Delay models for binary logic circuits have been proposed and clarified their mathematical properties. Kleene's ternary logic is one of the simplest delay models to express transient behavior of binary logic circuits. Goto first applied Kleene's ternary logic to hazard detection of binary logic circuits in 1948. Besides Kleene's ternary logic, there are many delay models of binary logic circuits, Lewis's 5-valued logic etc. On the other hand, multiple-valued logic circuits recently play an important role for realizing digital circuits. This is because, for example, they can reduce the size of a chip dramatically. Though multiple-valued logic circuits become more important, there are few discussions on delay models of multiple-valued logic circuits. Then, in this paper, we introduce a delay model of multiple-valued logic circuits, which are constructed by Min, Max, and Literal operations. We then show some of the mathematical properties of our delay model.

This paper presents an approach to implementing simulation models for SAM fuzzy controllers without the use of external components. The approach represents a fuzzy controller as a composition of simple simulation models which involve only basic operations.

In this paper, we propose a new differential MIMO single-carrier system with frequency-domain equalization (SC-FDE) aided by the insertion of cyclic prefix. This block transmission system not only inherits all the merits of the SISO SC-FDE system, but is also equipped with a differential space-time block coding (DSTBC) such as to combat the fast-changing frequency selective fading channels without the needs to estimate and then compensate the channel effects. Hence, for practical applications, it has the additional merits of decoding simplicity and robustness against high mobility transmission environments. Computer simulations show that the proposed system can provide diversity benefit as the non-differential system does, while greatly reducing the receiver complexity.

An analog pre-distortion linearizer employing a radio frequency (RF) transistor with a self base bias control circuit is proposed. The self base bias control circuit extracts the envelope from the modulated input RF signal of the RF transistor and automatically controls its base current according to the extracted envelope. As a result, the proposed linearizer realizes positive gain deviation at high input power level. By adding a resistor between the RF transistor and the self base bias control circuit, the negative gain deviation can be derived. The design of the proposed lineaizer is described with taking the envelope frequency response of the self base bias control circuit into consideration. The fabricated linearizer achieves the adjacent channel power leakage ratio (ACLR) improvement of 8.1 dB for a 2 GHz-band, 10 W-class GaAs FET high-power amplifier (HPA) with negative gain deviation for W-CDMA base stations. It also achieves the ACLR improvement of 8.3 dB for a LDMOS HPA with positive gain deviation for the same application.

Generalized selection combining (GSC) was recently proposed as a low-complexity diversity combining technique for diversity-rich environments. This letter proposes a multi-hop Decode-and-Forward Relaying (MDFR) scheme in conjunction with GSC and describes its performance in terms of average bit error probability. We have shown that the proposed protocol offers a remarkable diversity advantage over direct transmission as well as the conventional decode-and-forward relaying (CDFR) scheme. Simulation results are also given to verify the analytical results.

In this paper, a novel CMA (constant modulus algorithm) algorithm employing fast convolution in the DFT (discrete Fourier transform) domain is proposed. We propose a non-linear adaptation algorithm that minimizes CMA cost function in the DFT domain. The proposed algorithm is completely new one as compared to the recently introduced similar DFT domain CMA algorithm in that, the original CMA cost function has not been changed to develop DFT domain algorithm, resulting improved convergence properties. Using the proposed approach, we can reduce the number of multiplications to O(Nlog2 N), whereas the conventional CMA has the computation order of O(N2). Simulation results show that the proposed algorithm provides a comparable performance to the conventional CMA.

A novel broad-band ring-slot array antenna for simultaneous use of orthogonal polarizations is presented in this paper. In this antenna, the broad-band performance is obtained by integrating a 22 ring-slot array antenna and a broad-band π/2 hybrid circuit. The simultaneous use of the right-hand circular polarization (RHCP) and the left-hand circular polarization (LHCP) is achieved using orthogonal feed circuits on three layers. The both-sided MIC technology is effectively employed in forming this type of slot array antenna. Experimental results show that the proposed antenna has good circular polarization characteristics for both the LHCP and the RHCP. The measured impedance-bandwidth of return loss better than -10 dB are about 47% both for the LHCP and the RHCP. The 3 dB axial ratio bandwidths are 25% (RHCP) and 29% (LHCP). The isolation between the two input ports is better than -35 dB at center frequency of 7.5 GHz.

In this paper, we studied the use of common-mode noise reduction technique for in-vehicle electronic equipment in an actual instrument design. We have improved the circuit model of the common-mode noise that flows to the wire harness to add the effect of a bypass capacitor located near the LSI. We analyzed the improved circuit model using a circuit simulator and verified the effectiveness of the noise reduction condition derived from the circuit model. It was also confirmed that offsetting the impedance mismatch in the PCB section requires to make a circuit constant larger than that necessary for doing the impedance mismatch in the LSI section. An evaluation circuit board comprising an automotive microcomputer was prototyped to experiment on the common-mode noise reduction effect of the board. The experimental results showed the noise reduction effect of the board. The experimental results also revealed that the degree of impedance mismatch in the LSI section can be estimated by using a PCB having a known impedance. We further inquired into the optimization of impedance parameters, which is difficult for actual products at present. To satisfy the noise reduction condition composed of numerous parameters, we proposed a design method using an optimization algorithm and an electromagnetic field simulator, and confirmed its effectiveness.

This paper presents a novel spur suppression technique using a three-phase holding pulse for a direct digital synthesizer (DDS) with a two-phase holding digital-to-analog converter (2PH-DAC). A 2PH-DAC, which uses a reverse-sign step-function as a sampling pulse waveform instead of a commonly-used gate function of zeroth-order hold, enhances the first image of aliasing, which is of higher frequency than the fundamental. Therefore, the first image can be treated as a desired signal, while the fundamental and the second image are spurs for a DDS with a 2PH-DAC (2PH-DDS). The main problem of the 2PH-DDS is close spurs in the case that signal frequency is near Nyquist frequency or sampling frequency. This paper proposes a novel spur suppression technique for a 2PH-DDS. A configuration of a 2PH-DDS is first explained, and spectral properties are analyzed. Based on the analysis, a technique using a three-phase holding pulse to cancel spurs is proposed. Evaluated spur levels of the proposed synthesizer are from -51 to -34 dBc, and are improved by 25 dB or more by the proposed technique.

Various types of optical connector with a precise alignment mechanism and long-term reliability have been researched, developed and improved during about 30 years since practical optical communication systems were first introduced in Japan in 1981. The main issues related to optical fiber connector development changed from performance improvement to miniaturization, cost reduction and ease of field assembly when optical communication systems expanded from optical trunk networks to optical access networks. Various different key technologies for optical connectors have been developed to meet these requirements, and a large number of optical connectors are currently being used for the flexible and efficient construction, maintenance and operation of optical access networks. This paper describes the structure, features, and basic technologies of the optical connectors employed in optical access networks in Japan and their standardization and future prospects.

In this research, we focus on how to track a target region that lies next to similar regions (e.g. a forearm and an upper arm) in zoom-in images. Many previous tracking methods express the target region (i.e. a part in a human body) with a single model such as an ellipse, a rectangle, and a deformable closed region. With the single model, however, it is difficult to track the target region in zoom-in images without confusing it and its neighboring similar regions (e.g. "a forearm and an upper arm" and "a small region in a torso and its neighboring regions") because they might have the same texture patterns and do not have the detectable border between them. In our method, a group of feature points in a target region is extracted and tracked as the model of the target. Small differences between the neighboring regions can be verified by focusing only on the feature points. In addition, (1) the stability of tracking is improved using particle filtering and (2) tracking robust to occlusions is realized by removing unreliable points using random sampling. Experimental results demonstrate the effectiveness of our method even when occlusions occur.

A scheme that jointly estimates carrier frequency offset and channel is proposed for the orthogonal frequency division multiplexing (OFDM) system. In the proposed scheme, the carrier frequency offset (CFO) and the channel state information (CSI) are first estimated by an minimum mean square error (MMSE) estimator and an maximum likelihood (ML) estimator, respectively. By exchanging the estimation information between these two estimators, the final estimation of CFO and CSI is then obtained by an iterative method. In the iterative process, the effect of imperfect CSI is considered. It can improve the estimation precision for a shorter preamble and accelerate the iterative convergence rate. To reduce the complexity of the proposed scheme, a procedure is adopted to eliminate the inverse operation of covariance matrix that is recalculated at each iteration. In addition, a sufficient condition for the convergence of the proposed method is deduced. The numerical simulation results show that the BER performance of our scheme is better than that of joint MLE for a shorter preamble and is comparable to that of joint MLE for a longer preamble. Furthermore, the average iterative time of our method is reduced by half as compared to the MLE methods without considering the effect of imperfect CSI.

We present a full description of a polarization-independent athermal differential quadrature phase shift keying (DQPSK) demodulator that employs silica-based planar lightwave circuit (PLC) technology. Silica-based PLC DQPSK demodulator has good characteristics including low polarization dependence, mass producibility, etc. However delay line interferometer (DLI) of demodulator had the large temperature dependence of its optical characteristics, so it required large power consumption to stabilize the chip temperature by the thermo-electric cooler (TEC). We previously made a quick report about an athermal DLI to reduce a power consumption by removing the TEC. In this paper, we focus on the details of the design and the fabrication method we used to achieve the athermal characteristics, and we describe the thermal stability of the signal demodulation and the reliability of our demodulator. We described two athermalization methods; the athermalization of the transmission spectrum and the athermalization of the polarization property. These methods were successfully demonstrated with keeping a high extinction ratio and a small footprint by introducing a novel interwoven DLI configuration. This configuration can also limit the degradation of the polarization dependent phase shift (PDf) to less than 1/10 that with the conventional configuration when the phase shifters on the waveguide are driven. We used our demodulator and examined its demodulation performance for a 43 Gbit/s DQPSK signal. We also verified its long-term reliability and thermal stability against the rapid temperature change. As a result, we confirmed that our athermal demodulator performed sufficiently well for use in DQPSK systems.

We propose a randomness test based on the T-complexity of a sequence, which can be calculated using a parsing algorithm called T-decomposition. Recently, the Lempel-Ziv (LZ) randomness test based on LZ-complexity using the LZ78 incremental parsing was officially excluded from the NIST test suite in NIST SP 800-22. This is caused from the problem that the distribution of P-values for random sequences of length 106 is strictly discrete for the LZ-complexity. Our proposed test can overcome this problem because T-complexity has almost ideal continuous distribution of P-values for random sequences of length 106. We also devise a new sequential T-decomposition algorithm using forward parsing, while the original T-decomposition is an off-line algorithm using backward parsing. Our proposed test can become a supplement to NIST SP 800-22 because it can detect several undesirable pseudo-random numbers that the NIST test suite almost fails to detect.

This paper applies the Evolutionary Programming (EP) algorithm and a risk assessment technique to obtain an optimal solution to the Unit Maintenance Scheduling Decision (UMSD) problem subject to economic cost and power security constraints. The proposed approach employs a risk assessment model to evaluate the security of the power supply system and uses the EP algorithm to establish the optimal unit maintenance schedule. The effectiveness of the proposed methodology is verified through testing using the IEEE Reliability Test System (RTS). The test results confirm that the proposed approach can to ensure that the system security and outperforms the existing deterministic and stochastic optimization methods both in terms of the quality of the solution and the computational effort required. Therefore, the proposed methodology represents a particular effective technique for the UMSD.

In this paper, an evaluation method for electromagnetic wave absorber with anisotropic reflection properties is discussed. Anisotropic absorber panels have an axis of anisotropy (principal axis). In order to specify the principal axis, the evaluation method based on the diagonalization of reflection coefficient matrix is used. Also, the permittivity of absorber materials is considered.

This paper treats a band-broadening design technique of a dual-band branch-line coupler with matching networks composed of an impedance step and a short-circuited stub based on the equivalent admittance approach. By replacing each right-handed transmission line (RH-TL) with a composite right/left-handed transmission line (CRLH-TL), very flat couplings over a relative bandwidth of about 10% can be obtained at two arbitrary operating frequencies in comparison with previous CRLH-TLs branch-line couplers. Furthermore, by adding periodical open-circuited stubs into RH-TLs of the designed CRLH-TLs branch-line coupler with matching networks, the entire size of the coupler can be reduced to about 50%. Verification of these band-broadening and size-reduction design techniques can be also shown by an electromagnetic simulation and experiment.

A method to realize the fine frequency-tuning steps using tiny capacitors instead of Metal-Insulator-Metal (MIM) capacitors is proposed for a digitally controlled oscillator (DCO). The tiny capacitors are realized by the coplanar transmission lines which are arranged unsymmetrical in a 6 metal layers (M6) foundry of 0.18 µm CMOS technology. These transmission line based capacitors are designed by using electro-magnetic field simulator, and co-designed by using SPICE simulator. Finally, these capacitors are employed to design 15 bit DCO and fabricated the proposed DCO in 0.18 µm CMOS technology, and tested. The measured phase noise of DCO was -118.3 dBc/Hz (@1 MHz offset frequency), and the oscillating frequency tuned from 4.86 GHz to 5.36 GHz in the minimum frequency-tuning step of 18 kHz.

The use of image contrast enhancement has become increasingly essential due to the need to better show the visual information contained within the image for all vision-based systems. This has lead to motivation for the design of a powerful and accurate automatic contrast enhancement for a digital image. Histogram equalization is the most commonly used contrast enhancement method. However, the conventional histogram equalization methods usually result in excessive contrast enhancement, which causes the unnatural look and visual artifacts of the processed image. In this paper, we propose a novel histogram equalization method using the automatic histogram separation along with the piecewise transformed function. The contrast enhancement results of the proposed method were not only analyzed through qualitative visual inspection and for quantitative accuracy, but are also compared to the results of other state-of-the-art methods.

Error-propagation is an important issue and should be carefully coped with in the decision-feedback equalizers (DFE). Ignoring the impact of error-propagation often leads to impractical laboratory results. In this paper, we investigate two novel layered space-frequency equalizers (LSFE) for single-carrier multiple-input multiple-output (MIMO) systems, where the recently proposed frequency-domain equalizer with time domain noise-predictor (FDE-NP) is adopted at each stage of the LSFE. We first derive the partially-connected LSFE with noise predictor (PC-LSFE-NP) which has exactly the same mean square error (MSE) as the conventional LSFE under the assumption of perfect feedback. However, if error-propagation is considered, the proposed PC-LSFE-NP can achieve better performance than the conventional LSFE due to the more reliable feedback output by the decoders. To reduce the interference from the not yet detected layers in the feedback section, we then introduce the fully-connected LSFE with noise predictor (FC-LSFE-NP), in which all layers are implicitly equalized within each stage and their decisions fed back internally. The powerful feedback filter of FC-LSFE-NP brings significant performance superiority over the conventional LSFE and PC-LSFE-NP with either perfect or imperfect feedback. Moreover, we propose a simple soft-demapper for the equalizers to avoid information loss during decoding, and thus, further improve the performance. Finally, we compare the performance of (PC/FC)-LSFE-NP with the existing schemes by computer simulations.