Hirohisa NAGATA Takehiko WADA Hirokazu IKEDA Yasuo ARAI Morifumi OHNO Koichi NAGASE
We have been developing low power cryogenic readout electronics for space borne large format far-infrared image sensors. As the circuit elements, a fully-depleted-silicon-on-insulator (FD-SOI) CMOS process was adopted because they keep good static performance even at 4.2 K where where various anomalous behaviors are seen for other types of CMOS transistors. We have designed and fabricated several test circuits with the FD-SOI CMOS process and confirmed that an operational amplifier successfully works with an open loop gain over 1000 and with a power consumption around 1.3 µW as designed, and the basic digital circuits worked well. These results prove that the FD-SOI CMOS process is a promising candidate of the ideal cryogenic readout electronics for far-infrared astronomical focal plane array sensors.
Hideyuki HATTA Takashi NAGASE Takashi KOBAYASHI Mitsuru WATANABE Kimihiro MATSUKAWA Shuichi MURAKAMI Hiroyoshi NAITO
Solution-based organic field-effect transistors (OFETs) with low parasitic capacitance have been fabricated using a self-aligned method. The self-aligned processes using a cross-linking polymer gate insulator allow fabricating electrically stable polymer OFETs with small overlap area between the source-drain electrodes and the gate electrode, whose frequency characteristics have been investigated by impedance spectroscopy (IS). The IS of polymer OFETs with self-aligned electrodes reveals frequency-dependent channel formation process and the frequency response in FET structure.
Cheng-Min LIN Shyi-Shiou WU Tse-Yi CHEN
Universal Plug and Play (UPnP) allows devices automatic discovery and control of services available in those devices connected to a Transmission Control Protocol/ Internet Protocol (TCP/IP) network. Although many products are designed using UPnP, little attention has been given to UPnP related to modeling and performance analysis. This paper uses a framework of Generalized Stochastic Petri Net (GSPN) to model and analyze the behavior of UPnP systems. The framework includes modeling UPnP, reachability decomposition, GSPN analysis, and reward assignment. Then, the Platform Independent Petri net Editor 2 (PIPE2) tool is used to model and evaluate the controllers in terms of power consumption, system utilization and network throughput. Through quantitative analysis, the steady states in the operation and notification stage dominate the system performance, and the control point is better than the device in power consumption but the device outperforms the control point in evaluating utilization. The framework and numerical results are useful to improve the quality of services provided in UPnP devices.
Karthikeyan SHOLAMPETTAI SUBRAMANIAN Rakhesh Singh KSHETRIMAYUM
In this paper, a rat-race hybrid coupler based on an open complementary split ring resonator (OCSRR) is presented. By embedding the OCSRR in the microstrip transmission line, slow-wave effect is introduced to achieve size reduction. The proposed rat-race coupler size is 37% smaller than the conventional rat-race coupler. Besides, the proposed coupler provides better third harmonic suppression up to 35 dB. The simulated results are compared with the measured data and good agreement is reported.
Ryosuke MIYOSHI Yutaka MAEDA Seiji MIYOSHI
Weight perturbation learning was proposed as a learning rule in which perturbation is added to the variable parameters of learning machines. The generalization performance of weight perturbation learning was analyzed by statistical mechanical methods and was found to have the same asymptotic generalization property as perceptron learning. In this paper we consider the difference between perceptron learning and AdaTron learning, both of which are well-known learning rules. By applying this difference to weight perturbation learning, we propose adaptive weight perturbation learning. The generalization performance of the proposed rule is analyzed by statistical mechanical methods, and it is shown that the proposed learning rule has an outstanding asymptotic property equivalent to that of AdaTron learning.
The induced voltage at the terminals of an implantable cardiac pacemaker of unipolar type was investigated by numerical calculations. Operating frequency was assumed 5 MHz according to a recent product. The dependencies of the induced voltage on various conditions were investigated including those on the locations of the transmitter and the pacemaker, and on the electric properties and the size of the phantom. The results showed that they were reasonably explained by considerations of quasi-static coupling of the electric field between the device and the pacemaker. Regarding the effect of electrical properties of the phantom a conservative result was obtained by using a phantom of homogeneous material with electric constants of fat. With regard to the phantom size the phantom used in previous studies provided more conservative results than that of larger size. The results suggested that the electric near-field intra-body communication devices are not likely to interfere with implantable cardiac pacemakers as far as the situation assumed in this study.
Toru SEGAWA Shinji MATSUO Takaaki KAKITSUKA Yasuo SHIBATA Tomonari SATO Yoshihiro KAWAGUCHI Yasuhiro KONDO Ryo TAKAHASHI
We present an 88 wavelength-routing switch (WRS) that monolithically integrates tunable wavelength converters (TWCs) and an 88 arrayed-waveguide grating. The TWC consists of a double-ring-resonator tunable laser (DRR TL) allowing rapid and stable switching and a semiconductor-optical-amplifier-based optical gate. Two different types of dry-etched mirrors form the laser cavity of the DRR TL, which enable integration of the optical components of the WRS on a single chip. The monolithic WRS performed 18 high-speed wavelength routing of a non-return-to-zero signal at 10 Gbit/s. The switching operation was demonstrated by simultaneously using two adjacent TWCs.
A. H. M. ALMAWGANI M. F. M. SALLEH
This paper presents a new unequal error protection (UEP) image transmission system that incorporates a Lifting Wavelet Transform (LWT) and Reed Solomon (RS) coded cooperation scheme to increase image transmission diversity, as well as save transmission bandwidth. Having a partner to assist direct communication increases the resilience of low frequency subband data against an error-prone fading channel. Low frequency subbands are partitioned into two sets of data and transmitted using the RS coded cooperation scheme. High frequency subbands data are transmitted directly to a base station. Results show that the new UEP image transmission system using LWT based RS coded cooperation scheme achieves diversity gains of around 10 dB, with channel SNR from 10 to 20 dB, compared with the image transmission system with non-cooperative system under slow Rayleigh fading channel for all levels of LWT decomposition. In addition, the new UEP image transmission system using LWT based RS coded cooperation scheme with one level of wavelet decomposition offers around 37.5% bandwidth gain (β), compared with the system without LWT, which incurs a reduction of 3 dB in reconstructed image quality.
In this paper, we propose a simple, yet effective, multiuser detection scheme for a two-hop cooperative CDMAs. In phase 1, the minimum mean square error (MMSE) detector at the destination is used to identify reliable decisions of direct transmissions from the sources and return them to the relays. Then, in phase 2, based on the reliable decisions, the relays and the destination successively utilize the maximum likelihood (ML) detectors to estimate the residual symbols. Due to the destination estimating the symbols separately from direct transmissions and the relaying signals, as a result the destination does not need the information about the relays' decision performance for the construction of the ML detector. Hence, the proposed scheme is more feasible than existing approaches for practical implementation. In addition, due to the ML detectors in phase 2 only estimating the residual symbols, the number of computations performed by the ML detectors can be reduced significantly. The results of simulations and complexity analysis demonstrate the efficiency and effectiveness of the proposed scheme.
Xuefang LIU Qinghai YANG Fenglin FU
In this letter, we investigate the Nth-best user selection scheme for amplify-and-forward cooperative systems over Rayleigh fading channels. We deduce the probability density function, the cumulative density function, and the moment generating function of the end-to-end signal-to-noise ratio of the system. Then, the respective closed-form expressions of the average symbol error probability and the outage probability at the destination are derived. The diversity order obtained in the scheme increases with user number but becomes less as the selection sequence number N increases. Simulation results verify the analytical results.
A low-complexity Reed-Solomon (RS) decoder design based on the modified Euclidean (ME) algorithm proposed by Truong is presented in this paper. Low complexity is achieved by reformulating Truong's ME algorithm using the proposed polynomial manipulation scheme so that a more compact polynomial representation can be derived. Together with the developed folding scheme and simplified boundary cell, the resulting design effectively reduces the hardware complexity while meeting the throughput requirements of optical communication systems. Experimental results demonstrate that the developed RS(255, 239) decoder, implemented in the TSMC 0.18 µm process, can operate at up to 425 MHz and achieve a throughput rate of 3.4 Gbps with a total gate count of 11,759. Compared to related works, the proposed decoder has the lowest area requirement and the smallest area-time complexity.
Ali AL-BERMANI Christian WORDEHOFF Sebastian HOFFMANN Timo PFAU Ulrich RUCKERT Reinhold NOE
We present the recovery of 2.5 Gb/s synchronous 16-point quadrature amplitude modulation data in real-time for an linewidth-times-symbol-duration ratio of 0.00048 after transmission over 1.6 km standard single mode fiber.
Masahiro KASHIWAGI Katsuhiro TAKENAGA Kentaro ICHII Tomoharu KITABAYASHI Shoji TANIGAWA Kensuke SHIMA Shoichiro MATSUO Munehisa FUJIMAKI Kuniharu HIMENO
We review our recent work on Yb-doped and hybrid-structured solid photonic bandgap fibers (Yb-HS-SPBGFs) for linearly-polarized fiber lasers oscillating in the small gain wavelength range from 1160 nm to 1200 nm. The stack-and-draw or pit-in-jacket method is employed to fabricate two Yb-HS-SPBGFs. Both of the fiber shows optical filtering property for eliminating ASE in the large gain wavelength range from 1030 nm to 1130 nm and enough high birefringence for maintaining linear polarization, thanks to the photonic bandgap effect and the induced birefringence of the hybrid structure. The fiber attenuation of the Yb-HS-SPBGF fabricated by the pit-in-jacket method is much lower than that of the Yb-HS-SPBGF fabricated by stack-and-draw method. Linearly-polarized single stage fiber lasers using Yb-HS-SPBGFs are also demonstrated. Laser oscillation at 1180 nm is confirmed without parasitic lasing in the fiber lasers. High output power and high slope efficiency in linearly-polarized single-cavity fiber laser using the low-loss Yb-HS-SPGF fabricated by the pit-in-jacket method are achieved. Narrow linewidth, high polarization extinction ratio and high beam quality are also confirmed, which are required for high-efficient frequency-doubling. A compact and high-power yellow-orange frequency-doubling laser would be realized by using a linearly-polarized single-cavity fiber laser employing a low-loss Yb-HS-SPBGF.
Takao HARA Kenta KUBO Minoru OKADA
Transmission performance of carrier superposed signals for frequency reuse are significantly degraded when transmitted through a satellite channel containing a nonlinear device. The extent to which the signals are degraded depends on the operating level (back off) of the transponder. This paper proposes a method to compensate for the effects of nonlinearity in the interference canceller by giving the same nonlinearity to a replica with the capability to automatically track the back off of the satellite transponder. Computer simulations show that the proposed technique significantly enhances system performance at all transponder operating levels even though it can be simply implemented in the canceller by digital signal processing circuits.
Daisuke KIMURA Toshimichi SAITO
This paper studies a switched dynamical system based on the boost converter with a solar cell input. The solar cell is modeled by a piecewise linear current-controlled voltage source. A variant of peak-current-controlled switching is used in the boost converter. Applying the mapping procedure, the system dynamics can be analyzed precisely. As a main result, we have found an important example of trade-off between the maximum power point and stability: as a parameter (relates to the clock period) varies, the average power of a periodic orbit can have a peak near a period-doubling bifurcation set and an unstable periodic orbit can have the maximum power point.
Dinh Thanh LE Masahiro SHINOZAWA Yoshio KARASAWA
Two designs of wideband compact MIMO antenna using printed dipoles are proposed in this paper. One is a three-port orthogonal polarization antenna and the other is a cube-six-port antenna. Measured results for the antennas show that they resonate at 2.6 GHz and support a bandwidth of over 400 MHz. The worst mutual coupling for the three-port orthogonal polarization antenna is kept under -20 dB whereas that level of the cube-six-port antenna is -18 dB. A number of experiments are conducted on MIMO systems with these compact antennas and linear antenna arrays. Measured data are analyzed to examine channel characteristics, such as cumulative distribution functions (CDFs) of eigenvalues. Furthermore, the effect of different antenna configurations on channel capacity is highlighted and discussed. A high data rate capacity can be achieved with the compact antennas, particularly from the cube-six-port variant. These antennas might be applied in actual MIMO systems in wireless communications.
Quang NGUYEN-THE Motoharu MATSUURA Hung NGUYEN TAN Naoto KISHI
We demonstrate an all-optical picosecond pulse duration-tunable nonreturn-to-zero (NRZ)-to-return-to-zero (RZ) data format conversion using a Raman amplifier-based compressor and a fiber-based four-wave mixing (FWM) switch. A NRZ data signal is injected into the fiber-based FWM switch (AND gate) with a compressed RZ clock by the Raman amplifier-based compressor, and convert to RZ data signal by the fiber-based FWM switch. The compressed RZ clock train acts as a pump signal in the fiber-based FWM switch to perform the NRZ-to-RZ data format conversion. By changing the Raman pump power of the Raman amplifier-based compressor, it is possible to tune the pulse duration of the converted RZ data signal from 15 ps to 2 ps. In all the tuning range, the receiver sensitivity at bit error rate (BER) of 10-9 for the converted RZ data signal was about 1.31.7 dB better than the receiver sensitivity of the input NRZ data signal. Moreover, the pulse pedestal of the converted RZ data signals is well suppressed owing to the FWM process in the fiber-based FWM switch.
Danish RAFIQUE Jian ZHAO Andrew D. ELLIS
We investigate electronic mitigation of linear and nonlinear fibre impairments and compare various digital signal processing techniques, including electronic dispersion compensation (EDC), single-channel back-propagation (SC-BP) and back-propagation with multiple channel processing (MC-BP) in a nine-channel 112 Gb/s PM-mQAM (m=4,16) WDM system, for reaches up to 6,320 km. We show that, for a sufficiently high local dispersion, SC-BP is sufficient to provide a significant performance enhancement when compared to EDC, and is adequate to achieve BER below FEC threshold. For these conditions we report that a sampling rate of two samples per symbol is sufficient for practical SC-BP, without significant penalties.
Chia-Hao KU Hsien-Wen LIU Yu-Shu LIN Kuei-Yi LIN Pao-Jen WANG
A planar miniaturized branch-line coupler with harmonic suppression property for UHF band applications is presented in this paper. By properly synthesizing the LC-tanks that employ artificial transmission lines, two pairs of quarter-wavelength branch-lines to respectively meet characteristic impedances of 35.4 and 50 ohms can be obtained with the coupler. For the operating band, it can achieve good 3 dB power division with a 90° phase difference in the outputs of the through and coupled arms. The coupler also has a small area of 20.5(L)18(W) mm2, corresponding to 0.11 λg0.1 λg at 922 MHz. Compared with conventional couplers, the proposed design not only offers a wide bandwidth of more than 230 MHz within 1° or 1 dB, but also works with additional harmonic suppression for achieving better performance. Therefore, the proposed branch-line coupler with a compact size is well suitable for power division application.
In optical packet switches, the overhead of reconfiguring a switch fabric is not negligible with respect to the packet transmission time and can adversely affect switch performance. The overhead increases the average waiting time of packets and worsens throughput performance. Therefore, scheduling packets requires additional considerations on the reconfiguration frequency. This work intends to analytically find the optimal reconfiguration frequency that minimizes the average waiting time of packets. It proposes an analytical model to facilitate our analysis on reconfiguration optimization for input-buffered optical packet switches with the reconfiguration overhead. The analytical model is based on a Markovian analysis and is used to study the effects of various network parameters on the average waiting time of packets. Of particular interest is the derivation of closed-form equations that quantify the effects of the reconfiguration frequency on the average waiting time of packets. Quantitative examples are given to show that properly balancing the reconfiguration frequency can significantly reduce the average waiting time of packets. In the case of heavy traffic, the basic round-robin scheduling scheme with the optimal reconfiguration frequency can achieve as much as 30% reduction in the average waiting time of packets, when compared with the basic round-robin scheduling scheme with a fixed reconfiguration frequency.