Intricate Speech Communication Mode (I-SC Mode) is observed in verbal interaction during ISDN-TV conferencing. It is characterized by conflicts and multiple interactions of speech. I-SC Mode might cause mental stress to participants and be obstacles for smooth communication. However, the reasons of I-SC Mode on the environment of information transmission are hitherto unknown. Furthermore, analyses on the talks inside a conference site (LT: local talk or a talk inside a local site) and between remote sites (MT: media talk or a talk between remote sites) are originally conceived on assumed differences in cognitive distance and media intimacy. This study deals with communication effects/barriers and cognitive distance/intimacy of media correlated with audio-video transmission signals and speech modes or talk types and response delay in human speech interactions by using an innovated conference model (decision-making transaction model: DT-Model) in synchronous ISDN-TV conference systems (SYN) and asynchronous ones (ASYN). The effects of intricate communication can be predicted to a certain extent and in some ways. In I-SC Mode, because a timely answer can not be received from recipients (or partner), response time delay and response rate are analyzed. These factors are thus analyzed with an innovated dynamic model, where the recognizable acceptance of delay is evaluated. The nonlinear model shows that the larger the response time delay, the lower the response rate becomes. Comparing the response rate between SYN and ASYN, the latter is notably lower than the former. This indicates that the communication efficiency is lower in ASYN. An I-SC Mode is the main mode that occurs during ASYN conferences, and this in turn causes psychological stress. Statistics show the prevalence of a high incidence of complicated plural talks and a low response rate exists as the main factors preventing smooth human-to-human communication. Furthermore, comparing the response delays in face-to-face LT (Tf) and machine-mediated MT (Tm), human communication delay is significantly extended by the effects of initial mechanical delays. Therefore, cognitive intimacy of media is clearly affected by the existence of physical distance.

In this paper, authors propose a linear array antenna using two bifilar helical antenna elements placed along the helix axis to reduce beam direction movement according to frequency change. The beam direction movement of this proposed array antenna is smaller than that of a conventional bifilar helical antenna. Also, the gain of this proposed array antenna is higher than that of the conventional helical antenna for a cross point angle of radiation patterns at the different transmit and receive(Tx and Rx) frequencies. The conventional helical antenna is suitable for vehicle antennas in mobile satellite communication systems such as the MSAT system because it owns circularly polarized omni-directional radiation pattern and its thin pole form. However, this antenna has a disadvantage that the beam direction in an elevation plane moves according to frequency change. In the proposed array antenna, the beam direction movement is about 9 smaller than that of the conventional bifilar helical antenna on condition that antenna total length is 4.83 λ0, antenna diameter is 0.12 λ0, and frequency change is from 0.957f0 to 1.043f0(f0 is center frequency and λ0 is free space wavelength at f0). Also, the Tx and Rx gains of this proposed array antenna at the cross point angle between Tx and Rx beams are about 2 dB higher than that of the conventional bifilar helical antenna on the same condition.

This paper proposes a new digitized group modulator for radio base station transmitters of multi-carrier TDMA. This group modulator can flexibly set carrier spacing and features a simple construction as a result of employing the Simple Fractional Sampling technique. A group modulator LSI was designed and built using 0.5-µm BiCMOS technology, and a π/4-shifted QPSK group modulator was constructed using this LSI. Experiments confirm that the modulator simultaneously generates multiple carriers in a wide bandwidth without the need for precise adjustment and there is little difference between each of the carriers in terms of BER performance. Moreover, experiments confirm that the group modulator's burst-output (frequency hopping) performance is excellent.

The problem of genetic algorithm's efficiency has been attracting the attention of genetic algorithm community. Over the last decade, considerable researches have focused on improving genetic algorithm's performance. However, they are generally under the framework of natural evolutionary mechanism and the major genetic operators, crossover and mutation, are activated by the prior probabilities. An operator based on a prior probability possesses randomness, that is, the unexpected individuals are frequently operated, but the expected individuals are sometimes not operated. Moreover, as the evaluation function is the link between the genetic algorithm and the problem to be solved, the evaluation function provides the heuristic information for evolutionary search. Therefore, how to use this kind of heuristic information (present and past) is influential in the efficiency of evolutionary search. This paper, as an attempt, presents a eugenics-based genetic algorithm (EGA) -- a genetic algorithm that reflects the human's decision will (eugenics), and fully utilizes the heuristic information provided by the evaluation function for the decisions. In other words, EGA = evolutionary mechanisms + human's decision will + heuristic information. In EGA, the ideas of the positive eugenics and the negative eugenics are applied as the principle of selections and the selections are not activated by the prior probabilities but by the evaluation values of individuals. A method of genealogical chain-based selection for mutation is proposed, which avoids the blindness of stochastic mutation and the disruptive problem of mutation. A control strategy of reasonable competitions is proposed, which brings the effects of crossover and mutation into full play. Three examples, the minimum problem of a standard optimizing function--De Jong's test function F2, a typical combinatorial optimization problem--the traveling salesman problem, and a problem of identifying nonlinear system, are given to show the good performance of EGA.

A new neural network for locating a source by integrating data from a number of sensors is considered. The network gives a solution for inverse problems using a back-propagation algorithm with the architecture to get the solution in the inter-layer weights in a coded form Three different physical quantities are applied to the network, since the scheme has three independent ports; an input port, a tutorial port and an answer port. Our architecture is useful to estimate z" in the problem whose structure is y=f(x,z) where y is the observed data, x is the sensor position and z is the source location. The network integrates the information obtained from a number of sensors and estimates the location of the source. We apply the network to two problems of location estimation: the localization of the active nerves from their evoked potential waveforms and the localization of objects from their echoes using an active sonar system.

A simplified equivalent circuit, which is useful in L-band, of switching MOSFET is presented. The MOSFET model accounts for the relatively low resistivity of Si substrate. By using this circuits, the relationship between the MOSFET equivalent circuit parameters and a series-shunt FET connected SPDT switch characteristics has been revealed. In order to evaluate the relationship mentioned above, enhancement type NMOSFETs and a SPDT switch with the FETs are fabricated. The MOSFET equivalent circuit parameters at L-band were extracted from measured small-signal S-parameters of the FETs. The measured switch characteristics are fairly good agreement with the simulated results which has been accomplished by using the MOSFET model. This good agreements shows the effectiveness of the MOSFET model which is presented here.

A multi-terminal serial optical link(MSOL) achieves very simple and cost effective radio cell configurations because only one pair of fibers is needed. In addition, low cost Fabry-Perot laser diodes(FP-LDs) can be employed. MSOL has a substantial problem in that the beat noise degrades the C/N in the up-link. To reduce this noise, we propose using an automatic wavelength-offset control(AWOC) circuit. The AWOC circuit offsets the LD wavelength by controlling the laser bias current to minimise the RF band beat noise which is inherent in MSOL systems, and enables high C/N optical-microwave transmission. An experimental MSOL consisting of 5 radio access stations, each equipped with AWOC, is constructed to estimate the noise free dynamic range for 800-MHz 20-carrier signal transmission. The up-link comprises a single mode fiber connecting five 1.3-µm FP-LDs operating at 0.2 mW. The down-link consists of a single mode fiber and one 1.3-µm Distributed Feedback type Laser Diode(DFB-LD) emitting at 4.0 mW. The experimental device achieves over 15 dB noise reduction compared to MSOL without AWOC in the temperature range of 0 to 40. By using the proposed AWOC, MSOL can achive low cost optical fiber RF microcell systems that are easy to install. Additionally, when we install MSOL in the radio base station, the links become more cost effective than coaxial cable links; they offer a wide dynamic range and higher transmission quality.

We have developed the Epi-Base SATURN process as a silicon bipolar process technology which can be applied to optical transmission LSIs. This process technology, to which low temperature selective epitaxial growth technology is applied, is based on the SATURN process. By performing selective epitaxial growth for base formation in 2 steps, transistors with a 40GHz maximum cut-off frequency have been fabricated. In circuit simulation based on SPICE parameters of transistors, the target performance required for 2.4 Gbit/s optical interface LSIs has been achieved.

Optical switching networks to transport vast amounts of information are important for B-ISDN services. The wavelength division multiplexing (WDM) is emerging as the dominant technology for future optical networks. This paper proposes a large capacity photonic ATM switch architecture using WDM technology. The switch consists of two stages. The first stage is a space switch and the second stage is a wavelength switch. The proposed switch is suitable for WDM optical ATM networks, that is, an input and an output of the switch are wavelength-division-multiplexed. The switch can provide very large ATM cell switching capacity, for instance, 10Tbit/s, with reasonable complexity. The main switch module of the proposed switch has a simple architecture, and reduces the amount of a buffer hardware by introducing the WDM concept.

The main propagation effect on interference between adjacent earth-space paths is considered to be the differential rain attenuation. In the present paper, a unified method for the prediction of rain differential attenuation statistics, valid for both single/dual polarization systems, which is based on the two-dimensional gamma distribution, in proposed. The method is particularly oriented for application to earth-space paths located in Japan and other locations with similar climatic conditions. From another point of view, the present work is considered to be the complementary aspect of the present work is considered to be the complementary aspect of the predictive analysis which uses the lognormal assumption. Numerical results are presented referring to communication systems suffering from differential rain attenuation under the hypothesis of using both single and dual polarization.

A decision circuit with a function of detecting the phase difference between input data and clock signal is presented. Direct coupled FET logic (DCFL) was used for basic gates. The circuit architecture was chosen to be suitable for DCFL. Novel circuit technologies were adopted to the phase detectors. In GaAs/AlGaAs pseudomorphic inverted HEMT's were used for fabrication. The decision circuit showed a wide phase margin of 288 degrees and small decision ambiguity of 27 mVpp up to 10 Gb/s. Linear and wide-range phase detection was achieved as well as an ability to compensate the variation of transition density, input bias and temperature.

This paper discusses key technologies for intelligent radio transmissions and intelligent network constitution techniques for advanced wireless communication systems. In the former part, this paper discusses the intelligent radio transmission techniques, in which the adaptive modulation techniques are mainly introduced because it is very effective to intelligently assign radio resources to each terminals as well as to intelligently control radio transmission parameters under dynamically changing traffic, required quality of services (QOS), and channel conditions. In the latter part, this paper discusses intelligent networking techniques, in which autonomous radio networking techniques and IP address control techniques for mobile host in the Internet are introduced to obtain suggestions for future intelligent and robust networking technologies.

This paper describes a CDMA cellular system based on adaptive interference cancellation (CDMA-AIC) with a large capacity. In the CDMA-AIC, each base station employs a single-user type adaptive interference canceller (AIC), which consists of a fractionally chip-spaced code-orthogonalizing filter (COF) and a coherent detector. The AIC adaptively removes power-dominant multiple-access interferences (MAIs) in the cellular system, regardless of whether they are intra-cell interferences or inter-cell interferences, without any information about them, such as spreading codes, signal received timings and channel parameters. Evaluation under the multiple-cell environment demonstrates that the reverse link capacity of the CDMA-AIC with QPSK modulation is 3.6 times as large as the capacity of the CDMA without MAI cancellation. Further, the capacity is less sensitive to transmission power control errors than that of the conventional CDMA systems.

This paper proposes an adaptive modulation system with a punctured convolutional code for land mobile communications to achieve high quality, high bit rate, and high spectral efficient data transmission in multipath fading environments. The proposed system adaptively controls the coding rate of the punctured convolutional code, symbol rate, and modulation level according to the instantaneous fading channel conditions. During good channel conditions, the modulation parameters are selected to increase the transmission rate as much as possible with satisfying a certain transmission quality. As channel conditions become worse, lower rate modulation parameters are applied or transmission is stopped. The performances in fading environments are evaluated theoretically and by computer simulations. The results show that the proposed system can realize higher quality transmission without the degradation in average bit rate compared to conventional adaptive modulation systems.

In order to pave the way to B-ISDN, one of the most important issues for network providers is to identify the most efficient B-ISDN introduction strategy. This paper focuses on the costs of introducing ATM transmission systems into backbone transport networks which must provide highly reliable broad band transmission capability. In this context, the main rival to ATM is Synchronous Transfer Mode (STM); recent Synchronous Digital Hierarchy (SDH) equipment supports the establishment of advanced STM-based high speed transport networks. This paper offers a cost comparison of ATM and STM based backbone transport networks. A digital path network in STM has a hierarchical structure determined by the hierarchical multiplexing scheme employed. The minimum cost STM path network can only be determined by developing a path design method that considers all hierarchical path levels and yields the optimum balance of link cost and node cost. Virtual paths have desirable features such as non-deterministic path bandwidth and non-hierarchical and direct multiplexing capability into high speed optical transmission links. These features make it possible to implement a non-hierarchical VP network with ATM cross connect systems which can handle any bandwidth VP with a universal cell switching function. This paper shows that the non-hierarchical VP routing, which strongly minimizes link cost, can be implemented without significantly increasing node cost. Network design simulations show that the virtual path scheme, possible only in an ATM network, yields the most cost effective path network configuration.

A new dynamic channel allocation algorithm which is integrated with transmitting power control is proposed. By introducing a new threshold, referred to as TPC threshold (Transmitting Power Control threshold), which is added some margin to the threshold of channel allocation, the subsequent transmitting power control can be performed effectively. This DCA algorithm can achieve a cellular system with both high traffic capacity and high service quality such as interference frequency performance simultaneously. The computer simulation shows that this DCA algorithm improves blocking probability performance 4 times better than that of DECT system at 14 Erlang, while keeping the same interference frequency and forced termination performances.

This paper proposes a new digitized group modulator and demodulator (a group modem) for adaptive frequency hopping and multi-carrier (AFHMC) radio systems. The group modem can flexibly vary the number of carriers handled simultaneously, especially employing a time division multiplexing technique in the demodulator. We discuss the operational principle of the modem. The required operational clock frequency in the group demodulator is also examined and clarified taking into consideration the frequency characteristics of the baseband filter. The basic performance of the proposed configuration is measured experimentally by constructing a π/4-shift QPSK group modulator and a π/4-shift QPSK group demodulator. First, by measuring the output spectrum of the significant parts in the demodulator, we confirm that the basic operational performance conforms to the design specifications. Secondly, investigating the relationship between the number of multiplexed low-pass filter taps and the required CNR when multiple carriers are simultaneously input confirms that more than 40 taps are enough to obtain the best BER performance in this experiment. Next, examining the relationship between the number of carriers simultaneously input, the required CNR, and the input level of these carriers confirm that the required CNR is roughly constant and there is no significant difference among the cases when D/U is more than 0 dB. Finally, an experiment shows that the required number of quantization bits for A/D input in the demodulator is more than 6, which is enough to obtain the best BER even if simultaneous handled carriers are 4.

Multiple TDMA bursts assignment between a base station and a personal terminal will be required for multimedia communications that offers high speed signal transmission such as voice and data simultaneous transmission. This paper proposes a reliable packet transmission method for TDMA based wireless multimedia communications. The proposed method employs an adaptive transmission rate control according to the packet length and a burst diversity technique is applied to improve the frame error rate of a packet. The frame error rate performance has been approximated theoretically by using fade- and infade-duration statistics of a Rayleigh fading channel and a computer simulation has been carried out for two control channels, FACCH/SACCH (Fast/Slow Associated Control CHannel) in the PHS as well as GSM. Both results indicate that the frame error rate is dramatically improved, about one order, when two bursts have different frequency and improved by about 25% when the two bursts have the same frequency.

A new transmit permission control scheme applicable in multi-cell communication systems is proposed. In this scheme, by prohibiting the transmissions from the users with relatively high propagation loss to their connecting hub stations, level of multiple access interference is decreased, and hence throughput characteristics are improved. Moreover, we continue our discussion to propose two adaptive forms of the transmit permission control scheme, in which the prohibition condition becomes more intelligent by considering the level of the offered traffic loads to hub stations. These methods are utilized in a slotted Aloha random transmission of the spread spectrum packets, and on the uplinks of a low earth orbit satellite communication system as an example of the multi-cell systems. It is shown that the adaptive schemes exhibits significantly improved characteristics at all offered traffic loads in these systems.

This paper overviews fiber-oriented wireless communication systems, particularly in the area of microcell systems. The benefits of fiber-oriented wireless systems are discussed focusing on an application board scheme to facilitate new service deployment in light of intelligent networks. Dynamic range improvement technologies to remove interference are highlighted. Overall system performance is calculated for an economical FP-LD. Furthermore, effective modem use and a potential diversity technique are introduced. This strategy will play a role in realizing flexible fiber-optic subscriber networks.