In this research, we propose an effective stability analysis method to impacting systems with periodically moving borders (periodic borders). First, we describe an n-dimensional impacting system with periodic borders. Subsequently, we present an algorithm based on a stability analysis method using the monodromy matrix for calculating stability of the waveform. This approach requires the state-transition matrix be related to the impact phenomenon, which is known as the saltation matrix. In an earlier study, the expression for the saltation matrix was derived assuming a static border (fixed border). In this research, we derive an expression for the saltation matrix for a periodic border. We confirm the performance of the proposed method, which is also applicable to systems with fixed borders, by applying it to an impacting system with a periodic border. Using this approach, we analyze the bifurcation of an impacting system with a periodic border by computing the evolution of the stable and unstable periodic waveform. We demonstrate a discontinuous change of the periodic points, which occurs when a periodic point collides with a border, in the one-parameter bifurcation diagram.

Recently, H-bridge pulse width modulation (PWM) micro-stepping motor drivers have been widely used for 3-D printers, robots, and medical instruments. Differently from a simple PWM motor driver circuit, the H-bridge PWM micro-stepping motor driver circuit can generate radio frequency (RF) electromagnetic interference (EMI) noises of up to several hundred MHz frequencies, due to digital interface circuits and a high-performance CPU. For medical instrument systems, the minimization of EMI noises can assure operating safety and greatly reduce the chance of malfunction between instruments. This work proposes a passive-filter configuration-based circuit design for reducing up-to-several-hundred-MHz EMI noises generated from the H-bridge PWM micro-stepping motor driver circuit. More specifically, the proposed RF EMI reduction approach consists of proper passive filter design, shielding in motor wires, and common ground design in the print circuit board. The proposed passive filter configuration design is validated through the overall reduction of EMI noises at RF band. Finally, the proposed EMI reduction approach is tested experientially through a prototype and about 16 dB average reduction of RF EMI noises is demonstrated.

This letter describes the development and implementation of the lane detection system accelerated by the neuromorphic hardware. Because the neuromorphic hardware has inherently parallel nature and has constant output latency regardless the size of the knowledge, the proposed lane detection system can recognize various types of lanes quickly and efficiently. Experimental results using the road images obtained in the actual driving environments showed that white and yellow lanes could be detected with an accuracy of more than 94 percent.

This study involves proposing a high-speed computer-generated hologram playback by using a digital micromirror device for high-definition spatiotemporal division multiplexing electroholography. Consequently, the results indicated that the study successfully reconstructed a high-definition 3-D movie of 3-D objects that was comprised of approximately 900,000 points at 60 fps when each frame was divided into twelve parts.

Massive amounts of computation involved in real-time evaluation of deep neural networks pose a serious challenge in battery-powered systems, and neuromorphic systems specialized in neural networks have been developed. This paper first shows the portion of active neurons at a time dwindles as going toward the output layer in recent large-scale deep convolutional neural networks. Spike-based, asynchronous neuromorphic systems take advantage of the sparse activation and reduce dynamic power consumption, while synchronous systems may waste much dynamic power even for the sparse activation due to clocks. We thus propose a clock gating-based dynamic power reduction method that exploits the sparse activation for synchronous neuromorphic systems. We apply the proposed method to a building block of a recently proposed synchronous neuromorphic computing system and demonstrate up to 79% dynamic power saving at a negligible overhead.

In this study, expressions were compared with reference material using the coaxial feed-type open-ended cut-off circular waveguide reflection method to support simple and instantaneous evaluation of dielectric constants in small amounts of scarce liquids over a broad frequency range. S11 values were determined via electromagnetic analysis for individual jig structure conditions and dielectric property values without actual S11 measurement under the condition that the tip of the measurement jig with open and short-ended conditions and with the test material inserted. Next, information on the relationships linking jig structure, dielectric properties and S11 properties was stored on a database to simplify the procedure and improve accuracy in reference material evaluation. The accuracy of the estimation formula was first theoretically verified for cases in which values indicating the dielectric properties of the reference material and the actual material differed significantly to verify the effectiveness of the proposed method. The results indicated that dielectric property values for various liquids measured at 0.5 and 1.0GHz using the proposed method corresponded closely to those obtained using the method previously proposed by the authors. The effectiveness of the proposed method was evaluated by determining the dielectric properties of certain liquids at octave-range continuous frequencies between 0.5 and 1.0GHz based on interpolation from limited data of several frequencies. The results indicated that the approach enables quicker and easier measurement to establish the complex permittivity of liquids over a broad frequency range than the previous method.

Anisotropic dielectrics and ferromagnetic materials are widely used in dispersion-engineered metamaterials. For example, nonreciprocal magnetic photonic crystals (MPhCs) are periodic structures whose unit cell is composed of two misaligned anisotropic dielectric layers and one ferromagnetic layer and they have extraordinary characteristics such as wave slowdown and field amplitude increase. We develop an unconditionally stable complex-envelop alternating-direction-implicit finite-difference time-domain method (CE-ADI-FDTD) suitable for the transient analysis of anisotropic dielectrics and ferromagnetic materials. In the proposed algorithm, the perfectly-matched-layer (PML) is straightforwardly incorporated in Maxwell's curl equations. Numerical examples show that the proposed PML-CE-ADI-FDTD method can reduce the CPU time significantly for the transient analysis of anisotropic dielectrics and ferromagnetic materials while maintaining computational accuracy.

We newly propose the first lateral mode selective active multimode interferometer laser diode. The design principle is to arrange identical propagation path of different lateral mode. Thanks to multimode waveguide structure, 0th mode and 1st order mode has individual propagation path within one device. Individual lasing of fundamental mode as well as first mode was confirmed successfully.

Arc runners are fixed on silver electrical contacts. Break arcs are generated between the contacts in a 450VDC circuit. Break arcs are magnetically blown-out and air is blown to the break arcs. The air flow was not used to our previous reports with runners. Circuit current when contacts are closed is 10A. Flow rate of air Q is changed from 1 to 10L/min. Supply voltage E is changed from 200V to 450V. The following results are shown. Arc duration D tends to decrease with increasing flow rate Q. The number of reignitions N increases with increasing supply voltage E for each flow rate Q. The number of reignitions is the least when the flow rate Q is 2L/min.

Systematic research on electromagnetic compatibility (EMC) in Japan started in 1977 by the establishment of a technical committee on “environmental electromagnetic engineering” named EMCJ, which was founded both in the Institute of Electronics and Communication Engineers or the present IEICE (Institute of Electronics, Information and Communication Engineers) and in the Institute of Electrical Engineers of Japan or the IEEJ. The research activities have been continued as the basic field of interdisciplinary study to harmonize even in the electromagnetic (EM) environment where radio waves provide intolerable EM disturbances to electronic equipment and to that environment itself. The subjects and their outcomes which the EMCJ has dealt with during about 40 years from the EMCJ establishment include the evaluation of EM environment, EMC of electric and electronic equipment, and EMC of biological effects involving bioelectromagnetics and so on. In this paper, the establishment history and structure of the EMCJ are reviewed along with the change in activities, and topics of the technical reports presented at EMCJ meetings from 2006 to 2016 are surveyed. In addition, internationalization and its related campaign are presented in conjunction with the EMCJ research activities, and the status quo of the EMCJ under the IEICE is also discussed along with the prospects.

This paper proposes a read-only memory driving circuit for RFID tags based on a-IGZO thin-film transistors. The circuit consists of a Johnson counter and monotype complementary gates. By utilizing complementary signals to drive a decoder based on monotype complementary gates, the propagation delay can be decreased and the redundant current can be reduced. The Johnson counter reduces the number of registers. The new circuit can effectively avoid glitch generation, and reduce circuit power consumption and delay.

Array antenna technology for wireless systems is highly integrated for demands such as multi-functionality and high-performance. This paper details recent technologies in Japan in design techniques based on computational electromagnetics, antenna hardware techniques in the millimeter-wave band, array signal processing to add adaptive functions, and measurement methods to support design techniques, for array antennas for future wireless systems. Prospects of these four technologies are also described.

In this paper, the effect of the tilt angle of return stroke channel and the stratified lossy ground on the lightning-induced voltages on the overhead lines are studied using the modified transmission-line model with linear current decay with height (MTLL). The results show that the lightning-induced voltages from oblique discharge channel are larger than those from the vertical discharge channel, and the peak values of the induced voltages will increase with increasing the tilt angle. When the ground is horizontally stratified, the peak of the induced voltages will increase with increasing the conductivity of the lower layer at different distances. When the upper ground conductivity increases, the voltage peak values will decrease if the overhead line is nearby the lightning strike point and increase if the overhead line is far from the lightning strike point. Moreover, the induced voltages are mainly affected by the conductivity of the lower layer soil when the conductivity of the upper layer ground is smaller than that of the lower layer ground at far distances. When the ground is vertically stratified, the induced voltages are mainly affected by the conductivity of the ground near the strike point when the overhead line and the strike point are located above the same medium; if the overhead line and the strike point are located above different mediums, both of the conductivities of the vertically stratified ground will influence the peak of the induced voltages and the conductivity of the ground which is far from the strike point has much more impact on induced voltages.

An incident response organization such as a CSIRT contributes to preventing the spread of malware infection by analyzing compromised websites and sending abuse reports with detected URLs to webmasters. However, these abuse reports with only URLs are not sufficient to clean up the websites. In addition, it is difficult to analyze malicious websites across different client environments because these websites change behavior depending on a client environment. To expedite compromised website clean-up, it is important to provide fine-grained information such as malicious URL relations, the precise position of compromised web content, and the target range of client environments. In this paper, we propose a new method of constructing a redirection graph with context, such as which web content redirects to malicious websites. The proposed method analyzes a website in a multi-client environment to identify which client environment is exposed to threats. We evaluated our system using crawling datasets of approximately 2,000 compromised websites. The result shows that our system successfully identified malicious URL relations and compromised web content, and the number of URLs and the amount of web content to be analyzed were sufficient for incident responders by 15.0% and 0.8%, respectively. Furthermore, it can also identify the target range of client environments in 30.4% of websites and a vulnerability that has been used in malicious websites by leveraging target information. This fine-grained analysis by our system would contribute to improving the daily work of incident responders.

CMOS amperometric sensors with a microelectrode array offer great potential for counting bacteria because of their low cost, compact size, and ease of use. This paper presents a current-integration-based CMOS amperometric sensor for high-sensitivity bacteria counting. It has a current integrator for noise reduction and reportedly the most large-scale microelectrode array (1024 × 1024). This proposed sensor can count the number of bacteria ranging from a single cell to approximately a million cells. A prototype chip was fabricated using two-poly three-metal (2P3M) 0.6-µm standard CMOS technology. A 7.6 × 7.1-mm2 chip operates from a 5V supply at 1.9mA. In addition, by using the prototype chip, we performed electrochemical measurement and partial 2D imaging of silicone through constant potential amperometry. The measurement results indicate that the proposed sensor chip was able to accurately readout redox current from the 1024 × 1024 sensor array.

This paper proposes a walking route recommender system aiming at continuously supporting a user to take a walk as means for health promotion. In recent years, taking a walk becomes popular with not only the elderly, but also those from all ages as one of the easiest ways for health promotion. From the viewpoint of health promotion, it is desirable to take a walk as daily exercise. However, walking is very simple activity, which makes it difficult for people to maintain their motivation. Although using an activity monitor is expected to improve the motivation for taking a walk as daily exercise, it forces users to manage their activities by themselves. The proposed system solves such a problem by recommending a walking route that can consume target calories. When a system is to be used for long period of time for supporting user's daily exercise, it should consider the case when a user will not follow the recommended route. It would cause a gap between consumed and target calories. We think this problem becomes serious when a user gradually gets bored with taking a walk during a long period of time. In order to solve the problem, the proposed method implicitly manages calories on monthly basis and recommends walking routes that could keep a user from getting bored. The effectiveness of the recommendation algorithm is evaluated with agent simulation. As another important factor for walking support, this paper also proposes a navigation interface that presents direction to the next visiting point without using a map. As users do not have to continuously focus on the interface, it is not only useful for their safety, but also gives them room to enjoy the landscape. The interface is evaluated by an experiment with test participants.

An optical intensity distribution under light irradiation in the organic photovoltaic cell affects the absorbance of the active layer, which determines the photovoltaic performance. In this research, we evaluated the optimum thickness of the organic active layer with poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b;4,5-b']dithiophene-2,6-diyl-alt-(4-(2-ethylhexyl)-3-fluorothieno[3,4-b]thiophene-)-2-carboxylate-2-6-diyl)] and [6,6]-phenyl C71-butyric acid methyl ester. The spectral response of external quantum efficiency was good agreement with the simulated optical intensity distribution within a device stack as a function of the position and the wavelength. As a result, the highest photoconversion efficiency of 10.1% was achieved for the inverted device structure.

For phase stabilization of two-tone coherent millimeter-wave/microwave carrier generation, two types of phase detection schemes were devised based on lightwave interferometric technique, the Mach-Zehnder interferometric method and the pseudo Mach-Zehnder interferometric method. The former system showed clear eye patterns at both OOK and PSK modulations of 1 Gbit/s on the 12.5-GHz carrier. The latter system demonstrated the error-free transmission at OOK modulation of 11 Gbit/s on the 100-GHz carrier.

Silver electrical contacts are separated at constant speed and break arcs are generated between them in a 200V-450VDC and 10A resistive circuit. The motion of the break arcs is restricted by some surrounding alumina plates. Transverse magnetic field of a permanent magnet is applied to the break arcs. Changing the supply voltage and the height of a wall located at the upper side of the break arcs, the arc lengthening time and motion of the break arcs are investigated. As a result, the higher supply voltage causes an increase of the arc lengthening time. The arc lengthening time increases significantly when the break arcs expand into the whole of the surrounding walls.

This paper describes a numerical assessment methodology of pacemaker EMI triggered by HF-band wireless power transfer system. By using three dimensional full-wave numerical simulation based on finite element method, interference voltage induced at the connector of the pacemaker inside the phantom that is used for in-vitro EMI assessment is obtained. Simulated example includes different exposure scenarios in order to estimate the maximum interference voltage.