depression at the center and mounds near the edges. Such a deformation cannot be observed for the samples annealed once after cooled and exposed to the air. The residual hydrogen atoms on the Ge surface from the germane (GeH4) decomposition is regarded as a trigger to the observed morphological instability, while the final mesa shape is determined in order to minimize a sum of the surface and/or strain energies.

The combination of Multiple-Input Multiple-Output (MIMO) and Orthogonal Frequency Division Multiplexing (OFDM) technologies gives wireless communications systems the advantages of lower bit error rate (BER) and higher data rate in frequency-selective fading environments. However, the main drawbacks of MIMO systems are their high complexity and high cost. Therefore, antenna selection in MIMO systems has been shown to be an effective way to overcome the drawbacks. In this paper, we propose two receive antenna selection methods for a MIMO-OFDM system with radio frequency (RF) switches and polarization antenna elements at the receiver side, taking into consideration low computational complexity. The first method selects a set of polarization antenna elements which gives lower correlation between received signals and larger received signal power, thus achieves a lower BER with low computational complexity. The second method first selects a set of polarization antenna elements based on the criterion of the first method and another set of polarization antenna elements based on the criterion of minimizing the correlation between the received signals; it then calculates the signal-to-interference-plus-noise power ratio (SINR) of the two sets and selects a set with larger SINR. As a result, the second method achieves a better BER than the first one but it also requires higher computational complexity than the first one. We use the measured channel data to evaluate the performance of the two methods and show that they work effectively for the realistic channel.

In this Letter, we investigate the correlation rate of a random sequence data set which is collected by RFID (Radio Frequency IDentification) readers in an indoor location. Using a passive RFID tag introduces reading error, which causes a loss of original data. From the question of how sensing errors of RFID readers affect the location prediction algorithm used for context awareness services at home, we analyze the correlation rate of a collected data set with respect to RFID reader-sensing error rate. Through our analysis, we conclude that the prediction accuracy can be better or worse than the one of the original data streams according to the error rate. We suggest that the reader specification has to be satisfied by the error boundary which is found in this work for the tolerant location prediction.

For real time image processing, a readout circuit for an infrared focal plane array (IRFPA) involving a new edge detection technique has been proposed in this letter. A non-uniformity correction unit (NUC), essential in an IRFPA because of bad non-uniformity characteristics of IR sensors is eliminated in this circuit by using a noise tolerant edge detection technique. In addition, real time edge detection can be possible, because of pixel-level integration and parallel processing. The proposed readout circuit shows an approximately three to nine times better edge error rate than other available methods using pixel-level parallel processing.

Though machine vision systems for automatically detecting visual defects, called mura, have been developed for thin flat transistor liquid crystal display (TFT-LCD) panels, they have not yet reached a level of reliability which can replace human inspectors. To establish an objective criterion for identifying real defects, some index functions for quantifying defect levels based on human perception have been recently researched. However, while these functions have been verified in the laboratory, further consideration is needed in order to apply them to real systems in the field. To begin with, we should correct the distortion occurring through the capturing of panels. Distortion can cause the defect level in the observed image to differ from that in the panel. There are several known methods to restore the observed image in general vision systems. However, TFT-LCD panel images have a unique background degradation composed of background non-uniformity and vignetting effect which cannot easily be restored through traditional methods. Therefore, in this paper we present a new method to correct background degradation of TFT-LCD panel images using principal component analysis (PCA). Experimental results show that our method properly restores the given observed images and the transformed shape of muras closely approaches the original undistorted shape.

A wireless transceiver utilizing inductive coupling has been proposed for communication between chips in system in a package. This transceiver can achieve high-speed communication by using two-dimensional channel arrays. To increase the total bandwidth in the channel arrays, the density of the transceiver should be improved, which means that the inductor size should be scaled down. This paper discusses the scaling theory based on a constant magnetic field rule. By decreasing the chip thickness with the process scaling of 1/α, the inductor size can be scaled to 1/α and the data rate can be increased by α. As a result, the number of aggregated channels can be increased by α2 and the aggregated data bandwidth can be increased by α3. The scaling theory is verified by simulations and experiments in 350, 250, 180, and 90 nm CMOS.

This paper is aimed to present the design and feasibility investigations of adopting the available on-site optical inspection system, which is commonly used for steel plate dimension measurement, to supply on-line dynamic gap measurements of a non-contacting conveyance structure in a steel mill. Adequate software and hardware implementations based on digital image processing techniques have been adapted to the entire system formulations and estimations. Results show that the system can supply accurate and rapid gap measurements and thus can fulfill the design and operational objectives.

An important issue in the realization of optical packet-switched (OPS) networks is the resolution of packet contention caused by the lack of RAM-like optical buffering. Although an optical buffer using fiber delay lines (FDLs) has been proposed, its capacity is extremely limited. There have been several studies of this problem. One approach is deflection routing, which is widely used in electronic packet-switched networks or optical burst-switched (OBS) networks. However, in OPS networks, packet lengths are short, so that the speed requirement for route lookup is very stringent. If the network topology is geometric, such as a Manhattan Street Network (MSN), hop-by-hop routing can be implemented by simple optical logic devices without an electronic routing table. However, if the topology is not geometric, it is hard to implement deflection routing electronically or optically. Another approach is reflection routing, which is easy to implement but has a higher probability of packet loss than does deflection routing. In this paper, we propose a packet contention resolution scheme, reflection-based deflection routing, which is based on reflection routing and enables switching the reflected packet to an alternate path if its primary path remains congested. Our method alleviates the time limitation on setting an alternate path by making use of the packet reflection latency and also reduces the probability of packet loss. We evaluate the performance of the proposed method by simulation experiments and show its effectiveness.

In this paper, we propose a soft decision based cooperative sensing method for cognitive radio (CR) networks for opportunistic frequency usage. To identify unused frequency, CR should exploit sensing technique to detect presence or absence of primary user and use this information to opportunistically provide communication among secondary users while performance of primary user should not be deteriorated by the secondary users. Because of multipath fading or shadowing, the detection of primary users may be significantly difficult. For this problem, cooperative sensing (CS), where gathered observations obtained by multiple secondary users is utilized to achieve higher performance of detection, has been investigated. We design a soft decision based CS analytically and analyze the detector in several situations, i.e., signal model where single-carrier case and multi-carrier case are assumed and two scenarios; in the first scenario, SNR values of secondary users are totally equal and in the second scenario, a certain SNR difference between secondary users is assumed. We present numerical results as follows. The first scenario shows that there is little difference between the signal models in terms of detection performance. The second scenario shows that CS is superior to non-cooperative sensing. In addition, we presents that detection performance of soft decision based CS outperform detection performance of hard decision based CS.

The concept of placing enormous Solar Power Satellite (SPS) systems in space represents one of a handful of new technological options that might provide large scale, environmentally clean base load power to terrestrial markets. Recent advances in space exploration have shown a great need for antennas with high resolution, high gain and low side lobe level (SLL). The last characteristic is of paramount importance especially for the Microwave Power Transmission (MPT) in order to achieve higher transmitting efficiency (TE) and higher beam collection efficiency (BCE). In order to achieve low side lobe levels, statistical methods play an important role. Various interesting properties of a large antenna arrays with randomly, uniformly and combined spacing of elements have been studied, especially the relationship between the required number of elements and their appropriate spacing from one viewpoint and the desired SLL, the aperture dimension, the beamwidth and TE from the other. We propose a new unified approach in searching for reducing SLL by exploiting the interaction of deterministic and stochastic workspaces of proposed algorithms. Our models indicate the side lobe levels in a large area around the main beam and strongly reduce SLL in the entire visible range. A new concept of designing a large antenna array system is proposed. Our theoretic study and simulation results clarify how to deal with the problems of side lobes in designing a large antenna array, which seems to be an important step toward the realization of future SPS/MPT systems.

We propose a neurodynamical approach to a large-scale optimization problem in Cognitive Wireless Clouds, in which a huge number of mobile terminals with multiple different air interfaces autonomously utilize the most appropriate infrastructure wireless networks, by sensing available wireless networks, selecting the most appropriate one, and reconfiguring themselves with seamless handover to the target networks. To deal with such a cognitive radio network, game theory has been applied in order to analyze the stability of the dynamical systems consisting of the mobile terminals' distributed behaviors, but it is not a tool for globally optimizing the state of the network. As a natural optimization dynamical system model suitable for large-scale complex systems, we introduce the neural network dynamics which converges to an optimal state since its property is to continually decrease its energy function. In this paper, we apply such neurodynamics to the optimization problem of radio access technology selection. We compose a neural network that solves the problem, and we show that it is possible to improve total average throughput simply by using distributed and autonomous neuron updates on the terminal side.

In this paper, an architecture of MIMO mesh network which avoids co-channel interference and supplies link multiplexing simultaneously, namely MIMO spatial spectrum sharing, is proposed. As a MIMO transmission scheme, linear (such as zero-forcing) and nonlinear (such as dirty paper coding and successive interference cancellation) MIMO algorithm are developed for the proposed mesh network. It is found from numerical analysis that the proposed MIMO mesh network achieves significantly higher channel capacity than that of conventional mesh networks.

In this paper we analyze the characteristics of vehicle mobility and propose a novel Mobility Prediction Progressive Routing (MP2R) protocol for Inter-Vehicle Communication (IVC) that is based on cross-layer design. MP2R utilizes the additional gain provided by the directional antennas to improve link quality and connectivity; interference is reduced by the directional transmission. Each node learns its own position and speed and that of other nodes, and performs position prediction. (i) With the predicted progress and link quality, the forwarding decision of a packet is locally made, just before the packet is actually transmitted. In addition the load at the forwarder is considered in order to avoid congestion. (ii) The predicted geographic direction is used to control the beam of the directional antenna. The proposed MP2R protocol is especially suitable for forwarding burst traffic in highly mobile environments. Simulation results show that MP2R effectively reduces Packet Error Ratio (PER) compared with both topology-based routing (AODV [1], FSR [2]) and normal progressive routing (NADV [18]) in the IVC scenarios.

The combination of deliberate clipping and an adaptive symbol selection scheme (ASSS) can be used to reduce the peak to average power ratio (PAPR) for Orthogonal Frequency Division Multiplexing (OFDM) signals. The probability density function (pdf) of a sample's amplitude of an adaptively selected OFDM signal without over-sampling has been considered to be approximately equal to the Rayleigh pdf. In this letter, we derive the exact pdf showing the relationship between the probability distribution of the sample's amplitude and the number of candidate OFDM symbols for ASSS. The use of the newly derived pdf can measure the effect of deliberate clipping on the adaptively selected OFDM signal more accurately.

This paper deals with the scattering of a transverse magnetic (TM) plane wave from a perfectly conductive sinusoidal surface with finite extent. By use of the undersampling approximation and a rectangular pulse approximation, an asymptotic formula for the total scattering cross section at a low grazing limit of incident angle is obtained explicitly under conditions such that the surface is small in roughness and slope, and the corrugation width is sufficiently large. The formula shows that the total scattering cross section is proportional to the square root of the corrugation width but does not depend on the surface period and surface roughness. When the corrugation width is not large, however, the scattered wave can be obtained by a single scattering approximation, which gives the total scattering cross section proportional to the corrugation width and the Rayleigh slope parameter. From the asymptotic formula and the single scattering solution, a transition point is defined explicitly. By comparison with numerical results, it is concluded that the asymptotic formula is fairly accurate when the corrugation width is much larger than the transition point.