To provide basic considerations for the realization of method for suppressing the EMI from differential-paired lines on flexible printed circuits (FPC), the characteristics of the SI performance and shielding effectiveness (SE) of shielded-flexible printed circuits for differential-signaling are investigated in this paper experimentally and by a numerical modeling. Firstly, transmission characteristics of TDR measurement and frequency response of |Sdd21| are discussed, from view point of signal integrity. Secondly, as the characteristics of the SE performance for EMI, frequency responses of magnetic field are investigated. Although placement of conductive shield near the paired-lines decreases characteristics impedance, |Sdd21| for the “with Cu 5.5 µm-thickness copper shield” is not deteriorated compared with “without shield” and sufficient SE performance for magnetic field can be established. But, thin-shield deteriorates SI as well as SE performances. The frequency response of |Sdd21| at higher frequencies for the “Ag 0.1 µm” case has the steep loss roll off. A reflection loss resulted from impedance-mismatching is not dominant factor of the losses. The dominant factor may be magnetic field leakage due to very thin-conductive shield.

The analytic expressions of lightning electromagnetic fields generated by tortuous channel with an inclined lower section are obtained by decomposing the current infinitesimal and solving Maxwell's equations. By using the transmission line model and pulse function to express the channel-base current, the influence of length and tilt angle of the oblique part on lightning electromagnetic fields as well as the distribution laws of electromagnetic fields for different azimuth angles are analyzed. The results show that the electromagnetic fields in near area are mainly determined by the lower section of the tortuous discharge channel, and the peak values of electromagnetic fields in different field regions will increase with the increasing of the length of the lower section when L1 is shorter than the distance that return-stroke speed multiplied by peak time. Whereas the length of the lower section is longer than the distance that return-stroke speed multiplied by peak time, the waveforms of electromagnetic fields will overlap each other and won't be influenced by oblique part length of the discharge channel before the return-stroke current arrives at the inflection point. Moreover, the peak values of electromagnetic fields will decrease with the increase of tilt angle (the azimuth angle φ = 2π/3) and azimuth angle, and the impact of channel geometry on the electromagnetic field strengthens with the distance.

Pre-Cantor bar, the one-dimensional fractal media, consists of two kinds of materials. Using the transmission-line theory we will explain the double-exponential behavior of the minimum of the transmittance as a function of the stage number n, and obtain formulae of two kinds of scaling behaviors of the transmittance. From numerical calculations for n=1 to 5 we will find that the maximum of field amplitudes of resonance which increases double-exponentially with n is well estimated by the theoretical upper bound. We will show that after sorting field amplitudes for resonance frequencies of the 5th stage their distribution is a staircase function of the index.

A triplexer is presented by using bandpass filters (BPFs) which consist of two-stage of wideband resonator and additional open-circuited stubs. The resonator is firstly proposed by using a coupled-line and an inductive element loaded transmission line. This resonator produces the wide passband by a dual-mode resonance, high attenuation level at stopbands, and the steepness at the edge of the passband due to the attenuation poles. In order to understand the behavior of the resonator, the conditions for resonances and attenuation poles are especially solved and their current densities are analyzed by an electromagnetic simulation. Secondly, three types of wideband BPFs are constituted and finally a wideband triplexer is composed by using these BPFs. The basic characteristics of the proposed BPFs and the matching methodology enable to realize the triplexer whose desired passbands are around 3.1-5.1 GHz, 5.85-7.85 GHz, and 8.6-10.6 GHz with high isolation performance at the other passbands. The proposed triplexer is predominance in the flexible bandwidth or wide operating frequency range. All the BPFs and the triplexer are implemented on a planar printed circuit board assuming the use of the microstrip line structure.

In this paper we propose a novel classification method for the multiple k-nearest neighbor (MkNN) classifier and show its practical application to medical image processing. The proposed method performs fine classification when a pair of the spatial coordinate of the observation data in the observation space and its corresponding feature vector in the feature space is provided. The proposed MkNN classifier uses the continuity of the distribution of features of the same class not only in the feature space but also in the observation space. In order to validate the performance of the present method, it is applied to the tissue characterization problem of coronary plaque. The quantitative and qualitative validity of the proposed MkNN classifier have been confirmed by actual experiments.

In this study, a well-shaped microelectrode array (MEA) for fabricating a high-density complementary metal-oxide semiconductor amperometric electrochemical sensor array was designed and verified. By integrating an auxiliary electrode with the well-shaped structure of the MEA, the footprint was reduced and high density and high resolution were also achieved. The results of three-dimensional electrochemical simulations confirmed the effectiveness of the proposed MEA structure and possibility of increasing the density to four times than that achieved by the conventional two-dimensional structure.

In this paper, a vehicular antenna design scheme that considers vehicular body effects is proposed. A wire antenna for the global positioning system (GPS) and long-term evolution (LTE) systems is implemented on a plastic plate and then mounted on a windshield of the vehicle. Common outputs are used to allow feed sharing. It is necessary to increase the GPS right-hand circularly polarization (RHCP) gain near the zenith and to reduce the axis ratio (AR). For LTE, we need to increase the horizontal polarization (HP) gain. In addition, for LTE, multiband characteristics are required. In order to achieve the specified performance, the antenna shape is optimized via a Pareto genetic algorithm (PGA). When an antenna is mounted on the body, antenna performance changes significantly. To evaluate the performance of an antenna with complex shape mounted on a windshield, a commercial electromagnetic simulator (Ansoft HFSS) is used. To apply electromagnetic results output by HFSS to the PGA algorithm operating in the MATLAB environment, a MATLAB-to-HFSS linking program via Visual BASIC (VB) script was used. It is difficult to carry out the electromagnetic analysis on the entire body because of the limitations of the calculating load and memory size. To overcome these limitations, we consider only that part of the vehicle's body that influences antenna performance. We show that a series of optimization steps can minimize the degradation caused by the vehicle`s body. The simulation results clearly show that it is well optimized at 1.575GHz for GPS, and 0.74 ∼ 0.79GHz and 2.11 ∼ 2.16GHz for LTE, respectively.

Accidental falling among elderly people has become a public health concern. Thus, there is a need for systems that detect a fall when it happens. This paper presents a portable real-time remote health monitoring system that can remotely monitor patients' movements. The system is designed and implemented using ZigBee wireless technologies, and the data is analysed using Matlab. The purpose of this research is to determine the acceleration thresholds for fall detection, using tri-axial accelerometer readings at the head, waist, and knee. Seven voluntary subjects performed purposeful falls and Activities of Daily Living (ADL). The results indicated that measurements from the waist and head can accurately detect falls; the sensitivity and reliability measurements of fall detection ranged between 80% and 90%. In contrast, the measurements showed that the knee is not a useful position for the fall detection.

Because redox sensors can detect multi-ions and the concentration within a single sensing area using current and potential signals, they have been studied for chemical analysis applications. A small sensing area and a low concentration measurement typically reduce the output current of a redox sensor. Therefore, we previously fabricated the Amplified Redox Sensor, which has a working electrode combined with a bipolar transistor to amplify a small current signal. However, the current gain of the bipolar transistor had been changed by the redox current because the redox current flows in the base terminal of the bipolar transistor. In this study, we propose a new measurement method in which an offset current is inserted along with the redox current in the base terminal. The proposed measurement method can detect potassium ferricyanide (K3[Fe (CN)6]) concentrations as low as 1μM using the Square Wave Voltammetry method.

Microwave systems have a number of promising applications in surveillance and monitoring systems. The main advantage of microwave systems is their ability to detect targets at distance under adverse conditions such as dim, smoky, and humid environments. Specifically, the wide bandwidth of ultra-wideband radar enables high range resolution. In a previous study, we proposed an accurate shape estimation algorithm for multiple targets using multiple ultra-wideband Doppler interferometers. However, this algorithm produces false image artifacts under conditions with severe interference. The present paper proposes a technique to suppress such false images by detecting inconsistent combinations of the radial velocity and time derivative of image positions. We study the performance of the proposed method through numerical simulations of a two-dimensional section of a moving human body, and demonstrate the remarkable performance of the proposed method in suppressing false image artifacts in many scenarios.

We propose a new swept-frequency measurement method for the electromagnetic characterization of materials. The material is a multilayer cylinder that pierces a rectangular waveguide through two holes in the narrow waveguide walls. The complex permittivity and permeability of the material are calculated from measured S-parameters as an inverse problem. To this aim, the paper develops a complete electromagnetic formulation of the problem, where the effects of material insertion holes are taken into consideration. The formulation is validated through the measurement of ferrite and water samples in the S-band.

It has been reported that a left-handed waveguide can be constituted using cutoff TE10 mode of rectangular waveguide. Because the cutoff TE10 mode shows effectively negative permittivity, the left-handed mode propagates by adding series capacitance in the form of short- or open-stubs. This paper suggests a constitution method of left-handed waveguides using cutoff TM mode. In this case, the cutoff TM mode shows effectively negative permeability. Therefore, a left-handed waveguide can be constituted by adding parallel inductance. In this paper, two types of the left-handed waveguides are designed using circular TM01 mode and rectangular TM11 mode, and the dispersion characteristics are numerically investigated. The validity of the constituting principle is confirmed by an experiment.

Cassuto and Blaum proposed new error correcting codes which are called symbol-pair codes. They presented a coding framework for channels whose outputs are overlapping pairs of symbols in storage applications. Such channels are called symbol-pair read channels. The pair distance and pair error are used in symbol-pair read channels. Cassuto et al. and Yaakobi et al. presented decoding algorithms for symbol-pair codes. However, their decoding algorithms cannot always correct errors whose number is not more than half the minimum pair distance. In this paper, we propose a new decoding algorithm using syndromes of symbol-pair codes. In addition, we show that the proposed algorithm can correct all pair errors within the pair error correcting capability.

The harmonious coloring of an undirected simple graph is a vertex coloring such that adjacent vertices are assigned different colors and each pair of colors appears together on at most one edge. The harmonious chromatic number of a graph is the least number of colors used in such a coloring. The harmonious chromatic number of a path is known, whereas the problem to find the harmonious chromatic number is NP-hard even for trees with pathwidth at most 2. Hence, we consider the harmonious coloring of trees with pathwidth 1, which are also known as caterpillars. This paper shows the harmonious chromatic number of a caterpillar with at most one vertex of degree more than 2. We also show the upper bound of the harmonious chromatic number of a 3-regular caterpillar.

A new algorithm for separating mass spectra into individual substances for explosives detection is proposed. In the field of mass spectrometry, separation methods, such as principal-component analysis (PCA) and independent-component analysis (ICA), are widely used. All components, however, have no negative values, and the orthogonality condition imposed on components also does not necessarily hold in the case of mass spectra. Because these methods allow negative values and PCA imposes an orthogonality condition, they are not suitable for separation of mass spectra. The proposed algorithm is based on probabilistic latent-component analysis (PLCA). PLCA is a statistical formulation of non-negative matrix factorization (NMF) using KL divergence. Because PLCA imposes the constraint of non-negativity but not orthogonality, the algorithm is effective for separating components of mass spectra. In addition, to estimate the components more accurately, a sparsity constraint is applied to PLCA for explosives detection. The main contribution is industrial application of the algorithm into an explosives-detection system. Results of an experimental evaluation of the algorithm with data obtained in a real railway station demonstrate that the proposed algorithm outperforms PCA and ICA. Also, results of calculation time demonstrate that the algorithm can work in real time.

A new algorithm for separating mass spectra into individual substances is proposed for explosives detection. The conventional algorithm based on probabilistic latent component analysis (PLCA) is effective in many cases because it makes use of the fact that non-negativity and sparsity hold for mass spectra in explosives detection. The algorithm, however, fails to separate mass spectra in some cases because uncertainty can not be resolved only by non-negativity and sparsity constraints. To resolve the uncertainty, an algorithm based on shift-invariant PLCA (SIPLCA) utilizing temporal correlation of mass spectra is proposed in this paper. In addition, to prevent overfitting, the temporal correlation is modeled with a function representing attenuation by focusing on the fact that the amount of a substance is attenuated continuously and slowly with time. Results of an experimental evaluation of the algorithm with data obtained in a real railway station demonstrate that the proposed algorithm outperforms the PLCA-based conventional algorithm and the simple SIPLCA-based one. The main novelty of this paper is that an evaluation of the detection performance of explosives detection is demonstrated. Results of the evaluation indicate that the proposed separation algorithm can improve the detection performance.

This paper proposes and analyses an improved direction finding (DF) method that uses a rotating interferometer. The minimum sampling frequency is deduced in order to eliminate the phase ambiguity associated with a long baseline, the influence of phase imbalance of receiver is quantitatively discussed and the Root Mean Square Error (RMSE) of both bearing angle and pitch angle are also demonstrated. The theoretical analysis of the rotating interferometer is verified by simulation results, which show that it achieves better RMSE performance than the conventional method.

Copper arc runners are fixed on silver electrical contacts. Break arcs are generated between the contacts in a DC resistive circuit. Circuit current when contacts are closed is 10A. Supply voltage is changed from 200V to 450V. The following results are shown. Cathode spots stay on the cathode surface but anode spots run on the runner when the supply voltage is 250V and over. In cases of the supply voltage is greater than 250V, the break arcs run on the runner when the arcs are successfully extinguished, and stays on the runner in cases of the failure of arc extinction. The arc lengths just before arc extinction with or without the runners are also investigated. The arc lengths are the same with or without the runners for each supply voltage.

In this study, we propose a two-step approach to evaluate electromagnetic interference (EMI) with a wearable vital signal sensor. The two-step approach combines a quasi-static electromagnetic (EM) field analysis and an electric circuit analysis, and is applied to the EMI evaluation at frequencies below 1 MHz for our developed wearable electrocardiogram (ECG) to demonstrate its usefulness. The quasi-static EM field analysis gives the common mode voltage coupled from the incident EM field at the ECG sensing electrodes, and the electric circuit analysis quantifies a differential mode voltage at the differential amplifier output of the ECG detection circuit. The differential mode voltage has been shown to come from a conversion from the common mode voltage due to an imbalance between the contact impedances of the two sensing electrodes. When the contact impedance is resistive, the induced differential mode voltage increases with frequency up to 100kHz, and keeps constant after 100kHz, i.e., exhibits a high pass filter characteristic. While when the contact impedance is capacitive, the differential mode voltage exhibits a band pass filter characteristic with the maximum at frequency of around 150kHz. The differential voltage may achieve nearly 1V at the differential amplifier output for an imbalance of 30% under 10V/m plane-wave incident electric field, and completely mask the ECG signal. It is essential to reduce the imbalance as much as possible so as to prevent a significant interference voltage in the amplified ECG signal.

Ultra high definition (UHD) imaging systems have attracted much attention as a next generation television (TV) broadcasting service and video streaming service. However, the state of the art video coding standards including H.265/HEVC has not enough compression rate for streaming, broadcasting and storing UHD. Existing coding standard such as H.265/HEVC normaly use RGB-YCbCr color transform before compressing RGB color image since that procedure can decorrelate color components well. However, there is room for improvement on the coding efficiency for color image based on an observation that the luminance and chrominance components changes in same locations. This observation inspired us to propose a new post-processing method for compressed images by using weighted least square (WLS) filter with coded luminance component as a guide image, for refining the edges of chrominance components. Since the computational cost of WLS tends to superlinearly increase with increasing image size, it is difficult to apply it to UHD images. To overcome this problem, we propose slightly overlapped block partitioning and a new variant of WLS (constrained WLS, CWLS). Experimental results of objective quality comparison and subjective assessment test using 4K images show that our proposed method can outperform the conventional method and reduce the bit amount for chrominance component drastically with preserving the subjective quality.