With the recent commercialization of fifth-generation mobile communication systems (5G), wireless communications are being used in various fields. Accordingly, the number of situations in which sensitive information, such as personal data is handled in wireless communications is increasing, and so is the demand for confidentiality. To meet this demand, we proposed a chaos-based radio-encryption modulation that combines physical layer confidentiality and channel coding effects, and we have demonstrated its effectiveness through computer simulations. However, there are no demonstrations of performances using real signals. In this study, we constructed a transmission system using Universal Software Radio Peripheral, a type of software-defined radio, and its control software LabVIEW. We conducted wired transmission experiments for the practical use of radio-frequency encrypted modulation. The results showed that a gain of 0.45dB at a bit error rate of 10-3 was obtained for binary phase-shift keying, which has the same transmission efficiency as the proposed method under an additive white Gaussian noise channel. Similarly, a gain of 10dB was obtained under fading conditions. We also evaluated the security ability and demonstrated that chaos modulation has both information-theoretic security and computational security.

Intelligent traffic monitoring provides information support for autonomous driving, which is widely used in intelligent transportation systems (ITSs). A method for estimating vehicle moving target parameters based on millimeter-wave radars is proposed to solve the problem of low detection accuracy due to velocity ambiguity and Doppler-angle coupling in the process of traffic monitoring. First of all, a MIMO antenna array with overlapping elements is constructed by introducing them into the typical design of MIMO radar array antennas. The motion-induced phase errors are eliminated by the phase difference among the overlapping elements. Then, the position errors among them are corrected through an iterative method, and the angle of multiple targets is estimated. Finally, velocity disambiguation is performed by adopting the error-corrected phase difference among the overlapping elements. An accurate estimation of vehicle moving target angle and velocity is achieved. Through Monte Carlo simulation experiments, the angle error is 0.1° and the velocity error is 0.1m/s. The simulation results show that the method can be used to effectively solve the problems related to velocity ambiguity and Doppler-angle coupling, meanwhile the accuracy of velocity and angle estimation can be improved. An improved algorithm is tested on the vehicle datasets that are gathered in the forward direction of ordinary public scenes of a city. The experimental results further verify the feasibility of the method, which meets the real-time and accuracy requirements of ITSs on vehicle information monitoring.

Physical Unclonable Function (PUF) is a promising lightweight hardware security primitive that can extract device fingerprints for encryption or authentication. However, extracting fingerprints from either the chip or the board individually has security flaws and cannot provide hardware system-level security. This paper proposes a new Chip-PCB hybrid PUF(CPR PUF) in which Weak PUF on PCB is combined with Strong PUF inside the chip to generate massive responses under the control of challenges of on-chip Strong PUF. This structure tightly couples the chip and PCB into an inseparable and unclonable unit thus can verify the authenticity of chip as well as the board. To improve the uniformity and reliability of Chip-PCB hybrid PUF, we propose a lightweight key generator based on a reliability self-test and debiasing algorithm to extract massive stable and secure keys from unreliable and biased PUF responses, which eliminates expensive error correction processes. The FPGA-based test results show that the PUF responses after robust extraction and debiasing achieve high uniqueness, reliability, uniformity and anti-counterfeiting features. Moreover, the key generator greatly reduces the execution cost and the bit error rate of the keys is less than 10-9, the overall security of the key is also improved by eliminating the entropy leakage of helper data.

Automatic modulation recognition(AMR) of radar signals is a currently active area, especially in electronic reconnaissance, where systems need to quickly identify the intercepted signal and formulate corresponding interference measures on computationally limited platforms. However, previous methods generally have high computational complexity and considerable network parameters, making the system unable to detect the signal timely in resource-constrained environments. This letter firstly proposes an efficient modulation recognition network(EMRNet) with tiny and low latency models to match the requirements for mobile reconnaissance equipments. One-dimensional residual depthwise separable convolutions block(1D-RDSB) with an adaptive size of receptive fields is developed in EMRNet to replace the traditional convolution block. With 1D-RDSB, EMRNet achieves a high classification accuracy and dramatically reduces computation cost and network paraments. The experiment results show that EMRNet can achieve higher precision than existing 2D-CNN methods, while the computational cost and parament amount of EMRNet are reduced by about 13.93× and 80.88×, respectively.

Previously, convolutional neural networks have made tremendous progress in target recognition based on micro-Doppler radar. However, these studies only considered the presence of one target at a time in the surveillance area. Simultaneous multi-targets recognition for surveillance radar remains a pretty challenging issue. To alleviate this issue, this letter develops a multi-instance multi-label (MIML) learning strategy, which can automatically locate the crucial input patterns that trigger the labels. Benefitting from its powerful target-label relation discovery ability, the proposed framework can be trained with limited supervision. We emphasize that only echoes from single targets are involved in training data, avoiding the preparation and annotation of multi-targets echo in the training stage. To verify the validity of the proposed method, we model two representative ground moving targets, i.e., person and wheeled vehicles, and carry out numerous comparative experiments. The result demonstrates that the developed framework can simultaneously recognize multiple targets and is also robust to variation of the signal-to-noise ratio (SNR), the initial position of targets, and the difference in scattering coefficient.

As ransomware inevitably overwrites existing data, SSDs can detect ransomware attacks by monitoring overwrites. The state-of-the-art technology uses a hash to monitor overwrites, which consumes tens of bytes of memory per I/O. To improve memory efficiency, we propose a bitmap-based overwrite detection method that uses only one bit per I/O.

In this letter, we propose a feature-based knowledge distillation scheme which transfers knowledge between intermediate blocks of teacher and student with flow-based architecture, specifically Normalizing flow in our implementation. In addition to the knowledge transfer scheme, we examine how configuration of the distillation positions impacts on the knowledge transfer performance. To evaluate the proposed ideas, we choose two knowledge distillation baseline models which are based on Normalizing flow on different domains: CS-Flow for anomaly detection and SRFlow-DA for super-resolution. A set of performance comparison to the baseline models with popular benchmark datasets shows promising results along with improved inference speed. The comparison includes performance analysis based on various configurations of the distillation positions in the proposed scheme.

We propose Quality Enhancement via a Side bitstream Network (QESN) technique for lossy image compression. The proposed QESN utilizes the network architecture of deep image compression to produce a bitstream for enhancing the quality of conventional compression. We also present a loss function that directly optimizes the Bjontegaard delta bit rate (BD-BR) by using a differentiable model of a rate-distortion curve. Experimental results show that QESN improves the rate by 16.7% in the BD-BR compared to Better Portable Graphics.

Involving higher-order thinking in learning activities can produce meaningful learning. It impacts the student's ability to solve problems in new situations. Concept mapping is a learning strategy that has been proven to promote higher-order thinking. Concept map recomposition (KB-mapping) in the Kit-Build system is a closed concept mapping where learners are given concepts and links to build a concept map, and it has advantage that the recomposed map can be automatically diagnosed. It has been proven that KB-mapping improves the students' learning achievement similar to the traditional concept mapping called scratch concept map composition (SC-mapping). However, the study on the effect of KB-mapping in fostering students' higher-order thinking has yet to be evaluated. This study designed and conducted an experiment to compare the impact of KB-mapping and SC-mapping on promoting students' ability in higher-order thinking. Fifty-four undergraduate students were assigned to either KB-Mapping or SC-Mapping for learning activities. The result of this study suggested that students who learn with KB-mapping had better abilities to solve questions of higher-order thinking than those who applied SC-mapping. The findings also suggested that the quality of students' concept maps affected their performance in solving higher-order thinking questions.

The design and adjustment of the divergence in audio applications using nonnegative matrix factorization (NMF) is still open problem. In this study, to deal with this problem, we explore a representation of the divergence using neural networks (NNs). Instead of the divergence, our approach extends the multiplicative update algorithm (MUA), which estimates the NMF parameters, using NNs. The design of the extended MUA incorporates NNs, and the new algorithm is referred to as the deep MUA (DeMUA) for NMF. While the DeMUA represents the algorithm for the NMF, interestingly, the divergence is obtained from the incorporated NN. In addition, we propose theoretical guides to design the incorporated NN such that it can be interpreted as a divergence. By appropriately designing the NN, MUAs based on existing divergences with a single hyper-parameter can be represented by the DeMUA. To train the DeMUA, we applied it to audio denoising and supervised signal separation. Our experimental results show that the proposed architecture can learn the MUA and the divergences in sparse denoising and speech separation tasks and that the MUA based on generalized divergences with multiple parameters shows favorable performances on these tasks.

The estimation problem of structured clutter covariance matrix (CCM) in space-time adaptive processing (STAP) for airborne radar systems is studied in this letter. By employing the prior knowledge and the persymmetric covariance structure, a new estimation algorithm is proposed based on the whitening ability of the covariance matrix. The proposed algorithm is robust to prior knowledge of different accuracy, and can whiten the observed interference data to obtain the optimal solution. In addition, the extended factored approach (EFA) is used in the optimization for dimensionality reduction, which reduces the computational burden. Simulation results show that the proposed algorithm can effectively improve STAP performance even under the condition of some errors in prior knowledge.

In this paper, a novel reconfigurable intelligent surface (RIS)-aided full-duplex (FD) cooperative non-orthogonal multiple access (CNOMA) network is investigated over Nakagami-m fading channels, where two RISs are employed to help the communication of paired users. To evaluate the potential benefits of our proposed scheme, we first derive the closed-form expressions of the outage probability. Then, we derive users' diversity orders according to the asymptotic approximation at high signal-to-noise-ratio (SNR). Simulation results validate our analysis and reveal that users' diversity orders are affected by their channel fading parameters, the self-interference of FD, and the number of RIS elements.

Fractional Frequency Reuse (FFR), which was introduced by 3GPP is considered the powerful technique to improve user performance. However, implementation of FFR is a challenge due to strong dependence between base stations (BSs) in terms of resource allocations. This paper studies a modified and flexible FFR scheme that allows all BSs works independently. The analytical and simulation results prove that the modified FFR scheme outperforms the conventional FFR.

In order to improve the anomaly detection efficiency of network traffic, firstly, the model is established for network flows based on complex networks. Aiming at the uncertainty and fuzziness between network traffic characteristics and network states, the deviation extent is measured from the normal network state using deviation interval uniformly, and the intuitionistic fuzzy sets (IFSs) are established for the various characteristics on the network model that the membership degree, non-membership degree and hesitation margin of the IFSs are used to quantify the ownership of values to be tested and the corresponding network state. Then, the knowledge measure (KM) is introduced into the intuitionistic fuzzy weighted geometry (IFWGω) to weight the results of IFSs corresponding to the same network state with different characteristics together to detect network anomaly comprehensively. Finally, experiments are carried out on different network traffic datasets to analyze the evaluation indicators of network characteristics by our method, and compare with other existing anomaly detection methods. The experimental results demonstrate that the changes of various network characteristics are inconsistent under abnormal attack, and the accuracy of anomaly detection results obtained by our method is higher, verifying our method has a better detection performance.

This paper introduces a deep reinforcement learning approach to solve the virtual network function scheduling problem in dynamic scenarios. We formulate an integer linear programming model for the problem in static scenarios. In dynamic scenarios, we define the state, action, and reward to form the learning approach. The learning agents are applied with the asynchronous advantage actor-critic algorithm. We assign a master agent and several worker agents to each network function virtualization node in the problem. The worker agents work in parallel to help the master agent make decision. We compare the introduced approach with existing approaches by applying them in simulated environments. The existing approaches include three greedy approaches, a simulated annealing approach, and an integer linear programming approach. The numerical results show that the introduced deep reinforcement learning approach improves the performance by 6-27% in our examined cases.

In this paper, we investigate the Access Point (AP) selection problem in Cell-Free Massive multiple-input multiple-output (MIMO) system. Firstly, we add a connecting coefficient to the uplink data transmission model. Then, the problem of AP selection is formulated as a discrete combinatorial optimization problem which can be dealt with by the particle swarm algorithm. However, when the number of optimization variables is large, the search efficiency of the traditional particle swarm algorithm will be significantly reduced. Then, we propose an ‘user-centric’ cooperative coevolution scheme which includes the proposed probability-based particle evolution strategy and random-sampling-based particle evaluation mechanism to deal with the search efficiency problem. Simulation results show that proposed algorithm has better performance than other existing algorithms.

Autonomous driving technology is expected to be applied to various applications with unmanned vehicles (UVs), such as small delivery vehicles for office supplies and smart wheelchairs. UV remote control by a cloud server (CS) would achieve cost-effective applications with a large number of UVs. In general, dead time in real-time feedback control reduces the control accuracy. On remote path tracking control by the CS, UV control accuracy deteriorates due to transmission delay and jitter through the Internet. Digital twin computing (DTC) and jitter buffer are effective to solve this problem. In our previous study, we clarified effectiveness of them in UV remote control by CS. The jitter buffer absorbs the transmission delay jitter of control signals. This is effective to achieve accurate UV remote control. Adaptive buffering time optimization according to real-time transmission characteristics is necessary to achieve more accurate UV control in CS-based remote control system with DTC and jitter buffer. In this study, we proposed a method for the adaptive optimization according to real-time transmission delay characteristics. To quantitatively evaluate the effectiveness of the method, we created a UV remote control simulator of the control system. The results of simulations quantitatively clarify that the adaptive optimization by the proposed method improves the UV control accuracy.

Hardware oriented security and trust of semiconductor integrated circuit (IC) chips have been highly demanded. This paper outlines the requirements and recent developments in circuits and packaging systems of IC chips for security applications, with the particular emphasis on protections against physical implementation attacks. Power side channels are of undesired presence to crypto circuits once a crypto algorithm is implemented in Silicon, over power delivery networks (PDNs) on the frontside of a chip or even through the backside of a Si substrate, in the form of power voltage variation and electromagnetic wave emanation. Preventive measures have been exploited with circuit design and packaging technologies, and partly demonstrated with Si test vehicles.

This paper proposes a layer-wise tunable retraining method for edge FeFET Computation-in-Memory (CiM) to compensate the accuracy degradation of neural network (NN) by FeFET device errors. The proposed retraining can tune the number of layers to be retrained to reduce inference accuracy degradation by errors that occur after retraining. Weights of the original NN model, accurately trained in cloud data center, are written into edge FeFET CiM. The written weights are changed by FeFET device errors in the field. By partially retraining the written NN model, the proposed method combines the error-affected layers of NN model with the retrained layers. The inference accuracy is thus recovered. After retraining, the retrained layers are re-written to CiM and affected by device errors again. In the evaluation, at first, the recovery capability of NN model by partial retraining is analyzed. Then the inference accuracy after re-writing is evaluated. Recovery capability is evaluated with non-volatile memory (NVM) typical errors: normal distribution, uniform shift, and bit-inversion. For all types of errors, more than 50% of the degraded percentage of inference accuracy is recovered by retraining only the final fully-connected (FC) layer of Resnet-32. To simulate FeFET Local-Multiply and Global-accumulate (LM-GA) CiM, recovery capability is also evaluated with FeFET errors modeled based on FeFET measurements. Retraining only FC layer achieves recovery rate of up to 53%, 66%, and 72% for FeFET write variation, read-disturb, and data-retention, respectively. In addition, just adding two more retraining layers improves recovery rate by 20-30%. In order to tune the number of retraining layers, inference accuracy after re-writing is evaluated by simulating the errors that occur after retraining. When NVM typical errors are injected, it is optimal to retrain FC layer and 3-6 convolution layers of Resnet-32. The optimal number of layers can be increased or decreased depending on the balance between the size of errors before retraining and errors after retraining.

It is very important to design an embedded real-time system as a fault-tolerant system to ensure dependability. In particular, when a power failure occurs, restart processing after power restoration is required in a real-time system using a conventional processor. Even if power is restored quickly, the restart process takes a long time and causes deadline misses. In order to design a fault-tolerant real-time system, it is necessary to have a processor that can resume operation in a short time immediately after power is restored, even if a power failure occurs at any time. Since current embedded real-time systems are required to execute many tasks, high schedulability for high throughput is also important. This paper proposes a non-stop microprocessor architecture to achieve a fault-tolerant real-time system. The non-stop microprocessor is designed so as to resume normal operation even if a power failure occurs at any time, to achieve little performance degradation for high schedulability even if checkpoint creations and restorations are performed many times, to control flexibly non-volatile devices through software configuration, and to ensure data consistency no matter when a checkpoint restoration is performed. The evaluation shows that the non-stop microprocessor can restore a checkpoint within 5µsec and almost hide the overhead of checkpoint creations. The non-stop microprocessor with such capabilities will be an essential component of a fault-tolerant real-time system with high schedulability.